Manuel d'utilisation / d'entretien du produit 425001x99A du fabricant Murray
Aller à la page of 56
The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT P ARTS and the W ARRANTIES. This information must be included to make sure state laws and other laws are followed.
2 F-050722L T ABLE OF CONTENTS W ARRANTY 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESPONSIBILITY OF THE OWNER 3 . . . . . . . . . . . . . . . . . SAFETY RULES 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
OWNER’S INFORMA TION 3 F-050722L This instruction book is for several different models. The instructions ar e written for a person with some mechanical ability . Like most ser- vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability .
OWNER’S INFORMA TION 4 F-050722L c. Do not turn sharply . Use care when backing. d. Use counterweights or wheel weights when suggested in the Instruction Book. 18. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine.
SAFE MOWING GUIDE 5 F-050722L Each person that operates power equipment must learn to use correct and safe mowing procedures. T o help you learn, carefully read the following pages. Most of the time the operator was not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit.
SAFE MOWING GUIDE 6 F-050722L mower was completely assembled at the store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil.
SAFE MOWING GUIDE 7 F-050722L Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate. If the weather conditions are bad, do not mow .
STEPS T O FOLLOW 8 F-050722L BEFORE MOWING F Be sure to dress correctly . Wear hard shoes, not sandals or tennis shoes. F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade. F Fill the fuel tank outside.
INTERNA TIONAL PICT ORIALS 9 F-050722L INTERNA TIONAL PICT ORIALS IMPORT ANT : Some of the following pic- torials are located on your unit or on literature supplied with the product. Be- fore you operate the unit, learn and un- derstand the purpose for each pictorial.
ASSEMBL Y 10 F-050722L ASSEMBL Y This instruction book is for several models. Some parts or accesso- ries are not included on all models. Read and follow the assembly and adjustment instructions for your mower . All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled.
ASSEMBL Y 11 F-050722L HOW TO INST ALL THE SEA T 1. Carefully remove the plastic bag from the seat. Us e the fasteners shown below to install the seat . The fasteners are shown at full size. (A) 1001054 (B) 17x47 NOTE: Fasteners may be attached to seat for shipping purposes, if so remove fasteners before proceeding.
ASSEMBL Y 12 F-050722L HOW TO ASSEMBLE THE GAUGE WHEELS Use the fasteners shown below to install the gauge wheels . The fasteners are shown at full size. (A) 31x1 1 (B) 17x91 1. Attach the gauge wheels to the axle bolts with the fasteners. NOTE: The axle bolt is mounted in the LOW position.
ASSEMBL Y 13 F-050722L IMPORT ANT! BEFORE YOU ST ART MOWING - Check the engine oil. - Fill the fuel tank with gasoline. - Check the air pressure of the tires. - Check the level of the mower housing. - Make sure the battery cables are attached. - Make sure the wire is attached to the spark plug.
OPERA TION 14 F-050722L Figure 5 Throttle Control Lever Blade Rotation Control Clutch / Brake Pedal Lift Lever Shift Lever LOCA TION OF CONTROLS BLADE RO T A TION CONTROL: Use the blade rotation control to start and stop the rotation of the blade and also to control various accessories, such as a snow thrower .
OPERA TION 15 F-050722L A TT ACHMENTS This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper , a lawn aerator , a hopper spreader or a small trailer . This unit can not use attachments that engage the ground like a plow , a disk harrow , or a cultivator.
OPERA TION 16 F-050722L HOW TO USE THE BLADE ROT A TION CONTROL The blade rotation control is next to the steering wheel (Figure 7). U s e the blade rotation control to engage the blade(s) or to operate a snow thrower attachment. 1. Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position .
OPERA TION 17 F-050722L HOW TO SET THE P ARKING BRAKE 1. Completely push the clutch/brake pedal forward. 2. Lift the parking brake lever (Figure 8). 3. Remove your foot from the clutch/brake pedal and then release the parking brake lever . Make sure the parking brake will hold the unit.
OPERA TION 18 F-050722L HOW TO OPERA TE WITH THE MOWER HOUSING W ARNING: Th e de fle ctor is a safety device. Do not re- move the deflector . The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position.
OPERA TION 19 F-050722L BEFORE ST ARTING THE ENGINE CHECK THE OIL NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer ’ s instructions for the type of gasoline and oil to use.
OPERA TION 20 F-050722L OPERA TING TIPS 1. Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly , the adjustment must be cor- rect. 2. Before you use the unit, check the oil in the engine and add oil if necessary .
MAINTENANCE 21 F-050722L MAINTENANCE CHART FREQUENCY MAINTENANCE REQUIRED COMMENTS Daily or before each use Maintenance engine. Refer to the Engine Owner ’s Manual. Examine blade(s). Check for cracks, wear , and excessive damage. Remove debris from unit and mowing area .
MAINTENANCE 22 F-050722L INSPECT BLADE W ARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.
MAINTENANCE 23 F-050722L HOW TO ADJUST THE BLADE ROT A TION CONTROL W ARNING: T o prevent an injury , the blade rotation control must operate correctly . In normal usage, the blade rotation control will not require an adjustment. However , if the cutting performance decreases or the quality of cut is poor , make the following changes.
MAINTENANCE 24 F-050722L HOW TO CHECK AND ADJUST THE DRIVE BRAKE Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads.
MAINTENANCE 25 F-050722L HOW TO ADJUST THE SHIFT LEVER If the NEUTRAL position on the shift lever does not match neutral on the gearbox, adjust the shift lever as follows. 1. Stop the engine. 2 . Disconnect the adjuster nut from the shifter bracket (Figure 19).
MAINTENANCE 26 F-050722L WHERE TO LUBRICA TE Lubricate the areas shown with engine oil. Apply grease with a brush to the areas shown. Models with grease fittings: Lubricate with grease gun. NOTE: Apply grease to the steering gear assembly . CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit.
W ARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST- MENT position. Level Adjustment Position Figure 23 MAINTENANCE 27 F-050722L HOW TO REMOVE THE MOWER HOUSING 1. Move the blade rotation control to the DISENGAGE position.
MAINTENANCE 28 F-050722L HOW TO ADJUST THE GAUGE WHEELS The axle bolts for the gauge wheels were mounted in the LOW cut position. T o change the position of the gauge wheels, move the axle bolts as follows. IMPORT ANT : Before you adjust the gauge wheels, you must do the following.
MAINTENANCE 29 F-050722L HOW TO LEVEL THE MOWER HOUSING If the mower housing is level, the blade will cut easier and the lawn will look better . W ARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug.
MAINTENANCE 30 F-050722L HOW TO REPLACE THE MOTION DRIVE BEL T REMOV AL 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Completely push the pedal forward and engage the parking brake. 3. Remove the idler pulley (Figure 31).
MAINTENANCE 31 F-050722L INST ALLA TION 1. Slide the motion drive belt between the stack pulley and the belt guides (Figure 34). Install the motion drive belt on the to p pulley of the stack pulley . Make sure the “V” side of the belt is against the pulley .
MAINTENANCE 32 F-050722L HOW TO REPLACE THE MOWER DRIVE BEL T 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 37).
MAINTENANCE 33 F-050722L HOW TO INST ALL THE WHEELS If the wheels must be removed for service, make sure they are installed as follows. Front Wheel 1. Make sure the valve stem is to the outside of the tractor . Slide the front wheel on the spindle (See Figure 38).
MAINTENANCE 34 F-050722L HOW TO REPLACE THE FUSE If the fuse is blown, the engine will not start. The location of the fuse is next to the battery . Remove the fuse and replace with a automotive fuse (Figure 40). Figure 40 Automotive Fuse HOW TO REPLACE THE LIGHT BULB 1.
TROUBLE SHOOTING CHART 35 F-050722L PROBLEM: The engine will not start. 1. Follow the steps, “How T o Start The Engine” in this book. 2. Electric-Start Models: Clean the battery terminals. T ighten the cables. 3. Drain the fuel tank. Clean the fuel line.
F-050722L 36 Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where th e unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone directory .
NOTES 37 F-050722L.
REP AIR P ARTS MODEL 425001x99A 38 F-050722L CHASSIS & HOOD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24 21 22 23 25 26 27 30 29 28 51 31 32 33 34 35 31 36 37 38 16 39 40 41 42 49 16 16 4.
REP AIR P ARTS MODEL 425001x99A 39 F-050722L CHASSIS & HOOD Key No. Part No. Description Key No. Part No. Description 1 690566 Seat 2 028x23 Cap, Push 0n 3 094057 Spring 4 26x229 Screw 5 1001054 B.
REP AIR P ARTS MODEL 425001x99A 40 F-050722L MOTION DRIVE 1 2 3 4 5 6 7 8 9 10 12 11 13 14 15 16 60 18 19 20 17 21 62 55 22 23 25 26 27 28 29 30 31 32 33 35 17 41 62 17 40 39 40 38 45 37 46 49 48 50 5.
REP AIR P ARTS MODEL 425001x99A 41 F-050722L MOTION DRIVE Key No. Part No. Description Key No. Part No. Description 1 009x39 Bolt, Shoulder 2 015x89 Nut, Hex 3 690173 Z Arm, Idler 4 094041 Z Rod, Clut.
REP AIR P ARTS MODEL 425001x99A 42 F-050722L STEERING 1 2 4 5 6 7 8 9 10 11 12 15 6 13 30 30 30 17 18 30 14 30 19 16 26 24 21 22 23 25 27 24 25 22 23 28 29 25 25 30 33 35 36 19 31 31 32 38 20 20 37 40.
REP AIR P ARTS MODEL 425001x99A 43 F-050722L STEERING Key No. Part No. Description Key No. Part No. Description 1 1001980 Wheel, Steering 2 690625 Post, Steering 3 1001982 Cover , Steering Wheel 4 094.
REP AIR P ARTS MODEL 425001x99A 44 F-050722L MOWER HOUSING SUSPENSION 1 2 3 4 5 6 7 8 14 14 9 10 11 12 12 11 13 14 15 16 17 18 19 20 20 21 22 22 23 24 24 24 25 25 11 15 27 26 26 24 25 15 33 34 36 37 3.
REP AIR P ARTS MODEL 425001x99A 45 F-050722L MOWER HOUSING SUSPENSION Key No. Part No. Description Key No. Part No. Description 1 094496 Grip 2 094157 Z Handle, PTO 3 094022 Z Pad, Switch 4 0025x3 Bol.
REP AIR P ARTS MODEL 425001x99A 46 F-050722L MOWER HOUSING 1 2 3 61 2 1 4 5 11 10 47 13 1 4 15 16 17 18 23 22 9 19 8 20 5 21 23 23 24 12 27 25 24 28 22 5 26 5 24 21 20 52 8 19 5 22 11 10 17 13 47 9 14.
REP AIR P ARTS MODEL 425001x99A 47 F-050722L MOWER HOUSING Key No. Part No. Description Key No. Part No. Description 1 094199 Pulley , Jackshaft 2 15x140 Nut, Hex 3 037x88 Belt, Mower Drive 4 690387 P.
REP AIR P ARTS MODEL 425001x99A 48 F-050722L ENGINE MOUNT 1 6 7 8 9 10 11 12 13 14 15 15 21 22 22 21 2 3 4 5 26 30 31 9f 9a 9d 9b 9b 9c 23 23 9e 32 16.
REP AIR P ARTS MODEL 425001x99A 49 F-050722L ENGINE MOUNT Key No. Part No. Description 1 092317 Fuel Cap ** 2 094073 Fuel T ank 3 095197 Hose Clamp ** 4 7601033 Fuel Line (Must cut to length) ** 5 095.
REP AIR P ARTS MODEL 425001x99A 50 F-050722L ELECTRICAL SYSTEM 24x32 94159 24x31 1001993 1002004 21075 94136 GEAR DRIVE TRACTOR * AFTERFIRE SOLENOID OPTIONAL WIRING HARNESS FOR: MAIN HARNESS: 250x138 .
REP AIR P ARTS MODEL 425001x99A 51 F-050722L ELECTRICAL SYSTEM Key No. Part No. Description 1 250x92 Harness, Light Wire 1001716 Socket, Light 090084 Bulb, Light 2 250x138 Harness, Chassis Wire 3 1001.
NOTES 52 F-050722L.
NOTES 53 F-050722L.
54 F-050722L.
INDEX 55 F-050722L A Adjustments Blade Rotation Control, 23 Clutch, 24 Drive Brake, 24 Mower Housing, Level, 29 Shift Lever , 25 Attachments, 15, 56 B Battery Charge, 25 Check, 12 Clean, 25 Install, 1.
56 F-050722L LA WN TRACT OR ACCESSORIES Make your Lawn T ractor do more than you ever imagined. The accessories shown on this page can be used on your Lawn T ractor .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Murray 425001x99A c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Murray 425001x99A - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Murray 425001x99A, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Murray 425001x99A va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Murray 425001x99A, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Murray 425001x99A.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Murray 425001x99A. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Murray 425001x99A ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
