Manuel d'utilisation / d'entretien du produit FM420 du fabricant Newland
Aller à la page of 156
FM420 Embedded 1D/2D Barcode Scanner Integration Guide V ersion 1.0.
nlscan.com Page 2 V ersion Description Date V ersion 1.0 Support as from FM420 fi rmware V ersion 3.06.021 and higher . 25-08-2010 Revisions.
Disclaimer © 1999-2008 by Newland Auto-ID T ech. Co., Ltd, All rights reserved. No part of this publication may be reproduced, transmitted, or used in any form or by any means, electrical or mechanical, without prior written permission from Newland Auto-ID.
nlscan.com Page I 请更换节标题 T able of Contents Content About this guide Introduction ................................................................................................................................................. 1 Graphic Notations .
nlscan.com Page II T able of Contents RS232 Interface Introduction ................................................................................................................................................ 25 Serial Port ........................
nlscan.com Page III T able of Contents 2 Digits Addenda Code ....................................................................................................................... 50 5 Digits Addenda Code .............................................
nlscan.com Page IV T able of Contents Code 93 ...................................................................................................................................................... 76 Load Factory Default ..............................
nlscan.com Page V T able of Contents QR Code .................................................................................................................................................. 101 Load Factory Default ..................................
nlscan.com Page VI T able of Contents Message Interception & Pack Introduction .............................................................................................................................................. 128 Message Interception .
nlscan.com Page 1 About this guide Introduction This FM420 Embedded 1D/2D Barcode Scanner Integration Guide provides general instructions for OEM integration. Graphic Notations T ool – Handy item for a task. Attention – Important subject to be aware of or to avoid.
nlscan.com Page 2 About this guide Newland Auto-ID Support Center If you have a problem with your equipment, contact the Newland Support Center in your region. Before call- ing, have the model number , serial number , and several of your barcodes at hand.
nlscan.com Page 3 Getting to Start Introduction FM420 is a 1D/2D barcode reader . Newland Auto-ID patented T M technology ensure FM420 fast image capture and accurate decoding. It provides the customer the best value. This chapter presents an overall picture of how to use FM420 step by step.
nlscan.com Page 4 Getting to Start Unpacking Unpacking Unpack FM420 and accessories. Check with the packing list. Make sure that there is no damage or missing part(s). If any damage or missing parts, please keep the original package and contact your supplier for services.
nlscan.com Page 5 Getting to Start Unpacking Data Interface Pin Function T ype Name 1 NC Null 2 NC Null 3 VCC P Power DC5V 4 TXD O Serial Port Output , RS232 5 RXD I Serial Port Input , RS232 6 NC.
nlscan.com Page 6 Getting to Start Communication Ports FM420 must connect to a Host to operate. A Host can be PC, POS, or any intelligent terminal with at least one of the following communication ports: USB, RS232, or PS/2. USB 1 、 RS232 2 、 RS232 port on Host : Please check the ports fi rst to order the fi tting cable.
nlscan.com Page 7 Getting to Start Connecting with USB Cable Insert USB Cable (RJ45 male head) into FM420 cable slot; 1 、 Insert USB Cable (USB male head) into Host ’ s (female) USB connector; 2 .
nlscan.com Page 8 Getting to Start Connecting with RS232 Cable Insert RS232 cable (RJ45 male head) into FM420 cable slot; 1 、 Insert RS232 cable (RS232 male head) into Host ’ s (female) RS232 conn.
nlscan.com Page 9 Getting to Start Decode Zones 36° 0 50 100 150 200 250 55mm PDF417(10mil) 175mm 45mm Data Matrix(10mil ) 145mm 45mm QR Code(10mil ) 140mm 35mm Code39(10mil) 170mm 55mm Code39(15.
nlscan.com Page 10 Getting to Start Speci fi cations Performance Image Sensor CMOS Resolution 752 * 480 Interface RS232 / USB 1.1 Symbologies 2D PDF417, QR Code(Model 1/2), DataMatrix(ECC200, ECC000, 050, 080,100,140), Aztec, Maxicode, etc.
nlscan.com Page 1 1 Getting to Start Dimensions of FM420 Unit FM420 T op V iew Figure 1. 5 0m m 6 0m m 2 6m m 1 2m m 1 0m m 9 m m 3 6m m 1 1 7 m m . M3 machine skew.
nlscan.com Page 12 Introduction There are 3 ways to program (con fi gure) the Engine, Code Programming, Command Programming, and QuickSet Programming.
nlscan.com Page 13 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Programming Notation Th is i s t he n ota ti on t o d is ab le th e Cod e Pr og ram mi ng .
nlscan.com Page 14 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Code Programming On/Off Re ad t he “ C od e P ro gr am min g ON ” b ar co de to a ct iva te “ Cod e Pr og ram - mi ng ” fun ct io n.
nlscan.com Page 15 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Illumination Il lu mi nat io n LED l ig ht ing u p bar co de s a re u se d t o ca ptu re b et ter i ma ges .
nlscan.com Page 16 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Aiming Th er e are 3 m ode s: “ A im Wink ” : L ED ke ep s fla sh in g w he n rea d.
nlscan.com Page 17 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Beep Decoding Beep Re ad “ Bee p ON ” t o en ab le al l dec od in g b ee p de not at io n a nd r ea d “ B ee p OFF ” to di sa bl e.
nlscan.com Page 18 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Beep Beep Denotation (Beeper De fi nitions) Beep Denotation low-higher-higher -higher .
nlscan.com Page 19 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Reading Mode Au to M ode : T he a mbi en t lu min an ce ch an ge in f ro nt of t he en gi ne au to - » ma ti ca lly i ni tia te s re adi ng .
nlscan.com Page 20 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Reading T imeout and Delay On e Re adi ng Tim eou t 【 Pro CMD : 0313000 】 Sa me B.
nlscan.com Page 21 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Sensitivity Se ns it ivi ty i s h ow s en sit iv e the e ng ine i s to am bi en t i ll um in ati on c han ge . » Se ns it ivi ty v alu e is [ 1 .
nlscan.com Page 22 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Exposure Imaging Mode ** Normal Exposure Mode 【 Pro CMD : 0321000 】 Re fl ection.
nlscan.com Page 23 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Default Factory Default Read “ Load All Factory Default ” to reset all parameters to factory default.
nlscan.com Page 24 Programming the Engine Programming the Engine Code Programming ON Code Programming OFF T ools Query Product Information Product information could be obtained by reading "Query Product Information" barcode. The engine will send it to the Host immediately .
nlscan.com Page 25 RS232 Interface Introduction When the engine is connected to the Host with RS232 cable, system will select RS232 connection by default. Under RS232 connection, the engine and the Host use the same communication parameters: baud rate, parity check, data bits select and stop bits select.
nlscan.com Page 26 RS232 Interface RS232 Interface Code Programming ON Code Programming OFF T ools Serial Port Baud Rate Baud rate is the number of bits of data transmitted per second. Set your scan engine baud rate to match the baud rate setting of the Host device.
nlscan.com Page 27 RS232 Interface RS232 Interface Code Programming ON Code Programming OFF T ools Parity Check Parity check options should be the same on the engine and the Host. Se le ct Od d pa rit y: I f dat a ha s a n od d n um be r of 1 bi ts, t he p ari ty b it » va lu e is se t to 0.
nlscan.com Page 28 RS232 Interface RS232 Interface Code Programming ON Code Programming OFF T ools Data Bits T ransmitted Se le ct da ta b its t ra ns mit te d to be 5 , 6 , 7 an d 8 . En sur e th e sel ec ti ons o n th e en gin e an d t he H os t a re t he sa me .
nlscan.com Page 29 USB Interface Introduction When using a USB connection, the default protocol is USB COM Port Emulation. USB DataPipe is a Newland Auto-ID Co., Ltd. developed protocol. The DataPipe driver should be installed on the Host. It supports data transmission and user preference programming.
nlscan.com Page 30 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW USB connection (no driver needed) supports simulating the Imager transmission to be a USB keyboard input. The Host receives keystrokes of the virtual keyboard.
nlscan.com Page 31 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW The keyboard arrangements and country codes vary in different countries. Refer country codes to the table “ USB Country Keyboard T ypes ” . Follow the steps mentioned below to program.
nlscan.com Page 32 USB Interface USB HID-KBW Country/Language Number Country/Language Number U.S. 0 Netherlands(Dutch) 14 Belgium 1 Norway 15 Brazil 2 Poland 16 Canada(French) 3 Portugal 17 Czechoslov.
nlscan.com Page 33 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW Unknown Characters, Beep HID-KBW deems an unknown character to be a character is not included in a country keyboard type. It may not be able to allocate and send a keystroke, thus lead to an error beep.
nlscan.com Page 34 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW Emulate AL T + keypad When enabled, full ASCII characters (0x00 ~ 0xff) can be sent over the numeric key- pad regardless country keyboard selections.
nlscan.com Page 35 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW Function Key Mapping When enabled, function characters (0x00~0x1F) are sent as ASCII sequences over the numeric keypad.
nlscan.com Page 36 USB Interface USB HID-KBW ASCII Function Key Mapping T able ASCII(HEX) Function key ASCII(HEX) Function Key 00 2 10 P 01 A 11 Q 02 B 12 R 03 C 13 S 04 D 14 T 05 E 15 U 06 F 16 V 07 G 17 W 08 H 18 X 09 I 19 Y 0A J 1A Z 0B K 1B [ 0C L 1C 0D M 1D ] 0E N 1E 6 0F O 1F .
nlscan.com Page 37 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW Keystroke Delay This parameter sets the delay , in milliseconds, between emulated keystrokes. Scan programming code below to increase the delay when the Host require a slower trans- mission of data.
nlscan.com Page 38 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW Convert Case The Imager converts all barcode messages to the selected case.
nlscan.com Page 39 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB HID-KBW Emulate Numeric Keypad When disable, the whole barcode message will be emulated as keystrokes on main keyboard. Read “ Emulate Numeric Keypad ” to enable the function.
nlscan.com Page 40 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB DataPipe This protocol is de fi ned by Newland Auto-ID. A driver has to be installed before using this protocol to communicate with reader , The advantage of using this protocol is the fast data transmission.
nlscan.com Page 41 USB Interface USB Interface Code Programming ON Code Programming OFF T ools USB COM Port Emulation When the USB port is connected to Host serial port in order to receive data from scanner , the model of imitating USB-to-RS232 has to be chosen.
nlscan.com Page 42 USB Interface USB Interface Code Programming ON Code Programming OFF T ools HID-POS Introduction The HID POS interface is recommended for new applications. It can send up to 56 characters in a single USB report and is muchfaster than keyboard emulation.
nlscan.com Page 43 USB Interface USB Interface Code Programming ON Code Programming OFF T ools HID-POS Access the Device in Y our Program CreateFile opens the device as a HID, then ReadFile delivers the scanned data to the application. Use W riteFile to send data to the device.
nlscan.com Page 44 Introduction This chapter lists all the available symbols and provides the programming barcodes to enable/disable them. Disabling reading of the symbols which do not apply , will improve reading performance. The few abling reading of the symbols are, the fast the engine will work.
nlscan.com Page 45 Symbols Code Programming ON Code Programming OFF T ools General Options Disable Reading All Disable Reading All = Allow reading Programming Codes only . Enable Reading All Enable Reading All = Enable to read all symbols and Programming Codes.
nlscan.com Page 46 Symbols Code Programming ON Code Programming OFF T ools General Options En ab le Re ad in g All 2 D Enable Reading All 2D 【 Pro CMD : 0001060 】 Di sa bl e R ea di ng Al l 2D D.
nlscan.com Page 47 Symbols Code Programming ON Code Programming OFF T ools Code 128 Lo ad F act or y Def au lt ** Load Code 128 Factory Default 【 Pro CMD : 0400000 】 En ab le /Di sa bl e C od e .
nlscan.com Page 48 Symbols Code Programming ON Code Programming OFF T ools Code 128 T o set Min Message Length of Code 128 to 8 bytes and Max Message Length to 12 bytes, read these programming codes .
nlscan.com Page 49 Symbols Code Programming ON Code Programming OFF T ools EAN-8 Lo ad F act or y Def au lt ** Load UCC/EAN-8 Factory Default 【 Pro CMD : 0401000 】 En ab le /Di sa bl e U CC /E A.
nlscan.com Page 50 Symbols Code Programming ON Code Programming OFF T ools EAN-8 2 Di gi ts Ad de nd a C od e Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code.
nlscan.com Page 51 Symbols Code Programming ON Code Programming OFF T ools EAN-8 EA N- 8 exp an d to EA N- 13 Expand EAN-8 to EAN-13, by adding 5 bytes of “ 0 ” to the left, and then transmit.
nlscan.com Page 52 Symbols Code Programming ON Code Programming OFF T ools EAN-13 Lo ad F act or y Def au lt ** Load EAN-13 Factory Default 【 Pro CMD : 0402000 】 Di sa bl e/E na bl eEA N- 13 ** .
nlscan.com Page 53 Symbols Code Programming ON Code Programming OFF T ools 5 Di gi ts Ad de nd a C od e 2 Di gi ts Ad de nd a C od e “ Enable 2 Digits Addenda Code “ — read an ordinary code and 2 digits Addenda Code. “ Enable 5 Digits Addenda Code “ — read an ordinary code and 5 digits Addenda Code.
nlscan.com Page 54 Symbols Code Programming ON Code Programming OFF T ools UPC-E Lo ad F act or y Def au lt ** Load UPC-E Factory Default 【 P ro C MD : 0 40 30 00 】 Di sa bl e/E na bl e U PC -E .
nlscan.com Page 55 Symbols Code Programming ON Code Programming OFF T ools 5 Di gi ts Ad de nd a C od e 2 Di gi ts Ad de nd a C od e “ Enable 2 Digits Addenda Code “ — read an ordinary code and 2 digits Addenda Code. “ Enable 5 Digits Addenda Code “ — read an ordinary code and 5 digits Addenda Code.
nlscan.com Page 56 Symbols Code Programming ON Code Programming OFF T ools UPC-E Tra ns mit D ef aul t “ 0 ” The fi rst byte of UPC-E is default to “ 0 ” .
nlscan.com Page 57 Symbols Code Programming ON Code Programming OFF T ools UPC-A Lo ad F act or y Def au lt ** Load UPC-A Factory Default 【 P ro C MD : 04 04 000 】 Di sa bl e/E na bl e U PC -A When the engine can not read UPC-A, please read “ Enable UPC-A ” and try again.
nlscan.com Page 58 Symbols Code Programming ON Code Programming OFF T ools 5 Di gi ts Ad de nd a C od e 2 Di gi ts Ad de nd a C od e “ Enable 2 Digits Addenda Code “ — read an ordinary code and 2 digits Addenda Code. “ Enable 5 Digits Addenda Code “ — read an ordinary code and 5 digits Addenda Code.
nlscan.com Page 59 Symbols Code Programming ON Code Programming OFF T ools Tra ns mit D ef aul t “ 0 ” The fi rst byte of UPC-A is default to “ 0 ” . UPC-A has the default “ 0 ” but it is not printed out, unlike UPC-E. Read “ T ransmit 0 ” will add a “ 0 ” to transmit.
nlscan.com Page 60 Symbols Code Programming ON Code Programming OFF T ools Interleaved 2 of 5 Lo ad F act or y Def au lt ** Load Interleaved 2 of 5 Factory Default 【 Pro CMD : 0405000 】 Di sa bl.
nlscan.com Page 61 Symbols Code Programming ON Code Programming OFF T ools Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Interleaved 2 of 5. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 62 Symbols Code Programming ON Code Programming OFF T ools Interleaved 2 of 5 Ch ec k Dig it Interleaved 2 of 5 may include Check Digit (not compulsory) following its barcode messages.
nlscan.com Page 63 Symbols Code Programming ON Code Programming OFF T ools Interleaved 2 of 5 Sp ec if ied L en gth s Program the engine to read speci fi ed lengths or ranges of speci fi ed lengths for Interleaved 2 of 5. The length value must be 3 decimal digits.
nlscan.com Page 64 Symbols Code Programming ON Code Programming OFF T ools ITF-14 ITF-14 is a fi xed length, 14 bytes Interleaved 2 of 5 barcode with Check digit. By factory default, it is disabled. Wh en e na bl ed , IT F- 14 p re ce de s 14 -b yt e In te rle av ed 2 o f 5 ba rc od e.
nlscan.com Page 65 Symbols Code Programming ON Code Programming OFF T ools ITF-6 ITF-6 is a fi xed length 6 bytes Interleaved 2 of 5 barcode with check digit.
nlscan.com Page 66 Symbols Code Programming ON Code Programming OFF T ools Matrix 2 of 5 ** Load Matrix 2 of 5 Factory Default 【 Pr o CM D : 0406000 】 Di sa bl e/E na bl e Mat ri x 2 of 5 Enable.
nlscan.com Page 67 Symbols Code Programming ON Code Programming OFF T ools Matrix 2 of 5 Min Message Length (default: 4) 【 Pr o CM D : 0406030 】 MaxMessage Length (default: 80) 【 Pr o CM D : 0406040 】 Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Matrix 2 of 5.
nlscan.com Page 68 Symbols Code Programming ON Code Programming OFF T ools Matrix 2 of 5 ** NO Check, T ransmit All 【 Pr o CM D : 0406050 】 Check, Do Not T ransmit Check Digit 【 Pr o CM D : .
nlscan.com Page 69 Symbols Code Programming ON Code Programming OFF T ools Code 39 Lo ad F act or y Def au lt ** Load Code 39 Factory Default 【 P ro C MD : 0 40 80 00 】 En ab le /Di sa bl e C od.
nlscan.com Page 70 Symbols Code Programming ON Code Programming OFF T ools Code 39 Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Code 39. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 71 Symbols Code Programming ON Code Programming OFF T ools Code 39 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to an error .
nlscan.com Page 72 Symbols Code Programming ON Code Programming OFF T ools Codabar Lo ad F act or y Def au lt ** Load Codabar Factory Default 【 Pro CMD : 0409000 】 En ab le /Di sa bl e C od ab ar When the engine can not read Codabar , please read “ Enable Codabar ” and try again.
nlscan.com Page 73 Symbols Code Programming ON Code Programming OFF T ools Codabar Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Codabar . The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 74 Symbols Code Programming ON Code Programming OFF T ools Codabar When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to an error .
nlscan.com Page 75 Symbols Code Programming ON Code Programming OFF T ools Codabar Tra ns mit S ta rt & St op Ch ar ac ter Codabar uses either one of “ A ” , “ B ” , “ C ” and “ D ” as the start character and the stop character . T ransmission of them can be selected.
nlscan.com Page 76 Symbols Code Programming ON Code Programming OFF T ools Code 93 Lo ad F act or y Def au lt ** Load Code 93 Factory Default 【 P ro C MD : 0 41 00 00 】 En ab le /D is ab le Co de 9 3 When the engine can not read Code 93, please read “ Enable Code 93 ” and try again.
nlscan.com Page 77 Symbols Code Programming ON Code Programming OFF T ools Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Code 93. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 78 Symbols Code Programming ON Code Programming OFF T ools Code 93 NO Check, T ransmit All 【 Pro CMD : 0410050 】 ** Check, Do not transmit Check Digit 【 Pro CMD : 0410060 】 Check, T ransmit All 【 Pro CMD : 04 10 070 】 Ch ec k Dig it Code 93 may include Check Digits (not compulsory) following its barcode message.
nlscan.com Page 79 Symbols Code Programming ON Code Programming OFF T ools UCC/EAN-128 Lo ad F act or y Def au lt ** Load UCC/EAN-128 Factory Default 【 P ro C MD : 0 41 20 00 】 En ab le /Di sa bl e U CC /E AN -12 8 When the engine can not read UCC/EAN-128, please read “ Enable UCC/EAN-128 ” and try again.
nlscan.com Page 80 Symbols Code Programming ON Code Programming OFF T ools GS1 Databar Lo ad F act or y Def au lt ** Load GS1 Databar Factory Default 【 Pro CMD : 0413000 】 Enable/Disable GS1 Databar When the engine can not read GS1 Databar , please read “ Enable GS1 Databar ” and try again.
nlscan.com Page 81 Symbols Code Programming ON Code Programming OFF T ools EAN·UCC Composite Lo ad F act or y Def au lt ** Load EAN·UCC Composite Factory Default 【 Pro CMD : 0414000 】 Enable/Disable EAN·UCC Composite When the engine can not read EAN·UCC Composite, please read “ Enable EAN·UCC Composite ” and try again.
nlscan.com Page 82 Symbols Code Programming ON Code Programming OFF T ools Code 1 1 Lo ad F act or y Def au lt ** Load Code 1 1 Factory Default 【 Pro CMD : 0415000 】 Enable/Disable Code 1 1 When the engine can not read Code 1 1, please read “ Enable Code 1 1 ” and try again.
nlscan.com Page 83 Symbols Code Programming ON Code Programming OFF T ools Code 1 1 Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Code 1 1. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 84 Symbols Code Programming ON Code Programming OFF T ools Code 1 1 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to an error .
nlscan.com Page 85 Symbols Code Programming ON Code Programming OFF T ools ISBN Load Factory Default ** Load ISBN Factory Default 【 Pro CMD : 0416000 】 Enable/Disable ISBN Enable ISBN 【 Pro CM.
nlscan.com Page 86 Symbols Code Programming ON Code Programming OFF T ools Industrial 25 Load Factory Default ** Load Industrial 25 Factory Default 【 Pro CMD : 0417000 】 Enable/Disable Industria.
nlscan.com Page 87 Symbols Code Programming ON Code Programming OFF T ools Industrial 25 Min Message Length (default: 6) 【 Pro CMD : 0417030 】 Max Message Length (default:48) 【 Pro CMD : 0417040 】 Se le ct M es sa ge L en gt h 1D bar code Message Length should not exceed 127 bytes.
nlscan.com Page 88 Symbols Code Programming ON Code Programming OFF T ools Industrial 25 ** NO Check, T ransmit All 【 Pro CMD : 0417050 】 Check, Do Not T ransmit Check Digit 【 Pro CMD : 0417.
nlscan.com Page 89 Symbols Code Programming ON Code Programming OFF T ools Standard 25 Load Factory Default ** Load Standard 25 Factory Default 【 Pro CMD : 04 18 00 0 】 Enable/Disable Standard 25 When the engine can not read Standard 25, please read “ Enable Standard 25 ” and try again.
nlscan.com Page 90 Symbols Code Programming ON Code Programming OFF T ools Standard 25 Min Message Length (default: 6) 【 Pro CMD : 0418030 】 Max Message Length (default:48) 【 Pro CMD : 0418040 】 Se le ct M es sa ge L en gt h 1D bar code Message Length should not exceed 127 bytes.
nlscan.com Page 91 Symbols Code Programming ON Code Programming OFF T ools Standard 25 ** NO Check, T ransmit All 【 Pro CMD : 0418050 】 Check, Do Not T ransmit Check Digit 【 Pro CMD : 041806.
nlscan.com Page 92 Symbols Code Programming ON Code Programming OFF T ools Plessey Load Factory Default ** Load Plessey Factory Default 【 Pro CMD : 04 19 00 0 】 Enable/Disable Plessey Enable Ple.
nlscan.com Page 93 Symbols Code Programming ON Code Programming OFF T ools Plessey Min Message Length (default: 4) 【 Pro CMD : 0419030 】 Max Message Length (default:48) 【 Pro CMD : 0419040 】 Se le ct M es sa ge L en gt h 1D bar code Message Length should not exceed 127 bytes.
nlscan.com Page 94 Symbols Code Programming ON Code Programming OFF T ools Plessey NO Check, T ransmit All 【 Pro CMD : 0419050 】 Check, Do Not T ransmit Check Digit 【 Pro CMD : 0419060 】 ** Check, T ransmit All 【 Pro CMD : 04 19 070 】 Ch ec k Dig it Plessey may include Check Digits (not compulsory) following its barcode message.
nlscan.com Page 95 Symbols Code Programming ON Code Programming OFF T ools MSI-Plessey Load Factory Default ** Load MSI-Plessey Factory Default 【 Pro CMD : 04 20 00 0 】 Enable/Disable MSI-Plesse.
nlscan.com Page 96 Symbols Code Programming ON Code Programming OFF T ools MSI-Plessey Min Message Length (default: 4) 【 Pro CMD : 0420030 】 Max Message Length (default:48) 【 Pro CMD : 0420040 】 Se le ct M es sa ge L en gt h 1D bar code Message Length should not exceed 127 bytes.
nlscan.com Page 97 Symbols Code Programming ON Code Programming OFF T ools MSI-Plessey NO Check, T ransmit All 【 Pro CMD : 0420050 】 ** Single Check Digit , MOD10 【 Pro CMD : 0420060 】 D.
nlscan.com Page 98 Symbols Code Programming ON Code Programming OFF T ools PDF417 Lo ad F act or y Def au lt ** Load PDF417 Factory 【 Pro CMD : 0501000 】 En ab le /Di sa bl e P DF 41 7 ** Enable.
nlscan.com Page 99 Symbols Code Programming ON Code Programming OFF T ools PDF417 Se le ct Me ss ag e L en gt h It is used to program the valid reading length of PDF417. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
nlscan.com Page 100 Symbols Code Programming ON Code Programming OFF T ools PDF417 ** Single PD F4 17 Only 【 Pro CMD : 0501070 】 T win PDF417 Only 【 Pro CMD : 0501080 】 Both Single & T win 【 Pro CMD : 0501090 】 PD F4 17 twin code is 2 PDF 41 7 barcodes paralleled vertically or horizontally .
nlscan.com Page 101 Symbols Code Programming ON Code Programming OFF T ools QR Code Lo ad F act or y Def au lt ** Load QR Code Factory Default 【 Pro CMD : 0502000 】 En ab le /Di sa bl e Q R Co de When the engine can not read QR Code, please read “ Enable QR Code ” and try again.
nlscan.com Page 102 Symbols Code Programming ON Code Programming OFF T ools QR Code Se le ct Me ss ag e L en gt h It is used to program the valid reading length of QR Code. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 103 Symbols Code Programming ON Code Programming OFF T ools QR Code QR twin code is 2 QR barcodes paralleled vertically or horizontally .They must have the same direction. Their speci fi cations must be similar and the distance between them must be short.
nlscan.com Page 104 Symbols Code Programming ON Code Programming OFF T ools Aztec Lo ad F act or y Def au lt ** Load Aztec Factory Default 【 Pro CMD : 0503000 】 En ab le /Di sa bl e Azt ec When the engine can not read Aztec, please read “ Enable Aztec ” and try again.
nlscan.com Page 105 Symbols Code Programming ON Code Programming OFF T ools Aztec Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Aztec. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
nlscan.com Page 106 Symbols Code Programming ON Code Programming OFF T ools Aztec Re ad in g M ul ti -ba rc od es of a n Ima ge ** Mode 1 【 Pro CMD : 0503070 】 Mode 2 【 Pro CMD : 0503080 】 Mode 3 【 Pro CMD : 0503090 】 There are three modes: Mode 1 : Read one barcode only .
nlscan.com Page 107 Symbols Code Programming ON Code Programming OFF T ools Aztec Th e nu mbe r of Mu lt i- ba rco de s ** 1 【 Pro CMD : 0503060 】 2 【 Pro CMD : 0503061 】 3 【 Pro CMD :.
nlscan.com Page 108 Symbols Code Programming ON Code Programming OFF T ools Data Matrix Lo ad F act or y Def au lt ** Load Data Matrix Factory Default 【 Pro CMD : 0504000 】 En ab le /Di sa bl e D at a Ma tri x When the engine can not read Data Matrix, please read “ Enable Data Matrix ” and try again.
nlscan.com Page 109 Symbols Code Programming ON Code Programming OFF T ools Data Matrix Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Data Matrix. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
nlscan.com Page 1 10 Symbols Code Programming ON Code Programming OFF T ools Data Matrix Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally .They must have the same direction. Their speci fi cations must be similar and the distance between them must be short.
nlscan.com Page 1 11 Symbols Code Programming ON Code Programming OFF T ools Data Matrix Re ct an gul ar S ymb ol s ** Enable Re ct an gul ar S ymb ol s 【 Pro CMD : 05041 10 】 Disable Re ct an g.
nlscan.com Page 1 12 Symbols Code Programming ON Code Programming OFF T ools Maxicode ** Load Maxicode Factory Default 【 Pro CMD : 0505000 】 En ab le /Di sa bl e Maxicode When the engine can not read Maxicode, please read “ Enable Maxicode ” and try again.
nlscan.com Page 1 13 Symbols Code Programming ON Code Programming OFF T ools Maxicode Min Message Length (default: 1) 【 Pro CMD : 0505030 】 Max Message Length (default:150) 【 Pro CMD : 0505040 】 Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Maxicode.
nlscan.com Page 1 14 Symbols Code Programming ON Code Programming OFF T ools Chinese Sensible Code ** Load Chinese Sensible Code Factory Default 【 Pro CMD : 0508000 】 Enable Chinese Sensible Cod.
nlscan.com Page 1 15 Symbols Code Programming ON Code Programming OFF T ools Chinese Sensible Code Min Message Length (default: 1) 【 Pro CMD : 0508030 】 Max Message Length (default:7827) 【 Pro CMD : 0508040 】 Se le ct Me ss ag e L en gt h It is used to program the valid reading length of Chinese Sensible Code.
nlscan.com Page 1 16 OCR OC R (O pt ic al C ha ra ct er R ec og ni ti on ) is t he te ch no lo gy t ha t ca pt ur es i ma ge o f pr in te d in fo rm at io n, a nd r ec og ni ze s th e im age t o ed it ab le c ha ra ct er s.
nlscan.com Page 1 17 Prefix/Suf fix Introduction 1D barcodes could contain digits, letters and symbols, etc. 2D barcodes could contain more data, such as Chinese characters and other multi-byte characters.
nlscan.com Page 1 18 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools General Programming Di sa bl e o r En abl e Pr ef ix/ Su ffi x Disable All Pre fi x/Suf fi x: T ransmit barcode message with no Pre fi x/Suf fi x.
nlscan.com Page 1 19 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools General Programming Pr ef ix Se qu en ces 6 options of Pre fi x Sequences: ** CodeID + AIM.
nlscan.com Page 120 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools General Programming User Pre fi x is added before barcode message. For example, if the user pre fi x is “ AB ” and the barcode message is “ 123 ” , the Host receives “ AB123 ” .
nlscan.com Page 121 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools AIM Pre fi x AIM (Automatic Identi fi cation Manufactures) de fi nes AIM pre fi x for many standard barcode formats.
nlscan.com Page 122 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools Code ID Pre fi x Besides AIM pre fi x, Code ID pre fi x can be used to denote barcode format and can be customized. The Code ID pre fi x MUST be one (1) or two (2) visible English letters.
nlscan.com Page 123 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools Modify PDF417 Code ID to be “ p ” (hex value is 0x70) 1. Read “ Code Programming ON ” 2. Read “ Modify PDF417 ” 3. Read Digit Code “ 7 ” , “ 0 ” 4.
nlscan.com Page 124 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools Code ID Pre fi x Modify EAN-8 【 Pro CMD : 0004040 】 Modify EAN-13 【 Pro CMD : 000.
nlscan.com Page 125 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools Code ID Pre fi x Modify Code 128 【 Pro CMD : 0004020 】 Modify UCC/EAN-128 【 Pro CMD.
nlscan.com Page 126 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools Program “ CODE ” as user suf fi x (The hex of “ CODE ” are 0x43, 0x4F , 0x44, and 0x45): 1. Read “ Code Programming ON ” 2. Read “ Program User Suf fi x ” 3.
nlscan.com Page 127 Pre fi x/Suf fi x Pre fi x/Suf fi x Code Programming ON Code Programming OFF T ools T erminal Disable or Enable T erminal “ T erminal ” is the termination for a string of barcode messages. It can not be formatted like other suf fi x and pre fi x.
nlscan.com Page 128 Message Interception & Pack Introduction Barcode message could divide information into different sections, such as product ID, manufacture ID, and so on. They are important overall. However , at certain situations, some of them are not of interest.
nlscan.com Page 129 Message Interception & Pack Message Interception & Pack Code Programming ON Code Programming OFF T ools Message Interception Interception Rule No.1: It only intercepts selected symbols ’ raw barcode messages and it effects all barcodes of the barcode format.
nlscan.com Page 130 Message Interception & Pack Message Interception & Pack Code Programming ON Code Programming OFF T ools Message Interception Pr og ra mmi ng 1 D I nt er ce pt Op ti on Note : Maximum sections of barcode message interception are 5.
nlscan.com Page 131 Message Interception & Pack Message Interception & Pack Code Programming ON Code Programming OFF T ools General Programming For example, intercept QR Code from 1st digit to 20th ascending and from 1 13th digit to 140th ascending.
nlscan.com Page 132 Message Interception & Pack Message Interception & Pack Code Programming ON Code Programming OFF T ools Message Pack Introduction Data Pack is for the special requirements of barcode message. There are 3 types of data pack.
nlscan.com Page 133 Batch Programming Introduction Batch Programming can integrate a programming sequence into one barcode. Batch Programming Rules: Sub-command is in this format: Programming Command + Parameters 1 、 Sub-commands are terminated by semicolons.
nlscan.com Page 134 Batch Programming How to build a batch command Batch command can contain many commands. Each command is divided by semicolon. Batch command must be ended with save command.
nlscan.com Page 135 Batch Programming Produce setting code Make the command list (ended with save command) to a PDF417, QR code or DataMatrix. For example, to produce a batch command means: light Always On, Auto Scan, change delay time to 2 seconds, Disable Fixed Length of I 2 of 5.
nlscan.com Page 136 Batch Programming Batch Programming Code Programming ON Code Programming OFF T ools Use batch setting code Code Programming ON 【 Pro CMD : 0006010 】 Allow Read Batch Code 【.
nlscan.com Page 137 Appendix Digit Code It is must to be read save after read digit code. 0 【 Pro CMD : 0000000 】 1 【 Pro CMD : 0000010 】 2 【 Pro CMD : 0000020 】 3 【 Pro CMD : 00.
nlscan.com Page 138 Appendix Digit Code 8 【 Pro CMD : 0000080 】 9 【 Pro CMD : 0000090 】 A 【 Pro CMD : 0000100 】 B 【 Pro CMD : 00001 10 】 C 【 Pro CMD : 0000120 】 D 【 Pro.
nlscan.com Page 139 Appendix Appendix Code Programming ON Code Programming OFF T ools Save and Abort In order to save the received data “ Save ” has to be read after data transition completed. If error occurs when reading data, the wrong data can be deleted and the setting up can be done again.
nlscan.com Page 140 Appendix Factory Default List Parameters Factory Default Remark General Programming Code Programming Off Send Pro Code V alue Off Illumination Illumination W ink Aiming Aiming W in.
nlscan.com Page 141 Appendix Factory Default List Parameters Factory Default Remark Symbol Code 128 Enable On Max Message Length 48 Min Message Length 1 EAN-8 Enable On Send Check Digit On Enable 2 Di.
nlscan.com Page 142 Appendix Factory Default List Min Message Length 6 No less than 4 Sp ec if ied L en gth s Off ITF-6 Enable Off ITF-14 Enable Off Matrix 2 of 5 Enable Off Check Off Send Check Digit.
nlscan.com Page 143 Appendix Factory Default List EAN•UCC Composite En ab le Off UPC/EAN Composite Enable Of f Code 1 1 En ab le Of f Se nd C hec k Di git O n 1 D ig it , M OD 11 C he ck On Ma x M.
nlscan.com Page 144 Appendix Factory Default List PDF417 En ab le On Re ad S ing le P DF4 17 O nl y On Ma x Me ssa ge L eng th 27 10 Mi n Me ssa ge L eng th 1 Re ad Forward Direction Barcode Only O n .
nlscan.com Page 145 Appendix AIM ID List Symbol AIM ID Possible AIM ID Modi fi ers(m) Code 128 ]C 0 UCC/EAN-128 ]C 1 EAN-8 ]E 4 EAN-13 ]E 0 EAN-13 with Addon ]E 3 UPC-E ]E 0 UPC-E with Addon ]E 3 UPC.
nlscan.com Page 146 Appendix Code ID List Symbol Code ID Code 128 j UCC/EAN-128 j EAN-8 d EAN-13 d UPC-E c UPC-A c Interleaved 2 of 5 e ITF-6 e ITF-14 e Ma tr ix 2 o f 5 v Code 39 b Codabar a Code 93 .
nlscan.com Page 147 Appendix Symbols ID Number Symbol ID Number Code 128 002 UCC/EAN-128 003 EAN-8 004 EAN-13 005 UPC-E 006 UPC-A 007 Interleaved 2 of 5 008 ITF-14 009 ITF-6 010 Matrix 2 of 5 01 1 Cod.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Newland FM420 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Newland FM420 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Newland FM420, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Newland FM420 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Newland FM420, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Newland FM420.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Newland FM420. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Newland FM420 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.