Manuel d'utilisation / d'entretien du produit Loudspeaker Systems du fabricant MartinLogan
Aller à la page of 24
S CENARIO TM user ’s manual c l s e l e c t r o s t a t i c M ART I N L OGA N.
2 Contents C ONTENTS Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation in Brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Installation in Brief 3 I NST ALLA TION IN B RIEF W e know you are eager to hear your new Scenario loud- speakers, so this section is provided to allow fast and easy set up. Once you have them operational, please take the time to read, in depth, the rest of the information in this manu- al.
4 Introduction I NTRODUCTION Congratulations! Y ou have invested in one of the world’s premier loudspeak er systems. The MartinLogan Scenario represents the culmination of an intensive, dedicated gr.
O PERA TION Operation 5 Because your MartinLogan Scenario’s use an internal power supply to energize their electrostatic cells with high-voltage DC, they must be connected to an AC power source. F or this reason they are provided with the proper IEC standard power cords.
6 Placement P LACEMENT By now your speakers should be placed approximately two to three feet from the front wall, the wall in front of the listening position, and at least one to two feet from the side walls. Y our sitting distance should be further than the distance between the speakers themselves.
Placement 7 Imaging In their final location, your Scenario’s should have a stage width somewhat wider than the speakers themselves. On well recorded music, the instruments should extend beyond the edges of each speaker to the left and to the right, yet a vocalist should appear directly in the middle.
8 Room Acoustics This is one of those areas that requires both a little back- ground to understand and some time and experimentation to attain the best performance from your system. Y our room is actually a component and an important part of your system.
Room Acoustics 9 on the floor or solid surface, it can shake as it produces sound and, consequently , the sound can be compromised. If your speaker is sitting on the carpet and only foot gliders are used, the bass can be ill defined and even boomy . The use of spikes is recommended to insure secured footing for your speakers.
10 Dispersion Interactions Y our Scenario’s launch a 30 degree dispersion pattern when viewed from above. This horizontal dispersion field gives a choice of good seats for the performance while minimizing interactions with side walls (See F igure 6).
Dispersion Interactions 11 Figure 8 – 9. As can be seen here, point source concepts invite a great deal of room interaction. While delivering good frequency response to a large listening audience, imaging is consequently confused and blurred. Figure 10– 11.
It had long been the practice of stereo buffs to connect their television to the stereo system. The advantage was the use of the larger speakers and more powerful amplifier of the stereo system. Even though the sound was greatly improved, i t was still mono and limited by the broadcast signal.
How can sound be reproduced by something that you are able to see through? Electrostatic energy makes this possible. Where the world of traditional loudspeaker technology deals with cones, domes, diap.
ESL P anel Critical Zone: 500Hz–20kHz The most significant advantage of MartinLogan ’s exclusive transducer technology reveals itself when you look at examples of other loudspeaker products on the market today . The Scenario uses no crossover networks above 500 Hz because they are not needed.
Since the beginning of audio, achieving smooth dispersion has been a problem for all loudspeaker designers. Large panel transducers present even more of a challenge because the larger the panel, the more directional the dispersion pattern becomes.
16 Electrostatic Loudspeaker History In the late 1800s, any loudspeaker was considered exotic. T oday , most of us take the wonders of sound reproduction for granted. It was 1880 before Thomas Edison had invented the first phonograph. This was a horn-loaded diaphragm that was excited by a playback stylus.
Electrostatic Loudspeaker History 17 In 1947, Arthur Janszen, a young Naval engineer , took part in a research project for the Navy . The Navy was interested in developing a better instrument for testing microphone arrays.
18 Frequently Asked Questions F REQUENTL Y A SKED Q UESTIONS How do I clean my speak ers? Just use a dust free cloth or a soft brush to remove the dust from your speakers. W e recommend a specialty cloth (available through the XStatic shop at www .martinlogan.
Frequently Asked Questions 19 Will excessive smok e or dust cause any problems with my electrostatic speak ers? Exposure to excessive contaminants such as smoke or dust may potentially affect the performance of the electrostatic membrane, and may cause discoloration of the diaphragm membrane.
20 Troubleshooting T ROUBLESHOOTING No Output •Check that all your system components are turned on. •Check your speaker wires and connections. •Check all interconnecting cables. W eak Output, Loss of Highs • Check the power cord. Is it properly connected to the speaker? Exaggerated Highs, Brightness • Check the toe-in of the speakers.
21 The Scenario hybrid speaker system consists of a broad-range single element electrostatic transducer integrated with a quick- response woofer . This approach takes advantage of the benefits that both technologies have to offer . Dispersion is a controlled 30 degrees.
AC. Abbreviation for alternating current. Active crossover . Uses active devices (transistors, ICs, tubes) and some form of power supply to operate. Amplitude. The extreme range of a signal. Usually measured from the average to the extreme. Arc. The visible sparks generated by an electrical discharge.
23 Inductance. The property of an electrical circuit by which a varying current in it produces a varying magnetic field that introduces voltages in the same circuit or in a nearby circuit. It i s measured in henrys. Inductor . A device designed primarily to introduce inductance into an electrical circuit.
2101 Delaware Street, Lawrence, Kansas 66046, USA tel 785.749.0133 fax 785.749.5320 www.martinlogan.com c l s e l e c t r o s t a t i c M ART I N L OGA N ©2000 MartinLogan, All rights reserved Rev.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté MartinLogan Loudspeaker Systems c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du MartinLogan Loudspeaker Systems - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation MartinLogan Loudspeaker Systems, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le MartinLogan Loudspeaker Systems va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le MartinLogan Loudspeaker Systems, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du MartinLogan Loudspeaker Systems.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le MartinLogan Loudspeaker Systems. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei MartinLogan Loudspeaker Systems ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
