Manuel d'utilisation / d'entretien du produit 5620DWB du fabricant Makita
Aller à la page of 20
SPE( Mo Man 4 Note WAR& SAVE lped with Electric Brake IL5620DWA MODEL 5620DWB !h Capacity Battery Charger With High Capacity Battery Charger INSTRUCTION MANUAL CATIONS 620D Cutting depth No load speed Overall Net 900 450 (RPMI length weight 364 mm 3.
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit.
Pa mc to: M; to< *Ch ott sei *Us wt Sen Tot ma owt in I to !TIC tform. Holding the work by hand or against your body is unstable and to loss of control. use tool if switch does not turn it on or off. A tool that cannot be ed with the switch is dangerous and must be repaired.
Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade.
11 iauses and Operator Prevention of Kickback: rickback is a sudden reaction to a pinched, bound or misaligned saw blade, ausing an uncontrolled saw to lift up and out of the workpiece toward the Iperator.
Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICK BACK.
15 16 17 ace the wider portion of the saw base on that part of the workpiece which solidly supported, not on the section that will fall off when the cut is made. E examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, id Fig. 6 the WRONG way.
SYMBOLS The followings show the symbols used for tool. V ................................. volts A ................................. amperes Hz ................................. herts kg ................................. kilograms h ..................
I @1 2 3 4 5 6 7 8 *9 10 11 12. Length of Cord (Feet) 25 50 AWG Size of Cord 18 18 IPORTANT SAFETY INSTRUCTION’S FOR CHARGER & BATTERY CARTRIDGE 100 150 18 16 9.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Ins *A *TI it *TI tC 91 A PI di tc .D ei Ch .YI Y( tt D *PI tt in *In ai tr rc bi in .V rE *V ai cl 01 01 CP *TI N *LA fc dc it ,, illing or removing battery cartridge lays switch off the tool before insertion emoval of the battery cartridge.
*If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
He W co CI AI ar AI LC m Ai bi C .I ., B L a ti 0 Bevel scale plate wrench storage n not in use, the eniently stored. Screw hex wrench can be TION: iys be sure that the tool is switched off and the battery cartridge is removed before adjustment is attempted.
Adjusting for accuracy of 90" cut (vertical cut) This adjustment has been made at the factory. But if it is off, adust the adjusting screw with a screwdriver while squaring the blade with the base using a triangular rule, try- square, etc. Base I Fig.
01 Hc thi mi an Nc thi ad sa ad . co CL @P tc S @Ii ti GI Th ex thi thc thi al: PO pation the tool firmly. Set the base plate on vorkpiece to be cut without the blade ng any contact.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes reg- ularly. Replace when they wear down to the limit mark.
R To 1. 2. A 0 Tt m Tt .I f .I f 01 F Part No. Diameter Hole diameter (mm) (mm) cycling the Battery No, teeth The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I cycle the battery: ?move the battery from the tool.
Juns-10-'98 US 165 mm (6-1/2") CORDLESS CIRCULAR SAW Model 5620D Note: The switch and other part configurations may differ from country to country.
MCI MAKVA LIMrlED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from worfknshrp and materials for period of ONE YEAR from the date of original purchase.
MODEL 56200 "",M ,,!& DESCRIPTION MACHINE 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 1 13 1 14 1 15 1 16 1 17 I 10 1 10 2 20 1 21 1 22 3 23 6 24 1 25 2 26 1 27 1 26 1 29 1 30 1 31 .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Makita 5620DWB c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Makita 5620DWB - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Makita 5620DWB, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Makita 5620DWB va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Makita 5620DWB, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Makita 5620DWB.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Makita 5620DWB. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Makita 5620DWB ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
