Manuel d'utilisation / d'entretien du produit LT31S du fabricant MTD
Aller à la page of 20
Operator’ s Manual L T31S 2-Cycle Petr ol T rimmer IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y P/N 769-01661 (2/05).
2 INTRODUCTION T ABLE OF CONTENTS Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Assembly Instructions .
3 RULES FOR SAFE OPERA TION SYMBOL MEANING The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
4 RULES FOR SAFE OPERA TION • Add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Remove the fuel cap slowly, and only after the engine stops. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately.
5 SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
6 KNOW YOUR UNIT APPLICA TIONS As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc. KNOW YOUR UNIT Fuel Cap Throttle Control D-Handle Shaft Gri.
7 ASSEMBL Y INSTRUCTIONS Fig. 2 INST ALL AND ADJUST THE D-HANDLE 1. Push the D-handle down onto the shaft housing so that the handle slants towards the shaft grip (Fig. 1). The squared bolt hole in the handle is to the right. 2. Insert the shoulder bolt into the squared hole in the handle and push through.
8 OIL AND PETROL INFORMA TION NOTE: Dispose of the old petrol/oil mix in accordance to Federal, State and Local regulations. OIL AND PETROL MIXING INSTRUCTIONS Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh, clean unleaded petrol.
9 ST ARTING/STOPPING INSTRUCTIONS Fig. 6 Starting Position Start/On (I) Stop/Off (O) Starter Rope Throttle Control Fig. 8 Fig. 7 Blue Choke Lever Position 1 Position 3 Position 2 Primer Bulb Operate this unit only in a well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area.
10 OPERA TING INSTRUCTIONS NOTE: Do not rest the Bump Head™ on the ground while the unit is running. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue .
11 MAINTENANCE AND REP AIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills.
12 MAINTENANCE AND REP AIR INSTRUCTIONS Fig. 19 Fig. 15 NOTE: SplitLine™ can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel. Use Figure 15 to identify the inner reel you have. NOTE: Always use the correct line length when installing trimming line on the unit.
13 MAINTENANCE AND REP AIR INSTRUCTIONS AIR FIL TER MAINTENANCE Removing the Air Filter/Muffler Cover 1. Place the blue choke lever in Position 2 (Fig. 21). NOTE: The blue choke lever must be in Position 2 to remove the air filter/ muffler cover. 2. Remove the four (4) screws securing the air filter/muffler cover (Fig.
14 MAINTENANCE AND REP AIR INSTRUCTIONS CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable through the air filter/muffler cover (Fig. 27). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.
15 MAINTENANCE AND REP AIR INSTRUCTIONS Clean Air Filter The condition of the air filter is important to the operation of the unit. A dirty air filter will restrict air flow and change the air/fuel mixture. This is often mistaken for an out of adjustment carburetor.
16 MAINTENANCE AND REP AIR INSTRUCTIONS CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle.
17 TROUBLESHOOTING If further assistance is requir ed, contact your authorized service dealer . CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting at.
18 SPECIFICA TIONS ENGINE* DRIVE SHAFT and CUTTING A TT ACHMENT* *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Engine Type...........
19 NOTES.
20 NOTES.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté MTD LT31S c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du MTD LT31S - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation MTD LT31S, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le MTD LT31S va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le MTD LT31S, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du MTD LT31S.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le MTD LT31S. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei MTD LT31S ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
