Manuel d'utilisation / d'entretien du produit 425007x92B du fabricant Murray
Aller à la page of 52
The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT P ARTS and the W ARRANTIES. This information must be included to make sure state laws and other laws are followed.
2 F-030721L T ABLE OF CONTENTS W ARRANTY 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESPONSIBILITY OF THE OWNER 3 . . . . . . . . . . . . . . . . . SAFETY RULES 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
OWNER’S INFORMA TION 3 F-030721L This instruction book is for several different models. The instructions ar e written for a person with some mechanical ability . Like most ser- vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability .
OWNER’S INFORMA TION 4 F-030721L b. Limit loads to those you can safely control. c. Do not turn sharply . Use care when backing. d. Use counterweights or wheel weights when suggested in the Instruction Book.
SAFE MOWING GUIDE 5 F-030721L Each person that operates power equipment must learn to use correct and safe mowing procedures. T o help you learn, carefully read the following pages. Most of the time the operator was not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit.
SAFE MOWING GUIDE 6 F-030721L mower was completely assembled at the store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil.
SAFE MOWING GUIDE 7 F-030721L Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate. If the weather conditions are bad, do not mow .
STEPS T O FOLLOW 8 F-030721L BEFORE MOWING F Be sure to dress correctly . Wear hard shoes, not sandals or tennis shoes. F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade. F Fill the fuel tank outside.
INTERNA TIONAL PICTORIALS 9 F-030721L INTERNA TIONAL PICT ORIALS IMPORT ANT : Some of the following pic- torials are located on your unit or on literature supplied with the product. Be- fore you operate the unit, learn and un- derstand the purpose for each pictorial.
ASSEMBL Y 10 F-030721L ASSEMBL Y This instruction book is for several models. Some parts or accesso- ries are not included on all models. Read and follow the assembly and adjustment instructions for your mower . All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled.
ASSEMBL Y 11 F-030721L HOW TO INST ALL THE SEA T Us e the fasteners shown below to install the seat . The fasteners are shown at full size. (A) 1001054 (B) 17x47 1. Carefully remove the plastic bag from the seat. 2. Align the holes in the seat hinge to the holes in the seat (Figure 1).
ASSEMBL Y 12 F-030721L MAINTENANCE FREE BA TTER Y IMPORT ANT : Before you attach the battery cables to the battery , check the battery date. The battery date tells if the battery must be charged. 1. Check the top of the battery for the location of the battery date (Figure 4).
ASSEMBL Y 13 F-030721L IMPORT ANT! BEFORE YOU ST ART MOWING - Check the engine oil. - Fill the fuel tank with gasoline. - Check the level of the mower housing. - Check the air pressure of the tires. - Make sure the battery cables are attached. W ARNING: Before doing any assembly or mainte- nance to the mower , remove the wire from the spark plug.
OPERA TION 14 F-030721L Figure 5 Throttle Control Lever Blade Rotation Control Clutch / Brake Pedal Lift Lever Shift Lever LOCA TION OF CONTROLS BLADE RO T A TION CONTROL: Use the blade rotation control to start and stop the rotation of the blades. CLUTCH / BRAKE PEDAL: The pedal has two functions.
OPERA TION 15 F-030721L A TT ACHMENTS This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper , a lawn aerator , a hopper spreader , or a small trailer . This unit can not use attachments that engage the ground like a plow , a disk harrow , or a cultivator.
OPERA TION 16 F-030721L HOW TO SET THE P ARKING BRAKE 1. Completely push the clutch/brake pedal forward. 2. Lift the parking brake lever (Figure 7). 3. Remove your foot from the clutch/brake pedal and then release the parking brake lever . Make sure the parking brake will hold the unit.
OPERA TION 17 F-030721L HOW TO OPERA TE WITH THE MOWER HOUSING W ARNING: The d e f lector is a safety device. Do not r e - move the deflector . The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position.
OPERA TION 18 F-030721L BEFORE ST ARTING THE ENGINE CHECK THE OIL NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer ’s instructions for the type of gasoline and oil to use.
OPERA TION 19 F-030721L OPERA TING TIPS 1. Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly , the adjustment must be cor- rect. 2. Before you use the unit, check the oil in the engine and add oil if necessary .
MAINTENANCE 20 F-030721L MAINTENANCE CHART FREQUENCY MAINTENANCE REQUIRED COMMENTS Daily or before each use Maintenance engine. Refer to the Engine Owner ’ s Manual. Examine blade(s). Check for cracks, wear , and excessive damage. Remove debris from unit and mowing area .
MAINTENANCE 21 F-030721L INSPECT BLADE W ARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.
MAINTENANCE 22 F-030721L HOW TO ADJUST THE BLADE ROT A TION CONTROL W ARNING: T o prevent an injury , the blade rotation control must operate correctly . In normal usage, the blade rotation control will not require an adjustment. However , if the cutting performance decreases or the quality of cut is poor , make the following changes.
MAINTENANCE 23 F-030721L HOW TO CHECK AND ADJUST THE DRIVE BRAKE Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads.
MAINTENANCE 24 F-030721L HOW TO ADJUST THE SHIFT LEVER If the NEUTRAL position on the shift lever does not match neutral on the gearbox, adjust the shift lever as follows. 1. Stop the engine. 2 . Disconnect the adjuster nut from the shifter bracket (Figure 18).
MAINTENANCE 25 F-030721L WHERE TO LUBRICA TE Lubricate the areas shown with engine oil. Apply grease with a brush to the areas shown. Models with grease fittings: Lubricate with grease gun. NOTE: Apply grease to the steering gear assembly . CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit.
W ARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST- MENT position. Level Adjustment Position Figure 22 MAINTENANCE 26 F-030721L HOW TO REMOVE THE MOWER HOUSING 1. Move the blade rotation control to the DISENGAGE position.
MAINTENANCE 27 F-030721L HOW TO ADJUST THE GAUGE WHEELS The axle bolts for the gauge wheels were mounted in the LOW cut position. T o change the position of the gauge wheels, move the axle bolts as follows. IMPORT ANT : Before you adjust the gauge wheels, you must do the following.
MAINTENANCE 28 F-030721L HOW TO LEVEL THE MOWER HOUSING If the mower housing is level, the blade will cut easier and the lawn will look better . W ARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug.
MAINTENANCE 29 F-030721L HOW TO REPLACE THE MOTION DRIVE BEL T REMOV AL 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Completely push the pedal forward and engage the parking brake. 3. Remove the idler pulley (Figure 30).
MAINTENANCE 30 F-030721L INST ALLA TION 1. Slide the motion drive belt between the stack pulley and the belt guides (Figure 33). Install the motion drive belt on the to p pulley of the stack pulley . Make sure the “V” side of the belt is against the pulley .
MAINTENANCE 31 F-030721L HOW TO REPLACE THE MOWER DRIVE BEL T 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 36).
MAINTENANCE 32 F-030721L HOW TO INST ALL THE WHEELS If the wheels must be removed for service, make sure they are installed as follows. Front Wheel 1. Make sure the valve stem is to the outside of the tractor . Slide the front wheel on the spindle (See Figure 37).
MAINTENANCE 33 F-030721L HOW TO REPLACE THE FUSE If the fuse is blown, the engine will not start. The location of the fuse is next to the battery . Remove the fuse and replace with a automotive fuse (Figure 39). Figure 39 Automotive Fuse HOW TO REPLACE THE LIGHT BULB 1.
TROUBLE SHOOTING CHART 34 F-030721L PROBLEM: The engine will not start. 1. Follow the steps, “How T o Start The Engine” in this book. 2. Electric-Start Models: Clean the battery terminals. T ighten the cables. 3. Drain the fuel tank. Clean the fuel line.
F-030721L 35 Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where th e unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone directory .
REP AIR P ARTS MODEL 425007x92B 36 F-030721L CHASSIS & HOOD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24 21 22 23 25 26 27 28 29 28 20 31 32 33 34 35 31 36 37 38 16 39 40 41 42 50 16 16 4.
REP AIR P ARTS MODEL 425007x92B 37 F-030721L CHASSIS & HOOD Key No. Description Part No. Key No. Description Part No. 1 Seat 690566 2 Cap, Push 0n 028x23 3 Spring 094057 4 Screw 26x229 5 Bolt, Win.
REP AIR P ARTS MODEL 425007x92B 38 F-030721L MOTION DRIVE 1 2 3 4 5 6 7 8 9 10 12 11 13 14 15 16 60 18 19 20 17 21 6 55 22 23 25 26 27 28 30 31 32 33 35 17 41 29 17 34 39 40 38 45 37 46 49 48 50 53 51.
REP AIR P ARTS MODEL 425007x92B 39 F-030721L MOTION DRIVE Key No. Description Part No. Key No. Description Part No. 1 Bolt, Shoulder 009x39 2 Nut, Hex 015x89 3 Arm, Idler 690173E701 4 Rod, Clutch 0940.
REP AIR P ARTS MODEL 425007x92B 40 F-030721L STEERING 1 2 3 4 5 6 7 8 9 10 11 12 15 6 13 30 30 30 17 18 30 14 30 19 16 26 24 21 22 23 25 27 24 25 22 23 28 29 25 25 30 33 35 36 19 31 31 32 38 20 20 37 .
REP AIR P ARTS MODEL 425007x92B 41 F-030721L STEERING Key No. Description Part No. 1 Wheel, Steering 094134 2 Post, Steering 690625 3 Clip, Retainer 094131 4 Bearing 094124 5 Nut, Flange 15x1 1 1 6 Bo.
REP AIR P ARTS MODEL 425007x92B 42 F-030721L MOWER HOUSING SUSPENSION 1 2 3 4 5 6 7 8 14 14 9 10 11 12 12 11 13 14 15 16 17 18 19 20 20 21 22 22 23 24 24 24 25 25 11 15 27 26 26 24 25 15 33 34 36 37 3.
REP AIR P ARTS MODEL 425007x92B 43 F-030721L MOWER HOUSING SUSPENSION Key No. Description Part No. Key No. Description Part No. 1 Grip 092698 2 Handle, PTO 094157 Z 3 Pad, Switch 094022 Z 4 Bolt 0025x.
REP AIR P ARTS MODEL 425007x92B 44 F-030721L MOWER HOUSING 1 2 3 61 2 1 4 5 11 10 47 13 1 4 15 16 17 18 23 22 9 19 8 22 20 5 21 6 23 23 24 12 27 25 24 28 22 5 26 5 24 6 21 20 52 8 19 5 22 11 10 17 13 .
REP AIR P ARTS MODEL 425007x92B 45 F-030721L MOWER HOUSING Key No. Description Part No. Key No. Description Part No. 1 Pulley , Jackshaft 094199 2 Nut, Hex 15x140 3 Belt, Mower Drive 037x88 4 Pulley ,.
REP AIR P ARTS MODEL 425007x92B 46 F-030721L ENGINE MOUNT 1 6 7 8 9 10 11 12 13 14 15 15 21 22 22 23 23 21 29 31 32 34 33 35 2 3 4 5 26.
REP AIR P ARTS MODEL 425007x92B 47 F-030721L ENGINE MOUNT Key No. Description Part No. 1 Fuel Cap ** 092317 2 Fuel T ank 094073 3 Hose Clamp ** 095197 4 Fuel Line (Must cut to length) ** 7601033 5 Hos.
REP AIR P ARTS MODEL 425007x92B 48 F-030721L ELECTRICAL SYSTEM RED RED GREEN GREEN YELLOW YELLOW ORANGE VIOLET BLACK ORANGE DC RED RED BLACK BLACK YELLOW YELLOW ORANGE WHITE ST ARTER ST ART SWITCH S T.
REP AIR P ARTS MODEL 425007x92B 49 F-030721L ELECTRICAL SYSTEM Key No. Description Part No. 1 Harness, Light Wire 250x92 Socket, Light 92372 Bulb, Light 90084 2 Harness, Chassis Wire 250x1 17 3 Switch.
50 F-030721L.
INDEX 51 F-030721L A Adjustments Blade Rotation Control, 22 Clutch, 23 Drive Brake, 23 Mower Housing, Level, 28 Shift Lever , 24 Attachments, 15, 52 B Battery Charge, 24 Check, 12 Clean, 24 Install, 1.
52 F-030721L LA WN TRACT OR ACCESSORIES Make your Lawn T ractor do more than you ever imagined. The accessories shown on this page can be used on your Lawn T ractor .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Murray 425007x92B c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Murray 425007x92B - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Murray 425007x92B, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Murray 425007x92B va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Murray 425007x92B, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Murray 425007x92B.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Murray 425007x92B. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Murray 425007x92B ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
