Manuel d'utilisation / d'entretien du produit MDview 193 du fabricant NEC
Aller à la page of 33
MDview Series User ’ s Guide MDview Series User ’s Guide Rev .5.
Index W arning, Caution ............................................................................................................... ......... English-1 Declaration ...................................................................................
English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET . DO NOT REMOVE COVER (OR BACK).
English-2 This Quick Reference Guide refers to the following NEC MDview Series 2 models - MDview 193 19" Display , 1.3 mega-pixel = 1280 x 1024 resolution (L195RR) - MDview 202 20" Display , 2.0 mega-pixel = 1600 x 1200 resolution (L205GR) - MDview 213 21" Display , 2.
English English-3 Contents Y our new NEC monitor box* should contain the following: • MDview 193, 202, 213, 242 or 262 monitor with tilt/swivel/pivot/height adjust stand • Power Cord (European Con.
English-4 Figure C.1 Figure C.2 Highest Stand Position Quick Start To attach the LCD monitor to your system, follow these instructions: 1. T urn off the power to your computer . 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.
English English-5 Figure E.1 V acation Switch Power Button Figure C.3 Figure D.1 Figure D.2 Figure C.4 7. Hold all cables firmly and place the cable cover onto the stand ( Figure D.1 ). T o remove the cable cover , lift the cover off as shown in Figure D.
English-6 Tilt Grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired ( Figure TS.1 ). Figure TS.1 Swivel Grasp both sides of the monitor screen with your hands and adjust the swivel as desired ( Figure TS.2 ).
English English-7 Figure S.1 4. Place one hand around the base and one hand on the Quick Release Lever . Move the Quick Release Lever in the direction indicated by the arrows ( Figure S.2 ). 5. Lift up the bottom of the stand to unhook it from the monitor ( Figure S.
English-8 Controls OSD (On-Screen-Display) control buttons on the front of the monitor function as follows: To access OSD menu, press any of the control buttons (EXIT , LEFT , RIGHT , UP , DOWN). To change signal input, press the SELECT button. NOTE: OSD must be closed in order to change signal input.
English English-9 ECO MODE Decreases the amount of power consumed by reducing the brightness level. 1: Decreases the brightness by 25%. 2: Decreases the brightness by 50%. CUSTOM: Decreases the brightness level as determined by the user . Refer to the Advanced OSD menu for custom setting instructions.
English-10 AUTO FINE (Analog input only) This function automatically and periodically adjusts the “FINE” setting for change in signal condition. This function adjusts approximately every 33 minutes. EXP ANSION Sets the zoom method. FULL: The image is expanded to the MDview model’s native mode, regardless of the resolution.
English English-11 OFF TIMER Monitor will automatically power-down when the end user has selected a pre-determined amount of time. Before powering off, a message will appear on the screen asking the user if they want to delay the turn of f time by 60 minutes.
English-12 RESOLUTION NOTIFIER This optimal resolution depends on the MDview model’s native resolution. If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not at the respective MDview model’ s native resolution - 1280 x 1024 or 1600 x 1200 or 1920 x 1200.
English English-13 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOUR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-14 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English English-15 Specifications - MDview 193 Monitor Specifications NEC MDview 193 Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 48.2 cm/19.0 inches crystal display (LCD); 0.
English-16 Specifications - MDview 202 Monitor Specifications NEC MDview 202 Monitor Notes LCD Module Diagonal: 51 cm/20.1 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 51 cm/20.
English English-17 Specifications - MDview 213 Monitor Specifications NEC MDview 213 Monitor Notes LCD Module Diagonal: 54 cm/21.3 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 54 cm/21.3 inches crystal display (LCD); 0.
English-18 Specifications - MDview 242/242-2 Monitor Specifications NEC MDview 242/242-2 Monitor Notes LCD Module Diagonal: 61.1 cm/24.1 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 61.1 cm/24.1 inches liquid crystal display (LCD); 0.
English English-19 Specifications - MDview 262/262-2 Monitor Specifications NEC MDview 262/262-2 Monitor Notes LCD Module Diagonal: 64.9 cm/25.5 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 64.9 cm/25.5 inches liquid crystal display (LCD); 0.
English-20 Features Ambix3 T echnology: T riple input technology allowing up to 3 input sources to be connected to a single monitor . The DVI-I connector supports both analog and digital input signals. Legacy analog input is supported using a traditional 15-pin VGA connector.
English English-21 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position.
English-22 Appendix If you need detailed information about the controls, please use the advanced menu. <How to use the advanced menu> •T urn of f your monitor . •T urn on your monitor by pushing the “POWER” and “INPUT/SELECT” button at the same time for at least one second simultaneously .
English English-23 T ag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust. (Analog input only) G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust.
English-24 H. Size Adjusts the horizontal size of the screen. (Analog input only) If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be performed using the “H.Size (V .Size)” function (dot clock).
English English-25 T ag6 Color Control Colour Control Systems: Seven preset colour settings. For preset settings 1, 2, 3 and 5, the following levels can be adjusted: TEMPERA TURE: Adjust the white temperature by increasing or decreasing this setting.
English-26 OFF MODE The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of inactivity . The IPM has three settings. OFF: Monitor does not go into power save mode when the input signal is lost. ST ANDARD: Monitor enters power save mode automatically when the input signal is lost.
English English-27 BOOT LOGO The NEC logo is briefly displayed after the monitor is powered on. This feature can be turned on or off in the OSD. Note: If the “EXIT” button is kept pressed while NEC logo is displayed, the BOOT LOGO menu will appear .
English-28 Input Setting Video Bandwidth (Analog input only): It is used when the unnecessary noise from computer appears on a screen. It is strong ineffective, so that a number becomes small. Press “Left” or “Right” to select. Sync Threshold (Analog input only): Adjusts the slice level of a synchronization signal.
English English-29 T agC Schedule Programs the monitor ’s working schedule. Schedule the power on and power of f with hour and a day of the week. Also sets the input port. This OSD can’t remove except EXIT . Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.
English-30 PICTURE MODE function - MDview 242-2 and 262-2 Choose the Picture mode that is most suitable for the type of content that is shown. There are five types of mode (ST ANDARD, sRGB, PROGRAMMABLE, Adobe ® RGB and MEDICAL). •T o access the Picture mode, press Reset button while OSD menu is not showing.
English English-31 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté NEC MDview 193 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du NEC MDview 193 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation NEC MDview 193, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le NEC MDview 193 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le NEC MDview 193, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du NEC MDview 193.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le NEC MDview 193. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei NEC MDview 193 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
