Manuel d'utilisation / d'entretien du produit 0927678D du fabricant Miele
Aller à la page of 72
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Guide to the appliance .............................................5 Appliance overview .................................................5 Control panel ......................................................6 Warning and Safety instructions .........
Cutlery ..........................................................3 1 3D cutlery tray (depending on model) ...............................3 1 Cutlery basket (depending on model) ...............................3 2 Operation ............................
Maintenance .....................................................5 9 Cleaning the water inlet filter .........................................5 9 Cleaning the drain pump and non-return valve ...........................6 0 After sales service .........
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Programmes b Time display c Programme sequence indicators d Check/Refill indicators e Start/Stop button with indicator light f Delay start button with indicator light g Turbo button with indicator light h Programme selector button i On/Off button K This instruction book applies to several different dishwasher models.
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
~ Keep children away from detergents. Dishwasher detergents contain irritant and corrosive ingredients which can cause burning in the mouth, nose and throat if swallowed, or inhibit breathing. Keep children away from the dishwasher when the door is open.
~ The appliance must not be used in a non-stationary location (e.g. on a ship). ~ Do not install the dishwasher in a room where there is a risk of frost. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
Installation ~ The dishwasher must be installed and connected in compliance with the diagram supplied. ~ The dishwasher must be correctly aligned to ensure problem-free operation. ~ In order to ensure stability, built-under and integrated dishwashers must only be installed under a continuous worktop which is secured to adjacent cabinetry.
~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling .
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Energy saving dishwashing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your water supply is suitable, this dishwasher can be connected to a hot water supply for further economies.
To open the door ^ Reach under the handle and pull the door open. If the door is opened during operation all functions are automatically interrupted. To close the door ^ Push the baskets right in. ^ Then raise the door up, and push until it clicks into position.
Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 °d – German scale) needs to be softened.
Programming the water hardness level Each time a button is pressed, one of the indicator lights will flash and light up in the control panel. However, only the indicator lights mentioned in the following programming process stages are significant. The programming procedure can be cancelled at any time by pressing the On/Off button K .
°d mmol/l °f Value displayed 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-50 51-60 61-70 0.2 0.4 0.5 0.7 0.9 1.1 1.3 1.4 1.6 1.8 2.0 2.2 2.3 2.5 2.7 2.9 3.1 3.2 3.4 3.6 3.8 4.0 4.1 4.3 4.5 4.7 4.
Before using the appliance for the first time, you require: – approx. 2 litres of water, – approx. 2 kg dishwasher salt*, – domestic dishwasher detergent*, – rinse aid* formulated for domestic dishwashers. * See "Optional accessories".
^ Remove the lower basket and unscrew the salt reservoir cap. Water or saline solution will run out of the reservoir when the cap is removed. It should therefore only be removed in order to refill the salt reservoir. ^ Fill the reservoir with approx. 2 litres of water (first use only).
Switching off the refill indicators If you only ever use combination products containing salt and rinse aid in your dishwasher, you can disable both of these indicators off if you wish.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid.
Setting the rinse aid dosage You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. It is set to a recommended setting of approx. 3 ml at the factory. If the Adjust Sensor wash function has been activated, the amount of rinse aid dispensed in the Sensor wash programme can be higher than that set.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when running the Tall items 65 °C programme, if available). ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc.
Jumbo cup rack (depending on model) The cup rack can be set at two different widths so that it can also accommodate large cups. ^ Pull the cup rack upwards and click it back into position at the required width. Support rail (depending on model) This rail is designed to hold tall glasses and glasses with stems securely.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the lower or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Glasses, cups and small items such as saucers can also be placed in the lower basket.
MultiComfort area The rear section of the lower basket is used for washing cups, glasses, plates, pots and pans. ^ The glass rack can be raised to make more room for tall items. ^ Stem glassware, e.g. wine glasses or champagne flutes, can be leaned against the glass rack or suspended from it.
Cutlery 3D cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling.
, Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled.
Switching on ^ Make sure the spray arms are not obstructed. ^ Close the door. ^ Open the stopcock, if it is closed. ^ Switch the dishwasher on using the On/Off button K . The Start/Stop indicator light will flash and one of the programme indicator lights will come on.
Display The duration of the programme selected appears in hours and minutes in the display before the programme begins. During the programme, the time left until the end of the programme is displayed. The time displayed may vary with the same programme.
Programme sequence indicators After a programme has been started the current stage of the programme is indicated by the programme sequence indicator lights. At the end of the programme A programme has finished when a " 0 " appears in the display and the "End" programme sequence indicator lights up.
Interrupting a programme A programme is interrupted as soon as the door is opened. If the door is closed again, the programme will continue from the point it was at before the door was opened. , Water in the dishwasher may be hot. Danger of scalding. Only open the door if absolutely necessary and exercise extreme caution when doing so.
Turbo The Turbo function is used to reduce the duration of programmes in which this function is available. In order to achieve optimum cleaning results, consumption rates are increased when Turbo has been selected.
Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A Delay start time of between 30 minutes and 24 hours can be selected. With a Delay start time of between 30 minutes and 9 hours 30 minutes, the time is set in 30 minute increments.
The time starts counting down until the programme start time: in 1 hour steps for delay start periods of over 10 hours, and in minutes for delay start periods of under 10 hours. At the end of the delay period, the programme selected begins automatically.
Adjust Sensor wash You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. ^ Switch the dishwasher off using the On/Off button K . ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K .
Memory You can use the Memory function to save the last programme selected. Instead of the indicator light for the ECO programme, the indicator light for the last programme selected will come on when the dishwasher is switched off and back on again or the door is opened and then closed at the end of a programme.
Optimise standby To save energy, the dishwasher will switch to Standby mode a few minutes after the last time a button has been pressed or a few minutes after the end of the programme. The indicator lights and the time display will go out and only the Start/Stop indicator will flash slowly.
Factory default If you have altered any settings from the factory default, you can re-set them back to the factory default settings as follows: ^ Switch the dishwasher off using the On/Off button K . ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K .
Check your dishwasher regularly (approx. ever y4-6 months). This way faults and problems can be avoided. , The external surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the external surfaces.
Cleaning the door front , Remove any soiling immediately. If this is not done, it might become impossible to remove and could cause the external surfaces to alter or discolour. ^ Clean the front using a damp Miele microfibre E-cloth*, or with a clean sponge and a solution of hot water and washing-up liquid.
Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , This dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department.
Problem Possible cause Remedy The Wash/Rinse, Drying and End indicator lights flash simultaneously. Fault code FXX shows in the time display. There may be a technical fault. – Switch the dishwasher off using the On/Off button K . After a few seconds: – Switch the dishwasher back on.
Water inlet/drain fault Problem Possible cause Remedy The Inlet/Drain check indicator flashes. The stopcock is closed. Open the stopcock fully. The dishwasher stops during a programme. The Inlet/Drain check indicator flashes. Fault code FXX shows in the display.
General problems Problem Possible cause Remedy The time display is dark. The Start/Stop indicator is flashing slowly. The time display has switched off automatically to save energy (Standby mode). Press any button. This switches off Standby. Detergent residue is left in the dispenser at the end of a programme.
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme. See Programme chart.
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid (see "Before using for the first time - Rinse aid").
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glasses are not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
Crockery Food deposits Action required Mixed, everyday crockery All normal food deposits This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic Fresh, easily removed food deposits This needs a short programme... Mixed crockery This needs a gentle programme with glass care.
Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 tab + Turbo option Quick wash 40°C – 25 ml or 1 tab 3) Sensor wash gentle – 25 ml or 1 tab Light soiling 50°C .
Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 12 Sensor wash Variable programme sequence, sensor controlled adjustment according to the amount of crockery an.
Consumption 2) Duration 2) Electricity Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 0.95 3) -1.35 4) 0.70 3) -1.00 4) 10.0 3) -17.0 4) 1:36-2:38 1:23-2:21 0.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, from the Miele Spare Parts Department or via the Internet at www.miele-shop.com (some may be supplied as standard, depending on model).
Electrical connection U.K. , All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model Standard XXL Height freestanding model 84.5 cm (adjustable + 3.5 cm) - Height built-in model 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.
71.
Alteration rights reserved/ G5400/G5405 / 1112 M.-Nr. 09 276 780 / 00.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Miele 0927678D c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Miele 0927678D - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Miele 0927678D, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Miele 0927678D va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Miele 0927678D, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Miele 0927678D.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Miele 0927678D. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Miele 0927678D ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
