Manuel d'utilisation / d'entretien du produit NP200 du fabricant NEC
Aller à la page of 49
Portable Projector NP200/NP100 User ’ s Manual.
© NEC Display Solutions, Ltd. 2007 First edition December 2007 • DLP and BrilliantColor are trademarks of T exas Instruments. • IBM is a trademark or registered trademark of International Business Machines Corporation. • Macintosh, PowerBook, iMac, and Power Mac are trademarks of Apple, Inc.
i English ... Impor tant Inf or ma tion Safety Cautions Precautions Please read this manual carefully before using your NEC NP100/NP200 projector and keep the manual handy for future reference. CAUTION T o turn off main power , be sure to remove the plug from power outlet.
ii English ... Impor tant Infor mation RF Interference (for USA only) W ARNING The Federal Communications Commission does not allow any modications or changes to the unit EX - CEPT those specied by NEC Display Solutions of America, Inc. in this manual.
iii English ... Impor tant Infor mation Fire and Shock Precautions • Ensure that there is sufcient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector . Allow at least 4 inches (10cm) of space between your projector and a wall.
iv English ... Impor tant Infor mation Remote Control Precautions • Handle the remote control carefully . • If the remote control gets wet, wipe it dry immediately . • Avoid excessive heat and humidity . • Do not place the battery upside down.
1 ... English Table of Contents T able of Contents ......................................................................................... 1 Usage Notice ...............................................................................................
2 English ... Usage Notice Precautions Follow all warnings, precautions and maintenance as recom- mended in this user’s guide to maximize the life of your unit. ■ Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes.
3 ... English Usage Notice Do: ■ Turn off the product before cleaning. ■ Use a soft cloth moistened with mild detergent to clean the display housing. ■ Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
4 English ... Introduction Product Features This product is an SVGA/XGA single chip 0.55” DLP TM pro- jector. Outstanding features include: ■ NP100: True SVGA, 800 x 600 addressable pixels NP200: True XGA, 1024 x 768 addressable pixels ■ Single chip DarkChip2 TM DLP TM technology ■ NTSC/NTSC4.
5 ... English Introduction Power Cable US (P/N:79TC1031) EU (P/N: 79TC1041) CH (P/N: 79TC1051) VGA Cable (P/N : 79TC1001) Wireless Remote Control (P/N:79TC1021) Projector with lens cap (P/N:79TC1011) Package Overview This projector comes with all the items shown below.
6 English ... Introduction 1. Power 2. Remote Control 3. Power (LED indicator) 4. Zoom and Focus Rings 5. Speaker 6. Lens 7. Lens Cap 8. Ventilation (inlet) 9.
7 ... English Introduction Connection Ports 1. COMPUTER IN Connector 2. S-VIDEO IN Connector 3. VIDEO IN Connector 4. SERVICE Port 5. MONITOR OUT Connector 6.
8 English ... Introduction Wireless Remote Control 1 Power Refer to the “Power On/Off the Projector” section on pages 12-13. 2 Picture Mode Select the Picture mode from Presentation, Movie, sRGB, Game and User. 3 Computer Source Press “Computer” to choose Computer connector.
9 ... English Introduction 5 Keystone Correction Adjust the image to compensate for distortion caused by tilt- ing the projector (vertical ± 40 degrees).
10 English ... Introduction Battery Installation Remote Control Precautions • Handle the remote control carefully. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • Do not place the battery upside down.
11 ... English Installation Connecting the Projector Due to the differ- ence in applications for each country, some regions may have differ- ent accessories. To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with your projector.
12 English ... Installation Powering On the Projector 1. Ensure that the power cable and signal cable are securely connected. The Power LED will ash blue. 2. Remove the lens cap. 3. Turn on the lamp by pressing “Power” on the control panel.
13 ... English Installation Powering Off the Projector 1. Press the “Power” to turn off the projector lamp, you will see a message as below on the on-screen display. 2. Press the “Powe r” again to conrm. 3. The cooling fan continues to operate for abo ut 120 seconds during the cool down period and the Power LED will ash blue.
14 English ... Installation Warning Indicator When the “Power” LED i ndicator turns red, it indicates the projector has overheated. The projector will auto matically shut itself down.
15 ... English Installation Adjusting the Projected Image Adjusting the Height of Projector Image The projector is equipped with adjustable feet to raise and lower the image to ll the screen. To raise/lower the image: 1. Use to ne-tune the display angle .
16 English ... Installation Max. 30.3"(76.9cm ) 75.7"(192.3cm) 126.2"(320.5cm ) 176.7"(448.7cm) 227.1" (576.9cm) 302.8"(769.2cm) Min. 27.5"(69.8cm) 68.7"(174.4cm) 114.4" (290.7cm) 160.2"(407.0cm) 206.0" (523.
17 ... English User Controls The Projector has a multilingual On Screen Display that allows you to make image adjustments and change a variety of set- tings. The projector will automatically detect the source. How to operate 1. To open the OSD, press “Menu” on the Remote Control.
18 English ... User Controls Image (PC Mode) Picture Mode There are many factory presets optimized for various types of im - ages. Use the or to select the item. Presentation: For computer or notebook. Movie: For home theater. sRGB: For standard color.
19 ... English User Controls Clock “Clock” changes the display data frequency to match the frequency of your computer’s graphic card. If you experience a vertical icker - ing bar, use this function to make an adjustment. Phase Synchronize the signal timing of the projector with the graphics card.
20 English ... User Controls Image (Video Mode) Picture Mode There are many factory presets optimized for various types of im - ages. Use the or to select the item. Presentation: For computer or notebook. Movie: For home theater. sRGB: For standard color.
21 ... English User Controls Color Adjust a video imge from black and white to fully saturated color. Press the to decrease the amount of color in the image. Press the to increase the amount of color in the image. Hue Adjust the color balance of red and green.
22 English ... User Controls Display Setting Keystone Adjust image distortion caused by tilting projector. (±40 degrees). H-Position (Horizontal Position) Press the to move the image left. Press the to move the image right. V-Position (Vertical Position) Press the to move the image down.
23 ... English User Controls Orientation Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. Front-Ceiling When you select this function, the projector turns the image upside down for ceiling-mounted projection.
24 English ... User Controls Source Lock When this function is turned “Off”, the projector will search for other signals if the current input signal is lost. When this function is turned “On”, it will only search a specied connection port. Fan Control Choose “On” to turn on Fan Control mode.
25 ... English User Controls Audio Mute: ■ Choose “On” to mute the volume. ■ Choose “Off” to restore the volume. Volume: ■ Press the to decrease the volume. ■ Press the to increase the volume. Clear Lamp Hours Reset the lamp life hour after replacing a new lamp.
26 English ... User Controls Language Choose the multilingual OSD. Press into the sub menu and then use the or or or key to select your preferred language.
27 ... English User Controls Information To display the projector information on the screen. Information.
28 English ... Appendices Problem: No image appears on screen Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure the pins of connectors are not crooked or broken.
29 ... English Appendices 4. Verify the resolution setting is less than or equal to 1280 x 1024 resolution. 5. Select the “Change” under the “Monitor” tab . 6. Click on “Show all devices”. Next, select “Standard monitor types” under the SP box; choose the resolution mode you need under the “Models” box.
30 English ... Appendices Problem: Image has vertical ickering bar Use “Clock” to make an adjustment. Check and recongure the display mode of your graphic card to make it compatible with the product. Problem: Image is out of focus Adjust the Focus Ring on the projector lens.
31 ... English Appendices Steady light => No light => Message Power-LED (Blue) (Red) (Purple) Standby (Input power cable) Flashing (0.5 sec.) Power on (Warming up) Lamp lighting (Displaying) Power off (Cooling-I) Power off (Cooling-II) Flashing (0.
32 English ... Appendices Problem: Message Reminders Over temperature - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Replacing the lamp - the lamp is about to reach its maximum life- time.
33 ... English Appendices Replacing the lamp (optional lamp NP10LP) The projector will detect the lamp life at 3400 hours in Normal mode. When the “Power” LED indicator ashes red and the message below displays on-screen, the projector has detected that the lamp is approaching its end of life.
34 English ... Appendices Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power.
35 ... English Appendices Specications Projection System Single Chip DLP TM Technology by Texas Instruments Number of Pixels* NP100: 800 pixels(H) X 600 lines(V), up to SXGA (1280 X 1024) with scaling technology NP200: 1024 pixels(H) X 768 lines(V), up to SXGA+(1400 X 1050) with scaling technology Displayable Color 16.
36 English ... Appendices Compatibility Modes Modes Resolution V.Frequency (Hz) H.Frequency (kHz) VGA 640 x 480 60 31.50 640 x 480 72 37.90 640 x 480 75 37.50 640 x 480 85 43.30 720 x 400 70 31.50 720 x 400 85 37.90 SVGA 800 x 600 56 35.20 800 x 600 60 37.
37 ... English Appendices Cabinet Dimensions 10.7"/272mm 3.4"/86mm 1.7"/42mm 7.8"/199mm 3.2"/80mm 8.1"/206mm Lens Center.
Power No power (POWER indicator does not light blue). Power cable’s plug is fully inserted into the wall outlet. Lamp cover is installed correctly . Lamp Hours Used (lamp operation hours) was cleared after lamp replacement. No power even though you press and hold the POWER button for a minimum of 1 second.
In the space below please describe your problem in detail. Information on application and environment where your projector is used Projector Model number: Serial No.
T ravelCare Guide T ravelCare - a service for international travelers This product is eligible for “T ravelCare”, NEC’ s unique inter national warranty . Please note that T ravelCare coverage differs in par t from coverage under the warranty included with the product.
Hyosung ITX Co ., Ltd. Address: 2nd Fl., Ire B/D. #2, 4Ga, Y angpyeng-Dong, Y oungdeungpo-Gu, Seoul, Korea 150-967 T elephone: +82 2 2163 4193 F ax Line: +82 2 2163 4196 Email Address: moneybear@h yosung.com (Regions Covered) South Korea Lenso Communication Co .
T O: NEC or NEC’ s Authorized Service Station: FM : (Company & Name with signature) Dear Sir (s), I would like to apply your T rav elCare Ser vice Program based on attached registration and qual.
5. Loan Service Char ges and Conditions: Upon acceptance of this NEC Projector, Customer agrees to assume liability for this loan unit. The current cost of use of this loan unit is $200.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté NEC NP200 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du NEC NP200 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation NEC NP200, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le NEC NP200 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le NEC NP200, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du NEC NP200.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le NEC NP200. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei NEC NP200 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
