Manuel d'utilisation / d'entretien du produit LDT651P du fabricant Mitsubishi Electronics
Aller à la page of 40
OPERA TION MANUAL.
DECLARA TION OF CONFORMITY This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1 E IMPORT ANT INFORMA TION W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT T O RAIN OR MOISTURE. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE P ARTS INSIDE.
2 E • When operating the LCD monitor with an AC 100-120V power supply in North America, use a power supply cord provided with this monitor . • When operating the LCD monitor with an AC 220-240V power supply in Europe, use a power supply cord provided with this monitor .
3 E Thank you for your purchase of a MITSUBISHI LCD product. T o ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.
4 E SAFETY PRECAUTIONS (Continued) 15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts speci fi ed by the manufacturer , or those with the same characteristics and performance as the original parts.
5 E - The TFT colour LCD panel used in this monitor is made with the application of high precision technology . However , there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colours or brightness.
6 E Contents Introduction IMPORT ANT INFORMA TION ............................................ 1 DEAR MITSUBISHI CUSTOMER ..................................... 3 SAFETY PRECAUTIONS .................................................. 3 TIPS AND SAFETY INSTRUCTIONS .
7 E Supplied Accessories If any component should be missing, please contact your dealer . Liquid Crystal Display: 1 Remote control unit: 1 Power cord: 1 R-6 battery: 2 CD-ROM (Util.
8 E Part Names n Rear view 12 7 5 3 1 8 11 14 16 15 13 10 6 4 2 9 1. RS-232C output terminal (D-sub 9 pin) (See page 24.) 2. RS-232C input terminal (D-sub 9 pin) (See page 24.) 3. A V3 input terminal (BNC) (See page 10.) 4. A V2 input terminals (BNC) (See page 10.
9 E How to Install the Monitor Mounting precautions • Since the monitor is heavy , consult your dealer before installing, removing or moving the monitor . • When installing, removing or moving the monitor , ensure that this is carried out by at least 3 people.
10 E Connecting Peripheral Equipment Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to mix up the input terminal with the output terminal when connecting cables.
E 11 Connecting Peripheral Equipment Other terminals PC/A V audio output terminals • Audio from the equipment connected to the A V audio input terminals or PC audio input terminal is output. Connect to the audio input terminals of the connected equipment using a commercially available audio cable (RCA).
12 E Installing and removing the remote control batteries How to install the batteries 1. Press the cover gently and slide it in the direction of the arrow . 2. See the instructions in the compartment and put in the supplied batteries (2 R-6 batteries) with their plus (+) and minus (-) sides oriented correctly .
13 E Removing the T emporary Stand and the Handles n Removing the T emporary Stand Prepare wall-hanging brackets or a stand to mount the monitor unit. Read the manual for the brackets or stand for the proper mounting procedure. (The screw holes for mounting brackets (M10 x 4 holes) are provided on the rear of the monitor .
14 E T urning Power On/Off Caution • T urn on the monitor fi rst before turning on the PC or playback device. T urning on the main power Main power switch When the main power switch is off, the monitor cannot be turned on using the POWER button on the remote control unit.
15 E Basic Operation 1 2 3 4 5 6 7 8 1. INPUT (Input mode selection) The menu is displayed. Press or to select the input mode, and press to enter . * Y ou can select the input terminal by pressing the input switch of the monitor .
E 16 Basic Operation n Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it fi lls the entire screen. A V input An image with a 4:3 aspect ratio is stretched to fi ll the entire screen.
17 E Menu Items Displaying the menu screen Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 18 to 20 for details of each menu items. n Example of operation (Adjusting CONTRAST in the PICTURE menu) 1.
E 18 Menu item details The menu will differ depending on the input mode. n SCREEN (PC2/PC3) AUTO The CLOCK, PHASE, H-POS, and V -POS are automatically adjusted.
E 19 n SETUP OSD H-POSITION Adjusts the horizontal display position of menu screen. OSD V -POSITION Adjusts the vertical display position of menu screen. SCREEN MOTION Residual images are reduced by moving the screen. P A TTERN 1 .... The whole screen moves vertically and horizontally .
E 20 Menu Items TIPS • When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST and GAMMA cannot be set. • If COLOR MODE is set to sRGB or VIVID, the following items cannot be set.
E 21 Menu Items n Enlarge Y ou can align 4, 9, 16, or 25 monitors and integrate them into a single large screen to display . Enlarged views of separated images are displayed in each monitor .
E 22 Adjustments for PC screen display n Automatic adjustment When you use the PC2 input terminal or PC3 input terminals to display a PC screen for the fi rst time, or when you change the setting of the PC, use the automatic screen adjustment. 1. Switch the input to PC2 or to PC3 and display the adjustment pattern.
23 E Initialisation (Reset)/Functional Restriction Setting Y ou can return the settings to their factory-preset values and restrict operations. 1. After pressing SIZE for about 5 seconds, press , , , and in that order . OFF ON ON UNLOCKED FUNCTION 1/1 ALL RESET ADJUSTMENT LOCK OSD DISPLA Y LED RS-232C END···[MENU] 2.
24 E Controlling the Monitor with a PC Y ou can control this monitor from a PC via RS-232C (COM port) on the PC. Y ou can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 25), you can make input mode selection/adjustment or can check the status of a speci fi c monitor.
E 25 Controlling the Monitor with a PC n Response code format When a command has been executed correctly OK Return code (0D H , 0A H ) A response is returned after a command is executed.
E 26 Controlling the Monitor with a PC n Commands for ID control The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST ......... A monitor receiving this command sets its own ID number in the parameter fi eld.
E 27 Controlling the Monitor with a PC n Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. Y ou can use Repeater control function without assigning ID numbers.
E 28 RS-232C command table How to read the command table Command: Command fi eld (See page 24.) Direction: W When the “Parameter” is set in the parameter fi eld (see page 24), the command functions as described under “Control/Response Contents”.
E 29 PICTURE menu Function Command Direction Parameter Reply Control/Response contents * AUTO AGIN W 1 When the input mode is PC2, PC3. No CONTRAST CONT WR 0-60 0-60 0-127 on PC2/PC3. Ye s BLACK LEVEL BL VL WR 0-60 0-60 0-127 on PC2/PC3. TINT TINT WR 0-60 0-60 When the input mode is A V .
E 30 OPTION menu Function Command Direction Parameter Reply Control/Response contents * DA TE/TIME SETTING DA TE WR AABBCCDDEE AABBCCDDEE AA: Y ear , BB: Month, CC: Day , DD: Time, EE: Minute Ye s SCH.
E 31 Initialisation/Functional Restriction Setting (FUNCTION) menu Function Command Direction Parameter Reply Control/Response contents * ALL RESET RSET W 0 No ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF Y.
32 E T roubleshooting Before calling for repair services, make sure following checks for possible remedies to the encountered symptoms. There is no picture or sound. • Is the power cord disconnected? (See page 12.) • Is the main power switch set to “OFF”? (See page 14.
33 E Speci fi cations n Product Speci fi cations Model LDT651P LCD element 65" wide (163.9 cm diagonal) ASV low-reflection black TFT LCD Max. resolution (pixels) 1080 x 1920 Max. colours 16.77 M colours (8 bits/colour) Pixel pitch 0.744 mm (H) x 0.
E 34 n Compatible signal timing (PC) VESA Wide US TEXT Sun Screen resolution Hsync Vsync Dot frequency Analogue signal 640 x 480 800 x 600 848 x 480 1024 x 768 1 152 x 864 1280 x 768 1280 x 960 1280 x 1024 1360 x 768 1600 x 1200 *1 1280 x 720 1920 x 1080 720 x 400 1024 x 768 1 152 x 900 1280 x 1024 1600 x 1000 31.
E 35 Speci fi cations n PC1/A V1 input terminal pins (DVI-D24 pin) No. 1 2 3 4 5 6 7 8 9 10 11 12 Function TMDS data 2- TMDS data 2+ TMDS data 2/4 shield N.C. N.C. DDC clock DDC data N.C. TMDS data 1- TMDS data 1+ TMDS data 1/3 shield N.C. No. 13 14 15 16 17 18 19 20 21 22 23 24 Function N.
36 E M E M O.
.
North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www .mitsubishielectr ic.ca Inf or mation T echnologies Group , 4299 14th Av enue , Markham, Ontario L3R 0J2, Canada Sales Phone :+1-(905) 475-7728 F ax :+1-(905) 475-7958 E-mail :projectors@mitsubishielectric.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Mitsubishi Electronics LDT651P c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Mitsubishi Electronics LDT651P - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Mitsubishi Electronics LDT651P, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Mitsubishi Electronics LDT651P va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Mitsubishi Electronics LDT651P, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Mitsubishi Electronics LDT651P.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Mitsubishi Electronics LDT651P. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Mitsubishi Electronics LDT651P ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
