Manuel d'utilisation / d'entretien du produit 4.1 du fabricant Lucent Technologies
Aller à la page of 363
Lucent Technologies Bell Labs Innovations PARTNER® II Communications System Release 4.1 Programming and Use 518-455-334 Comcode 107879231 Issue 2 August 1996.
Copyright © 1996 Lucent Technologies Lucent Technologies 518-455-334 All Rights Reserved Issue 2 Printed in U.S.A. August 1996 Notice Every effort was made to ensure that the information in this book was complete and accurate at the time of printing.
Contents About This Guide v 1 Overview 1-i Important Safety Instructions 1-ii Features and Capabilities 1-1 System Components 1-2 Auxiliary Equipment 1-10 2 Programming Overview Hardware Consideration.
Contents 4 Using Auxiliary Equipment Overview Answering Machines Call Reporting Devices (SMDR) Credit Card Scanners Fax Machines Modems Night Service with Auxiliary Equipment PARTNER Attendant Voice M.
Contents C FCC and IC Information C-1 D Speed Dial Form D-1 E Programming Mixed Telephone Types E-1 GL Glossary GL-1 IN Index IN-1 Programming Quick References iii.
iv.
About This Guide Purpose This guide is intended for the System Manager. It explains what the PARTNER® II Communications System can do, provides instructions for programming and using the system, and tells you how to get the most out of its many features and capabilities.
■ ■ ■ Using Auxiliary Equipment. The system supports a wide variety of auxiliary equipment, including fax machines, modems, voice messaging systems, and call reporting devices. Chapter 4 provides advice on setting up these devices to work effectively with the system.
Overview 1 Contents Important Safety Instructions Features and Capabilities System Components ■ Control Unit System Modules System Capacity System Mode ■ Telephones System Telephones Intercom Auto.
Important Safety Instructions WARNING: The following list provides basic safety precautions that should always be followed when using your telephone equipment: 1 . 2 . 3 . 4 . 5 . 6 . 7 . 8 . 9 . 10. Read and understand all instructions. Follow all warnings and instructions marked on the product.
Overview 1 Features and Capabilities The following list provides an overview of the system’s features: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Full line of system phones, some with displays showing date, time, and programming and feedback messages. All system phones can provide access to multiple outside lines and system features.
Power failure operation with standard phones, allowing you to make and receive calls during a power failure while retaining programmed equipment settings for up to four days. (An optional Uninterruptible Power Supply, or UPS, is also available to allow full equipment operation during a power failure.
CONTROL UNIT Primary Expansion Carrier Main Circuit Breaker Carrier Main Circuit Breaker or or On/Off Switch 206 Modules On/Off Switch 400 Modules Primary Processor Module Expansion Processor Module G.
Control Unit The control unit is the heart of the system; it is made up of one or two carriers, and it houses the system modules. You can use either the primary carrier, or the primary carrier and the expansion carrier if you need more lines and extensions.
If you are upgrading from a PARTNER or PARTNER Plus system, you can still use its 200E modules, each providing two line jacks. If you want message waiting capability on standard phones that are equipped with message waiting lights, you must connect those phones to extension jacks on Release 3.
Key Mode When the system operates in Key mode, individual outside lines are assigned to users’ extensions for making and receiving calls. At extensions with system phones, each individual line (Line 1, Line 2, Line 3, etc.) assigned to the extension is represented by its own line button.
A major benefit of Hybrid mode is that it allows users who have system phones with fewer buttons to have access to multiple outside lines and various types of pools. You can make efficient use of outside lines by grouping those of a similar type or function together.
Telephones System Telephones This guide refers to Lucent Technologies telephones specifically designed to work with the system as system phones. These include the PARTNER-34D, PARTNER-18D, PARTNER-18, PARTNER-6, MDC 9000, and MDW 9000 telephones.
Intercom Autodialers PARTNER-model system phones support the PARTNER-CA48 Call Assistant Intercom Autodialer at extensions 10 and 11. The autodialer provides Auto Dial buttons for all of the extensions in your system (up to 48). The status lights next to each button indicate calling activity at that extension.
Auxiliary Equipment You can connect many types of telecommunications devices to your system without expensive adapters or additional phone lines. Many industry-standard, single-line devices will work .
Programming 2 Contents Overview Hardware Considerations Initial System Setup ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Setting the System Clock Assigning Lines Key Extensions Pooled Extensions C.
Contents System Programming Options Speed Dialing Dialing Restrictions and Permissions Locking an Extension Restricting Access to Outside Lines or Pools Controlling Calls on Outside Lines or Pools Ove.
Programming 2 Overview After the system hardware is installed, you can customize the system and individual telephones. This chapter explains how to use programming to accomplish that. There are two types of programming: ■ ■ System Programming allows you to customize the system to meet the needs of your business.
Hardware Considerations Programming procedures use line and extension numbers. The line number represents the line jack on a 206 or 400 module to which the outside line is connected. Similarly, the extension number represents the extension jack on a 206 module to which the system phone or standard device is connected.
Initial System Setup After the control unit is installed, you set up the system using a combination of system and telephone programming procedures. In this guide, System Programming procedures are identified by a code (# and three digits); Telephone Programming procedures are identified by the feature name only.
Automatic Line Selection (Centralized Telephone Programming) to specify the order in which the system selects an available line (intercom or outside), when a user at the extension lifts the handset or presses [ Spkr ] to make a call. For extensions with standard phones, set Automatic Line Selection to intercom first.
Customizing Extensions In addition to line or pool assignments, the following procedures can be used to customize an extension: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Line Coverage Extension (#208) to identify an extension as the “owner” of a specific outside line.
Copy Settings The recommended way to set up your system is to program one extension for each type of phone in the system, then use Copy Settings (#399) to program other phones of the same type. For example, you can program one PARTNER-18D phone, then copy its settings to any other extensions that have PARTNER-18D or PARTNER-18 phones.
Pooled Extensions Use this section if your system is configured for Hybrid mode to add new lines to existing pools. To assign a new line to a pooled extension as an individual line, follow the procedures in “Key Extensions” on the previous page.
Changing Settings to Support PBX or Centrex Services This section applies only if you use PBX or Centrex services with your system. If it does not apply, go to the next section, “System Programming Options.” ■ ■ PBX services are provided by a private telephone switch.
System Programming Options This section discusses programming options that involve multiple procedures (such as dialing restrictions and auxiliary equipment settings), as well as features that can be used throughout your system (such as Speed Dialing).
NOTE : If Forced Account Code Entry (#307) is programmed for an extension, that extension is required to enter an account code before dialing an outside —on all of number—even those on the Emergency Phone Number List (#406) the lines or pools assigned to that extension.
Summary Tables 2-1 and 2-2 summarize the available dialing restrictions and permissions, showing how they can be combined in a variety of ways to customize an extension’s dialing privileges.
Setting Up Groups of Extensions You can set up four types of extension groups: ■ ■ ■ ■ ■ ■ ■ ■ Pickup Group Extensions (#501) assigns extensions to one of four Pickup Groups. A Pickup Group lets any user in the system answer calls for any extension in that group.
AA Extensions (#607) identifies extensions to which PARTNER Attendants are connected. This lets the system notify users with display phones when they are receiving a call that has been transferred from the PARTNER Attendant.
– Transfer Return Extension (#306) identifies the extension to which a call transferred by the voice messaging system should be routed if the destination extension does not answer and does not have voice mail coverage active. (The transfer return extension for the voice messaging system is typically extension 10.
PARTNER–34D PARTNER–18D Figure 2-3. Programming Overlays for PARTNER-model Phones Programming 2-15.
During System Programming, the normal functions of several buttons on the display phone at extension 10 or 11 change. For example, the left [ Intercom ] button becomes [ System Program ] and the right [ Intercom ] button becomes [ Central Tel Program ].
PARTNER-34D Phone PARTNER-18D/18 Phone PARTNER-6 Phone Figure 2-4. Button Locations Programming 2-17.
Programming Mode 1 . Place the Programming Overlay over the dialpad of the system display phone at extension 10 or 11—see “The Programming Overlays” earlier in this chapter for more information. 2 . To enter programming mode, press [ Feature ] [ 0 ] [ 0 ].
Changing Programming Type When you are in programming mode, you can move between System Programming and Centralized Telephone Programming. To change to Centralized Telephone Programming when you are in System Programming, press [ Central Tel Program ].
Personal Speed Dialing Personal Speed Dial numbers are outside phone numbers that a user dials by pressing [ Feature ] (or [ # ] on a standard phone) plus a two-digit code. Unlike System Speed Dial numbers, which are available to all users in the system, Personal Speed Dial numbers are available only at the extension for which they are programmed.
Backup Answering Options If you want to program backup answering features to assist the receptionist in handling calls, consider the following features: Automatic System Answer. Useful during peak calling periods to answer outside calls while the receptionist is busy on other calls.
■ ■ Manual Signaling. A Manual Signaling button (labeled MS-Bill) is programmed to signal the target extension. When the button is pressed, the user at the target extension will hear a tone for as long as the button is pressed.
Using Telephone Programming There are two ways to program a telephone: Centralized Telephone Programming from extension 10 or 11 (see below) and Extension Programming from a user’s own extension (see page 2-26).
PARTNER-18D Phone Line/ Programmable Buttons Any unused line button is programmable Figure 2-6. Example of PARTNER-18D phone as a Key Extension PARTNER-6 Phone Line/Pool/ Programmable Buttons Any unused line button is programmable Figure 2-7.
To program a phone from extension 10 or 11, use the following procedure: 1. Place the Programming Overlay over the dialpad of the system display phone at extension 10 or 11—see “The Programming Overlays” earlier in this chapter for more information.
6. To change the settings for another extension, press [ Central Tel Program ], then dial the new extension number. 7. To exit programming mode, you can press [ Feature ] [ 0 ] [ 0 ] or lift the handset off-hook, then place it back in the cradle.
Learning About Telephones 3 Contents System Telephones Buttons and Indicators Lights Ringing Patterns Dial Tones Using the Handset, Speaker, and Microphone Hands-Free Answer on Intercom (HFAI) Voice I.
Learning About Telephones 3 This chapter explains how system and standard phones work with the system, as well as combination extensions where more than one phone or standard device is installed. In addition, basic call handling features and dial-code features are listed at the end of the chapter.
Buttons and Indicators PARTNER-34D Display Programmable Buttons (4 without lights) Line/Pool/Programmable Buttons (32 with lights) Intercom Buttons (2) Message Light Pull-Out Tray for Quick Reference .
PARTNER-6 MDC 9000/MDW 9000 (Handset) Earpiece Volume Line/Pool/Programmable Control Switch Buttons (4) Intercom Buttons (2) Message Light (MDC 9000) or Volume Control (MDW 9000) Line/Pool/ Programmable Buttons (4) MDC 9000: MDW 9000: MDC 9000 (Base) Handset Display Intercom Buttons (2) MDW 9000 (Base) Message Indicator.
Lights Each line or pool button has a green light and a red light. The meaning of these lights varies, depending on whether the button is used to access an outside line or pool, is programmed with a system feature, or is programmed for Auto Dialing an extension number (intercom Auto Dial button).
Table 3-1. Light Patterns for System Phones– Continued Intercom Auto Light Pattern Line Button Pool Button Feature Dial/ Manual Button Signaling Button Wink A call on the line Green wink — — is either on hold means the call is (long on, short off) or parked.
Dial Tones You will encounter two different dial tones when calling with a system phone: Outside dial tone is generated by your local phone company to indicate that you are connected with an outside line. Intercom dial tone is generated by the system to indicate that you are connected with an inside line.
Hands-Free Answer on Intercom (HFAI) When you receive a voice-signaled intercom call, your phone beeps once to indicate that your speaker has been turned on automatically, and you hear the caller’s voice over your phone’s speaker.
Speakerphone Performance Tips The speaker on your system phone has a sensitive sound-activated switch. Room acoustics and background noise can affect the proper operation of the speakerphone.
■ ■ ■ ■ ■ ■ ■ ■ To use a system feature, press [ # ] (in place of [ Feature ] used on system phones) followed by its two-digit code when you hear intercom dial tone. For features that use [ Intercom ] on system phones, dial only the two-digit code when you hear intercom dial tone.
Dial Tones Standard phones have two different dial tones: ■ ■ ■ ■ Outside dial tone is generated by your local telephone company to indicate that you are connected with an outside line. Intercom dial tone is generated by the system to indicate that you are connected with an inside line.
Because there are no line buttons on standard phones, users must use Direct Line Pickup—Idle Line to select a specific idle line. Otherwise, the system selects an idle line automatically when the user dials a 9 at intercom dial tone. (For information on Automatic Line Selection, see Chapter 5.
Combination Extensions A combination extension is an extension with two devices connected to it—either two standard devices, or a system phone and a standard device (but not two system phones). (For instructions on how to install a combination extension, see the PARTNER II Communications System Installation guide.
While on a call on a standard phone, you can use the system phone’s dialpad and fixed-feature buttons to handle calls. For example, you can use the system phone to select a specific outside line or pool, and conduct the call on the standard phone.
Dial-Code Features Dial-code features are features that you access by dialing a feature code at the telephone dialpad. From a system phone, you can press [ Feature ] or [ Intercom ], followed by the t.
Using Auxiliary Equipment 4 Contents Overview 4-1 If a Device Has Trouble 4-3 Answering Machines 4-4 Single Answering Machine 4-5 Multiple Answering Machines 4-6 Personal Answering Machine 4-7 Call Re.
Contents Night Service with Auxiliary Equipment PARTNER Attendant Backup for Receptionist Voice Messaging Systems Delayed Call Handling ■ ■ 4-22 4-24 4-24 4-26 4-26 4-ii.
Using Auxiliary Equipment 4 Overview There are many ways to set up auxiliary equipment—the setup you choose depends upon your needs and the number of devices you have. This chapter presents some common setups. (It does not cover how to physically connect the equipment, or how to program the features.
In addition, you can connect the following devices to your system: ■ ■ ■ ■ ■ ■ ■ Doorphones allow visitors to signal extensions by pressing a button on the doorphone; the person who answers a doorphone call can then speak with the visitor at the doorphone.
Headsets allow users to hold hands-free conversations. A headset is a combination earphone and microphone worn on the head, useful for receptionists, salespeople, or others who need to have their hands free while talking on the phone. Lucent Technologies offers several compatible headsets.
Answering Machines You can use an answering machine to answer calls at night when no one is around, or during business hours when no one can get to the phone.
Single Answering Machine The single answering machine setup (Figure 4-1) serves the entire system. The answering machine is connected to its own extension, and can cover all the lines in the system, or as many lines as you assign to it.
Multiple Answering Machines If a single answering machine cannot handle all your calls, you can set up two or more machines at different extensions (Figure 4-2) so that a call does not go unanswered. If one answering machine is busy, a second call will be answered by the second machine.
Personal Answering Machine A personal answering machine is used to answer all the calls that ring at a certain extension (Figure 4-3). This setup is useful in both Key and Hybrid modes for the followi.
Call Reporting Devices (SMDR) SMDR (Station Message Detail Recording) is a call reporting feature that provides records of call activity. Call reporting information provides you with the ability to: .
Call Reports A call report is a page of information that begins with a header. The header includes field names that describe the information in each call record. The call record is a line of information that includes the fields shown in Figure 4-4. DATE TIME NUMBER DUR.
Station (Extension). This usually is the extension that answered or placed the call. For redirected incoming calls, the last extension on the call is shown on the report, as follows: – For transferred incoming calls: the destination extension. – For transferred outgoing calls: the originating extension.
■ ■ ■ ■ ■ ■ ■ Inside (intercom) calls are not recorded. If you place a call on hold and the caller hangs up, the call is considered complete and the record is sent to the call reporting device. Conference calls appear as two outside calls.
Credit Card Scanners Many retail businesses and restaurants use credit card scanners to get instant approval of credit card purchases. The system allows your credit card scanners to share the lines in your system (as shown in Figure 4-5).
Fax Machines This section suggests several ways you can set up fax machines to work with your system. It includes instructions for programming and using a Fax Management button on a system phone (in o.
Transferring a Call to the Fax Machine There are two situations in which you would want to transfer a call to your fax machine: You answer an outside call and hear a fax machine signaling.
Program the fax machine to dial [ ★ ] [ 7 ] [ 0 ] to make its recorded announcement over your loudspeaker paging system and the speakers of idle system phones in Calling Group 1.
Single Fax Machine The single fax machine setup (shown in Figure 4-6) is good for moderate traffic. The fax machine has its own line (line A), the number of which is published as the fax number. (The fax line can be used by other phones when all other lines are busy.
Fax Line Saver If you do not use your fax machine enough to justify paying for its own outside line, you can put the machine on its own extension. With this setup, you must transfer calls to it manually.
Send and Receive Fax Machines If your business has high-volume fax traffic, you can set up two fax machines, one that only sends and the other that only receives. For example, in Figure 4-8, fax 1 is the send machine, fax 2 is the receive machine. Line A is the fax line, the number of which is published as the fax number.
5. Make sure extension X is not assigned as a Call Waiting (#316) extension, Pickup Group Extension (#501), Calling Group Extension (#502), Night Service Group Extension (#504), or Hunt Group Extension (#505).
Modems There are several ways to use modems with your system, as described below. NOTE : Modems can connect directly to an extension jack without an adapter.
4. Set Automatic Extension Privacy (#304) for extension X to Assigned. 5. Make sure extension X is not assigned as a Call Waiting (#316) extension, Pickup Group Extension (#501), Calling Group Extension (#502), Night Service Group Extension (#504), or Hunt Group Extension (#505).
4 . Set Automatic Extension Privacy (#304) for extension X to Assigned. 5 . Make sure extension X is not assigned as a Call Waiting (#316) extension, Pickup Group Extension (#501), Calling Group Extension (#502), Night Service Group Extension (#504), or Hunt Group Extension (#505).
NOTE: If answering machines are connected to Night Service extensions, you can join a call that was already answered by an answering machine from any system phone. If you have an answering machine with the Call Intercept feature, the answering machine drops off the call when you join it.
PARTNER Attendant The PARTNER Attendant answers calls and directs them to a specified extension, Calling Group, or Hunt Group (based on the digits the caller dials after listening to a list of choices in a recorded greeting).
To Program 1. 2. 3. 4. 5. If your system is configured for Hybrid mode, use Line Access Mode (#313) to change extension X from Pooled to Key. Use Line Assignment (#301) to assign all the lines to extension X that you want the PARTNER Attendant to cover.
Voice Messaging Systems Two voice messaging systems are compatible with your system. You can install one or the other, depending on your business needs: The PARTNER MAIL Voice Messaging System is an auxiliary device that connects to the system through extension jacks.
PARTNER MAIL System Lines Ext. Z1 Ext. Z2 CONTROL Ext. X (not automatically UNIT covered by the PARTNER MAIL Ext.Y System) Ext. 10 Receptionist’s Desk Figure 4-13. Delayed Call Handling To Use Follow the instructions packaged with the PARTNER MAIL system to install it.
7 . Make sure that a Night Service Button (#503) is assigned at extension 10—the receptionist’s extension. When Night Service is on, callers hear the night menu when no one is available to answer their calls.
Feature Reference 5 Contents Overview AA Extensions (#607) Abbreviated Ringing (#305) Account Code Entry (F12) Allowed List Assignments (#408) Allowed Phone Number Lists (#407) Answering Calls Auto Di.
Contents Caller ID Name Display (F16) Calling Group Extensions (#502) Conference Calls Conference Drop (F06) Copy Settings (#399) Dial Mode (#201) Direct Extension Dial Button (#113) Direct Extension .
Contents Hunt Group Extensions (#505) Intercom Dial Tone (#309) Joining Calls Last Number Redial (F05) Line Access Mode (#313) Line Access Restriction (#302) Line Assignment (#301) Line Coverage Exten.
Contents SMDR Output Format (#610) SMDR Record Type (#608) SMDR Talk Time (#611) SMDR Top Of Page (#609) Special Dialing Functions Station Lock (F21) Station Unlock (F22) System Date (#101) System Day.
Feature Reference 5 Overview This chapter provides reference information for programming and using system features. Features are listed in alphabetical order.
This chapter gives step-by-step instructions, using the following conventions: ■ ■ ■ Programming instructions tell you to use the [ Next Data ] button to change values for specific settings. You can, however, enter a value using the dialpad if you prefer.
AA Extensions (#607) Description This System Programming procedure lets you identify extensions where PARTNER Attendants are connected to the system. Doing so lets the system notify users with display phones when they are receiving a call that has been transferred from the PARTNER Attendant.
Abbreviated Ringing (#305) Description This feature applies only to system phones. This System Programming procedure activates or deactivates Abbreviated Ringing at the system phone at a specific extension. When a user is on a call and Abbreviated Ringing is active, any incoming calls ring only once.
Account Code Entry (F12) Description This feature can be used only from a system phone. This feature lets a user enter an account code (up to 16 digits) for an outside call (incoming or outgoing). An account code typically is used to identify a department, project, or client for charge-back or tracking purposes.
■ ■ ■ If a Forced Account Code List exists, you can check to see if an account code is valid when entering or changing an account code by pressing [ Feature ] [ 1 ] [ 2 ] after entering the account code. If the account code is not valid, you will hear denial tone.
To enter or change a forced account code: 1. From a system phone, if a password is programmed for the system, you must enter it before lifting the handset. (See System Password (#403) for more information.) 2 . Lift the handset or press [ Spkr ]. 3 . Press the programmed Account Code Entry button or press [ Feature ] [ 1 ] [ 2 ].
Allowed List Assignments (#408) Description This System Programming procedure lets you assign up to four Allowed Phone Number Lists to specified extensions. Related Features You must use Allowed Phone Number Lists (#407) to create the lists of allowed telephone numbers before you use this procedure.
Allowed Phone Number Lists (#407) Description This System Programming procedure specifies telephone numbers that users can dial regardless of other dialing restrictions, as long as they have access to an outside line.
Examples The examples below show how to enter telephone numbers for an Allowed Phone Number List in Step 4 of “Programming.” When an Allowed List is assigned to an extension, users can dial numbers on that list, even if the numbers would otherwise be restricted.
Description Answering Calls This section describes how users can answer calls ringing at their own extensions. Additional features enable users to pick up calls ringing at other extensions—see “Related Features” below.
How to Answer Calls Ringing at Your Extension System Phone You can answer a call on any line or pool that is ringing, or select a specific line or pool if more than one is ringing: ■ ■ ■ ■ ■ When the telephone is ringing, lift the handset. You are connected to the incoming call.
To answer a coverage call: 1. 2. 3. 1. 2. 3. If your phone is a covering extension and it rings, check your display to see if the ringing call is a coverage call.
Auto Dialing Description Auto Dial buttons can be programmed only on system phones. This Telephone Programming procedure lets system phone users dial outside numbers, extension numbers, feature codes, or account codes with a single touch, by pressing a programmed button.
For PBX or Centrex systems that require a dial-out code to make calls outside the PBX or Centrex system, include the dial-out code followed by one or more pauses (if available) on an Auto Dial button for a number outside the PBX or Centrex system. (See “Changing Settings to Support PBX or Centrex Services” in Chapter 2 for more information.
Using From a system phone, to dial an outside number or extension number (you can lift the handset or press [ Spkr ] first, but you do not have to do so): 1 . If you want to call on a specific line, press the line button (or press [ Intercom ] [ 8 ] and dial the two-digit line number).
Automatic Extension Privacy (#304) Description Related Features This System Programming procedure lets you either allow users to join active calls at an extension or prevent users from joining active calls at an extension. When Automatic Extension Privacy is Assigned for an extension, other users cannot join active calls at that extension.
Programming To change the Automatic Extension Privacy setting for an extension: 1 . Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 0 ] [ 4 ]. 2 . Enter the number of the extension to be programmed. For example, to program extension 16, press [ 1 ] [ 6 ].
Automatic Line Selection Description This Telephone Programming procedure determines the line or pool a user is connected to after lifting the handset or turning on the speaker to make a call. The system looks for lines or pools in the order specified by this procedure and selects the first available line or pool.
Valid Entries Key Extension: Outside lines 01–24, Left Intercom ✔ Examples System Phone Pooled Extension: Pool 880 button 1, button 2, Left Intercom, Right Intercom ✔ Pools 881-883, individual l.
Automatic System Answer Button (#111) Description This feature is available only on the system phone at extension 10. This System Programming procedure identifies a button to be used to turn Automatic System Answer (ASA) on and off. This feature helps the receptionist answer calls during busy periods.
Considerations ■ ■ An Automatic System Answer button must be programmed on a button with lights on the system display phone at extension 10. (This feature will not work if it is programmed on a button without lights.) Automatic System Answer can handle up to three outside calls simultaneously.
Using To turn Automatic System Answer on: Press the Automatic System Answer button at extension 10. The green light is on steady and Automatic System Answer is on. If calls are ringing when Automatic System Answer is turned on, the calls will be answered immediately by the system.
Automatic System Answer Delay (#110) Description This System Programming procedure specifies the number of times (0–9) an incoming call should ring before it is answered by the Automatic System Answer feature.
Automatic System Answer Lines (#204) Description This System Programming procedure identifies the lines on which incoming calls should be answered by the Automatic System Answer feature.
Programming To identify the lines on which outside calls should be answered by the system: 1. 2. 3. 4. 5. 6. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 2 ] [ 0 ] [ 4 ]. Enter the two-digit line number (01–24) of the desired line.
Automatic System Answer Mode (#121) Description This System Programming procedure determines how the system handles Automatic System Answer calls after the greeting plays.
■ ■ If Automatic System Answer Mode is set to Hold or Disconnect, you can intercept a call while the message is playing—the light for the call will be steady red. To intercept the call, press the line button and lift the handset. The message will stop playing when the call is retrieved.
Automatic System Answer Record/Playback (I891) Description This feature lets you record and play back the message that callers hear when a call is answered by the Automatic System Answer feature.
Programming To record an Automatic System Answer message: 1. Turn off Automatic System Answer and Direct Extension Dial and wait for any calls in the process of being answered by these features to be completed. 2. Lift the handset of the system display phone at extension 10 or 11.
To play back an Automatic System Answer message: 1 . Turn off Automatic System Answer and Direct Extension Dial and wait for any calls in the process of being answered by these features to be completed. 2 . Lift the handset of the system display phone at extension 10 or 11.
Automatic VMS Cover (#310) Description This feature applies only if you have a voice messaging system. This System Programming procedure lets you automatically route an extension’s unanswered interc.
Programming To change the Automatic VMS Cover setting for an extension: 1 . Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 1 ] [ 0 ]. 2 . Enter the number of the extension to be covered by the voice messaging system.
Background Music (F19) Description This feature is available only on system phones with speakers. This feature provides background music through the speaker of an idle system phone for a user’s work area. Background Music plays the recorded material from the Music On Hold audio source.
Using To turn Background Music on: 1. From a system phone with a speaker, press the programmed button or press [ Feature ] [ 1 ] [ 9 ]. If the phone is idle, you hear Background Music. If the Background Music button has lights, the green light turns on.
Call Coverage (F20,XX,XX) Description This feature redirects all intercom, transferred, and outside calls on lines assigned ownership from a user’s extension to another system extension (where XX is an extension number from 10–57) for coverage.
If an extension has Call Coverage and Call Forwarding active, calls are routed to the Call Forwarding destination extension (Call Forwarding takes precedence).
Programming To program a Call Coverage button: 1 . Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ Central Tel Program ]. 2 . Enter the number of the extension to be programmed with this feature. 3 . Press a programmable button, preferably a button with lights.
Standard Phone To send your calls for coverage: 1. Lift the handset. You hear intercom dial tone. 2 . Press [ # ] [ 2 ] [ 0 ]. 3 . Dial your extension number. 4 . Dial the extension number of the covering extension. To remove Call Coverage: 1 . Lift the handset.
Call Coverage Rings (#116) Description This System Programming procedure, which applies to all system extensions programmed for Call Coverage, defines the number of times intercom, transferred, and outside calls on lines assigned ownership ring at an extension before they are sent to the covering extension.
Call Forwarding/Call Follow-Me (F11,XX,XX) Description This feature forwards all intercom, transferred, and outside calls from a user’s extension to another system extension (where XX is an extension number from 10–57).
■ If the Call Forwarding feature code and optional originating and destination extensions are programmed on a button with lights, you can use the button to turn Call Forwarding on and off with one touch.
To remove Call Forwarding using the programmed button: 1. Press the programmed button. If an originating extension and a destination extension were programmed on the button, Call Forwarding is deactivated (on a button with lights, the green light is off).
Call Park Description This feature allows you to “park” a call, or put it on a special type of hold, so it can be picked up from any phone in the system.
Standard Phone To park a call: 1 . While on a call, press the switchhook or [ Recall ]. The call is put on hold and you hear intercom dial tone. 2 . Dial your two-digit extension number. 3 . Hang up. If the call is not picked up within three minutes, it rings back at your extension.
Call Pickup (I6XX) Description This feature lets users answer any intercom, outside, or transferred call ringing at another specified extension (where XX is an extension number from 10–57). This feature is useful for officemates who agree to answer each other’s calls.
Call Waiting (#316) Description This feature applies only to standard phones. This System Programming procedure specifies standard phone extensions that are eligible for Call Waiting. Users who receive a call waiting tone hear two beeps when they are on a call to indicate a second incoming intercom, transferred, or outside call.
Caller ID Description Caller ID, also known as Individual Calling Line Identification or ICLID, is available on system display phones on all lines for which you subscribe to Caller ID service. Caller ID information is the caller’s telephone number (or name, if available).
If users Transfer a call, the Caller ID information is passed to the destination extension. If users send calls for Call Coverage, the Caller ID information is not passed to the covering extension. “Coverage Call for XX” appears instead so the user at the covering extension can identify the person for whom the call was originally intended.
Caller ID Inspect (F17) Description This feature allows a user who is active on a call to view Caller ID information for a second call, without disconnecting the current call or putting it on hold.
Using 1. While active on a call, press the programmed button. The green light flutters. Caller ID Inspect is activated. 2. Press a line, pool, or intercom button. The Caller ID or Call Coverage information for the selected line, pool, or intercom displays.
Caller ID Name Display (F16) Description This feature lets users with system display phones toggle the display between Caller ID number and Caller ID name. Caller ID name is an optional feature of the Caller ID service provided by your local telephone company and may not be available in your area (even if Caller ID number is available).
Calling Group Extensions (#502) Description This System Programming procedure identifies the extensions in a Calling Group—a group of extensions that can be called at the same time.
Conference Calls Description This section explains how to set up conference calls using the [ Conf ] button on a system phone or the switchhook on a standard phone. A conference call connects up to five parties (including the conference originator) in a single call.
Using System Phone 1. Set up the call to the first party. (You can call the party, pick up the call from hold, or answer an incoming call.) You are connected with the first party. 2. Press [ Conf ]. The first party is now on hold. 3 . Set up the call to the second party.
Conference Drop (F06) Description This feature drops the last outside party added to a conference call, without disconnecting the other parties. Related Features ■ ■ For instructions on setting up conference calls, see Conference Calls. You can use Outside Conference Denial (#109) to disallow conference calls with multiple outside parties.
Copy Settings (#399) Description This System Programming procedure copies all of the following settings from one extension to another: #301 Line Assignment #302 Line Access Restriction #303 Display La.
Dial Mode (#201) Description This System Programming procedure identifies individual lines as touch-tone or rotary. You should check with your local phone company if you are not sure which type of line is being provided to you.
Direct Extension Dial Button (#113) Description This feature is available only on the system phone at extension 10. This System Programming procedure identifies a button to be used to turn Direct Extension Dial (DXD) on and off. This feature permits an outside caller to dial an extension or Hunt Group directly, without the aid of the receptionist.
Considerations ■ ■ ■ ■ ■ It is recommended that you use only one automated answering option for incoming calls (either this feature, the Automated Attendant Service of the voice messaging system, or a PARTNER Attendant). Direct Extension Dial does not transfer calls to Calling Groups.
Using To turn Direct Extension Dial on: Press the Direct Extension Dial button at extension 10. The green light is on steady and Direct Extension Dial is on. If calls are ringing when Direct Extension Dial is turned on, the calls will be answered immediately by the system.
Direct Extension Dial Delay (#112) Description This System Programming procedure specifies the number of times (0–9) an incoming call should ring before it is answered by the Direct Extension Dial feature.
Direct Extension Dial Lines (#205) Description This System Programming procedure identifies the lines on which incoming calls are to be answered for Direct Extension Dial. Related Features ■ ■ ■ ■ You must program a button on the system display phone at extension 10 to turn Direct Extension Dial on and off.
Programming To identify the lines on which outside calls should be answered for Direct Extension Dial: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 2 ] [ 0 ] [ 5 ]. 2. Enter the desired line number (01–24). For example, to specify line 1, press [ 0 ] [ 1 ].
Direct Extension Dial Record/Playback (I892) Description This feature lets you record and play back the message that callers hear when a call is answered by the Direct Extension Dial feature.
If a message was previously recorded, a display similar to the following appears: DXD: 1=Record 2=Play 5. Press [ 1 ]. A display similar to the following appears for three seconds: Record at the tone After three seconds, you hear a tone and you can begin recording your message.
Direct Line Pickup—Active Line (I68LL) Description This feature allows users to access a ringing or held call, or to join a call in progress on a specific outside line (where LL is a line number from 01–24). This feature is useful for picking up a ringing or held call or for joining a call on a line that is not assigned to the phone.
Using System Phone 1. If you want, lift the handset. 2. Press a button programmed with Direct Line Pickup—Active Line, then dial the two-digit line number (01–24) of the line you want to pick up or join; or dial [ Intercom ] [ 6 ] [ 8 ] and the two-digit line number.
Direct Line Pickup—Idle Line (I8LL) Description This feature allows users to access a specific outside line (where LL is a line number from 01–24) when the line is not in use. This feature is useful for accessing a line that is not assigned to the phone.
Disallowed List Assignments (#405) Description This System Programming procedure lets you assign up to four Disallowed Phone Number Lists to specified extensions. Related Features You must use Disallowed Phone Number Lists (#404) to create the lists of disallowed telephone numbers before you use this procedure.
Disallowed Phone Number Lists (#404) Description This System Programming procedure specifies telephone numbers that users cannot dial. For example, you may want to prevent calls to a specific telephone number or to categories of numbers, such as international numbers.
Examples The examples below show how to enter telephone numbers for a Disallowed Phone Number List in Step 4 of “Programming.” Specific Telephone Numbers. Enter the phone number exactly as you would dial it. For example, to prevent calls to the local number 555-5678, press [ 5 ] [ 5 ] [ 5 ] [ 5 ] [ 6 ] [ 7 ] [ 8 ].
Programming To create a list of Disallowed Phone Numbers: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 4 ] [ 0 ] [ 4 ]. 2. At the List Number: prompt, identify the list to be set up (1–4). For example, to select the first list, press [ 1 ].
Display Description PARTNER-model display phones have a 2-line, 24-character (per line) adjustable display area, for calling and programming feedback. Specifically, the display shows: ■ ■ ■ ■ .
Related Features ■ The System Date (#101), System Day (#102), and System Time (#103) settings are shown as the default display. ■ You can use Display Language (#303) to identify the language in which messages appear, if the extension has a system display phone.
Display Language (#303) Description This System Programming procedure identifies the language in which display messages appear if the extension has a system display phone. The language is set for each extension, so phones in the same system can display different languages.
Distinctive Ring (#308) Description This System Programming procedure determines whether calls should ring at a standard device using the system’s distinctive ringing patterns—different patterns for outside, intercom, and transferred calls—or whether all calls to the standard device should ring like outside calls.
Do Not Disturb (F01) Description Related Features This feature is available only on system phones. This feature lets a system phone user press a programmed button to prevent incoming calls for the extension from audibly alerting (lights still flash). When Do Not Disturb is on, outside callers hear ringing while inside callers hear a busy signal.
Programming To program a Do Not Disturb button: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ Central Tel Program ]. 2. Enter the number of the extension to be programmed with this feature. 3. Press a programmable button with lights.
Doorphone Alert Extensions (#606) Description This System Programming procedure identifies up to 48 extensions that are to signal when a doorphone button is pressed.
Doorphone Extension (#604 and #605) Description These System Programming procedures identify extensions to which doorphones are connected. A doorphone is usually placed near an entrance, to screen visitors.
Emergency Phone Number List (#406) Description This System Programming procedure creates a list of up to 10 telephone numbers that all users can dial regardless of dialing restrictions provided they have access to an outside line. Typical list entries include fire, police, and other emergency services numbers.
Programming To create an Emergency Phone Number List: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 4 ] [ 0 ] [ 6 ]. 2. Select a list entry (01–10). For example, to select the third entry, press [ 0 ] [ 3 ]. A display similar to the following appears: Emergency List 03 Data ----------- 3.
Exclusive Hold (F02) Description This feature is available only on system phones. This feature prevents other extensions from picking up outside calls placed on hold at a specific extension with a system phone. Related Features ■ You can use the Hold button to put calls on regular hold (any extension can pick up the held call).
Extension Name Display Description Users can assign a name to their extension: up to 20 characters long on PARTNER-model phones, up to 12 characters on MLS-model phones. Then, when that extension is used to make an intercom, group, or transferred call, the name appears on the system display phone receiving the call.
Programming To assign a name to an extension: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ Central Tel Program ]. 2. Enter the number of the extension to be programmed. For example, to program extension 12, press [ 1 ] [ 2 ].
External Hotline (#311) Description This procedure applies only to standard phones. This System Programming procedure identifies an external hotline extension. When a user lifts the handset of an external hotline, a predetermined outside number is dialed automatically.
Valid Entries Extensions 11–15, 17–21, 23–27, 29–33, 35–39, 41–45, 47–51, and 53–57 1 = Assigned 2 = Not Assigned ✔ Programming To identify an external hotline extension: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 1 ] [ 1 ].
Fax Machine Extensions (#601) Description This System Programming procedure identifies extensions to which fax machines are connected. Related Features ■ ■ If you want to monitor fax machine statu.
Forced Account Code Entry (#307) Description This feature applies only to system phones. This System Programming procedure identifies specific extensions at which users must enter an account code prior to making outside calls.
Valid Entries 1 = Assigned 2 = Not Assigned ✔ Programming To program an extension for Forced Account Code Entry: 1. 2. 3. 4. 5. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 0 ] [ 7 ]. At the Extension: prompt, enter the number of the extension to be programmed.
Forced Account Code List (#409) Description This System Programming procedure lets you identify a list of up to 99 account code verification entries for extensions that are forced to enter account codes.
■ Wildcard Characters. You can use wildcard characters in list entries. For example, your company’s Sales Department has a three digit account code—the first digit represents the department and the second and third digit represent the individuals in the department.
Group Call Distribution (#206) Description This System Programming procedure assigns outside lines to Hunt Groups. Doing so allows outside calls to ring directly into a Hunt Group instead of being answered and transferred by the receptionist. You can assign lines to Hunt Groups 1–7.
■ If you install a voice messaging system, assign the system extensions associated with the voice messaging system hardware to Hunt Group 7. Then, use this procedure to assign outside lines to Hunt Group 7 for Automated Attendant Service.
Group Calling—Ring/Page (I7G/I*7G) ■ ■ Description Related Features This feature lets users ring, page, or transfer calls simultaneously to all of the extensions in any one of four Calling Groups (G is a Calling Group number from 1–4).
For example, a car dealership puts all extensions for the sales staff into Calling Group 1. To let a prospective customer talk to any salesperson, the receptionist simply transfers the call to the group by dialing [ Transfr ] [ 7 ] [ 1 ]. All phones in Calling Group 1 ring, and the customer is connected to the first salesperson to answer.
To manually ring or page a Calling Group: 1. Lift the handset and press [ Intercom ]. You hear intercom dial tone. 2. To make a ringing call, dial [ 7 ] and a group number (1–4). All available extensions in the Calling Group ring. To make a paging call, press [ ★ ] [ 7 ] and a group number (1–4).
Group Hunting—Ring/Voice Signal (I77G/I*77G) Description This feature lets you distribute call volume among extensions in a group, to offload call activity from a single user.
■ ■ You can program a Group Hunting button on a system phone to ring or voice signal a specified Hunt Group with one touch. If you have a voice messaging system, you can program Hunt Group 7 ([ Intercom ] [ 7 ] [ 7 ] [ 7 ]) on a button to retrieve messages with one touch.
To manually ring or voice signal a Hunt Group: 1. Lift the handset and press [ Intercom ]. You hear intercom dial tone. 2 . To make a ringing call, dial [ 7 ] [ 7 ] and a group number (1–7). The next available extension in the Hunt Group rings. If no one answers within three rings, the call hunts to the next available extension.
Group Pickup (I66G) Description This feature allows a user at any extension in the system to answer any outside, intercom, or transferred call ringing at an extension in a Pickup Group (where G is a Pickup Group number from 1–4).
Using System Phone To use Group Pickup when programmed on a button, press the programmed button. To use manually: 1. Lift the handset and press [ Intercom ]. You hear intercom dial tone. 2. Dial [ 6 ] [ 6 ] and a group number (1–4) to pick up a call ringing at any extension in the group.
Hold Description This section explains how to place and retrieve calls on hold, using either the [ Hold ] button on a system phone or the switchhook on a standard phone. (The user can make and receive other calls on another line or pool while a call is on hold.
Using System Phone To put a call on hold, press [ Hold ]. The green light next to the [ Intercom ], line, or pool button winks. To retrieve a call that you put on hold: 1. Press the [ Intercom ], line, or pool button next to the winking green light. 2.
Hold Disconnect Time (#203) Description This System Programming procedure lets you change the hold disconnect time for an outside line. When a caller on hold hangs up, the local telephone company may send a special signal to the system to free the line.
Hotline (#603) Description This System Programming procedure identifies an internal hotline extension and its alert extension. When a user lifts the handset of the hotline phone, the alert extension rings. You can set up several hotline and alert extension pairs.
Programming To identify a hotline extension and its alert extension: 1. 2. 3. 4. 5. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 6 ] [ 0 ] [ 3 ]. At the Extension: prompt, enter the hotline extension number—see “Valid Entries” on the previous page.
Hunt Group Extensions (#505) Description This System Programming procedure lets you assign any number of extensions to a Hunt Group. The system supports up to seven Hunt Groups; however, Hunt Group 7 is used exclusively for the voice messaging system.
Considerations for Hunt Group 7 This Hunt Group is used exclusively for the extensions associated with the voice messaging system hardware. Do not assign any other extensions to this group.
Intercom Dial Tone (#309) Description This System Programming procedure determines the type of dial tone that the system provides at an extension. It may be necessary to change this setting to Machine (outside line) dial tone for an autodialing device, such as a fax or modem, that has trouble making calls.
Joining Calls Description Joining is adding yourself to a call in progress, the same way you do on a home telephone by picking up an extension. (This is different from conferencing, in which the originator “pulls you into” the call.
How to Join a Call System Phone A steady red light next to a line button indicates a call is in progress at another extension. To join a call: ■ ■ Press the line button next to the steady red light and lift the handset, or Lift the handset and press [ Intercom ] [ 6 ] [ 8 ] and the two-digit line number.
Last Number Redial (F05) Description This feature redials the last outside number dialed (maximum 28 digits). It is useful for immediately redialing a busy number. Related Features You can use Save Number Redial to temporarily save the last number dialed.
Line Access Mode (#313) Description This procedure applies only to systems configured for Hybrid mode. This System Programming procedure identifies individual extensions that are to operate as key extensions even though the system is configured for Hybrid mode.
Line Access Restriction (#302) Description This System Programming procedure restricts an extension from receiving and/or making outside calls on specific lines.
Programming To restrict an extension from making calls on a specific line: 1. 2. 3. 4. 5. 6. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 0 ] [ 2 ]. At the Extension: prompt, enter the number of the extension to be programmed.
Line Assignment (#301) Description This procedure applies to key extensions or to individual lines on pooled extensions. This System Programming procedure assigns the outside lines that are available at an extension.
PARTNER-34D PARTNER-18D/PARTNER-18 PARTNER-6 Figure 5-1. Default Line Assignments Line Assignment (#301) 5-119.
Considerations ■ ■ ■ ■ You cannot assign a line that belongs to a pool as an individual line on that pooled extension. A line must be assigned to a button with lights. If a line is assigned to a button without lights, you cannot access that line, nor can you program anything else on the button.
4. At this point: ■ ■ ■ ■ ■ If you want to assign the line to the first available button with lights, press [ Next Data ] until a display similar to the following appears: Line Assignment 15.
Line Coverage Extension (#208) Description This System Programming procedure identifies an extension as the “owner” of a specific outside line, so the extension can activate Call Coverage or VMS Cover for that line.
Programming To change the Line Coverage setting for an extension: 1. 2. 3. 4. 5. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 2 ] [ 0 ] [ 8 ]. Enter the desired line number. For example, to program line 24, press [ 2 ] [ 4 ].
Line Ringing Description This Telephone Programming procedure determines how each outside line or pool assigned to an extension rings. A line or pool can ring immediately, ring with a 20 second delay, or not ring at all. Delayed Ring is useful for backup coverage on shared lines or pools, such as for secretaries who cover each other’s lines.
Examples ■ ■ Receptionist Call Routing. If you want calls to be answered by the receptionist first, set the lines at the receptionist’s extension to Immediate Ring and the lines at the users’ extensions to No Ring. (This is the factory setting for Hybrid mode.
Loudspeaker Paging (I70) Description This feature accesses the loudspeaker paging system, if you have one connected to the system through the PAGE jack on the primary processor module.
Standard Phone To make an announcement over the loudspeaker paging system: 1. Lift the handset. You hear intercom dial tone. 2. Dial [ 7 ] [ 0 ]. 3. Speak into the handset.
Making Calls Description A user can make a call by dialing an outside phone number or an extension number. There are also several ways to “speed dial” a number—see “Related Features” below.
If dialing restrictions are programmed for an extension, the system may prevent a user at that extension from placing certain calls. For example, a user may not be allowed to dial 900 numbers from the extension. (Or an extension may be programmed to take incoming calls only, so the user cannot dial out at all.
To make an outside call using a specific pool: 1. Press the idle pool button (red and green lights are both off) or press [ Intercom ] plus the three-digit pool access code (880, 881, 882, or 883). 2. If desired, lift the handset. 3. Dial the phone number.
System Phone You can lift the handset or press [ Spkr ] before dialing, then: 1. Press an idle [ Intercom ] button (red and green lights are both off).
Manual Signaling (F13XX or F13*XX) Description This feature applies only to PARTNER- and MLS-model phones. This feature lets you program a button on your PARTNER- or MLS-model phone that you can use to signal a predetermined co-worker’s extension. It typically is used by a receptionist to alert a user when the user is busy on another call.
Programming To program a Manual Signaling button: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ Central Tel Program ]. 2. Enter the number of the extension to be programmed with this feature. 3. Press a programmable button. 4.
Message Light Off (F10XX) Description This feature turns off the message light at a specified extension (where XX is an extension number from 10–57).
Using System Phone To turn off the message light: 1. Press the programmed button or press [ Feature ] [ 1 ] [ 0 ]. If you programmed the destination extension number on the button, the message light for the destination extension goes off. Skip Step 2.
Message Light On (F09XX) Description This feature turns on the message light at a specified extension (where XX is an extension number from 10–57). Related Features For instructions on turning off the message light, see Message Light Off. You may be able to use this feature to signal someone at a doorphone extension.
Using System Phone To turn on the message light: 1. Press the programmed button or press [ Feature ] [ 0 ] [ 9 ]. If you programmed the destination extension number on the button, the message light for the destination extension goes on. Skip Step 2. 2.
Music On Hold (#602) Description This System Programming procedure activates or deactivates the MUSIC ON HOLD jack on the primary processor module. The jack must be active and an audio source must be connected to the jack in order to provide recorded music or messages to callers on hold.
Valid Entries 1 = Active ✔ 2 = Not Active Programming To change the setting of the MUSIC ON HOLD jack: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 6 ] [ 0 ] [ 2 ]. 2. To activate or deactivate the MUSIC ON HOLD jack, press [ Next Data ] until the appropriate value displays.
Night Service Button (#503) Description This System Programming procedure identifies a button on the system phone at extension 10 to be used to turn Night Service on and off.
Programming To program a Night Service button at extension 10: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 5 ] [ 0 ] [ 3 ].
Night Service Group Extensions (#504) Description This System Programming procedure assigns extensions to the Night Service Group. When Night Service is on and a call comes in, all extensions in the Night Service Group ring immediately, regardless of normal Line Ringing settings.
Number of Lines (#104) Description This System Programming procedure determines in Key mode the number of outside lines that are automatically assigned to all system extensions; in Hybrid mode, it determines the number of lines assigned to the main pool.
Outgoing Call Restriction (#401) Description This System Programming procedure identifies the types of outgoing calls that can be made on all lines at an extension. See “Dialing Restrictions and Permissions” in Chapter 2 for a summary of calling restrictions.
Programming To identify the types of outgoing calls that can be made on all lines at an extension: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 4 ] [ 0 ] [ 1 ]. 2. At the Extension: prompt, enter the number of the extension to be programmed.
Outgoing Call Restriction Button (#114) Description This System Programming procedure identifies a button on the system phone at extension 10 to be used to change the current Outgoing Call Restriction setting for an extension. This button is useful for quickly changing an extension’s restriction.
Programming To program an Outgoing Call Restriction button at extension 10: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 1 ] [ 1 ] [ 4 ].
Outside Conference Denial (#109) Description This System Programming procedure determines whether users can include more than one outside party in a conference call. Related Features For instructions on making conference calls, see Conference Calls. Use Conference Drop to drop the last outside party added to the conference.
Personal Speed Dial Numbers Description This Telephone Programming procedure lets you store up to 20 frequently dialed numbers for each extension. A Personal Speed Dial number can be dialed quickly by pressing [ Feature ] (or [ # ] at intercom dial tone on a standard phone) and the two-digit code from 80 through 99.
Programming To program Personal Speed Dial numbers: 1. 2. 3. 4. 5. 6. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ Central Tel Program ]. Dial the number of the extension to be programmed with this feature. Select a two-digit code by pressing [ Feature ] and dialing two digits between 80 and 99.
Pickup Group Extensions (#501) Description This System Programming procedure lets you assign extensions to a Pickup Group. When a call rings at an extension in a Pickup Group, a user at any other extension in the system can answer the ringing call by dialing the Pickup Group code.
Pool Access Restriction (#315) Description This procedure applies only to pooled extensions in Hybrid mode. This System Programming procedure restricts a pooled extension from receiving and/or making outside calls on all lines belonging to a specific pool.
Programming To restrict an extension from making or receiving calls on all the lines in a specific pool: 1. 2. 3. 4. 5. 6. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 1 ] [ 5 ]. Enter the number of the extension to be programmed.
Pool Extension Assignment (#314) Description This feature applies only to pooled extensions in Hybrid mode. This System Programming procedure identifies the pools that are assigned to buttons at a pooled extension. The system uses two buttons to represent the main pool (880) and one for each auxiliary pool (881, 882, 883).
Considerations ■ You cannot assign pool buttons to extension 10 or to any key extension. ■ The main pool buttons are always assigned to the two leftmost buttons on the bottom row of a system phone. You cannot use Select Button (Setting 3) for the main pool (880) during Pool Extension Assignment programming.
4. At this point: ■ If you want to assign the pool to the first available button with lights, press [ Next Data ] until a display similar to the following appears: Pool Ext Assign 15 P881 1 Assigned.
Pool Line Assignment (#207) Description This procedure applies only to systems configured for Hybrid mode. This System Programming procedure assigns lines to or removes lines from the main and auxiliary pools supported for Hybrid mode. You can change line assignments in the main pool (880) or in any of three auxiliary pools (881, 882, or 883).
Programming To change the assignment of lines to pools: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 2 ] [ 0 ] [ 7 ]. 2. Enter the first line to be programmed. For example, to program line 8, press [ 0 ] [ 8 ]. A display similar to the following appears: Lines to Pools L08 2 Pool 880 3.
Privacy (F07) Description This feature is available only on system phones. This feature lets system phone users press a programmed button to turn Privacy on and off, preventing or allowing other users to join calls at the user’s extension as needed.
Recall (F03) Description This feature causes the system to send a timed switchhook flash over the telephone line to “recall” a new dial tone or to access a PBX, central office, or Centrex feature, such as Call Waiting.
Using To access a PBX, central office, or Centrex feature (such as Call Waiting) while active on an outside line: System Phone 1. Press the programmed button or press [ Feature ] [ 0 ] [ 3 ].
Recall Timer Duration (#107) Description This System Programming procedure lets you change the length of the timed signal, or switchhook flash, generated by the system Recall feature (as well as by the Recall option used in Auto Dial and Speed Dial numbers).
Ring on Transfer (#119) Description This System Programming procedure lets you specify what callers hear while they are being transferred. If Ring on Transfer is set to Active, callers hear ringing as.
Rotary Dialing Timeout (#108) Description This System Programming procedure changes the length of the Rotary Dialing Timeout. You may need to change the length of the timeout if you have any rotary lines and you are having trouble calling out on standard touch-tone phones.
Save Number Redial (F04) Description This feature is available only on system phones. This feature saves into temporary memory the last outside number (up to 28 digits) dialed from an extension with a system phone. Users can use this feature to save a number before they hang up on a busy or non-answering call.
Send All Calls Description You can use the Call Coverage, VMS Cover, or Do Not Disturb buttons to send intercom and transferred calls and outside calls on owned lines immediately either to the covering extension or to your voice mailbox.
Simultaneous Paging ( I*70) Description This feature accesses the loudspeaker paging system, if you have one connected to the system through the PAGE jack on the primary processor module, and all of the idle system phones with speakers assigned to Calling Group 1.
Standard Phone To make an announcement over the loudspeaker paging system and the idle system phones with speakers in Calling Group 1: 1. Lift the handset.
SMDR Output Format (#610) Description Call reporting (often referred to as Station Message Detail Recording or SMDR) provides detailed tracking of telephone usage in a printed report.
SMDR Record Type (#608) Description Call reporting (often referred to as Station Message Detail Recording or SMDR) provides detailed tracking of telephone usage in a printed report. This System Programming procedure allows you to specify whether all calls or outgoing calls only are to be included on call reports.
SMDR Talk Time (#611) Description Call reporting (often referred to as Station Message Detail Recording or SMDR) provides detailed tracking of telephone usage in a printed report. This System Programming procedure allows you to indicate whether or not you want to include a Talk field on call reports.
SMDR Top Of Page (#609) Description Call reporting (often referred to as Station Message Detail Recording or SMDR) provides detailed tracking of telephone usage in a printed report. This System Programming procedure notifies the system that the printer has been aligned to the top of a new page.
Special Dialing Functions Description This feature lets you add special characters for System Speed Dial numbers, Personal Speed Dial numbers, and Auto Dial numbers, as follows: Function Button Pause [ Hold ] Recall [ Spkr ] Stop [ Mic/HFAI ] Touch-Tone [ Transfr ] Enable Considerations Display Description P Inserts a 1.
■ Stop. Your local bank-by-phone service requires that you enter a password before the account number. To program a Personal Speed Dial number or an Auto Dial button to call the bank at 555-7898, in.
Station Lock (F21) Description This feature is available only on system and standard touch-tone phones. This feature lets users enter a four-digit code on their telephone dial pad to “lock” their extension. Later, the user enters the identical code to unlock the extension.
If the code entered in Step 3 matches the code entered in Step 2, the extension is locked. On a button with lights, the green light changes to on steady. On a display phone, the display shows ****. If the code entered in Step 3 does not match the code entered in Step 2, the extension remains unlocked.
Station Unlock (F22) Description This feature is available only at extension 10 or 11. This feature lets you unlock a specific user’s locked extension. Use this feature when a user forgets the code he or she used to lock the extension. Related Features Use Station Lock to lock an extension.
System Date (#101) Description This System Programming procedure sets the month, day, and year. The system displays only the month and day on display phones when the phone is idle; the month, day, and year print on SMDR call reports. Considerations Include leading zeros for single-digit months or days.
System Day (#102) Description This System Programming procedure sets the day of the week that appears on system display phones. Valid Entries 1 = Sunday ✔ 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday Programming To change the System Day: 1.
System Password (#403) Description This feature is available only on PARTNER- and MLS-model phones. This System Programming procedure defines a four-digit password that users can enter from PARTNER- and MLS-model phones to override dialing restrictions (if the extension has access to an outside line).
System Reset—Programming Saved (#728) Description This System Programming procedure resets the system while retaining the currently programmed settings.
System Speed Dial Numbers Description This feature lets you program a list of up to 100 frequently dialed numbers for the system. Anyone on the system can dial a System Speed Dial number by pressing [ Feature ] (or [ # ] at intercom dial tone on a standard phone) and the three-digit code from 600 through 699.
Valid Entries Any phone number—up to 28 characters consisting of the digits 0–9, [ ★ ], [ # ], and special dialing functions that you can access by pressing [ Hold ] (Pause), [ Mic/HFAI ] (Stop).
Using System Phone You can lift the handset or press [ Spkr ] before dialing: 1. If you want to call on a specific line, press the line button (or press [ Intercom ] [ 8 ] and the two-digit line number).
System Time (#103) Description This System Programming procedure sets the time that appears on system display phones. Considerations ■ Enter the time in 24-hour notation. In this scheme, the hours of the day are 0000 (12 midnight) to 2359 (11:59 p.m.
Toll Call Prefix (#402) Description This System Programming procedure indicates whether users must dial a 0 or 1 before the area code to make a long-distance call, or just the area code and number. This feature should be set to reflect the dialing patterns of your local telephone company.
Touch-Tone Enable (F08) Description This feature is available only on system phones. This feature lets a system phone user send touch-tone signals on an outside call over a rotary line. For example, a user may need to dial touch-tone digits while on a call to a bank-by-phone service.
Transferring Calls Description This section explains how to transfer calls using the [ Transfr ] button on a system phone or the switchhook on a standard phone. Transferring a call lets users “pass” a call from one extension to another. Users can transfer both outside calls and intercom calls to other extensions.
■ Calls can be transferred to Calling Groups and Hunt Groups. ■ When you transfer a call from a display phone, the number to which you are transferring the call briefly appears on the display. If a transferred call is unanswered, the number of the extension that is returning the transferred call also appears on display phones.
■ To make a voice-signaled transfer to a system phone, in Step 2 of the procedure on the previous page press [ ★ ] plus the two-digit extension number. Then listen for one of the following responses: – If you hear one beep, you have reached an idle system phone.
Standard Phone ■ To pass a call to another extension: 1. While on a call, press the switchhook down once rapidly. You hear intercom dial tone. 2. Dial the extension number (or [ 7 ] [ 7 ] and a Hunt Group number or [ 7 ] and a Calling Group number) to which you want the call transferred.
Transfer Return Extension (#306) Description By default, transferred calls return to the originating extension if they are not answered. This System Programming procedure can be used to identify a different return extension for the extension that transfers a call.
Programming To change the Transfer Return Extension for a specific extension: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 0 ] [ 6 ]. 2. Dial the number of the originating extension. 3. Dial the number of the extension to which the call should return if it is not answered.
Transfer Return Rings (#105) Description This System Programming procedure, which applies to all system extensions, defines the number of times a transferred call rings before it goes to the transfer return extension. Related Features ■ ■ ■ ■ By default, transferred calls return to the originating extension if they are not answered.
VMS Cover (F15) Description Related Features This feature applies only if you have a voice messaging system. It is available only on system phones. This feature lets system phone users press a program.
Programming To program a VMS Cover button: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ Central Tel Program ]. 2. Enter the number of the extension to be programmed with this feature. 3. Press a programmable button with lights.
VMS Cover Rings (#117) Description This feature applies only if you have a voice messaging system. This System Programming procedure, which applies to all system extensions programmed for VMS Cover, defines the number of times a call rings before it is sent to a user’s voice mailbox.
VMS Hunt Delay (#506) Description This feature applies only if you have a voice messaging system. This System Programming procedure determines when outside calls should be answered by the Automated Attendant Service of the voice messaging system.
VMS Hunt Schedule (#507) Description This feature applies only if you have a voice messaging system. This System Programming procedure determines whether the outside lines assigned to Hunt Group 7 hunt through the VMS Hunt Group all the time, only during Day operation (Night Service is off), or only during Night operation (Night Service is on).
Voice Interrupt On Busy (#312) Description Related Features This feature is available only on system phones. This System Programming procedure identifies extensions that can receive voice interrupt on busy calls.
Valid Entries 1 = Assigned 2 = Not Assigned ✔ Programming To change the Voice Interrupt On Busy setting for an extension: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 3 ] [ 1 ] [ 2 ]. 2. Enter the number of the extension to be programmed with this feature.
Voice Interrupt On Busy Talk-Back (F18) Description This feature is available only on system phones. This feature lets you program a button that is used to respond to a voice interrupt on busy call while the user is active on another call.
Voice Mailbox Transfer (F14) Description Related Features This feature applies only if you have a voice messaging system. It is available only on system phones. This feature lets a system phone user transfer a caller directly to a specific extension’s voice mailbox, in order for the caller to leave a message without first ringing the extension.
Wake Up Service Button (#115) Description This System Programming procedure identifies a button on the system phone at extension 10 to be used for scheduling wake up (or reminder) calls for system extensions. When a wake up call is scheduled, the system makes an intercom call to the target extension at the scheduled time.
Programming To program a Wake Up Service button at extension 10: 1. Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 1 ] [ 1 ] [ 5 ].
To review a scheduled wake up time for a specific extension: 1. Press the Wake Up Service button at extension 10. 2. Dial the two-digit target extension number (or use an Auto Dial button). 3. Review the displayed wake up time and target extension number.
Troubleshooting 6 Contents When You Need Help 6-1 Power Failure Operation 6-1 Problems with System Phones 6-2 ■ ■ ■ ■ ■ ■ ■ System Phone Does Not Ring 6-2 System Phone Does Not Work 6-3 .
Contents Problems with Auxiliary Equipment 6-14 ■ Standard Device Does Not Answer 6-14 ■ Standard Device Does Not Dial Out Properly 6-14 ■ Poor Transmission Quality on Modem 6-14 ■ Call Record.
Troubleshooting 6 When You Need Help If you have a problem with your system, you may be able to solve it by following the appropriate troubleshooting procedures described in this chapter. If not, you can call for help: in the continental U.S., call the hotline at 1 800 628-2888; outside the continental U.
The system can stay programmed for approximately four days after it stops receiving power. After four days elapse, all of the system’s programmed settings return to the factory settings.
System Phone Does Not Work Possible Cause 1: Telephone cord is plugged into wrong jack on bottom of system phone. What to do: Plug the modular telephone cord into the correct jack—see the PARTNER II Communications System Installation guide for instructions.
Display Shows Only 16 Characters Per Line Possible Cause: Processor module is not R 4.1. What to do: Check the release number on the processor module. ■ If the processor module release number is lower than 4.1, the display shows a maximum of 16 characters per line.
Some Caller ID Information Does Not Display Possible Cause: Not all calls on Caller ID lines will be displayed. This varies by local phone company. What to do: If Caller ID information for a large number of calls is not displayed, contact your local telephone company.
Problems with Standard Phones Standard Phone Does Not Ring Possible Cause 1: Ringer is turned off. What to do: Turn on the ringer ■ If the phone rings, the problem is solved. ■ If the phone still does not ring, go to Possible Cause 2. Possible Cause 2: Call Forwarding is turned on.
Standard Phone Rings Back After Intercom Call with No One at Other End Possible Cause 1: The switchhook is accidentally pressed and released, causing a call to ring back. What to do: Be sure that the handset is always replaced carefully. If the problem is not solved, go to Possible Cause 2.
Other Problems with Phones Trouble Making Outside Calls Trouble making outside calls could be one of the following: ■ You hear a dial tone, but the dial tone continues as you try to dial. ■ You hear a dial tone, which cuts off when you dial, but the line does not ring.
Possible Cause 5: Local phone company is not accurately receiving the dialing signals. What to do: Isolate the problem. Use the telephone to make calls on different lines.
Possible Cause 1: Forced Account Code Entry is assigned to the extension. What to do: Find out if Forced Account Code Entry (#307) is assigned to the extension. If it is, enter a valid account code. ■ If you can make a call, the problem is solved. ■ If Forced Account Code Entry is not assigned, go to Possible Cause 2.
Possible Cause 6: One or more local phone company lines in the pool are faulty. What to do: At extension 10, try to access each individual line assigned to the pool. ■ If the lines accessed from individual line buttons on extension 10 are still faulty, refer to Possible Cause 7 in “Other Problems with Phones: Trouble Making Outside Calls.
Trouble Hearing Called Party Answer Possible Cause 1: If you are using a speakerphone, there may be environmental factors that affect the performance of the speaker or microphone (for example, too much background noise). What to do: See “Speakerphone Performance Tips” in Chapter 3 for suggestions on the proper use of the speakerphone.
Problems with Combination Extensions Phone Does Not Work Properly Possible Cause 1: Ringer equivalents are too high for the extension. What to do: Be sure the total of the two devices’ Ringer Equivalence Numbers (REN) does not exceed 2.0. If it does, unplug one of the devices.
Problems with Auxiliary Equipment Standard Device Does Not Answer Possible Cause: A standard device (such as a fax machine or answering machine) does not answer intercom calls or transferred calls because it does not recognize the distinctive ringing pattern used by the system.
Zeroes Print in Station or Duration Field on SMDR Printout Possible Cause: If zeroes print in the Station field, a caller is hanging up before someone answers the call. If zeroes print in the Duration field, the user is attempting to answer a call but disconnecting it inadvertently.
Call on Hold Hangs Up, but Line Does Not Disconnect Possible Cause 1: Hold Disconnect Time setting is too long. What to do: Change Hold Disconnect Time (#203) from Long to Short.
Multiple Phones Dead: No Dial Tone or Lights Possible Cause 1: The LED on one system module is out. What to do: If the green LED on the front of a module is out, try reseating the module in the control unit. ■ If the LED lights, the problem is corrected.
Specifications A Capacities System 206 Module Extension Jack ■ 24 outside lines via line jacks on ■ 2 outside lines ■ Maximum 2 devices per extension four 206 plus four 400 modules ■ 6 extensions jack, total REN on jack not to ■ 48 extensions via extension jacks exceed 2.
Switch Fabric ■ Full digital, nonblocking Electrical ■ 10 Watts (35 BTU/hour) per 400 module, normal and maximum power consumption Specifications ■ 65 Watts (225 BTU/hour) per 206 module during normal operation ■ 100 Watts (350 BTU/hour) per 206 module during maximum power consumption ■ U.
Electrical ■ U.S. and Canada: 90–130 VAC, 50–60 Hz, 3-prong outlet separate ground, separately fused at Requirements 15 Amps Other countries: 90–264 VAC, fused at 10 Amps ■ Outlet must not be controlled by an on/off switch ■ Grounding to comply with Underwriters Laboratories (UL) 1459: A.
Maintenance, Repair, and Ordering Information B Maintenance Your system is designed to provide trouble-free performance without any special maintenance procedures.
In-Warranty Repairs If you purchased or leased your system directly from Lucent Technologies, Lucent Technologies will repair it free of charge during the one-year warranty period. Simply call the hotline and ask for service. Business-Day service is standard during the warranty period for both the control unit and system phones.
If you purchased your system directly from Lucent Technologies, Lucent Technologies will perform warranty repair in accordance with the terms and conditions of the specific type of Lucent Technologies maintenance coverage you selected.
Product Ordering Information Reference Materials In addition to this guide, the following materials are available (the order numbers are in parentheses): ■ ■ ■ ■ ■ ■ ■ ■ System Planner (518-455-338) provides the forms needed to plan and record how your system and telephones are to be programmed.
Hardware Components Ordering additional telephones and modules, accessories, and replacement parts for your system is convenient. Table B-1 (on the next two pages) shows where you can buy system components in the United States.
To use Table B-1, first locate the item you want. A triangle ( ▲ ) indicates where you can obtain it. System Modules and Wiring: SOURCE (U.S.) Lucent Lucent Lucent Lucent Technologies Technologies T.
To use Table B-1, first locate the item you want. A triangle ( ▲ ) indicates where you can obtain it. System Telephones and Accessories: SOURCE (U.S.
FCC and IC Information C Federal Communications Commission (FCC) Interference Information This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC rules.
■ Notification to the Telephone Companies: Before connecting this equipment, you or your equipment supplier must notify your local telephone company’s business office of the following: – The telephone number(s) you will be using with this equipment.
IC Notification and Repair Information The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The IC does not guarantee the equipment will operate to the user’s satisfaction.
Renseignements sur la notification du ministére des Industrie Canada et la réparation L’étiquette du ministére des Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications.
Speed Dial Form D Speed Dial Form This appendix contains a Speed Dial Form to be photocopied and handed out to system users. It provides space for System and Personal Speed Dial numbers. For instructions on programming and using System and Personal Speed Dial numbers, see Chapter 5.
PARTNER® II Communications System To Dial ● On a system phone, press [ Feature ] + Code ● On a standard phone, press [ # ] + Code while receiving intercom dial tone.
PARTNER® II Communications System To Dial ● On a system phone, press [ Feature ] + Code ● On a standard phone, press [ # ] + Code while receiving intercom dial tone. Personal Speed Dial Numbers Extension Code Name/Company Telephone Number 80 81 Code 82 83 84 85 86 87 96 89 To program Personal Speed Dial Numbers, see the User Instruction Cards.
Programming Mixed Telephone Types E Overview This appendix provides information about programming from a PARTNER-34D phone to MLS-model phones and from an MLS-34D phone to PARTNER-model phones.
PARTNER-34D Overlay MLS-6 Phone MLS-18D/12D/12 Phone MLS-34D Phone Figure E-1. Programming from a PARTNER-34D Phone E-2 Programming Mixed Telephone Types.
PARTNER-6 Phone MLS-34D Overlay PARTNER-18D/18 Phone PARTNER-34D Phone Figure E-2. Programming from an MLS-34D Phone Programming Mixed Telephone Types E-3.
Glossary B A Account code A code of up to 16 digits that is associated with incoming or outgoing telephone calls. Entry of an account code may be optional or forced. If entered, an account code appears on the call record for a call. See also Call report, Forced Account Code Entry, and Forced Account Code List.
Call Waiting A feature that lets standard phone users receive notification of a second incoming call when they are busy on a call. The user can press the switchhook to put the first call on hold and answer the second call. Caller ID A feature that displays an incoming caller’s number (or name) on a system display phone.
E Expansion carrier The optional component of the control unit that can be connected to the primary carrier to expand your system’s line and extension capacity. See also Primary carrier. Expansion processor module The main module of the expansion carrier, which must be installed in the center slot of the expansion carrier.
Hotline phone A standard phone at an extension which rings another extension automatically when the handset is lifted. See also External Hotline. Hunt Group A group of extensions that takes incoming or transferred calls in round-robin fashion.
M Outside pool See Pool. Mailbox See Voice mailbox. Manual Signaling A feature that lets a user signal an extension by pressing a programmed button. The phone at the target extension beeps for as long as the button is pressed. Alternatively, the Manual Signaling button can be used to ring or voice signal the target extension.
Pooled extension An extension in Hybrid mode that has pool buttons or pool and line buttons. See also Hybrid mode and Key extension. Primary carrier The required component of the control unit that contains the primary processor module and 206 modules and 400 modules.
System mode One of two operating modes, Key or Hybrid, that determines how users access outside lines from their phones. The system mode is determined by a hardware setting in the processor module. See also Hybrid mode and Key mode. System phones The Lucent Technologies telephones that are specifically designed for use with PARTNER systems.
Index A AA Extensions (#607), 5-3 Abbreviated Ringing (#305), 5-4 Accessories, B-5 - B-7 Account Code Entry, 5-5 - 5-7, 5-90, 5-92 Adding lines and extensions, 2-6, 2-7 Allowed List Assignments (#408).
Covering calls, 5-36 - 5-39 Credit card scanners, 4-12 Cycle programming method, 2-18 D Date, System (#101), 5-178 Day, System (#102), 5-179 Dead phones, 6-16 - 6-17 Delayed ring, 5-124 DFT (see Line).
Fax Management button, 4-13, 5-89 FCC information, A-1 Feature button, 3-2 Feature phones, 3-11 Features call handling, 3-13 dial-code, 3-14 overview, 1-1 speed dialing, 2-9, 2-20 user-programmable, 2.
Light patterns description of, 3-4 - 3-5 Fax Management button, 4-13 Intercom Auto Dial button, 2-21, 3-4 - 3-5 Line adapter, B-6 adding to system, 2-6 - 2-7 assigning to extensions, 2-3 - 2-4, 5-118 .
changing type, 2-19, 2-26 P PAGE jack, 1-3, 4-2, A-1 - A-2 Paging, 5-167 Calling Groups, 5-96 Loudspeaker, 5-126 - 5-127, 5-167 - 5-168 PARTNER-model phones, 5-99 - 5-101 Simultaneous, 5-167 - 5-168 P.
Restrictions, dialing disallowed phone numbers, 5-70 - 5-71 for fax machine, 4-15 for long-distance, 5-187 for pooled extensions, 5-152 line access, 5-116 locking an extension, 5-175 - 5-176 overridin.
System phones (continued) speaker, 3-6 using, 3-1, 3-13 wireless, 3-3, B-4, B-7 System Planner, B-4 System problems, 6-15 - 6-17 System programming (see also Programming) changing, 2-6, 2-14 for PBX/C.
Centralized Telephone Programming Quick Reference Place the Programming Overlay on the dialpad of the system display phone at extension 10 or 11 TO ENTER PROGRAMMING MODE TO PROGRAM ANOTHER FEATURE DI.
System Features Continued GROUP HUNTING–RING/VOICE SIGNAL For ringing the first available extension: PRESS a programmable button (p. 5-99) PRESS left [ Intercom ] [ 7 ] [ 7 ] DIAL a Hunt Group numbe.
System Programming Quick Reference Place the Programming Overlay on the dialpad of the system display phone at extension 10 or 11 TO START SYSTEM TO END SYSTEM PROGRAMMING TO CYCLE THROUGH SYSTEM TO C.
SYSTEM RESET – PROGRAMMING SAVED (p. 5-181) IMPORTANT: Using this procedure disconnects any active calls but retains system settings. Use it only if the system fails to function correctly after a power failure or down period. DIAL #728 Extensions POOL EXTENSION ASSIGNMENT DIAL #314 (p.
System Programming Quick Reference Place the Programming Overlay on the dialpad of the system display phone at extension 10 or 11 TO START SYSTEM TO END SYSTEM PROGRAMMING TO CYCLE THROUGH SYSTEM TO C.
Groups Auxiliary Equipment PICKUP GROUP EXTENSIONS DIAL #501 (p. 5-151) DIAL a group number (1–4) DIAL an extension number (10–57) DIAL 1 = Assigned to group 2 = Not Assigned to group ✔ PRESS [ Next Item ] to assign another extension CALLING GROUP EXTENSIONS DIAL #502 (p.
Lucent Technologies 518-455-334 Comcode 107879231 Issue 2 August 1996.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lucent Technologies 4.1 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lucent Technologies 4.1 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lucent Technologies 4.1, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lucent Technologies 4.1 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lucent Technologies 4.1, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lucent Technologies 4.1.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lucent Technologies 4.1. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lucent Technologies 4.1 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
