Manuel d'utilisation / d'entretien du produit AfterBurner du fabricant MegaTech
Aller à la page of 20
Entire Contents ©2005 Megatech International O WNERS MANU AL ®.
Getting Acquainted with Y our AfterBurner .....................................3 Safety W arnings ...............................................................................3 The Radio System .......................................................
Review the components of the AfterBurner to ensure that your kit is complete before you begin fi nal assembly . (See Figure 1 ) Kit Contents: A. AfterBurner Nitro-Powered High-Speed Funny Car B. 2-Channel Radio T ransmitter C. Body W ashers and Clips D.
This vehicle is not a toy and must be operated by an adult who will handle this car safely and take responsibility to avoid any injury . This model is designed to be operated only in appropriate areas.
Fuel is the most critical component for making your engine perform properly . Improper fuels will cause hard starting, poor performance, and excessive wear on the engine. Fuel for your vehicle must contain a blend of BOTH synthetic oil and castor oil.
Remove the antenna from the slot on top of the transmitter . Slide it into the hole on top of the transmitter and turn clock wise until snug. Do not over-tighten. A. Be sure that both the transmitter and receiver switches are in the “off” position.
the throttle trigger operates the slide carburetor . If the servos do not respond, remove the batteries and make sure they are installed correctly . E. T urn off the power switch on the car and then on the transmitter . Although your AfterBurner comes factory-assembled, it is important to fi nely adjust the steering trim before operating.
Important! For best performance, maximum enjoyment and longest service, your Q 1.6 HP engine must be properly broken in before you adjust it for maximum power . Breaking in your engine enables match- ing surfaces and parts to establish the correct running tolerances.
Figure 9 - Closing the high speed valve First, fully extend your antenna and turn the transmitter on. If the green light ever goes dark or the red light comes on, your transmitter batteries are low . Y ou should replace them right away . Next turn on the car ’ s receiver .
for another full tank of fuel. Be careful not to maneuver it too harshly or use any more than half throttle. T o adjust the high speed needle valve, carefully turn the high speed needle valve clockwise 1/8 of a turn at a time. This allows the engine to run faster and at a higher pitch sound.
The Brake System Before running your AfterBurner , be sure to do a brake check. W ith the car runing at idle, roll it forward. It should roll freely . Now roll the car forward again and push the throttle trigger forward. The car should come to a stop almost immediately .
Proper care and simple maintenance should keep your AfterBurner running well for a long time. Make sure you thoroughly check your vehicle after each run to make sure no parts were bent or broken. Also check to make sure the screws, fasteners, bolts and hardware are secure and tight after each run.
13 Parts Listing P ar ts Listing Part# Description 1685 5*8*2.5 Premium Bearing (2 Pack) 16109 Side Exhaust Header 780201 Air Filter 780203 Flywheel 780204 Radio Box 780205 2-speed Spur Gear 42t 780206 2-speed Spur Gear 38t 780207 Suspension Hinge Pins (50mm) 780215 Brake Pads (Pr) 780218 Brake Disc 780222 Suspension Arms 780224 Upper Arms (Pr .
780204 780243 780243 781043 780225 780225 780293 780207 781032 780224 780293 780294 780296 780227 780222 781060 780305 780297 781105 781032 781032 780239 780226 780226 781040 780304 780310 780205 7802.
780204 780243 780243 781043 780225 780225 780293 780207 781032 780224 780293 780294 780296 780227 780222 781060 780305 780297 781105 781032 781032 780239 780226 780226 781040 780304 780310 780205 7802.
16 Limited W ar ranty Megatech Product Support If you hav e questions about your model, or you’ re having a problem with your model simply call us at 1-201-662-2800. Our customer support team is av ailable from 10:30am to 4:30pm eastern standard time to answer your questions.
17 state to state. Megatech is not obligated to pro vide upgraded products at a reduced rate when a previous product’ s production cycle has ended. Me gatech reserves the right to modify warranty provisions without notice.
MT C7810 D ARK THUNDER NITRO POWERED HIGH SPEED DRAGSTER MT C7501 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER P A CK FOR A UT O ST ART VEHICLES MT C7502 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER.
MT C7501 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER P A CK FOR A UT O ST ART VEHICLES MT C7502 CHRIS CHIANELLI SIGNA TURE Q-SERIES COMPLETER P A CK FOR PULL ST ART VEHICLES MT C7805 TEMPEST GLADIA .
www .me ga tec h.com Megatech International - 8300 T onnelle A venue North Bergen NJ 07047 - (201) 662-2800.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté MegaTech AfterBurner c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du MegaTech AfterBurner - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation MegaTech AfterBurner, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le MegaTech AfterBurner va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le MegaTech AfterBurner, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du MegaTech AfterBurner.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le MegaTech AfterBurner. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei MegaTech AfterBurner ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
