Manuel d'utilisation / d'entretien du produit MPH2410 du fabricant Memorex
Aller à la page of 37
MODEL: MPH2410 BEFORE OPERA TING THIS PRODUCT , PLEASE READ THESE INSTRUCTIONS COMPLETEL Y . CORDLESS TELEPHONE WITH CALLER ID OPERA TING INSTRUCTIONS MPH2410.
1 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
2 IMPORT ANT SAFETY PRECAUTIONS (CONTINUED) When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions.
1. If your local telephone exchange only accepts Pulse dialing, you may have to switch the Tone/Pulse switch to Tone to access certain services that require Tone signalling (such as home banking). After the initial line is connected to the number you are calling, switch the Tone/Pulse switch to Tone to access Tone signalling.
Important Safety Precautions ........................1 Contents ........................................................4 Location of Controls and Indicators ...............5 Installation Instructions ..................................6 Wall Mounting the Unit (Standard Wall Jack) .
5 LOCA TION OF CONTROLS AND INDICA TORS 1 2 3 4 6 10 9 16 15 14 13 12 11 7 8 5 HANDSET 20 23 19 18 17 21 22 BASE 1. Handset Antenna 2. NEW CALL/MSG WTG Indicator 3. Display 4. TALK Button 5. Scroll Up/Down/Left/Right Buttons 6. VOICE MAIL/MENU Button 7.
1. Carefully unpack and remove your unit from the box. 2. Make sure all of the following items have been included: 3. Make sure the Rechargeable Battery is installed or install the Rechargeable Battery as described on page 9. PLEASE REFER TO FIGURE 1 FOR STEPS 4 THROUGH 7: 4.
7 INST ALLA TION INSTRUCTIONS (CONTINUED) W ALL MOUNTING THE UNIT (ST ANDARD W ALL JACK) Follow the instructions below to install the base onto a standard telephone wall jack: 1. Connect the short telephone line cord to the TEL LINE jack on the rear of the base unit.
W ALL MOUNTING THE UNIT (NO ST ANDARD W ALL JACK) 1. Drill two holes with a vertical distance between the two marked positions of 3 15/16" (100mm). 2. Drive a screw into each of the holes. Tighten them to the end of the screw lines, only leaving the smooth part of the screw head outside the wall.
9 INST ALLA TION INSTRUCTIONS (CONTINUED) Remove the battery cover located on the rear of the handset by pressing on the top cover and sliding it downward. 1 Connect the Ni-Cd battery pack plug into the battery connector; the LCD display will turn on in the Standby mode.
10 SET -UP INSTRUCTIONS SETTING THE RINGER VOLUME Set the ringer volume (HI, LOW, OFF) while in the Standby mode as follows: Press and hold the VOICE MAIL/ MENU button for more than two seconds; the Ringer Volume setting will appear in the display. 1 Press the EDIT/FLASH button to change the setting; the Ringer Volume setting will blink.
11 SET -UP INSTRUCTIONS (CONTINUED) SETTING THE LANGUAGE Set the language (ENGLISH, SPANISH, FRENCH) while in the Standby mode as follows: Press and hold the VOICE MAIL/ MENU button for more than two seconds; the Ringer Volume setting will appear in the display.
12 SET -UP INSTRUCTIONS (CONTINUED) SETTING THE FIRST RING This feature will turn the first ring of the phone On or Off. Set to Off so the phone does not ring until the Caller ID information has been displayed.
13 SET -UP INSTRUCTIONS (CONTINUED) SETTING THE TIME AND DA TE Change the Time and Date while in the Standby mode as follows: Press and hold the VOICE MAIL/ MENU button for more than two seconds; the Ringer Volume setting will appear in the display.
14 SET -UP INSTRUCTIONS (CONTINUED) SETTING THE LCD CONTRAST If you find the LCD screen difficult to read, set the contrast level while in the Standby mode as follows: Press and hold the VOICE MAIL/ MENU button for more than two seconds; the Ringer Volume setting will appear in the display.
15 SETTING THE PBX NUMBER This feature will insert a number (0-9) before the outgoing number, if required. When a number is selected, the unit will automatically dial the preset PBX number and a pause before any speed dial or Caller ID callback.
16 SETTING THE FLASH TIME This unit enables you to select the standard flash time applicable to your calling area, which is useful when “clicking” over to a call waiting call or for PBX systems. If you are not sure of the flash time, call your local telephone company.
17 SETTING THE P AUSE TIME This unit enables you to change the number of seconds that a pause lasts when using programmed pauses in your speed dial numbers or after your PBX number.
18 SETTING THE VOICE MAIL This unit enables you to store the Voice Mail Post Code number in your area. This will automatically connect you to the Voice mail server provider with one touch dialing.
19 SETTING THE MESSAGE W AITING The unit’s Message Waiting setting is set to OFF by default. Message Waiting will turn on automatically only when your local phone company sends the signal provided that this optional service is available in your area.
20 SETTING THE AREA CODE This unit does not require any programming of an area code. However, this setting could be used to add the local area code to numbers that were stored as 7 digits in the memory and/or 10 digit dialing if required by the local telephone company.
21 TELEPHONE OPERA TION PLACING A CALL After the battery has been fully charged, press the TALK button and listen for a dial tone; the timer will start counting in the display. 1 Press the Key buttons (0-9) ❶ to dial the phone number you wish to call.
22 RECEIVING A CALL Up to 80 incoming calls are saved in the Caller ID log. Make sure that the Caller ID service is turned on by your phone company. When you receive a call, the display will show the name of the caller and number of the call. To answer the call, press the TALK button.
23 TELEPHONE OPERA TION (CONTINUED) REDIALING A NUMBER Press the TALK button ❶ (the display will light), followed by the SAVE/RE/ PA button ❷ to automatically redial the last number dialed on this handset (up to 32 digits). NOTE: Please note that only the last number you called on this handset can be stored in the Redial memory.
24 TELEPHONE OPERA TION (CONTINUED) P AGING THE HANDSET Press the PAGE button on the base to locate the handset when not in use; the handset will beep for one minute and “PAGING” will appear in the display during paging. Press the PAGE button again on the base to stop.
25 TELEPHONE OPERA TION (CONTINUED) MESSAGE WAITING FUNCTION When a caller has recorded a message on a personal message service, “MSG WAITING” will appear in the display and the NEW CALL/MSG WAITING indicator will blink green. These will disappear when you retrieve your message.
26 TELEPHONE OPERA TION (CONTINUED) CHECKING THE CALLER ID LOG While the handset is in the Standby mode, press the Scroll Up ❶ or Down ❷ button; any unviewed (new) caller ID information will be displayed first. The information of the call, including name, number, date and time received will be displayed.
27 TELEPHONE OPERA TION (CONTINUED) DIALING A NUMBER IN THE CALLER ID DISPLA Y You can automatically call a number from the caller ID log as follows: Scroll through the calls to select a number to call using the Scroll Up ❶ or Down ❷ button. 2 1 1 Press the Option/# button to change the displayed number to 7, 10 or 11 digits.
28 TELEPHONE OPERA TION (CONTINUED) STORING NAMES & TELEPHONE NUMBERS IN THE PHONEBOOK The memory can store up to 40 name/telephone numbers. Press the DIR button while in the Standby mode. 1 Press the EDIT/FLASH button to create a new directory entry.
29 TELEPHONE OPERA TION (CONTINUED) CHARACTER MAP CHART Key 1 press 2 press 3 press 4 press 5 press 6 press 7 press 8 press 9 press 1 Space 1 & ‘ ( ) . 2A B C abc 2 3D E F def 3 4G H I ghi 4 5J K L jk l5 6M N O m no6 7P Q R S pqr s 7 8T U V t uv 8 9W XYZ w xyz9 00 ## VIEWING THE PHONEBOOK Press the DIR button.
30 TELEPHONE OPERA TION (CONTINUED) SA VING CALLER ID INFORMA TION TO THE PHONEBOOK The Phonebook can save the information directly from the caller ID. Scroll through the calls to select a number using the Scroll Up ❶ or Down button ❷ . 2 1 1 Press and hold the SAVE/RE/PA button; “SAVED” will appear in the display.
31 TELEPHONE OPERA TION (CONTINUED) EDITING TELEPHONE NUMBERS/NAMES You can edit a phone number in the Phonebook as follows: While in the Standby mode, press the DIR button 1 Press the Scroll Up ❶ or Down button ❷ to locate the desired Phonebook entry.
32 TELEPHONE OPERA TION (CONTINUED) DELETING A NUMBER FROM THE PHONEBOOK Delete a number from the Phonebook as follows: Press the DIR button ❶ while in the Standby mode and locate the entry to be deleted using the Scroll Up ❷ or Down button ❸ . 3 1 2 1 Press the DEL/CHAN button ; “ERASE ITEM?” will appear in the display.
SYMPTOM SOLUTION No dial tone Check that the telephone line cord connectors at both ends are pushed in firmly until they click. If you had a power failure or had unplugged the base unit, return the handset on the base unit for five to 10 seconds to reset the system.
34 SYMPTOM SOLUTION The Caller ID LCD Check the power connections. panel is blank Check the telephone line cord connections. Check the batteries for proper installation. The handset LCD panel will only start displaying information after the first call is received.
35 CARE AND MAINTENANCE 1. Clean your phone with a damp (never wet) cloth. Solvent or detergent should never be used. 2. A void operating your unit under direct sunlight or in hot, humid or dusty places. 3. Keep your unit away from heating appliances.
Memcorp, Inc. Weston, FL Printed in Hong Kong Visit our website at www .memorexelectronics.com MPH2410.O/M.QXD 3/7/03 9:35 AM Page 36.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Memorex MPH2410 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Memorex MPH2410 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Memorex MPH2410, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Memorex MPH2410 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Memorex MPH2410, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Memorex MPH2410.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Memorex MPH2410. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Memorex MPH2410 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
