Manuel d'utilisation / d'entretien du produit SP1200 du fabricant Mackie
Aller à la page of 28
SP1200 MUSIC CONTROLLER INPUTS OFF 3 0 3 6 9 15 30 55 1234 ON OL STATUS POWER COMM PORT ZONE A MASTER VOLUME PHANTOM PAGING GAIN +40dB MIC /L INE INPUT A CAUTION: TO REDUCE THE RISK OF FIRE REPLACE WI.
SP1200 – 2 CAUTION AVIS RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ATTENTION: POUR EVITER LES RISQUES DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE.
SP1200 – 3 Audio expansion connectors are provided on the rear panel for connecting multiple SP1200s, with shared audio via balanced busing. Each of the four program input signals are internally balanced and can be independently assigned to the balanced bus with internal assignment switches.
SP1200 – 4 Fron t P anel Fea tures INPUTS select buttons are used to choose the program source for the zone. Only one source may be selected at a time. These are non-priority inputs. However , Input 4 can become a Program Priority Input by setting the AMP ADDRESS switch #7 UP .
SP1200 – 5 The P AGING MIC VOX variable control adjusts the ducking threshold for the paging mic. Rotate the control clockwise to reduce the threshold. Rotate the control counterclockwise to increase the threshold. MIC/LINE INPUT is provided to connect a local microphone.
SP1200 – 6 3. In st alla tion Applica tion Dia grams PHANTOM PAGING GAIN +40dB MIC /LINE INPUT A CAUTION: TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING 115V 60Hz FU SE 1 15/ T4A .
SP1200 – 7 PHANTOM PAGING GAIN +40dB MIC /LINE INPU T A CAUTION: TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING 115V 60Hz FUS E 1 15/ T4A 120 WATTS 230V 50H z FUSE 230/T 2A 120 WA.
SP1200 – 8 INTERNAL BUS ASSIGN SWITCHES S1 S5 12345678 ON 12345678 ON INTERNAL BUS ASSIGN SWITCHES SP1200 SWITCH SETTINGS 12345678 0 I ZONE A AMBIENT MIC OFF/ON OFF ON DOWN UP AMP ADDRESS INPUT 4 PR.
SP1200 – 9 D: Ro om C o mbining — Z ones Note: This application provides independent source selection for each zone, or common input source selection for both zones (room combining). Both DX8 Selection Remote Controls are used to select Presets 1 and 2.
SP1200 – 10 Applica tion s A: T ypi cal M on o Applica tion This diagram depicts a typical setup, using the SP1200 in a mono application. A Digital Satellite Service (DSS) is connected to Input 1, which also serves as the music-on-hold for the telephone system.
SP1200 – 11 CAUTION: When using multiple SP1200s that use the expansion bus, these switch settings must be unique to each unit or you can damage your SP1200(s). Never assign more than one program source to the same channel on the Expansion Bus. If there is a requirement for music-on-hold, use Input 1 for the continuous music source (i.
SP1200 – 12 Signal Pin No. Input 1 Left (+) Pin 1 Input 1 Left ( – ) Pin 14 Input 1 Right (+) Pin 2 Input 1 Right ( – ) Pin 15 Ground Pin 3 Input 2 Left (+) Pin 16 Input 2 Left ( – ) Pin 4 Inp.
SP1200 – 13 C onnect ing the RS485 Serial Por t This is a 3-pin Phoenix-type connector that follows standard RS485 protocol. Select either a data-grade shielded twisted pair cable or a standard 3-conductor microphone cable for this connection.
SP1200 – 14 EQ By pa ss Jumper J6, located on each Filter Board, allows you to bypass the 3-band EQ for the four Program Inputs. Jumper pins 1 and 2 to bypass the EQ. Jumper pins 2 and 3 to engage the EQ (default). Note: The top Input Board must be removed in order to access Jumper J6 on the Filter Board.
SP1200 – 15 A C P ower C on sidera tion s Each SP1200 draws an average of 3 amps of AC line current (@ 120V AC) when fully loaded and playing music with a relatively high crest factor . V ol t age C onv ersion The SP1200 can be configured to operate at 115V AC or 230V AC.
SP1200 – 16 4. Opera t ion • Bus Assign switches are used to assign a program input source to the balanced expansion bus. There are four switches for each program input source: Left (+), Left ( – ), Right (+), and Right ( – ).
SP1200 – 17 P A GING MIC C ONTROL The P AGING MIC CONTROL connector is provided to connect a manual paging switch. Connect a normally-open switch between GND and ZONE A (to page in Zone A only), or GND and ALL CALL ( to page over the entire system--if using multiple units).
SP1200 – 18 Using Input s 1-4 Connect the program sources to Inputs 1-4. These could include a CD player , tape deck, tuner , satellite feed, TV audio, jukebox, or an audio feed from a live band. All four program inputs use unbalanced RCA connectors and accept stereo line- level signals.
SP1200 – 19 Using t he P aging Mic The paging mic is used to make announcements over the system. If the paging mic is a condenser mic or other type of mic that requires phantom power , move the PHANTOM switches to the down position. Otherwise, leave them switched up.
SP1200 – 20 Ambien t Mi c Calibra tion and P lacemen t 1. Connect the MT -3100 (or other microphone) to the AMBIENT MIC connector on the rear panel. Make sure the ambient mic switch is on ( AMP ADDRESS switch #8 up). Locate the ambient mic in an appropriate position to pick up the ambient noise in the room.
SP1200 – 21 Using the EQ Each local MIC/LINE INPUT has a 2-band equalizer for adjusting the lows or highs on the microphone signal. When the controls are set to “ U ” (unity), the EQ has no effect on the signal.
SP1200 – 22 ADDRESS switch #6 in the Master position (up), and the other unit in the Slave position (down). In this way , you can have one Remote control operate both amplifiers that are assigned to the same zone. Note: The microprocessor polls the AMP ADDRESS switch when it initializes at power -up.
SP1200 – 23 3 0 3 6 9 15 30 55 DIRECT OUTPUT L R INPUT 1 DIGITALL Y CONTROLLED ATTENU ATORS DIGITALL Y CONTROLLED ATTENU ATOR L + — R MACKIE INDUSTRIAL SP1200 BL OCK DIAGRAM (#01.
SP1200 – 24 SP1200 MUSIC CONTROLLER SP1200 Spec ifica tion s P ower Amplifier Sect ion C ont inuous Sine Wav e Avera ge Outpu t P ower, single c hannel driv en: 200 watts into 8 ohms from 20Hz to 20kHz, with no more than 0.01% THD 100V RMS into 50 ohms from 20Hz to 20kHz, with no more than 0.
SP1200 – 25 Disclaimer Mackie Industrial continually engages in research related to product improvement, new materials, and production methods. Design refinements are introduced into existing products without notice as a routine expression of that philosophy .
SP1200 – 26 Appendi x B: Bu tt o n M odes Press 1 on Power Up: AGC Reset • Press and hold the Input 1 button while powering up the SP1200. • Release the Input 1 button and the Input 1 LED blinks. This resets the AGC for all four inputs to the default setting ( – 5 dBu).
SP1200 – 27 MACKIE DESIGNS. ™ RISK OF FIRE! REPLACE WITH FUSE AS MARKED © 2000 ® 055-286-00 REV:__ SP2400:SOFT START R1 C1 C3 R4 R3 R6 D1 F1 J3 J1 J4 J2 J8 J5 J11 J14 J9 J6 J10 J7 J13 J12 D2 JP1.
SP1200 M usi c C o n t roller Mac kie Indus trial 16220 W ood-Red Rd. NE • W oodinville, W A 98072 • USA 888/337-7404 • Outside the U.S.: 425/487-4333 Fax: 425/487-4337 • www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Mackie SP1200 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Mackie SP1200 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Mackie SP1200, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Mackie SP1200 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Mackie SP1200, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Mackie SP1200.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Mackie SP1200. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Mackie SP1200 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
