Manuel d'utilisation / d'entretien du produit TE653ELW-M du fabricant Meade
Aller à la page of 24
TE653ELW-M Complete Weather Forecaster with Indoor/ Outdoor Temperature and Humidity USER MANUAL MADE IN CHINA.
INTRODUCTION Thank you for selecting a Meade Instruments W eather Forecaster . This device combines precise time keeping, monitoring and displaying of current temperature data from up to three remote locations (additional sensors are required).
INST ALLA TION Communications between the main unit (receiver) and the remote sensor (transmitter) is wireless. This allows you to greater flexibility in choosing the location of remote sensor . The remote transmits data up to 164 feet (50 meters) over an open, unobstructed area.
4 REMOTE SENSOR FEATURES • Remote temperature transmission to the main unit via 433 MHz signal • Case can be wall mounted using built-in hanger • 164 feet transmission range without interference.
PLACEMENT • The remote sensor should be placed under eaves or a similar location with free air circulation, sheltered from direct sunlight and extreme weather . • Ideally , place the remote sensor over soil, rather than asphalt, which would cause false readings.
FRONT REAR 6 MADE IN CHINA A H G F E B L I D J K C M N O.
A. WEA THER FORECAST/ PRESSURE window B. TEMPERA TURE/ HUMIDITY window C. CLOCK window D. DOWN button • Select the next available mode • Press and hold for 2 seconds to search for wireless signal from remote sensor .
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
MADE IN CHINA Meade Instruments Corp. 27 Hubble Irvine, CA 92618 U.S.A. ©201 1 Meade Instruments Corp. All Rights Reserved. All user manual contents and information are subject to change.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Meade TE653ELW-M c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Meade TE653ELW-M - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Meade TE653ELW-M, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Meade TE653ELW-M va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Meade TE653ELW-M, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Meade TE653ELW-M.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Meade TE653ELW-M. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Meade TE653ELW-M ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
