Manuel d'utilisation / d'entretien du produit AIMB-258 du fabricant Arkon
Aller à la page of 84
User Manual AIMB-258 Intel® GM45 µFC-PGA 478 Core TM 2 Duo Mini ITX Motherboard with VGA, DVI, L VDS, 6 COM, Dual GbE, 8 USB, 2 SA T A II, PCIe x 16 V er .
AIMB-258 Us er Manual ii Safety Information Electrical safety ! T o prevent electrical shock hazard, disc onnect the power cable from the electri- cal outlet before relocating the system. ! When adding or removing devices to or fr om the system, ensure that the power cables for the devices are unplugged before the signal cables are connect ed.
iii AIMB-258 User Manual Certifications This device complies with the requirement s in p art 15 of the FCC rules: Operation is subject to the following two conditio ns: ! This device may not cause harmfu l interference, ! This device must accept any interferenc e received, including interference that may cause undesired operation.
AIMB-258 Us er Manual iv T echnical Support If a problem arises with your system and no solution can be obt ained from the user ’s manual, please contact your place of purc hase or local distributor . Alternatively , please try the following help resou rces fo r further guidance.
v AIMB-258 User Manual Content s Chapter 1 Product Introduction ................ ...........1 1.1 Before You Proceed .............. ............. ................ ............. ............. ............. 2 1.2 Motherboard Overview ............. .....
AIMB-258 Us er Manual vi 1.14.17 Serial ATA Connector 1 & 2 (SATA1, SATA 2) .................. ......... 27 1.14.18 PCIe x 16 Slot (PCIE X 16) ............. ................ ................ ............ 28 1.14.19 SPI Flash Connector(SPI_CN1) ...
vii AIMB-258 User Manual B.3 DVI Connector (VGA1B) ....... ............. ................ ............. ............. ........... 64 Table B.3: DVI Connector (VGA1B) ... ................ ................ ........ 64 B.4 RS-232 Serial Port (COM1~COM2) .
AIMB-258 User Manual viii.
Chapter 1 1 Product Introduction This chapter describes the main board features and the new tech- nologies it supports..
AIMB-258 Us er Manual 2 1.1 Before Y ou Proceed T ake note of the following precautions before you inst all motherboard component s or change any motherboard settings. 1.2 Motherboard Overview Before you insta ll the motherboard, study the config uration of your chassis to ensure that the motherboard fit s into it.
3 AIMB-258 User Manual Chapter 1 Product Introduction 1.2.2 Screw Holes Place four (4) screws into the holes indicated by circles to secure the motherboard to the chassis. Caution! Do not over tighten the screws! Doing so ca n damage the motherboard. Place this side t owards the r ear of the chassis.
AIMB-258 Us er Manual 4 1.3 Motherboard Layout Figure 1.1 Motherboard Layout PWR-SW R ESET SPEAKER 1 234 2 4 68 13 57 1 2 345.
5 AIMB-258 User Manual Chapter 1 Product Introduction 1.4 S pecifications Processor Sys- tem CPU (45 nm µFC-PGA 478) Intel ® Core™2 Duo Intel Celeron M Max.
AIMB-258 Us er Manual 6 *Dual Display Clone uses both display pipes to drive the same content at th e same resolution and color depth to t wo different displays.
7 AIMB-258 User Manual Chapter 1 Product Introduction 1.6 Board Diagram Int el G M45 n GMCH CRT BIOS NXP 955 5 16-bit GP I O Super IO Win bon d W83627UHG Dir ec t M e d i a In ter fa ce 2G B / s b a n.
AIMB-258 Us er Manual 8 1.7 Ordering Information 1.8 Riser Card 1.9 Bracket V iew 1.10 Accessories Part Number Display GbE SA T A Serial CF AIMB-258G2-00A1E VGA/ DVI/ L VDS Dual 2 6 1 Part Number Description AIMB-R430P-03A1E 2U riser ca rd with 3 PCI slot expansion Part Number Description 1700003195 USB cable with fou r ports, 1 7.
9 AIMB-258 User Manual Chapter 1 Product Introduction 1.1 1 Layout Content List T able 1.1: Jumper Setting List Label Function JSETCOM1 COM1/+5 V/+12 V Selection JSETCOM2 COM2 RS232/422/485 Mo de Selection CMOS1 Clear CMOS J1 LCD Power 3.
AIMB-258 Us er Manual 10 T able 1.4: CMOS1: Clear CMOS Pins Result 1-2* Keep CMOS dat a* 2-3 Clear CMOS data *Default T able 1.5: J1:LCD Power 3.3 V/5.5 V Selection Closed Pins Result 1-2* 3.3 V* 2-3 5 V *Default T able 1.6: PSON1: A TX, A T Mode Selection Closed Pins Result 1-2 A T Mode 2-3* A TX Mode* *Default T able 1.
11 AIMB-258 User Manual Chapter 1 Product Introduction 1.12 Central Processing Unit (CPU) for AIMB-258 The motherboard AIMB-258 comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket designed for the Intel® Pen tium® M / Celeron® M processor (Supports mPGA478M, Micro-FCPGA).
AIMB-258 Us er Manual 12 1.12.1 Inst alling the CPU Caution! ! Intel® socket 478 Pentium M/ Celeron M CPU with 90nm process package shou ld come with installatio n instructions for the CPU, heatsink, and the ret ention mechanism. If the instructions in this section do not match the CPU document ation, follow the la tter .
13 AIMB-258 User Manual Chapter 1 Product Introduction 2. The processor socket comes with a screw to secure the processor , please unlock the screw first. 3. Position the CPU above the socket and the gold triangula r mark on the CPU must align with pin 1 of the CPU socket.
AIMB-258 Us er Manual 14 1.12.2 Inst alling the CPU Heat sink and Fan The Intel® Pentium® M / Celeron® M processor (support s mPGA478M, Micro- FCPGA) requires a specially designed heatsink and fan assembly to ensure optimu m thermal condition and performance.
15 AIMB-258 User Manual Chapter 1 Product Introduction Caution! ! Do not forget to connect the fan cables to the fan connectors. Insuf- ficient air flow inside the system may damage the mothe rboard components, and hardware monitoring errors can occur if you fail to plug this connector .
AIMB-258 Us er Manual 16 1.12.3 Uninst alling the CPU Heat sink and Fan 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each scre w counter- clock- wise. 3. Carefully remove the heats ink and fan assembly from t he mother- board.
17 AIMB-258 User Manual Chapter 1 Product Introduction 1.13 System Memory 1.13.1 DIMM Socket s Location The motherboard comes with two 204-pin Double Dat a Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) sockets. The following figure illustrate s the location of the sockets: 1.
AIMB-258 Us er Manual 18 1.13.3 Memory Support List T able 1.9: SODIMM DDR3 SODIMM DDR3 Brand Size Speed T ype ECC V endor PN Advantech PN Memory T ranscend 1GB DDR3 1066 SODIMM DDR3 NT S 1 2 8 M S K .
19 AIMB-258 User Manual Chapter 1 Product Introduction 1.14 Connectors 1.14.1 Rear Panel Connectors T able 1.10: Rear Panel Connectors No. Label Function Description 1 KBMS1 PS/2 mouse connector The stan dard PS/2 mouse DIN connec- tor is for a PS/2 mouse.
AIMB-258 Us er Manual 20 1.14.2 CPU Fan Connector (CPUF AN1) Caution! ! Do not forget to connect the fan cables to the fan connectors. Insuf- ficient air flow inside the system may damage th e motherboard components, and hardware monitoring errors can occur if you fail to plug this connector .
21 AIMB-258 User Manual Chapter 1 Product Introduction 1.14.3 System Fan Connector (SYSF AN1, SYSF AN2) Caution! ! Do not forget to connect the fan cables to the fan connectors. Insuf- ficient air flow inside the system may damage the mothe rboard components, and hardware monitoring errors can occur if you fail to plug this connector .
AIMB-258 Us er Manual 22 1.14.4 Serial Port Connector 3456 (COM3456) 1.14.5 Front Head phone Connector (HD1) This connector is for a chassis-mounted fr ont p anel audio I/O module that support s either HD Audio. Connect one end of the fr ont p anel audio I/O module cab le to this connector .
23 AIMB-258 User Manual Chapter 1 Product Introduction 1.14.6 Front Panel Connector (JFP1/JFP2/JFP3 ) There are several external switches to monitor and control the AIMB-258.
AIMB-258 Us er Manual 24 1.14.1 1 Power LED and keyboard lock connector (JFP3 / PWR_LED&KEY LOCK) (JFP3 / PWR_LED&KEY LOCK) is a 5-pin connector for the power on LED and Key Lock function. Refer to Appendix B for det ailed information on the pin assignments.
25 AIMB-258 User Manual Chapter 1 Product Introduction 1.14.13 A TX Power Connector (A TX1) This connector is for an A TX Micro-Fit po wer supply . The plugs from the power sup- ply are designed to fit these connectors in only one orientation. Find th e proper orien- tation and push do wn firmly unti l the connectors completely fit.
AIMB-258 Us er Manual 26 1.14.14 LCD Inverter Connector (VP1) 1.14.15 L VDS Connector (L VDS1) VDDSAFE_1 VDDSAFE_2 GND_1 GND_7 VDDSAFE_3 VDDSAFE_4 OD0- ED0- OD0+ ED0+ GND_2 GND_8 OD1- OD1+ ED1- ED1+ G.
27 AIMB-258 User Manual Chapter 1 Product Introduction 1.14.16 Digit al I/O Connector (DIO_CN1) 1.14.17 Serial A T A Connector 1 & 2 (SA T A1, SA T A2) SA T A1 SA T A2 Note! AIMB-258 features a high performance serial ATA int erface (up to 300 MB/s) which eases cabling to hard drives with thin and long cables.
AIMB-258 Us er Manual 28 1.14.18 PCIe x 16 Slot (PCIE X 16) 1.14.19 SPI Flash Connector(SPI_CN1) Note! This connector is for factory use only..
29 AIMB-258 User Manual Chapter 1 Product Introduction 1.14.20 Memory Connector Channel A/B(DIMM1/2) 1.14.21 SPDIF1 out connector(SPDIF1) 1 2 4 3.
AIMB-258 Us er Manual 30 1.14.22 CF connector.
Chapter 2 2 BIOS Operation.
AIMB-258 Us er Manual 32 2.1 BIOS Introduction Advantech provides full-featured A wardBIO Ses, which deliver the superior perfor- mance, compatibility , and functionality that today’s manufacturers of industrial PCs and embedded boards demand.
33 AIMB-258 User Manual Chapter 2 BIOS Operation 2.2.1 Main Menu Press <Del> to enter A wardBIOS CMOS Se tup Utility , the Main Menu will appear on the screen. Use arrow keys to select am ong the items and press <Enter> to accept or enter the sub-menu.
AIMB-258 Us er Manual 34 2.2.2 S t andard CMOS Features ! Date The date format is <weekday>, <month>, <day>, <year>. ! Tim e The times format in <hour> <minute> <second>, based on the 2 4-hour time ! IDE Channel 0/1/2, Master IDE HDD Auto-Detection Press "Enter" for automatic device detection.
35 AIMB-258 User Manual Chapter 2 BIOS Operation 2.2.3 Advanced BIOS Features ! CPU Feature This item allows user to adjust CPU features, CPU ratio, VID a nd thermal and special feature like XD flag. ! Hard Disk Boot Priority This item allows user to select bo ot se quence for system device HDD, SCSI, RAID.
AIMB-258 Us er Manual 36 – T ypematic Rate (Chars/Sec) This item controls the speed at wh ich the system registers repe ated key- strokes. The eight setting s are 6, 8, 10, 12, 15, 20, 24 and 30. – T ypematic Delay (Msec) This item sets the keypress delay be fore typematic repetition kicks in.
37 AIMB-258 User Manual Chapter 2 BIOS Operation ! PEG Force x1 Enabled or Disabled. ! On-Chip Frame Buffer Size The On-Chip Frame Buf fer Size can be set to 1 MB or 8 MB.
AIMB-258 Us er Manual 38 ! Onboard Device This item enables users to set the Onbo ard device st atus; it includes enable LAN1 and LAN2 devices. ! Super IO Device This item enables users to set the Super IO device st atus; it includes enabling COM1~COM6 .
39 AIMB-258 User Manual Chapter 2 BIOS Operation ! Onboard Serial port 1 [3F8 / IRQ4] This item allows user to adjust serial p ort 1 address and IRQ. ! Onboard Serial port 2 [2F8 / IRQ3] This item allows user to adjust serial p ort 2 address and IRQ.
AIMB-258 Us er Manual 40 2.2.7 Power Management Setup ! PCI Express PM Function This allows you to enable or disable system wake u p via PCI Express PME (Power Management Event). ! Power-Supply T ype [A TX] This item allows user to set power-supply type, A TX or A T mode.
41 AIMB-258 User Manual Chapter 2 BIOS Operation ! Power Management [User Defined] This item allows user to select system po wer saving mode. ! Video Off Method [DPMS] This item allows user to determine the manner is which the monitor is blanked.
AIMB-258 Us er Manual 42 2.2.8 PnP/PCI Configurations ! Reset Configuration Dat a [Disabled] The default is Disabled. Sele ct Enabled to reset Extend ed System Configuration Data (ESCD) if yo u have installed a new ad d-on card, and system configur ation is in such a state t hat the OS cannot boot, enable this.
43 AIMB-258 User Manual Chapter 2 BIOS Operation ! CPU W arning T emperature The system will give an automatic warning if the CPU temp erature goes over the selected setting. ! Current System T emperature This shows you the current temperature of system.
AIMB-258 Us er Manual 44 T o Est ablish Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password”, enter the desired p assword and press <Enter>. 3. At the “Confirm Password” prompt, retype the desired p assword, then press <Enter>.
Chapter 3 3 Chipset Software Install Utility.
AIMB-258 Us er Manual 46 3.1 Before you Begin T o facilitate the installation of the enhanc ed display device drivers and utility soft- ware, you should read th e instructions in this chapter carefully before you begin. The device drivers for the AIMB-258 board are located on the so ftware installation CD.
47 AIMB-258 User Manual Chapter 3 Chipset Software Install Utility 3.3 Windows V ist a/XP Driver Setup Insert the driver CD into your syste m's CD-ROM drive. Y ou can see the driver folders items. Move the mouse cursor over the fold er "Drv_INF".
AIMB-258 Us er Manual 48.
Chapter 4 4 VGA Setup.
AIMB-258 Us er Manual 50 4.1 Introduction The Intel GM45 int egrated graphics controller provides an analog display po rt. Y ou need to install the VGA driver to enable the function. Intel Graphics Media Accelerator 4500MHD: Incorporat ing the latest Microsoft* DirectX*10 support capabilities a nd Shader Model 4.
Chapter 5 5 LAN Configuration.
AIMB-258 Us er Manual 52 5.1 Introduction The AIMB-258 features single/dual Gigab it Ethernet network interface. With the Realtek R TL81 1 1C GbE controller designed-in, AIMB-258 implement s the PCI Express host interface (PCI-E X1 ) in LAN connection with the maximum through put of 2Gbps for he avy-duty industrial network ap plication.
53 AIMB-258 User Manual Chapter 5 LAN Configuration Select the subdirectory based OS version; inst all the appropriate LAN driver ..
AIMB-258 Us er Manual 54.
Appendix A A Programming the Watchdog Timer.
AIMB-258 Us er Manual 56 A.1 Programming the W atchdog Timer The AIMB-258's watchdo g timer can be used to monitor system sof tware operation and take corrective action if the sof tware fails to function after the programmed period. This section describes the ope ration of the watchdog timer and how to pro- gram it.
57 AIMB-258 User Manual Appendix A Programming the Watchdog Timer.
AIMB-258 Us er Manual 58 T able A.1: Watch dog T imer Registers Address of register (2E) Attr ibute Read/W rite V alue (2F) and description 87 (hex) - W rite this address to I/O addr ess port 2E (hex) twice to unlock the W83627UHG 07 (hex) write Write 08 (hex) to select register of watchdog t imer .
59 AIMB-258 User Manual Appendix A Programming the Watchdog Timer A.1.3 Example Program 1. Enable watchdog timer and set 10 sec. as timeout interval ;--------------------------------------------------.
AIMB-258 Us er Manual 60 ;----------------------------------------------------------- Mov al,07h ; Select registers of wat chdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;--------------------------.
61 AIMB-258 User Manual Appendix A Programming the Watchdog Timer Dec dx ; Enable the function of watch dog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;------------------------------------.
AIMB-258 Us er Manual 62 ;----------------------------------------------------------- Dec dx ; lock W83627UHG Mov al,0aah Out dx,al 5. Generate a time-out signa l without timer counting ;-------------.
Appendix B B Pin Assignments.
AIMB-258 Us er Manual 64 B.1 USB Connector (USB56,USB78) B.2 VGA Connector (VGA1A) B.3 DVI Connector (VGA1B) T able B.1: USB5/USB 6 Connector (USB56) Pin USB1 Signal Pin USB2 Signal 1+ 5 V 2+ 5 V 3 LP5- 4 LP5+ 5 LP5+ 6 LP5- 7 GND 8 GND 9N C 1 0 G N D 75 3 1 1 0 864 2 T able B.
65 AIMB-258 User Manual Appendix B Pin Assignments B.4 RS-232 Serial Port (COM1~COM2) 6G N D 1 6 G N D 7G N D 1 7 G N D 8G N D 9+ 5 V _ V G A 10 GND T able B.
AIMB-258 Us er Manual 66 B.5 RS-232 Serial Port (COM3 ~ COM6) T able B.5: RS-232 Se rial Port (COM23) Pin Signal Pin Signal 1 COM3_#DCD 2 COM3_#DSR 3 COM3_SIN 4 COM3_#RTS 5 COM3_SOUT 6 COM3_#CTS 7 COM.
67 AIMB-258 User Manual Appendix B Pin Assignments B.6 PS/2 Keyboard/ Mouse Connector (KBMS1) B.7 CPU Fan Power Connector (CPUF AN1) T able B.6: PS/2 Keyboard/ Mou se Connector (KBMS1) Pin Signal Pin Signal 1 KB DA T A 2 NC 7M S D A T A 6N C 3G N D 8N C 4V C C 9G N D 5 KB CLOCK 10 VCC 1 1 MS CLOCK 12 NC 12 11 10 9 87 5 3 1 2 4 6 T able B.
AIMB-258 Us er Manual 68 B.8 Power LED & Keyboard Lock Connector (JFP3) Y ou can use an LED to indicate when the single board computer is on. Pin 1 of JFP3 supplies the LED's power , and Pin 3 is the ground. B.9 HDD LED and External S peaker Connector(JFP2/HDD LED and SPEAKER) The single board computer has its own buzzer .
69 AIMB-258 User Manual Appendix B Pin Assignments B.10 A TX Sof t Power Switch and Reset Connector (JFP1/ PWR-SW and RESET) B.1 1 Audio Front Panel Connector (FP AUD1) T able B.10: Audio Front Pane l Connector (JFP1/ RESET) Pin Signal 1P W R _ B T N # 2G N D 3 RESET 4G N D 1 2 4 3 T able B.
AIMB-258 Us er Manual 70 B.12 GPIO Pin Header (GPIO1) T able B.12: GPIO Pin Header (GPIO1) Pin Signal Pin Signal 1 DIO_GP20 2 DIO_GP10 3 DIO_GP21 4 DIO_GP1 1 5 DIO_GP22 6 DIO_GP12 7 DIO_GP23 8 DIO_GP1.
71 AIMB-258 User Manual Appendix B Pin Assignments B.13 L VDS Connector (L VDS1) T able B.13: L VDS Connector (L VDS1) Pin Signal Pin Signal 1 VDDSAFE_1 2 VDDSAFE_2 3 GND_1 4 G ND_7 5 VDDSAFE_3 6 VDDS.
AIMB-258 Us er Manual 72 B.14 L VDS Power Jumper (J1) *default setting B.15 L VDS Invert (VP1) T able B.14: L VDS Power Jumper (J1) Pin Signal 1 VCC3 2 VDD_LCD 3V C C 3 1 2 3 1 2 *3.
73 AIMB-258 User Manual Appendix B Pin Assignments B.16 System I/O Port s B.17 DMA Channel Assignment s T able B.16: System I/O Po rt s Addr . range (Hex) Device 000-01F DMA controller 020-021 Interru.
AIMB-258 Us er Manual 74 B.18 Interrupt Assignment s B.19 1st MB Memory Map T able B.18: Interrup t Assignment s Priority Interrupt# Interrupt Source 1 NMI Parity error detected 2 IRQ0 Interval timer .
75 AIMB-258 User Manual Appendix B Pin Assignments.
www .advantech.com Please verify specifications be fore quoting. This guide is intended for reference purposes only . All product specifications are subj ect to change without notice.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Arkon AIMB-258 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Arkon AIMB-258 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Arkon AIMB-258, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Arkon AIMB-258 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Arkon AIMB-258, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Arkon AIMB-258.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Arkon AIMB-258. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Arkon AIMB-258 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
