Manuel d'utilisation / d'entretien du produit RV4000 du fabricant Magnadyne
Aller à la page of 24
Operation and Installation Manual ® RV4000 AM / FM Stereo Multi-Media Receiver EQ 1 AS/PS 2 SLP 3 ALM 4 DISP 5 DIM 6 PUSH 3-Beam Laser Pickup A B AUX AM/FM DISC SPEAKER SPK FM ST RESET AUX HEADPHONES.
Please take the time to read all of the information in this manual. Familiarity with operation and installation procedures will help you obtain the best possible performance from your new AM/FM Stereo Multi-Media Receiver. WARNING! To prevent fire or electrical shock hazard, do not expose this product to moisture, or remove cover or bottom screws.
Button Locations and Functions 3 1. Power On/Off: Press to turn the unit on or off. 2. Disc Door: To play a disc, insert the disc with label facing forward. 3. Disc Door Release: Press to open the door so the disc can be inserted. 4. Auxiliary Button (AUX): Press to choose auxiliary audio in mode.
4 Button Locations and Functions (Continued) 16 . Dimmer Button (DIM): Press to dim the lighting in the display area. Sequential presses will select dif- ferent levels of display area lighting. 17. Radio Preset Button (6): Recalls a memorized radio station, and programs a radio station into memory.
5 General Operations Selecting a Play Source: To select a play source, press one of the follow- ing mode buttons: AUX (Auxiliary Audio Input), AM/FM (AM or FM Radio Band) or DISC (Music) Dimming the Display: Press the DIM button to select the desired level of brightness for the display area.
6 Sound Controls Bass: Select the Bass mode by pressing the VOLUME knob. Increase the Bass by rotating the VOLUME knob clockwise. Decrease the Bass by rotating the knob counterclockwise. After 6 seconds control reverts back to volume control. Bass, Treble and Balance Control Select the desired sound mode by pressing the VOLUME knob.
7 Sound Controls (Continued) Mute: Press the button to mute the volume level. Press the button again to restore the volume. Speaker Selection Selecting Speaker Sets: • Press the A button to toggle speaker set A on and off. “SPK A” appears in the display when speaker set A is on.
8 Sleep Timer Operation Setting the Sleep Timer: 1. Press the SLP button until the “SLP 10” appears in the display. 2. Keep pressing the SLP button again until the desired sleep time appears in the display (00, 10, 20, 30, 40, 50, 60, 70, 80 minutes).
9 Alarm Operation Setting the Alarm Timer: 1. Press the ALM button and the clock will appear in the display with the hour number flashing. 2. Rotate the VOLUME knob until the correct Hour appears in the display. “ALM” will appear in the display indicating the alarm is activated.
10 Radio Operations Selecting the Play Source: Press the AM/FM button and “rAdIO” appears in the display. After a brief moment either AM or FM will appear in the display. Selecting the AM or FM: Press the AM/FM button repeatedly and select from FM 1, FM 2, FM 3, AM 1 or AM 2.
11 Disc Warnings DVD 12cm disc (Single-sided disc only) CD 12cm disc MP3 12cm disc Label side up Do not touch the underside of the disc Do not bend Wipe the disc from the center toward the outside edg.
12 Music Disc Operation General Operations: 1. Push the door access the disc player. 2. Insert the disc onto the hub with the label facing forward. Use your thumb to make sure the disc snaps onto the hub. 3. Press the DISC button and “LOAd” will appear in the display.
13 Music Disc Operation (Continued) Removing the Disc: 1. Push the door to access the disc player. Wait until the disc stops spinning before opening up the door. 2. Use your finger to remove the disc from the hub. 3. Close the door. Pausing the Disc: Press the ll button to pause the disc, press it again to resume play.
14 MP3 Disc Operation General Operations: 1. Push the door access the disc player. 2. Insert the disc onto the hub with the label facing forward. Use your thumb to make sure the disc snaps onto the hub. 3. Press the DISC button and “LOAd” will appear in the display.
15 MP3 Disc Operation (Continued) Removing the Disc: 1. Push the door to access the disc player. Wait until the disc stops spinning before opening up the door. 2. Use your finger to remove the disc from the hub. 3. Close the door. Pausing the Disc: Press the ll button to pause the disc, press it again to resume play.
16 Audio Input Selecting the Audio Input Source: Note 1: The RV4000 does not control the device, it just allows the audio to be played through the system. Note 2: If the rear audio input is being used once you plug a device into the front audio input jack the audio will be diverted to playing the front device.
17 The LCD display may fail to function normally due to the vehicle’s battery condition, and could require resetting the radio microprocessor if: • The vehicle has been “jump started” from a dead battery condition. • The vehicle battery becomes very low and is quick-charged.
18 Installation 9 4 5 / 8 ” 6 1 / 4 ” Chassis Opening Structural Stud Wall Panel Caution: Do not install radio without rear cover installed: No user -ser viceable parts inside.
19 Speaker Connections _ + Gray Wire White/Black Wire (Common -) _ + Gray/Black Wire Right Speaker B Left Speaker B _ + Brown/Black Wire White Wire (Common -) _ + Brown Wire Right Speaker A Left Speak.
20 Wiring and Auxiliary Connections Red Wire (+) to 12 Volt DC Power Black Wire Ground Music Disc Player (Optional) Audio In Audio Out 10A Fuse External Automotive Ty pe Antenna (Optional) In-Dash Uni.
21 Outdoor Antenna Grounding: If an outside antenna is connected to the receiver, be sure the antenna system is grounded, so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electrical Code, ANSI/NFPS No.
22 Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within one year from the date of sale to you, repair, replace or refund the retail sales price of said pro.
23.
© Copyright 2011 Magnadyne Corporation RV4000-UM Rev. A 5-19-11.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Magnadyne RV4000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Magnadyne RV4000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Magnadyne RV4000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Magnadyne RV4000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Magnadyne RV4000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Magnadyne RV4000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Magnadyne RV4000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Magnadyne RV4000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
