Manuel d'utilisation / d'entretien du produit HS-HD1100U du fabricant Mitsubishi
Aller à la page of 64
VIDEO CASSETTE RECORDER OWNER’S GUIDE MODEL HS-HD1 100U This Video Cassette Recorder is based on the D-VHS and VHS formats. Only video cassette tapes with the mark or the mark may be used with this model. However, D-VHS recordings are possible only with cassettes marked .
♦ High-Definition Digital Recording and Playback ♦ IEEE 1394 Interface for Digital Home Networking ♦ Rew/FF at 500X speed (:43 seconds for a T -120 tape) ♦ S-VHS quasi playback ♦ PerfecT ape ® CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
1 To connect your VCR, go to page 4. To play a tape , go to page 1 1. To record a program , go to page 20. T o learn about Advanced Features , go to page 42. SHORTCUTS IMPORT ANT SAFEGUARDS ...................... 2 Hooking Up Y our VCR ...............
2 IMPORT ANT SAFEGUARDS Please read all these instructions carefully regarding your VCR before you begin operating it. Follow all warnings and instructions marked on the VCR. Thank you. 1 Read Instructions All the safety and operating in- structions should be read before the product is operated.
3 16 Power Lines An outside antenna system should not be located in the vi- cinity of overhead power lines or other electric light or power cir- cuits, or where it can fall into such power lines or circuits.
4 Hooking Up Y our VCR Unpacking Y our VCR As you unpack your new VCR, please make sure the following items are included: IMPORT ANT Never place any heavy objects on top of the VCR. Use caution when placing the VCR on top of the television as the surface may not be stable.
5 IMPORT ANT Y ou must use one of the connections shown on page 5 and 6 in order to record television or cable programs. Hooking Up Y our VCR VHF UHF VHF/UHF ANTENNA OUT IN x x x x VCR Rear Panel TV R.
6 Connecting Cable and Cable Box, if only some channels are scrambled 1 Y ou will need a cable splitter , five lengths of coaxial cable, and a cable A/B switch. 2 Connect cable from wall outlet to IN terminal on the cable splitter . 3 Connect the coaxial cable to OUT terminal on the cable splitter and A-IN on the A/B switch.
7 IMPORT ANT Y our TV Owner ’s Guide may have additional suggestions for audio video hookups. T o connect your VCR to a mono (non-stereo) TV , connect only the white AUDIO OUT L of the VCR and the white AUDIO INPUT of the TV . Since the TV is not stereo, you cannot take advantage of your VCR’ s Hi-Fi stereo sound.
8 Hooking Up Y our VCR Connections to Integrated HDTV or IEEE 1394-equipped HDTV Receiver If you connect the HS-HD1 100U to an integrated HDTV or an IEEE 1394-equipped HDTV receiver with an IEEE 1394 .
9 Hooking Up Y our VCR Notes about IEEE 1394 network The IEEE 1394-equipped devices that are available to be connected to the HS-HD1 100U are an integrated HDTV , an IEEE 1394-equipped HDTV receiver or another D-VHS VCR .
10 Connections to Home Theater Receiver Y ou may wish to connect your VCR to a Home Theater Receiver so that you can take advantage of the Surround Sound audio recordings that are common with many movies. Home Theater Receivers will often control both the sound that is heard from the speakers and the picture shown on your TV .
11 Playback Setting Up Y our VCR to Playback/Recording the Digital Broadcast in D-VHS (digital) Format 1 Make sure that your VCR and the integrated HDTV or the IEEE 1394-equipped HDTV receiver is connected with an IEEE 1394 cable. 2 T urn on the IEEE 1394-equipped HDTV receiver .
12 3 Y ou are now watching the VCR’ s picture. T o go back to viewing the picture from the TV , press the TV’ s INPUT button to go back to the previous ANTENNA input position. 4 Later , you should turn the RF converter OFF by following instructions on page 48.
13 Loading a T ape T apes can be loaded into your VCR as long as the VCR is plugged in. Even when the VCR POWER is of f, loading a tape will automatically turn the VCR on. Use only tapes that have a , or label. 1 Hold the tape so that the long narrow edge with the contents label faces you.
14 Using Basic Playback Controls Rewinding a T ape While the tape is stopped, press REW on the remote control or turn the shuttle ring on the front panel to the left. Fast Forwarding a T ape While the tape is stopped, press FF on the remote control or turn the shuttle ring on the front panel to the right.
15 Y our VCR comes with Mitsubishi’s exclusive on-screen operating system. This system has been developed to simplify the operation of your VCR with clear , easy-to-understand language and design.
16 Adding and Deleting Channels If necessary , you can manually add or delete channels after you have completed the automatic channel memorization. 1 Make sure that video mute is ON.
17 Setting the Clock Y ou have to set the clock using either Setting the Auto Clock or Setting the Clock Manually . Setting the Auto Clock Y our VCR can set the clock automatically by picking up a time signal which some TV and cable channels transmit with their broadcasts.
18 If the VCR displays the wrong time 1 Follow the procedure on the previous page to step 3 . Press ENTER. 2 Y ou will see the Set the clock menu. Channel will be highlighted. If you know the channel that carries a time signal, press the ADJUST buttons to enter the channel.
19 5 Press the ADJUST buttons until the correct month appears on screen. Press ENTER. 6 Press the ADJUST buttons to set the current year . Press ENTER. 7 Press the ADJUST buttons to set the date. Press ENTER. 8 The hour numbers and the am/pm indicator will be blinking.
20 Y our new VCR of fers a wide variety of recording options that take full advantage of our advanced electronics. First, you can learn how to record a current broadcast. Then, in another section of this book called Timer Recording , you can learn how to program your VCR to record at a later time and day .
21 Recording recording copy protected digital programs Some programs have copy protect data to prohibit or restrict recording. • Programs without copy protection : D-VHS recording is available. • Programs with copy restriction : Y ou can record in D-VHS format once, but cannot copy .
22 Recording a Current Broadcast in VHS (analog) Format 1 Load a tape with its erasure prevention tab intact into the VCR. 2 Select the speed at which you would like to record by pressing SP/EP on the remote control or on the front panel.
23 Using One-T ouch Recording (OTR) One-T ouch Recording (OTR) is a way to begin recording immediately and have your VCR stop recording and turn off automatically after your show is over . 1 When you record a digital broadcast in D-VHS (digital) format, follow the steps 1 to 4 on page 20.
24 Using Standby One-T ouch Recording (OTR 2 ) Standby One-T ouch Recording (also called OTR 2 ) is a programming method to begin recording within the next 24 hours and record in 30 minutes intervals. Before you use OTR 2 , make sure the clock has been set correctly .
25 Notes about A vailable T ape and Recording Time Recording Format The available recording format is as follows: When you use a D-VHS tape for D-VHS recording, the recording format is preset to D-VHS format. Recording Mode The available recording mode is as follows: HS (high speed) : Y ou can record the half duration of STD.
26 Using Audio and V ideo Functions The audio and video function menus allow you to set things such as listening to the stereo track of your recording, or setting the tape length to have the remaining time display function work properly . The VCR will display the functions and settings on your TV screen.
27 Descriptions of V ideo Functions T ape (T ape) Adjust this function to ensure the accuracy of the Remaining Time display . The remaining time function does not work properly with a tape that is less than 30 minutes long.
28 Mitsubishi offers 5 ways to set your VCR to record upcoming broadcasts. Choose from: D-VHS (digital) T imer Recording VHS (analog) Timer Recording of Digital Broadcast VCR Plus+ system programming .
29 When you program both the D-VHS (digital) and VHS (analog) timer recording When you turn the VCR off, the programmed recording light will appear on the front panel display , showing that the VCR is in stand-by mode for the VHS timer recording.
30 6 Day will flash. Press the ADJUST buttons to choose the day on which you want to record; for example, Monday the 1 1th. Y our choices are: • a single day up to one month away . • every day from Monday through Friday; for example, to tape a soap opera.
31 ¬Program to record ƒChannel 2 ƒDay Monday 11 ƒStart time 11:30am ƒStop time 1:30pm ƒRecord speed SP ∫πMENU to go back ∂ ππADJUST to select ≤¥≥πENTER to en.
32 IMPORT ANT If you press ENTER when you set the timer recording incompletely , Current Program is not completed will appear on your screen. If two programmed recording times overlap, VCR is already programmed for that time will display on your screen for about 3 seconds, and then the Recap screen will appear .
33 T imer Recording VCR Plus+ ® System Programming The VCR Plus+ system allows you to program your VCR to record by simply entering a PlusCode programming number . Y ou can find this number in TV Guide or possibly your local TV listings. 1 Load a tape with its erasure prevention tab intact into the VCR.
34 7 If you wish to change the record speed, press ENTER repeatedly until the record speed is flashing. Change the recording speed by pressing the ADJUST buttons. Press ENTER. 8 T o program additional recording times, select an empty program line by pressing the ADJUST buttons.
35 T imer Recording Hints T o use the VCR before timer recording begins, press POWER on the remote once. This turns the programmed recording light of f and the VCR on. If you use POWER on the front panel for this purpose, press it twice. Pressing it once turns of f the programmed recording light; pressing it again turns the VCR on.
36 Program Caution If your VCR is set to record in VHS format, but the power is still ON within 3 minutes before timer recording starts, this screen will appear to remind you to turn of f the VCR. If the VCR is still turned on 12 seconds before the start time of the recording, that timer recording will be cancelled.
37 Cancelling a T imer Recording before the Recording Starts 1 Press MENU on the remote control. Y our VCR will turn on and VCR Main Menu will appear on your screen. Press the ADJUST buttons on the remote control to select Program to record . Press ENTER.
38 Editing Features IEEE 1394 INTERFACE HS-HD1100U ANOTHER D-VHS VCR IEEE 1394 INTERFACE IEEE 1394 INTERFACE 1 Connect an IEEE 1394 cable to IEEE 1394 INTERF ACE on the playback VCR and to IEEE 1394 INTERF ACE on the HS-HD1 100U. Y ou can use either of the two IEEE 1394 INTERF ACE terminals.
39 Editing Features IEEE 1394-equipped HDTV receiver integrated HDTV OR IEEE 1394 INTERFACE HS-HD1100U PLAYBACK RECORDING VCR IEEE 1394 INTERFACE IEEE 1394 INTERFACE L R L AUDIO OUT L AUDIO OUT R AUDIO IN R AUDIO IN L VIDEO IN S-VIDEO IN VIDEO OUT S-VIDEO OUT R Use either a video cable or an S-video cable.
40 Copying a T ape from Analog to Analog There are two basic ways to make a copy of a tape from analog to analog. One way is to use the HS-HD1 100U to record and another VCR for playback. The other way is to use another VCR to record and use the HS-HD1 100U for playback.
41 Editing Features R AUDIO VIDEO OUT OUT L R L R L RECORDING AUDIO OUT L AUDIO OUT R AUDIO IN R AUDIO IN L VIDEO IN VIDEO OUT HS-HD1100U PLAYBACK Using the HS-HD1 100U to Playback to Another VCR 1 Connect one stereo audio cable to AUDIO IN L and R on the recording VCR, and to AUDIO OUT L and R on the HS-HD1 100U.
42 Advanced Features Advanced Playback Controls (for analog playback only) Special Effects Y ou can use the shuttle ring and the jog dial on the front panel, or ^ I and I on the remote to control the playback speed of the tape. Change the playback speed while tape is paused 1 While the VCR is playing a tape, press P AUSE to freeze the picture.
43 Adjusting the T racking automatic tracking Y our VCR automatically adjusts the tape to give you the best quality picture. When you start playback of a newly inserted tape, the DIGIT AL TRACKING light (D) will flash, showing that the VCR is adjusting the picture.
44 Quick search (CM skip) Quick search lets you skip over the tape you are playing in about 30 second intervals. It is designed so that you can quickly speed through any commercials you may have recorded. T o do this: 1 Make sure that you have set the VCR/TV slide switch on the remote control to the VCR position.
45 Counter zero stop Counter zero stop allows you to quickly access the beginning of a recorded or playback section of a tape. The counter zero stop will automatically fast forward or rewind the tape to “0H00M00S” and stop. 1 Press CANCEL on the remote control at the point you wish to locate later .
46 repeat playback Y ou can playback a section of tape over and over using repeat playback. The tape will play until the next index mark, rewind to the previous index mark and resume playing. If there is only one index mark on the tape, then the VCR will play or rewind to that mark and resume playback.
47 IMPORT ANT The time gauge and remaining time work by detecting control signals on recorded tapes. Therefore, they do not function while playing blank tapes.
48 Auto power save (auto-off) When the Auto Power Save feature is turned on, the VCR will automatically turn off after remaining idle for 30 minutes. If a control, such as a menu function or channel selection is used or if there is a tape playing or being recorded, the VCR will remain on.
49 The VCR will display the testing status screen. When testing, the VCR records for one second, then evaluates the recording it made. The entire test takes about 8 seconds. During this time, the PT light on the front panel will flash. If you wish to cancel the test, press ST OP on the remote while the PT light is still flashing.
50 Advanced Options Using the remote control to operate your TV The HS-HD1 100U remote control can operate many of the frequently-used functions of your TV . Y ou only need one remote to operate both your VCR and TV . The HS-HD1 100U remote control is pre-set to operate Mitsubishi televisions, but it can also operate TVs from other manufacturers.
51 T o program the remote control operational setting The HS-HD1 100U has two remote control operational settings, VCR-A and VCR-B. These are available so you may separately control two Mitsubishi VCRs that are placed close together . The VCR-A setting can be used to operate any other Mitsubishi VCR introduced since 1986.
52 Location of Controls Remote Control VCR POWER Turns the VCR On or Of f. If you have programmed the VCR to record, you need to turn the VCR of f. EJECT Ejects a tape. CHANNEL Up and Down Selects next higher or lower channel in the VCR’s or TV’ s channel memory .
53 JOG/CHANNEL Changes channels when tape is stopped. Adjusts tracking and picture vibration. SHUTTLE ring Fast forwards a tape or fast forward searches by turning right. Rewinds a tape or reverse searches by turning left. IEEE 1394 INPUT Selects an integrated HDTV , an IEEE 1394-equipped HDTV receiver or a D-VHS VCR connected to the VCR.
54 Location of Controls PerfecT ape ® light : PT Flashes when PerfecT ape test is in progress. Stays lit when test is complete. D-VHS indicator : Lights up when D-VHS playing/recording. play and record lights : PLAY REC These light up when the VCR is playing a tape or recording.
55 Location of Controls IEEE 1394 INTERFACE ANTENNA OUT IN TIMER RESET IN 1 AUDIO VIDEO OUT IN 1 OUT L L/MONO RR Rear Panel Jacks VIDEO INput and OUTput jacks Y ellow jacks are for receiving (IN) and sending (OUT) video signals to a monitor TV or from another VCR.
56 Important Information Special Information Concerning Stationary Images or Letterbox Images: For best performance and longest life, the normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should fill the screen with constantly moving images rather than stationary images or patterns.
57 T rouble Checks If your VCR malfunctions, try the following steps prior to contacting your Mitsubishi Dealer: 1 Check the T rouble Checks below to see if there is a solution to the current problem that you are experiencing.
58 T rouble Checks T ry This... • Try automatic head cleaning. • Clean the video heads using a dry-type video head cleaning cassette. Do not use a wet-type head cleaning cassette, as it may damage your VCR. Excessive use of a cleaning cassette could shorten head life.
59 Specifications F ORMA T VHS NTSC standard with Hi-Fi audio and D-VHS standard V IDEO S IGNAL S YSTEM EIA standard; NTSC color R ECORD /P LA YBACK S YSTEM V ideo -- 4 heads Audio -- 2 Hi-Fi channels.
60 D daylight savings time ................... 18 digital tracking light ...................... 54 display button .............................. 52 displaying current time ................ 47 displaying time gauge ................. 46 D-VHS button ...
RET AIN THIS PORTION FOR YOUR RECORDS SERIAL NO. CUST OMER NAME STREET ADDRESS CITY ST A TE ZIP PHONE ( ) PURCHASE DA TE / / MO DA Y YR PLACE OF PURCHASE PHONE ( ) W arranty MITSUBISHI VIDEO CASSETTE RECORDER LIMITED W ARRANTY MITSUBISHI DIGIT AL ELECTRONICS AMERICA, INC.
MITSUBISHI DIGIT AL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road Irvine, CA 92618-1904 www .mitsubishi-tv .com © 2002 Mitsubishi Digital Electronics America, Inc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Mitsubishi HS-HD1100U c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Mitsubishi HS-HD1100U - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Mitsubishi HS-HD1100U, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Mitsubishi HS-HD1100U va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Mitsubishi HS-HD1100U, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Mitsubishi HS-HD1100U.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Mitsubishi HS-HD1100U. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Mitsubishi HS-HD1100U ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
