Manuel d'utilisation / d'entretien du produit 2B020H1 du fabricant Maxtor
Aller à la page of 65
Maxtor 541DX Product Manual Models: 2B020H1, 2B015H1, 2B010H1 P/N:1546/A This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein – which will be incorporated in revised editions of the publication.
Before Y Before Y Before Y Before Y Before Y ou Begin ou Begin ou Begin ou Begin ou Begin Thank you for your interest in Maxtor hard disk drives. This manual provides technical information for OEM engineers and systems integrators regarding the installation and use of Maxtor hard drives.
i Contents Contents Contents Contents Contents Section 1 Section 1 Section 1 Section 1 Section 1 — Introduction Introduction Introduction Introduction Introduction Maxtor Corporation 1 - 1 Products .
ii Section 3 Section 3 Section 3 Section 3 Section 3 — Product Specifications Product Specifications Product Specifications Product Specifications Product Specifications Models and Capacities 3 - 1 .
iii Section 5 Section 5 Section 5 Section 5 Section 5 — AT Interface Description AT Interface Description AT Interface Description AT Interface Description AT Interface Description Interface Connect.
iv Write Verify Sector(s) 7 - 4 Write Sector Buffer 7 - 4 Write DMA 7 - 5 Write Multiple 7 - 5 Mode Set/Check Commands 7 - 6 Set Features Mode 7 - 6 Read Native Max Address 7 - 7 Set Max 7 - 7 Set Max.
v Figures Figures Figures Figures Figures Figure T itle Page 2 - 1 PCBA Jumper Location and Configuration 2 - 6 3 - 1 Outline and Mounting Dimensions 3 - 2 4 - 1 Multi-pack Shipping Container 4 - 2 4 .
INTRODUCTION 1 – 1 SECTION 1 Introduction Introduction Introduction Introduction Introduction Maxtor Corporation Maxtor Corporation Maxtor Corporation Maxtor Corporation Maxtor Corporation Maxtor Corporation has been providing high-quality computer storage products since 1982.
INTRODUCTION 1 – 2 Conventions Conventions Conventions Conventions Conventions If there is a conflict between text and tables, the table shall be accepted as being correct. Key Words Key Words Key Words Key Words Key Words The names of abbreviations, commands, fields and acronyms used as signal names are in all uppercase type (e.
PRODUCT DESCRIPTION 2 – 1 SECTION 2 Product Product Product Product Product Description Description Description Description Description Maxtor hard disk drives are 17.5 mm high, 3.5-inch diameter random access storage devices which incorporate an on-board Ultra ATA/100 interface controller.
PRODUCT DESCRIPTION 2 – 2 Product Product Product Product Product Features Features Features Features Features Functional / Interface Functional / Interface Functional / Interface Functional / Inter.
PRODUCT DESCRIPTION 2 – 3 Defect Management Zone (DMZ) Defect Management Zone (DMZ) Defect Management Zone (DMZ) Defect Management Zone (DMZ) Defect Management Zone (DMZ) Each drive model has a fixed number of spare sectors per drive, all of which are located at the end of the drive.
PRODUCT DESCRIPTION 2 – 4 Major HDA Components Major HDA Components Major HDA Components Major HDA Components Major HDA Components Drive Mechanism Drive Mechanism Drive Mechanism Drive Mechanism Drive Mechanism A brush-less DC direct drive motor rotates the spindle at 5400 RPM (±0.
PRODUCT DESCRIPTION 2 – 5 J U M P E R C ON F I GU R A T I ON Ma ste r /S la ve On l y dr iv e i n s ingl e d rive s y s t em * M ast e r driv e i n dual d ri v e s y s tem * S l av e d r i v e i n d.
PRODUCT SPECIFICATIONS 3 – 1 SECTION 3 Product Specifications Product Specifications Product Specifications Product Specifications Product Specifications Models and Capacities Models and Capacities .
PRODUCT SPECIFICATIONS 3 – 2 Physical Dimensions Physical Dimensions Physical Dimensions Physical Dimensions Physical Dimensions P ARAM ETE R V ALU E H eight (ty pica l mm ) 17.0 W i dth (t y pica l mm ) 101.6 Len gth (ty pic a l mm ) 14 6.1 We i g h t (m ax k g ) 0.
PRODUCT SPECIFICATIONS 3 – 3 Power Requirements Power Requirements Power Requirements Power Requirements Power Requirements Power Mode Definitions Power Mode Definitions Power Mode Definitions Power.
PRODUCT SPECIFICATIONS 3 – 4 Reliability Specifications Reliability Specifications Reliability Specifications Reliability Specifications Reliability Specifications Annual Return Rate Annual Return Rate Annual Return Rate Annual Return Rate Annual Return Rate < 0.
PRODUCT SPECIFICATIONS 3 – 5 EMC/EMI EMC/EMI EMC/EMI EMC/EMI EMC/EMI Radiated Electromagnetic Field Emissions - EMC Compliance Radiated Electromagnetic Field Emissions - EMC Compliance Radiated Elec.
INSTALLATION 4 – 1 SECTION 4 Handling and Installation Handling and Installation Handling and Installation Handling and Installation Handling and Installation Hard Drive Handling Precautions Hard Dr.
INSTALLATION 4 – 2 Unpacking and Inspection Unpacking and Inspection Unpacking and Inspection Unpacking and Inspection Unpacking and Inspection Retain any packing material for reuse. Inspect the shipping container for evidence of damage in transit. Notify the carrier immediately in case of damage to the shipping container.
INSTALLATION 4 – 3 Figure 4 - 2 Single Pack Shipping Container (Option A) Figure 4 - 3 Single Pack Shipping Container (Option B) Repacking Repacking Repacking Repacking Repacking If a Maxtor drive requires return, repack it using Maxtor packing materials, including the antistatic bag.
INSTALLATION 4 – 4 Before You Begin Before You Begin Before You Begin Before You Begin Before You Begin Important – Please Read Important – Please Read Important – Please Read Important – Please Read Important – Please Read Please read this installation section completely before installing the Maxtor hard drive.
INSTALLATION 4 – 5 Install the Hard Drive in a Device Bay Install the Hard Drive in a Device Bay Install the Hard Drive in a Device Bay Install the Hard Drive in a Device Bay Install the Hard Drive in a Device Bay Refer to your computer user’s manual for specific mounting information.
AT INTERFACE DESCRIPTION 5 – 1 SECTION 5 A A A A A T Interface Description T Interface Description T Interface Description T Interface Description T Interface Description Interface Connector Interfa.
AT INTERFACE DESCRIPTION 5 – 2 Pin Description Table Pin Description Table Pin Description Table Pin Description Table Pin Description Table P IN NAME P IN I/O S IG NAL NAME S I GNAL DE S C RIP TION R ESE T - 0 1 I H o s t R e set R es et s i gn al fr om t h e h os t s y s t em .
AT INTERFACE DESCRIPTION 5 – 3 T I M I N G P A R A METE R S M OD E 0 MOD E 1 M OD E 2 MOD E 3 M ODE 4 t 0 C y c l e Ti m e ( min ) 6 0 0 ns 3 8 3 ns 2 4 0 ns 1 8 0 ns 1 2 0 ns t1 A d dr es s v al i .
AT INTERFACE DESCRIPTION 5 – 4 DMA Timing DMA Timing DMA Timing DMA Timing DMA Timing T IMI N G P AR AME T E RS MO DE 0 MO DE 1 MO DE 2 t0 C y cl e T ime (mi n) 480 n s 150 n s 120 n s tC DM A C K t.
AT INTERFACE DESCRIPTION 5 – 5 Ultra DMA Timing Ultra DMA Timing Ultra DMA Timing Ultra DMA Timing Ultra DMA Timing T I M I N G P ARAME T ERS ( all ti m es in nan osec o nd s ) M ODE 0 M ODE 1 MOD E.
AT INTERFACE DESCRIPTION 5 – 6 Figure 5 - 5 Sustained Ultra DMA Data In Burst t DVH DSTROBE at d evice DD(15:0) at d evice DSTROBE at host DD(15:0) at host t DVH t CYC t CYC t DVS t DVS t DH t DS t .
AT INTERFACE DESCRIPTION 5 – 7 t AZ t IORDYZ CRC DMARQ ( device ) DMACK- (host) STOP (host) HDMARDY- (host) DSTROBE ( device ) DD(15:0) DA0, DA1 , DA2, CS0-, CS1- t ACK t LI t MLI t DVS t LI t ACK t.
AT INTERFACE DESCRIPTION 5 – 8 t DH t DS t DVH HSTROBE at host DD(15:0) at host HSTROBE at d evice DD(15:0) at d evice t DVH t CYC t CYC t DVS t DVS t DS t DH t 2CYC t DH t DVH t 2CYC DMARQ (device).
AT INTERFACE DESCRIPTION 5 – 9 DMARQ (device) DMACK- (host) STOP (host) DDMARDY- (device) HSTROBE (host) DD(15:0) (host) t SR t RFS t RP Figure 5 - 11 Device Pausing an Ultra DMA Data Out Burst DMAR.
AT INTERFACE DESCRIPTION 5 – 10 DMARQ (device) DMACK- (host) STOP ( host ) DDMARDY- ( device ) HSTROBE (host) DD(15:0) (host) DA0, DA1 , DA2, CS0- , CS1- t ACK t MLI t DVS t LI t LI t ACK CRC t DVH .
HOST SOFTWARE INTERFACE 6 – 1 SECTION 6 Host Software Interface Host Software Interface Host Software Interface Host Software Interface Host Software Interface The host communicates with the drive through a set of controller registers accessed via the host’s I/O ports.
HOST SOFTWARE INTERFACE 6 – 2 Sector Count Register Sector Count Register Sector Count Register Sector Count Register Sector Count Register Holds the number of sectors to be sent during a Read or Write command, and the number of sectors per track during a Format command.
HOST SOFTWARE INTERFACE 6 – 3 Command Register Command Register Command Register Command Register Command Register Contains code for the command to be performed. Additional command information should be written to the task file before the Command register is loaded.
HOST SOFTWARE INTERFACE 6 – 4 C O M M A N D N AM E CO M M AN D C O D E PA R A M E T E R S U S E D b7 b6 b5 b4 b3 b2 b1 b0 F S C S N C S D H R e c a l i b r a t e 0 001 xxxx N N N N D Re ad S ec t or.
HOST SOFTWARE INTERFACE 6 – 5 Control Diagnostic Registers Control Diagnostic Registers Control Diagnostic Registers Control Diagnostic Registers Control Diagnostic Registers These I/O port addresse.
HOST SOFTWARE INTERFACE 6 – 6 Reset and Interrupt Handling Reset and Interrupt Handling Reset and Interrupt Handling Reset and Interrupt Handling Reset and Interrupt Handling Reset Handling Reset Handling Reset Handling Reset Handling Reset Handling One of three different conditions may cause a reset: power on, hardware reset or software reset.
INTERFACE COMMANDS 7 – 1 SECTION 7 Interface Commands Interface Commands Interface Commands Interface Commands Interface Commands The following section describes the commands (and any parameters necessary to execute them), as well as Status and Error register bits affected.
INTERFACE COMMANDS 7 – 2 Read Commands Read Commands Read Commands Read Commands Read Commands Read Sector(s) Read Sector(s) Read Sector(s) Read Sector(s) Read Sector(s) Reads from 1 to 256 sectors, as specified in the Command Block, beginning at the specified sector.
INTERFACE COMMANDS 7 – 3 Read DMA Read DMA Read DMA Read DMA Read DMA Multi-word DMA Identical to the Read Sector(s) command, except that 1 . The host initializes a slave-DMA channel prior to issuing the command, 2 . Data transfers are qualified by DMARQ and are performed by the slave-DMA channel and 3 .
INTERFACE COMMANDS 7 – 4 Set Multiple Mode Set Multiple Mode Set Multiple Mode Set Multiple Mode Set Multiple Mode Enables the controller to perform Read and Write Multiple operations, and establishes the block count for these commands. Before issuing this command, the Sector Count register should be loaded with the number of sectors per block.
INTERFACE COMMANDS 7 – 5 Write Multiple Write Multiple Write Multiple Write Multiple Write Multiple Performs similarly to the Write Sector(s) command, except that: 1 . The controller sets BSY immediately upon receipt of the command, 2 . Data transfers are multiple sector blocks and 3 .
INTERFACE COMMANDS 7 – 6 Mode Set/Check Commands Mode Set/Check Commands Mode Set/Check Commands Mode Set/Check Commands Mode Set/Check Commands Set Features Mode Set Features Mode Set Features Mode Set Features Mode Set Features Mode Enables or disables features supported by the drive.
INTERFACE COMMANDS 7 – 7 Read Native Max Address Read Native Max Address Read Native Max Address Read Native Max Address Read Native Max Address This command returns the native maximum address. The native maximum address is the highest address accepted by the drive in the factory default condition.
INTERFACE COMMANDS 7 – 8 Power Mode Commands Power Mode Commands Power Mode Commands Power Mode Commands Power Mode Commands Standby Immediate – 94h/E0h Standby Immediate – 94h/E0h Standby Immediate – 94h/E0h Standby Immediate – 94h/E0h Standby Immediate – 94h/E0h Spin down and do not change time out value.
INTERFACE COMMANDS 7 – 9 Default Power-on Condition Default Power-on Condition Default Power-on Condition Default Power-on Condition Default Power-on Condition The drive’s default power on condition is the ACTIVE MODE.
INTERFACE COMMANDS 7 – 10 Initialization Commands Initialization Commands Initialization Commands Initialization Commands Initialization Commands Identify Drive Identify Drive Identify Drive Identify Drive Identify Drive Allows the host to receive parameter information from the drive.
INTERFACE COMMANDS 7 – 11 - WO R D C ON T EN T D ESC R I PT IO N 50 R e s e r v ed 51 - 5 2 Obs ol e t e 53 15 -3 = re s e rv ed 2, 1 = th e fie l ds su pp ort ed in w o r d s 8 8 ar e val i d , 0 =.
INTERFACE COMMANDS 7 – 12 W O R D CO NT E NT DE S C RIP TIO N 83 C o m m a nd se t s s upp o rt e d . If w o rd s 8 2 a nd 8 3 = 00 0 0 h o r F F F F h c o m m a nd s e t no t i f i c a t i o n no t s up p or t ed .
INTERFACE COMMANDS 7 – 13 Initialize Drive Parameters Initialize Drive Parameters Initialize Drive Parameters Initialize Drive Parameters Initialize Drive Parameters Enables the drive to operate as any logical drive type.
INTERFACE COMMANDS 7 – 14 Seek, Format and Diagnostic Commands Seek, Format and Diagnostic Commands Seek, Format and Diagnostic Commands Seek, Format and Diagnostic Commands Seek, Format and Diagnostic Commands Seek Seek Seek Seek Seek Initiates a seek to the track, and selects the head specified in the Command block.
INTERFACE COMMANDS 7 – 15 S.M.A.R.T. Command Set S.M.A.R.T. Command Set S.M.A.R.T. Command Set S.M.A.R.T. Command Set S.M.A.R.T. Command Set Execute S.M.A.R.T. Execute S.M.A.R.T. Execute S.M.A.R.T. Execute S.M.A.R.T. Execute S.M.A.R.T. The Self-Monitoring Analysis and Reporting Technology (S.
SERVICE AND SUPPORT 8 – 1 SECTION 8 Service and Support Service and Support Service and Support Service and Support Service and Support Service Policy Service Policy Service Policy Service Policy Se.
SERVICE AND SUPPORT 8 – 2 Asia/Pacific (APAC) Australia Languages supported: English Vo x + 61 2 9369 3662 Fax + 61 2 9369 2082 MaxFax + 61 2 9369 4733 BB S + 61 2 9369 4293 Sin ga po re Languages s.
GLOSSARY GL – 1 GLOSSAR Y Glossary Glossary Glossary Glossary Glossary A A A A A access To obtain data from, or place data into, RAM, a register, or data storage device. access time The interval between the issuing of an access command and the instant that the target data may be read or written.
GLOSSARY GL – 2 central processing unit (CPU) The heart of the computer system that executes programmed instructions. It includes the arithmetic logic unit (ALU) for performing all math and logic op.
GLOSSARY GL – 3 digital magnetic recording See magnetic recording. direct access Access directly to memory location. (See random access). direct memory access (DMA) A mean of data transfer between the device and host memory without processor intervention.
GLOSSARY GL – 4 frequency response A measure of how effectively a circuit or device transmits the different frequencies applied to it. In disk and tape drives this refers to the read/write channel. In disk drives, it can also refer to the dynamic mechanical characteristics of a positioning system.
GLOSSARY GL – 5 late window A data window that has been shifted in a late direction to facilitate data recovery. latency A delay encountered in a computer when waiting for a specific response. In a disk drive there is both seek latency and rotational latency.
GLOSSARY GL – 6 P P P P P parallelism 1. The condition of two planes or lines being parallel. Important in disk drives because a lack of it in mechanical assemblies can result in positioning inaccuracy. More precisely: planes-coplanar; lines-colinear.
GLOSSARY GL – 7 S S S S S sector A logical segment of information on a particular track. The smallest addressable unit of storage on a disk. Tracks are made of sectors. sector pulse signal A digital signal pulse present in hard sectored drives which indicates the beginning of a sector.
GLOSSARY GL – 8 strobe offset signal A group of digital input signal levels which cause the read PLL and/or data decoder to shift the decoding windows by fractional amounts.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Maxtor 2B020H1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Maxtor 2B020H1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Maxtor 2B020H1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Maxtor 2B020H1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Maxtor 2B020H1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Maxtor 2B020H1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Maxtor 2B020H1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Maxtor 2B020H1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
