Manuel d'utilisation / d'entretien du produit MKS (2014) du fabricant Lincoln
Aller à la page of 464
January 2014 Second Printing Owner’s Manual Lincoln MKS Litho in U.S.A. Owner’ s M anual 201 4 MKS Owner’ s M anual 201 4 MKS lincolnowner.com lincolncanada.
Introduction 9 Child Safety 18 Child seat positioning ................................... 2 0 Booster seats ......................................... 2 2 Installing child seats .................................... 2 5 Child safety locks ..............
MyKey 65 Settings, MyKey ....................................... 6 5 Creating ............................................. 6 6 C l e a r i n g ............................................. 6 7 System status ......................................... 6 7 Remote start, MyKey .
Lighting 88 Lighting control ....................................... 8 8 Autolamps ........................................... 8 9 Instrument lighting dimmer ............................... 8 9 Headlamp exit delay .................................... 9 0 Automatic high beam control .
Seats 130 Sitting in the correct position ............................ 1 3 0 Head restraints ....................................... 1 3 1 Power seats ......................................... 1 3 4 Memory function ....................................
T raction Control 182 T r a c t i o nC o n t r o l ™ .................................... 1 8 2 Stability Control 183 AdvanceT rac® ....................................... 1 8 4 Parking Aids 185 Sensing system ......................................
Roadside Emergencies 241 Getting roadside assistance .............................. 2 4 1 Hazard warning flashers ................................ 2 4 2 Fuel cut-off switch .................................... 2 4 2 Jump-starting the vehicle .........
V ehicle Care 289 Cleaning products ..................................... 2 8 9 Cleaning the exterior .................................. 2 8 9 W a x i n g ............................................. 2 9 1 Repairing minor paint damage ...............
Ford Extended Service Plan 335 Audio System 338 MyLincoln T ouch™ system .............................. 3 4 0 MyLincoln T ouch™ 342 Infotainment display ................................... 3 4 9 V oice recognition .................................
ABOUT THIS MANUAL Thank you for choosing Ford. W e recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.
SYMBOL GLOSSAR Y W ARNING: Y ou risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol.
Symbol Description Symbol Description Symbol Description Fuel pump reset Fuse compartment Hazard warning flasher Heated rear window Interior luggage compartment release Jack Lighting control Low tire .
DA T A RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems.
Note: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data or information (e.g., name, gender , age, and crash location) is recorded (see limitations regarding 911 Assist and T raffic, Directions and Information privacy below).
Additionally , when you connect to T raffic, Directions and Information (if equipped, U.S. only), the service uses GPS technology and advanced vehicle sensors to collect the vehicle’ s current locat.
REPLACEMENT P ARTS RECOMMENDA TION Y our vehicle has been built to the highest standards using quality parts. W e recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair .
Special Instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: Please read the Supplementary Restraints System chapter . Failure to follow the specific warnings and instructions could result in personal injury .
EXPORT UNIQUE (NON–UNITED ST A TES/CANADA) VEHICLE SPECIFIC INFORMA TION For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this owner’ s manual.
GENERAL INFORMA TION See the following sections for directions on how to properly use safety restraints for children. W ARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your vehicle.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 ft. 9 in.
CHILD SEA T POSITIONING W ARNING: Airbags can kill or injure a child in a child seat. Never place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat upon which the child seat is installed all the way back.
W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash. W ARNING: T o avoid risk of injury , do not leave children or pets unattended in your vehicle.
BOOSTER SEA TS W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.
T ypes of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’ s head (as measured at the tops of the ears) above the top of the seat.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
INST ALLING CHILD SEA TS Child Seats Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). Using Lap and Shoulder Belts W ARNING: Airbags can kill or injure a child in a child seat.
• Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place the vehicle seat upon which the child seat will be installed in the upright position.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt.
Using Lower Anchors and T ethers for CHildren (LA TCH) W ARNING: Never attach two child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
The LA TCH anchors are located at the rear section of the rear seat between the cushion and seat back below the symbols as shown. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments. Follow the instructions on attaching child safety seats with tether straps.
Using T ether Straps Many forward-facing child safety seats include a tether strap which extends from the back of the child safety seat and hooks to an anchoring point called the top tether anchor . T ether straps are available as an accessory for many older safety seats.
2. Locate the correct anchor for the selected seating position. 3. Open the tether anchor cover . 4. Clip the tether strap to the anchor as shown. 5. T ighten the child safety seat tether strap according to the manufacturer’ s instructions.
CHILD SAFETY LOCKS The childproof locks are located on the rear edge of each rear door and must be set separately for each door . When these locks are set, the rear doors cannot be opened from the inside. • Insert the key and turn to the lock position (key horizontal) to engage the childproof locks.
PRINCIPLES OF OPERA TION W ARNING: Never let a passenger hold a child on his or her lap while your vehicle is moving. The passenger cannot protect the child from injury in a crash. W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. W ARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child.
F ASTENING THE SAFETY BEL TS The front outboard and rear safety restraints in your vehicle are combination lap and shoulder belts. 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch.
Using Safety Belts During Pregnancy W ARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest.
V ehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
.
Conditions of Operation If... Then... The driver safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
If... Then... The driver and front passenger safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder feature will not activate.
Read Step s1-5t horoughly before proceeding with the programming procedure. Note: If you are using MyKey , you cannot disable Belt-Minder . Also, if the Belt-Minder has been previously disabled, it will be re-enabled during the use of MyKey . See the MyKey chapter .
CHILD RESTRAINT AND SAFETY BEL T MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts.
PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
PRINCIPLES OF OPERA TION W ARNING: Airbags do not inflate slowly or gently , and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module.
W ARNING: If the airbag has deployed, the airbag will not function again and must be replaced immediately . If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.
DRIVER AND P ASSENGER AIRBAGS W ARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury .
Proper Driver and Front Passenger Seating Adjustment W ARNING: The National Highway T raffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’ s chest and the driver airbag module. Failure to follow this could seriously increase the risk of injury or death.
FRONT P ASSENGER SENSING SYSTEM W ARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position.
The front passenger sensing system uses a passenger airbag status indicator which will illuminate indicating that the front passenger frontal airbag is either ON (enabled) or OFF (disabled). The indicator lamp is located in the center stack of the instrument panel.
• Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator OFF lamp remains lit even after this, the person should be advised to ride in the rear seat.
The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the previous list.
SIDE AIRBAGS W ARNING: Do not place objects or mount equipment on or near the airbag cover , on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.
The system consists of the following: • A tag on the seatback indicating that side airbags are found on your vehicle. • Side airbags located inside the seatback of the driver and front passenger seats. • Crash sensors and monitoring system with readiness indicator .
W ARNING: All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.
Children 12 years old and under should always be properly restrained in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening.
If any of these things happen, even intermittently , have the supplemental restraint system serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a crash.
GENERAL INFORMA TION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditio.
REMOTE CONTROL Intelligent Access Key Y our intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to activate the push-button start system. The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door .
Intelligent Access Transmitter 1. Remove the backup key from the transmitter . 2. T wist a thin coin under the tab hidden behind the backup key head to remove the battery cover . Do not use the backup key to remove the cover or you could damage the intelligent access key .
Programming Memory to the Transmitter 1. Move the memory features to the desired positions using the associated controls. 2. Press and hold button 1 until a tone is heard to confirm setting. Continue to hold until a second tone is heard. 3. W ithin three seconds press lock button on the remote control.
Remote Start W ARNING: T o avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well ventilated. Note: Do not use remote start if your vehicle is low on fuel. The remote start button is on the transmitter .
Remote Starting the V ehicle Note: Y ou must press each button within three seconds of each other . Y our vehicle will not remote start and the horn will not sound if you do not follow this sequence. The label on your transmitter details the starting procedure.
Turning the V ehicle Off After Remote Starting Press the button once. The parking lamps will turn off. Y ou may have to be closer to your vehicle than when starting due to ground reflection and the added noise of the running vehicle. Y ou can disable or enable the remote start system through the information display .
PRINCIPLES OF OPERA TION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys.
• Audio system maximum volume of 45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled.
Note: Y ou can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey . Once you have switched the engine off, however , you will need an admin key to change or clear your MyKey settings. CLEARING ALL MYKEYS Y ou can clear all MyKeys within the same key cycle as you created the MyKey .
MYKEY TROUBLESHOOTING Condition Potential causes I cannot create a MyKey . • The key or fob used to start the vehicle does not have admin privileges. • The key or fob used to start the vehicle is the only admin key (there always has to be at least one admin key).
LOCKING AND UNLOCKING Y ou can use the power door lock control or the remote control to lock and unlock your vehicle. Power Door Locks The power door lock control is located on the driver and front passenger door panels. A. Unlock B. Lock Remote Control Y ou can use the remote control anytime your vehicle is not running.
Note: If any door or the luggage compartment is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn sounds twice and the lamps will not flash. Opening the Trunk Press the button twice within three seconds to open the trunk.
Smart Unlocks The smart unlock feature is intended to prevent you from unintentionally locking your intelligent access key inside your vehicle’ s passenger compartment or rear cargo area.
Autounlock Feature (If Enabled) The autounlock feature unlocks all the doors when: • the ignition is on, all the doors are closed, and your vehicle has been in motion at a speed greater than 12 mph .
Illuminated Exit The interior lamps and select exterior lamps illuminate when all doors are closed and the ignition is turned off. The lights turn off if all the doors remain closed and: • 25 seconds elapse • you press the ST AR T/STOP button.
Programming a Personal Entry Code T o create your own personal entry code: 1. Enter the factory-set code. 2. Press the 1 • 2 on the keypad within five seconds. 3. Enter your personal 5-digit code. Y ou must enter each number within five seconds of each other .
Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash.
From Outside Y our V ehicle 1. Unlock the trunk with the remote control or power door lock control. The trunk unlocks when you press the release button if the intelligent access transmitter is within 3 feet (1 meter) of the trunk. 2. Press the release button located near the license plate.
Adults should familiarize themselves with the operation and location of the release handle. The handle is located inside the luggage compartment either on the luggage compartment door (lid) or near the tail lamps. It is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
SECURILOCK® P ASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Programming a Spare Intelligent Access Key Note: A maximum of four intelligent access keys can be programmed to your vehicle. Y ou must take your vehicle and all access keys to your authorized dealer .
ANTI-THEFT ALARM The system will warn you of unauthorized entry to your vehicle. The turn signal lamps will flash and sound the horn up to a total of 10 times when: • any door , the hood or the lugg.
ADJUSTING THE STEERING WHEEL W ARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting in the Correct Position in the Seats chapter . Use the control on the side of the steering column to adjust the position.
T o reset the steering column to its normal stopping position: 1. Press the steering column control again after encountering the new stopping position. 2. Continue pressing the control until it reaches the end of the column position. A new stopping position will be set.
CRUISE CONTROL T ype 1 T ype 2 See the Cruise Control chapter for information on this feature. INFORMA TION DISPLA Y CONTROL See the Information Displays chapter for more information.
Cluster Display Control Features Use this control to adjust the right side of the cluster display . Navigate through the screen and press OK to select. See the MyLincoln T ouch chapter . HEA TED STEERING WHEEL (IF EQUIPPED) See the MyLincoln T ouch chapter .
ADJUST ABLE PEDALS (IF EQUIPPED) W ARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press and hold the appropriate control to move the pedals.
WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears.
WINDSHIELD W ASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washer before wiping a dry windshield. Note: Do not operate the washer when the washer reservoir is empty .
LIGHTING CONTROL A. Off B. Parking lamps, instrument panel lamps, license plate lamps and tail lamps C. Headlamps High Beams • Push the lever toward the instrument panel to activate. • Push the lever toward the instrument panel again or pull the lever towards you to deactivate.
AUTOLAMPS W ARNING: In severe weather conditions, it may be necessary to switch your headlamps on manually . Note: If the vehicle is equipped with autolamps, it will have the windshield wiper rainlamp feature.
HEADLAMP EXIT DELA Y Y ou can set the delay time to keep the headlamps on for up to three minutes after the ignition is turned off. Follow the steps below to change the delay time (Steps 1 through 6 must be done within 10 seconds): 1. T urn the ignition off.
AUTOMA TIC HIGH BEAM CONTROL (IF EQUIPPED) The system will automatically turn on your high beams if it is dark enough and no other traffic is present. When it detects an approaching vehicle’ s headl.
The high beams will switch off if: • An approaching vehicle’ s headlights or a preceding vehicle’ s tail lamps are detected. • The vehicle speed falls below 19 mph (30 km/h). • The ambient light level is high enough that high beams are not needed.
FRONT FOG LAMPS The fog lamps can be turned on when the lighting control is pulled toward you and in the headlamps, parking lamps or autolamps positions.
Note: There is a delay of two to five seconds before the adaptive headlamp system will operate when the vehicle is driven. Note: The system is only active at speeds above 3 mph (5 km/h).
.
POWER WINDOWS W ARNING: Do not leave children unattended in your vehicle and do not let children play with the power windows. They may seriously injure themselves. W ARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings.
Opening the Windows Press and hold the unlock button on the remote control to begin opening the windows and venting the moonroof (if equipped). The power sunscreen will also open.
Window Lock Press the control to lock or unlock the rear window controls. Accessory Delay Y ou can use the window switches for several minutes after you switch the ignition off, or until you open either front door . EXTERIOR MIRRORS Power Exterior Mirrors W ARNING: Do not adjust the mirror while your vehicle is in motion.
Foldaway Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Heated Exterior Mirror The heated exterior mirrors switch on with the heated rear window .
The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B).
Auto-Dimming Mirror Note: Do not block the sensors on the front and back of the mirror . Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor . The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle.
SUNSHADE (IF EQUIPPED) The power rear sunshade covers the rear window of the vehicle. The control is located in the center console access bin. Press the control to move the sunshade up or down. Note: Do not try to manually move the sunshade. The sunshade has a one-touch down feature.
Opening and Closing the Sunscreen Press and release the control to open the sunscreen. Note: The sunscreen stops at the first panel for the dual panel moon roof. Press again and release to continue to open the sunscreen past the second panel. Pull and release the control to close the sunscreen.
GAUGES Cluster shown in standard measure – metric clusters similar . A. Left information display . See Information displays for more information. B. Speedometer C.
Adaptive cruise control (if equipped) (RTT) The speed control system indicator light changes color to indicate what mode the system is in: • On (white light): Illuminates when the adaptive cruise control system is turned on. T urns off when the speed control system is turned off.
W ARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur . It will take you longer to stop the vehicle. Have the vehicle checked by your authorized dealer as soon as possible.
Grade assist (if equipped) (RTT) Illuminates when grade assist is turned on. Heads up display (if equipped) A red beam of lights will illuminate on the windshield in certain instances when using adaptive cruise control and/or the collision warning system.
Safety belt Reminds you to fasten your safety belt. A Belt-Minder® chime will also sound to remind you to fasten your safety belt. Service engine soon The service engine soon indicator light illumina.
Stability Control System Displays when the AdvanceT rac®/T raction control is active. If the light remains on, have the system serviced immediately . Stability Control System Off Illuminates when AdvanceT rac®/T raction control has been disabled by the driver .
GENERAL INFORMA TION W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
Display Mode Use the up/down arrow buttons to choose between the following display options. Display mode Display mode Option 1 Option 2 Option 3 XXX mi (km) to empty X Bar tachometer X Round tachomete.
T r i p1&2 Choose between the standard or enhanced trip display . T r i p1&2 T r i p1&2 T rip distance A verage fuel economy Elapsed trip time Hold OK to Reset Estimated amount of fuel consumed T otal odometer (lower left corner) Press and hold OK to reset the currently displayed trip information.
Driver Assist In this mode, you can configure different driver setting choices. Note: Some items are optional and may not appear . Driver Assist T raction Ctrl — check enabled (default) / uncheck di.
Settings V ehicle Drive Control Handling in D Sport / Normal / Comfort Handling in S Sport / Normal Auto Engine Off — check enabled / uncheck disabled DTE Calculation Normal / T owing Easy Entry/Exi.
Settings (cont’d) *MyKey Mykey Status MyKeys / Admin Keys Create MyKey Hold OK to Create MyKey 911 Assist Always On / User Selectable T raction Control Always On / User Selectable Max Speed Choose d.
INFORMA TION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have. Press the OK button to acknowledge and remove some messages from the information display .
Alarm/Security Messages Action / Description V ehicle Alarm T o Stop Alarm, Start V ehicle. Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on the driver’ s side door .
A WD Messages Action / Description Change A WD Power T ransfer Unit Lube Displayed when the A WD system needs its power transfer unit lubrication changed. This message may be set if a vehicle has experienced extended periods of extreme/severe duty cycle driving.
BLIS® Messages Action / Description Blindspot Not A vailable Sensor Blocked See Manual Displayed when the blind spot information system/cross traffic alert system sensors are blocked. Driver can typically clean the sensor to resolve. Blindspot System Fault Displayed when a fault with the blind spot information system has occurred.
Collision W arning System Messages Action / Description Collision W arning Not A vailable Displayed when there is a system malfunction with the collision warning system.
Keys and Intelligent Access Messages Action / Description No Key Detected Displayed if the intelligent access key is not detected by the system in the following three scenarios: • When the start/stop button is pressed in an attempt to either start the engine or cycle through the ignition states.
Lane Keeping System Messages Action / Description Lane keeping Sys. Malfunction Service required The system has malfunctioned. Contact your authorized dealer as soon as possible. Front Camera T emporarily Not A vailable The system has detected a condition that has caused the system to be temporarily unavailable.
Maintenance Messages Action / Description Service Power Steering Now The power steering system has detected a condition within the power steering system that requires service immediately . See your authorized dealer . Power Steering Assist Fault The power steering system has disabled power steering assist due to a system error .
Passenger Sensing System Message Action / Description Occupant Sensor BLOCKED Remove Objects Near Passenger Seat Displayed when objects are by the passenger seat. After the objects are moved away from the seat, if the warning stays on or continues to come on contact your authorized dealer as soon as possible.
DUAL AUTOMA TIC TEMPERA TURE CONTROL SYSTEM Note: Y ou can switch temperature units between Fahrenheit and Celsius. See Settings in the MyLincoln T ouch chapter . A. MyT emp: Allows you to quickly adjust to a frequently used setting with a single touch.
F. A/C: Press to turn air conditioning off and on. Air conditioning cools the vehicle using outside air . T o improve air conditioning when starting your vehicle, drive with the windows slightly open for two to three minutes. Use air conditioning with recirculated air to improve cooling performance and efficiency .
During extreme high ambient temperatures when idling stationary for extended periods of time in gear , it is recommended to run the air conditioning in the MAX A/C mode, adjust the blower fan speed to the lowest setting and put the vehicle’ s transmission into position P to continue to receive cool air from your air conditioning system.
CABIN AIR FIL TER Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system.
Automatic Climate Systems Automatic Settings Y ou can set the climate control to operate in AUTO mode through the information display setting: Remote Start > Climate Control > Heater – A/C > Auto. The climate control system automatically sets the interior temperature to 72°F (22°C).
SITTING IN THE CORRECT POSITION W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash.
• Keep sufficient distance between yourself and the steering wheel. W e recommend a minimum of 10 inches (25 centimeters) between your breastbone and the airbag cover . • Hold the steering wheel with your arms slightly bent. • Bend your legs slightly so that you can press the pedals fully .
Front seat head restraints The head restraints consist of: A. An energy absorbing head restraint B. T wo steel stems C. Guide sleeve adjust and release button D.
Rear seat non-adjustable outboard head restraints The head restraints consist of: A. An energy absorbing head restraint B. T wo steel stems C. Guide sleeve unlock and remove button • Remove: Simultaneously press and hold both unlock and remove buttons (C), then pull up on the head restraint.
POWER SEA TS W ARNING: Never adjust the driver’ s seat or seatback when your vehicle is moving. W ARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seat back.
T o reset the seat to its normal stopping position: 1. After encountering the new stopping position, press the power seat control again to override. 2. Continue pressing the control until it reaches the end of the seat track. 3. Continue pressing the control for about two seconds.
• Lumbar adjust: Press and hold the front of the lumbar control (B) to increase the firmness of the selected portion of the seat back or press and hold the rear of the lumbar to decrease the firmness. • Power seat controls (C) W e recommend first selecting the lumbar to the desired setting and then selecting the back or cushion massage setting.
Recalling a memory position with the remote control The memory positions are also recalled when you press unlock on your remote control (if the transmitter is programmed to a memory position) or , when you enter a valid personal entry code that is programmed to a memory position.
Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly .
T o remove an air filter: 1. T urn the vehicle off. 2. Push up on the outside rigid edge of the filter and rotate counterclockwise once the tabs are released, then remove the filter . T o install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing.
Armrest pass-through Pull down the door located in back of the armrest in order to store cargo of a longer length such as skis or lumber . Note : Do not exceed 80 pounds (36 kilograms) of weight on the pass-through door .
Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly . The rear seat heat controls are located on the rear of the center console.
HOMELINK® WIRELESS CONTROL SYSTEM (IF EQUIPPED) W ARNING: Make sure that the garage door and security device are free from obstruction when you are programming.
Programming Note: Put a new battery in the hand-held transmitter . This will ensure quicker training and accurate transmission of the radio-frequency signal. 1. W ith your vehicle parked outside of the garage and your key in the ignition, turn the key so that the ignition is in the on position.
After programming the HomeLink button, follow Step s5–7a sl i s t e d below to program your garage door opener . Note: Y ou may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener .
Programming HomeLink to a Genie Intellicode 2 garage door opener Note: The Genie Intellicode 2 transmitter must already be programmed to operate with the garage door opener . Programing the transmitters T o program HomeLink to the transmitter you must first put the transmitter into programming mode.
Programming HomeLink to the Genie Intellicode garage door opener motor Note: Y ou may need a ladder to access the garage door opener motor . T o program HomeLink to the garage door opener motor: 1. Press and hold the PROGRAM button on the garage door opener motor until both blue LED’ s turn on.
AUXILIAR Y POWER POINTS W ARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty , and can result in fire or serious injury . Note: If used when the engine is not running, the battery will discharge.
CENTER CONSOLE Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. A vailable console features include: A. Cupholders B. Sliding driver and passenger arm rests, utility compartment with audio input jack, USB port and power point C.
GENERAL INFORMA TION W ARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. W ARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover .
KEYLESS ST ARTING W ARNING: The keyless starting system may not function if the key is close to metal objects or electronic devices such as mobile phones. Note: A valid passive key must be located inside the vehicle to switch the ignition on and start the engine.
ST ARTING A GASOLINE ENGINE When you start the engine, the idle speed increases, this helps to warm up the engine. If the engine idle speed does not slow down automatically , have your vehicle checked by an authorized dealer .
Fast Restart The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. W ithin 20 seconds of switching the engine off, press the brake pedal and press the button. After 20 seconds have expired, you can no longer start the engine without the key present inside your vehicle.
• During the countdown before engine shutdown, you are prompted to press OK or RESET (depending on your type of information display) to temporarily switch the feature off (for the current ignition cycle only). Stopping the Engine When Y our V ehicle is Stationary 1.
Important V entilating Information If you stop your vehicle and leave the engine idling for long periods, we recommend that you do one of the following: • Open the windows at least 1 inch (2.5 centimeters). • Set your climate control to outside air .
• Make sure your vehicle is parked in a clean area, clear of combustibles. • Make sure the heater , heater cord and extension cord are firmly connected. • Check for heat anywhere in the electrical hookup once the system has been operating for approximately 30 minutes.
SAFETY PRECAUTIONS W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. W ARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
Choosing the Right Fuel With a Flex Fuel V ehicle (If Equipped) Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 85% ethanol (E-85) in your Flex Fuel V ehicle (FFV). If your vehicle is flex fuel capable, it will have a yellow bezel placed over the fuel fill inlet.
RUNNING OUT OF FUEL A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine.
When filling the vehicle’ s fuel tank from a portable fuel container , use the funnel included with the vehicle. 1. Locate the white plastic funnel in the spare tire compartment. 2. T o open the fuel filler door , press the center of the rear edge and then release.
Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling.
3. Slowly insert the fuel filler nozzle fully into the fuel system, and leave the nozzle fully inserted to open both doors until you are done pumping. Hold handle higher during insertion for easier access.
If this action corrects the problem, the message may not reset immediately . It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after four or more hours with the engine off) followed by city or highway driving.
5. Calculate fuel economy as follows: Standard: Divide miles traveled by gallons used. Metric: Multiply liters used by 100, then divide by kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway). This provides an accurate estimate of the vehicle’ s fuel economy under current driving conditions.
Illumination of the service engine soon indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly . An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle.
If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity . Although some malfunctions detected by the OBD-II may not have symptoms that are appare.
AUTOMA TIC TRANSMISSION W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the off position and remove the key whenever you leave your vehicle. Y our vehicle has been designed to improve fuel economy by reducing fuel usage while coasting or decelerating.
S (Sport) Moving the gearshift lever to S (Sport): • Provides additional grade (engine) braking and extends lower gear operation to enhance performance for uphill climbs, hilly terrain or mountainous areas. This will increase engine RPM during engine braking.
When using the paddles for manual shifting: • Pull the right paddle (+) to upshift. • Pull the left paddl e(–)t o downshift. Upshift to the recommended shift speeds according to the following ch.
Brake-shift interlock W ARNING: Do not drive your vehicle until you verify that the brakelamps are working. W ARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely . T o avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure.
If the fuse is not blown and the brake lamps are working properly , the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake, turn the ignition off, and remove the key . 2. Using a screwdriver (or similar tool), remove the locking tab to the driver side panel and remove.
Automatic T ransmission Adaptive Learning This feature is designed to increase durability and provide consistent shift feel over the life of the vehicle. A new vehicle or transmission may have firm shifts, soft shifts or both. This operation is considered normal and will not affect function or durability of the transmission.
USING YOUR ALL-WHEEL DRIVE (A WD) SYSTEM (IF EQUIPPED) A WD uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicles cannot. The A WD system is active all the time and requires no input from the operator .
Driving In Special Conditions With All-Wheel Drive (A WD) A WD vehicles are equipped for driving on sand, snow , mud and rough roads and have operating characteristics that are somewhat different from conventional vehicles, both on and off the highway .
If Y our V ehicle Gets Stuck W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the lock position and remove the key whenever you leave your vehicle.
Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. A void reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid excessive wheel slip.
After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components. Note: Driving through deep water may damage the transmission.
Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control.
Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, apply the brake steadily . Since your vehicle is equipped with a four wheel anti-lock brake system (ABS), do not “pump” the brakes.
GENERAL INFORMA TION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn out.
Anti-Lock Brake System This system helps you maintain steering control during emergency stops by keeping the brakes from locking. This lamp momentarily illuminates when you turn the ignition on. If the light does not illuminate during start-up, remains on or flashes, the anti-lock brake system may be disabled and may need to be serviced.
PRINCIPLES OF OPERA TION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time.
PRINCIPLES OF OPERA TION W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel or tire size may change the handling characteristics of your vehicle and may adversely affect the performance of the AdvanceT rac® system.
A V ehicle without AdvanceT rac® skidding off its intended route. B V ehicle with AdvanceT rac® maintaining control on a slippery surface. USING ADV ANCETRAC® The system automatically activates when you start your engine.
SENSING SYSTEM W ARNING: T o help avoid personal injury , please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds.
The system can be turned off using the information display control. Refer to the Information Display chapter . If a fault is present in the system, a warning message appears in the information display and does not allow the driver to switch the faulted system on.
Front Sensing System The front sensors are active when the gearshift is in any position other than P (Park) or N (Neutral) and the vehicle speed is below 7 mph (12 km/h). A. Coverage area of up to 27 inches (70 centimeters) from the front of the vehicle and about 6–14 inches (15–35 centimeters) to the side of the front end of the vehicle.
ACTIVE P ARK ASSIST (IF EQUIPPED) W ARNING: This system is designed to be a supplementary park aid. It may not work in all conditions and is not intended to replace the driver’ s attention and judgment. The driver is responsible for avoiding hazards and maintaining a safe distance and speed, even when the system is in use.
Using Active Park Assist Press the button; the touch screen displays a message and a corresponding graphic to indicate it’ s searching for a parking space.
Automatic Steering into Parking Space Note: If vehicle speed exceeds 6 mph (10 km/h), the system turns off and you need to take full control of the vehicle. Note: If a maneuver is interrupted before completion, the system turns off and you need to full take control of the vehicle.
Deactivating the Park Assist Feature The system can be deactivated manually by: • pressing the active park assist button • grabbing the steering wheel • driving above approximately 20 mph (35 km.
The system does not position the vehicle where I want in the space The vehicle is rolling in the opposite direction of the transmission (i.e. rolling forward when R [Reverse] is selected) The transmis.
W ARNING: Use caution when using the rear video camera and the trunk is ajar . If the trunk is ajar , the camera will be out of position and the video image may be incorrect. All guidelines will be removed when the trunk is ajar . W ARNING: Use caution when turning camera features on or off while in R (Reverse).
Note: The camera may not operate correctly under the following conditions: • Nighttime or dark areas if one or both reverse lamps are not operating. • The camera’ s view is obstructed by mud, water or debris. Clean the lens with a soft, lint-free cloth and non-abrasive cleaner .
are getting closer to your vehicle as they move from the green zone to the yellow or red zones. Use the side view mirrors and rear view mirror to get better coverage on both sides and rear of the vehicle. Enhanced Park Aids Note: Enhanced park aids is only available when the transmission is in R (Reverse).
PRINCIPLES OF OPERA TION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. USING CRUISE CONTROL W ARNING: Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery .
Changing the Set Speed Note: If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, you will return to the speed that you previously set. • Press SET up or down and hold to increase or decrease the set speed.
W ARNING: Do not use in poor visibility , specifically fog, rain, spray or snow . Note: It is your responsibility to stay alert, drive safely and be in control of your vehicle at all times. The system adjusts your speed to maintain a proper distance between you and the vehicle in front of you in the same lane.
The information display will show a green indicator light, current gap setting and desired set speed. 4. T ake your foot off the accelerator pedal. 5. A lead vehicle graphic will illuminate if there is a vehicle detected in front of you.
The vehicle brakes will be automatically applied to slow your vehicle to maintain a safe distance from the vehicle in front. The maximum braking which is applied by the system is limited and can be overridden by the driver applying the brakes.
Overriding Adaptive Cruise Control W ARNING: Whenever the driver is overriding the ACC by pressing the accelerator pedal, the ACC will not automatically apply the brakes to maintain separation from any vehicle ahead. Y ou can override the set speed and gap distance by pressing the accelerator pedal.
Low Speed Automatic Cancellation The system is not functional at vehicle speeds below 16 mph (26 km/h). An audible alarm sounds and the automatic braking released if your vehicle drops below this speed. Hilly Condition Usage Note: An audible alarm sounds and the system shuts down if it is applying brakes for an extended period of time.
Detection issues can occur: A. When driving on a different line than the vehicle in front. B. W ith vehicles that edge into your lane. The system can only detect these vehicles once they move fully into your lane. C. There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road.
Blocked Sensor W ARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled. Failing to do so may result in loss of vehicle control, which could result in serious injury .
Cause Action Y ou are in a desert or remote area with no other vehicles and no roadside objects. W ait a short time or switch to normal cruise control. Due to the nature of radar technology , it is possible to get a blockage warning and not be blocked.
DRIVER ALERT (IF EQUIPPED) W ARNING: The driver alert system is designed to aid you. It is not intended to replace your attention and judgment. Y ou are still responsible to drive with due care and attention. Note: The system will store the on/off setting in the information display menu through ignition cycles.
System Display When active the system will run automatically in the background and only issue a warning if required. Y ou can view the status at any time using the information display . Refer to the Information Displays chapter . The alertness level is shown by six steps in a colored bar .
LANE KEEPING SYSTEM (IF EQUIPPED) W ARNING: The system is designed to aid the driver . It is not intended to replace the driver’ s attention and judgment.
System Settings The system has one standard feature setting and one optional setting menu available. T o view or adjust the settings, refer to the Information Displays chapter . The last-known selection for each of these settings is stored by the system.
System Display When you switch the system on, an overhead graphic of a vehicle with lane markings will be displayed in the left instrument cluster display . If the aid mode is selected after you switch the system on, arrows will be displayed with the lane markings.
T roubleshooting Why is the feature not available (line markings are gray) when I can see the lane markings on the road? V ehicle speed is outside the operational range of the feature Sun is shining d.
BLIND SPOT INFORMA TION SYSTEM (BLIS®) WITH CROSS TRAFFIC ALERT (CT A) (IF EQUIPPED) W ARNING: T o help avoid injuries, NEVER use the BLIS® as a replacement for using the interior and exterior mirrors and looking over your shoulder before changing lanes.
Using the Systems BLIS® turns on when the engine is started and the vehicle is driven forward above 3 mph (5 km/h); it remains on while the transmission is in D (Drive) or N (Neutral). If shifted out of D (Drive) or N (Neutral), the system enters CT A mode.
Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited. System Lights and Messages The BLIS® and CT A systems illuminate a yellow alert indicator in the outside mirror on the side of the vehicle the approaching vehicle is coming from.
System Sensors W ARNING: Just prior to the system recognizing a blocked condition and alerting the driver , the number of missed objects will increase. T o help avoid injuries, NEVER use the BLIS® as a replacement for using the side and rear view mirrors and looking over your shoulder before changing lanes.
Reasons for messages being displayed Heavy rainfall/snowfall interferes with the radar signals No action required. The system automatically resets to an unblocked state once the rainfall/snowfall rate decreases or stops. Do not use BLIS® and/or CT A in these conditions.
Switching the Systems Off and On One or both systems can be switched off temporarily by using the information display control; refer to the Information Display chapter . When the BLIS® is switched off, the driver does not receive alerts and the information display shows BLIND SPOT SYS OFF and/or CT A SYSTEM OFF .
If it is, a red warning light illuminates and an audible warning chime sounds. The brake support system assists the driver in reducing the collision speed by charging the brakes. If the risk of collision further increases after the warning light illuminates, the brake support prepares the brake system for rapid braking.
Blocked Sensors If a message regarding a blocked sensor appears in the information display , the radar signals from the sensor have been obstructed. The sensors are located behind a fascia cover near the driver side of the lower grille.
System Limitations W ARNING: The collision warning system’ s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’ s brakes. The brake pedal must be pressed just like any typical braking situation.
LINCOLN DRIVE CONTROL Lincoln Drive Control delivers the Lincoln driving experience through a suite of sophisticated electronic vehicle systems. These systems continuously monitor both your driving inputs and the road conditions to optimize ride comfort, steering, handling, powertrain response and sound.
Using Lincoln Drive Control Y ou can configure which of the Drive Control modes are active when the vehicle is in D (Drive) or in S (Sport). The configuration is retained until modified using the information display . T o change the vehicle’ s Drive Control settings, access the main menu on the information display: 1.
W ARNING: Obtain immediate service if a system error is detected. Y ou may not notice any difference in the feel of your steering, but a serious condition may exist. Failure to do so may result in loss of steering control. Y our vehicle is equipped with an electric power -assisted steering system.
LOAD LIMIT V ehicle Loading – With and Without a T railer This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance.
W ARNING: The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available.
Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
• Suppose your vehicle has a 1400 lb. (635 kg) cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb.
TOWING A TRAILER W ARNING: Do not exceed the GVWR or the GA WR specified on the certification label. W ARNING: T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of.
RECOMMENDED TOWING WEIGHTS Note: Do not exceed the trailer weight for your vehicle configuration listed in the chart below . Note: Make sure to take into consideration trailer frontal area. Do not exceed 12 feet 2 (1.11 meters 2 ) trailer frontal area.
Hitches Do not use a hitch that either clamps onto the bumper or attaches to the axle. Distribute the trailer load so 10-15% of the total trailer weight is on the tongue. Safety Chains Note: Never attach safety chains to the bumper . Always connect the safety chains to the hook retainers of your vehicle hitch.
When T owing a T railer • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 kilometers). • Do not make full-throttle starts. • Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 miles (80 kilometers).
Replace the rear axle lubricant anytime the rear axle submerges in water . W ater may have contaminated the rear axle lubricant, which does not normally require checking or changing unless it is leaking or other axle repair is required.
Front-wheel drive vehicles must have the front wheels placed on a tow dolly when towing your vehicle from the rear using wheel lift equipment. This prevents damage to the transmission. T owing an all-wheel drive vehicle requires that all wheels be off the ground, such as using a wheel lift and dollies or flatbed equipment.
Y ou can tow your all-wheel drive vehicle with all four wheels on the ground or with all four wheels off the ground using a vehicle transport trailer . Do not tow your all-wheel drive vehicle with the front wheels off the ground (by using a tow dolly) and the rear wheels on the ground.
BREAKING-IN Y ou need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unique driving characteristics. A void driving too fast during the first 1000 miles (1600 kilometers). V ary your speed frequently and change up through the gears early .
• Drive a heavily loaded vehicle or tow a trailer . • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors, rollbars or light bars, running boards, ski racks).
FLOOR MA TS W ARNING: Always use floor mats that are designed to fit the foot well of your vehicle, leaving the pedal area unobstructed, and which can be firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.
ROADSIDE ASSIST ANCE V ehicles Sold in the United States: Getting Roadside Assistance T o fully assist, if you have a vehicle concern, Ford Motor Company offers a complimentary Roadside Assistance program. This program is separate from the New V ehicle Limited W arranty .
V ehicles sold in the United States: Using roadside assistance United States Lincoln vehicle clients who require Roadside Assistance, call 1–800–521-4140. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest Lincoln dealership within 100 miles (161 kilometers).
In the event of a moderate to severe collision, this vehicle includes a fuel pump shutoff feature that stops the flow of fuel to the engine. Not every impact will cause a shutoff. Should your vehicle shut off after a collision, you may restart your vehicle.
When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may exhibit a combination of firm and soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address Lincoln Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6K 1C8 T elephone 1-800-387-9333 Online www .lincolncanada.com Additional assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1.
IN CALIFORNIA (U.S. ONL Y) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’ s applicable .
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONL Y) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-s.
UTILIZING THE MEDIA TION or ARBITRA TION PROGRAM (CANADA ONL Y) This pertains to vehicles delivered to authorized Canadian dealers. In those cases, where you continue to feel that the efforts by Ford .
If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. V irgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer .
If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P .
Obtaining a French Owner ’ s Manual A French owner’ s manual can be obtained from your authorized dealer or by contacting Helm, Incorporated using the contact information listed previously in this section.
CHANGING A FUSE Fuses W ARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in your vehicle are not working, a fuse may have blown.
FUSE SPECIFICA TION CHART Power Distribution Box W ARNING: Always disconnect the battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs.
Fuse or relay number Fuse amp rating Protected components 4 30A** W iper motor relay 5 50A** Anti-lock brake system pump 6 — Not used 7 — Not used 8 20A** Moonroof, Power sunshade 9 20A** Second r.
Fuse or relay number Fuse amp rating Protected components 34 — Blower motor relay 35 — Left-hand cooling fan #1 relay 36 — Not used 37 — Not used 38 — Not used 39 — Not used 40 30A** Left .
Fuse or relay number Fuse amp rating Protected components 64 — Not used 65 30A* Fuel pump relay , Fuel injectors 66 — Powertrain control module relay 67 20A* Oxygen sensor heater , Mass airflow se.
Fuse or relay number Fuse amp rating Protected components 82 — Not used 83 — Not used 84 — Not used 85 — Not used 86 7.5A* Powertrain control module keep-alive power and relay , Canister vent .
Passenger Compartment Fuse Panel The fuse panel is located under the instrument panel to the left of the steering wheel. Y ou may need to remove a trim panel to access it.
Fuse or relay number Fuse amp rating Protected components 8 10A Not used (spare) 9 10A SYNC module, Electronic finish panel, Radio frequency transceiver module 10 10A Run accessory relay , Wiper relay.
Fuse or relay number Fuse amp rating Protected components 29 20A Radio, Global positioning system module 30 15A Front park lamps 31 5A Not used (spare) 32 15A Smart window motors, Master window and mi.
GENERAL INFORMA TION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers who are there to help you with their professional servicing expertise.
OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hood release handle located at the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the auxiliary latch using the handle that is located under the front passenger side of the hood.
UNDER HOOD OVERVIEW 3.7L V6 engine A. Engine coolant reservoir B. W indshield washer fluid reservoir C. Brake fluid reservoir D. Battery E. Power distribution box F . Air filter assembly G. Automatic transmission fluid dipstick H. Engine oil dipstick I.
3.5L V6 EcoBoost® engine A. Engine coolant reservoir B. Brake fluid reservoir C. Battery D. Power distribution box E. Air filter assembly F . Automatic transmission fluid dipstick (out of view) G.
Engine shield Some vehicles may be equipped with an aero-shield under the engine. This shield needs to be removed for service, including oil and filter changes. It is secured with four quick release fasteners. ENGINE OIL DIPSTICK 2.0L EcoBoost A. MIN B.
Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by the American Petroleum Institute (API).
Adding Engine Coolant W ARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. W ARNING: Do not put engine coolant in the windshield washer fluid container .
• Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant.
Engine fluid temperature management (EcoBoost engine only) W ARNING: T o reduce the risk of collision and injury , be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperatures reduce.
W ARNING: Never remove the coolant reservoir cap while the engine is running or hot. 4. If the coolant level is normal, you may restart your engine and continue on. 5. If the coolant is low , add coolant, restart the engine and take your vehicle to an authorized dealer .
When Fail-Safe Mode is Activated Y ou have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1.
TRANSMISSION FLUID CHECK 6F50/6F55 T ransmission W ARNING: The dipstick cap and surrounding components may be hot; gloves are recommended. W ARNING: Use gloves when moving the air filter assembly; components will be hot. Note: Automatic transmission fluid expands when warmed.
Moving the Air Filter Assembly (EcoBoost engine) W ARNING: Do not run engine with the air filter disconnected. 1. Shut the engine off. 2. Clean the area around the clamp that connects the air filter assembly to the rubber hose (1). 3. Remove the bolt cover (if equipped).
7. W ithout disconnecting the sensor (4), pull the air filter assembly up to disconnect the air filter assembly from the seated grommets located underneath the air filter assembly . 8. Rotate the air filter assembly 90 degrees counterclockwise and reinstall into the rubber hose.
High fluid level If the fluid level is above the MAX range of the dipstick, remove fluid to reach the hashmark level. Note: Fluid level above the MAX level may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
4. Seat the air filter assembly back into the grommets by pushing down on the air filter assembly . 5. T ighten the clamp. 6. Install and tighten two bolts that attach air filter assembly to the front of the vehicle. 7. Install the bolt cover (if equipped).
CHANGING THE VEHICLE BA TTERY W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes.
If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. Y ou can neutralize the acid with a solution of baking soda and water . It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.
CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimum performance.
Refer to Scheduled Maintenance for the appropriate intervals for changing the air filter element. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.
6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing. ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.
On the wall or screen you will observe a flat zone of high intensity light located at the top of the right hand portion of the beam pattern. If the top edge of the high intensity light zone is not at the horizontal reference line, the headlamp will need to be adjusted.
These are examples of unacceptable moisture (usually caused by a lamp water leak): • W ater puddle inside the lamp. • Large water droplets, drip marks or streaks present on the interior of the lens. T ake your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present.
Replacing high-mount brake lamp bulbs Y our vehicle is equipped with an LED center high-mount stop lamp. It is designed to last the life of the vehicle. If replacement is required, it is recommended that you see your authorized dealer . Replacing license plate lamp bulbs 1.
BULB SPECIFICA TION CHART Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility .
GENERAL INFORMA TION Y our Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following p.
• Note: Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash it off as soon as possible.
W AXING Regular waxing is necessary to protect the paint on your car from the elements. W e recommend that you wash and wax the painted surface once or twice a year . When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Always wash your vehicle before applying wax.
• Spray Motorcraft Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo. • Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage.
CLEANING THE INTERIOR W ARNING: Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. W ARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents.
• Be certain to wash or wipe your hands clean if you have been in contact with certain products, such as insect repellent and suntan lotion, in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.
CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner , metal cleaner or polish on wheels and wheel covers. A clearcoat paint finish coats aluminum wheels and wheel covers. In order to maintain their condition: • Clean weekly with Motorcraft Wheel and Tire Cleaner .
Body • W ash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear -wheel housing and underside of front fenders. • Periodically wash vehicles stored in exposed locations. • T ouch up raw or primed metal to prevent rust.
Brakes • Make sure brakes and parking brake are fully released. T ires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 meters) every 15 days to lubricate working parts and prevent corrosion.
TIRE CARE Information About Uniform Tire Quality Grading T ire Quality Grades apply to new pneumatic passenger car tires. The T ire Quality Grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
Traction AA A B C W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. The traction grades, from highest to lowest are AA, A, B, and C.
• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 42 psi (2.9 bar). Increasing the inflation pressure beyond this pressure will not increase the tire’ s load-carrying capability . • kPa: Kilopascal, a metric unit of air pressure.
Information on P Type Tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
G. H: Indicates the tire’ s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure.
J. T ire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber -coated fabric in the tire tread and sidewall. T ire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester , and others.
Additional Information Contained on the Tire Sidewall for L T Type Tires L T type tires have some additional information beyond those of P type tires. These differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on T T ype Tires T type tires have some additional information beyond those of P type tires. These differences are described below . T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
INFLA TING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required.
Maximum Inflation Pressure is the tire manufacturer’ s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire.
Note: Some spare tires operate at a higher inflation pressure than the other tires. For T -type mini-spare tires, see the Dissimilar Spare T ire and Wheel Assembly Information section.
Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed or suspected, have the tire inspected by a tire professional.
Tire Replacement Requirements W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford.
W ARNING: T o reduce the risk of serious injury , when mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
Safety Practices W ARNING: If your vehicle is stuck in snow , mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. W ARNING: Do not spin the wheels at over 35 mph (56 km/h).
Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you are driving, the wheels may be out of alignment.
USING SNOW CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death.
Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
Changing Tires with a Tire Pressure Monitoring System Note: Each road tire is equipped with a tire pressure sensor located inside the tire and wheel assembly cavity . The pressure sensor is attached to the valve stem. The pressure sensor is covered by the tire and is not visible unless the tire is removed.
When Y ou Believe Y our System Is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air .
Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When Y our T emporary Spare T ire is Installed in this section.
CHANGING A ROAD WHEEL W ARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However , if you must use a sealant, have an authorized dealer install a new tire pressure monitoring system sensor and valve stem.
2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS TIRE AND WHEEL FOR TEMPORARY USE ONL Y When driving with one of the dissimilar spare tires listed above, do not: • exceed 50 mph (80 km/h).
• W inter weather driving capability • W et weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly , additional caution should be given to: • towing a trailer .
W ARNING: Always use the jack provided as original equipment with your vehicle. If using a jack other than the one provided as original equipment with your vehicle, make sure the jack capacity is adequate for the vehicle weight, including any vehicle cargo or modifications.
3. The vehicle jacking points are shown here, and are depicted on the yellow warning label on the jack. Note: Jack at the specified locations to avoid damage to the vehicle. 4. Small arrow-shaped marks on the sills show the location of the jacking points.
Stowing the flat tire 1. Remove the extension bolt from the exterior pocket of the felt bag. 2. Insert the straight end of the jack retention bracket through the eyelet of the angled bracket and swing the retention bracket over the jack.
TECHNICAL SPECIFICA TIONS Wheel Lug Nut T orque Specifications W ARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel.
ENGINE SPECIFICA TIONS Engine 3.7L V6 engine 3.5L V6 EcoBoost engine Cubic inches 226 214 Fuel See Octane recommendations in the Fuel and Refueling chapter . See Octane recommendations in the Fuel and Refueling chapter . Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Spark plug gap 0.
TECHNICAL SPECIFICA TIONS Items Capacity Ford part name or equivalent Ford part number / Ford specification Brake fluid 1 Between MAX and MIN on reservoir Motorcraft DOT 4 L V High Performance Motor V.
Items Capacity Ford part name or equivalent Ford part number / Ford specification Engine oil 5,6 3.7L V6 engine 6.0 qt (5.7L) Motorcraft SAE 5W -20 Motor Oil or equivalent WSS-M2C945-A 3.5L V6 EcoBoost engine 6.0 qt (5.7L) Motorcraft SAE 5W -30 Motor Oil or equivalent WSS-M2C946-A Engine coolant 7 11.
Items Capacity Ford part name or equivalent Ford part number / Ford specification 1 Ford recommends using Motorcraft (Ford) DOT 4 L V High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards.
Motorcraft part numbers Component 3.7L V6 engine 3.5L V6 EcoBoost engine Air filter element F A-1884 F A-1884 Battery BXT -65-650 BXT -65-650 Oil filter FL-500-S FL-500-S Spark plugs SP-520 1 SP-534 1.
The V ehicle Identification Number (VIN) contains the following information: A. W orld manufacturer identifier B. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location C. Make, vehicle line, series, body type D. Engine type E.
TRANSMISSION CODE DESIGNA TION Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents.
ACCESSORIES For a complete listing of the accessories that are available for your vehicle, please contact an authorized dealer or visit our online store at: www .
accessories to Lincoln Motor Company engineering requirements. Contact an authorized Lincoln dealer for the manufacturer’ s limited warranty details, and request a copy of the Lincoln Licensed Accessories product limited warranty from the accessory manufacturer .
FORD ESP EXTENDED SERVICE PLANS PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REP AIRS WITH A FORD EXTENDED SERVICE PLAN. SERVICE PLANS (U.S. only) More than 32 Million Ford and Lincoln owners have discovered the powerful protection Ford ESP .
Roadside Assistance Exclusive 24/7 roadside assistance, including: • T owing, flat-tire change and battery jump starts • Out of fuel and lock-out assistance • T ravel Expense reimbursement for l.
Complete the information below and mail to: Ford ESP PO Box 8072 Royal Oak Michigan 48068-0039 T o learn more, call our Ford ESP specialists at 800-367-3377. Don’t forget to ask about our interest free payment program, allowing you all the security and benefits Ford ESP has to offer while paying over time.
GENERAL INFORMA TION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.
MP3 T rack and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracks and folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode.
AM/FM/CD PREMIUM AUDIO SYSTEM W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
D. TUNE + and TUNE - : • In radio mode, press these buttons to manually search through the radio frequency band. • In Sirius mode, press these buttons to find the next or previous available satellite radio station.
INTRODUCTION W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
Note: Some features are not available while your vehicle is moving. Note: Y our system is equipped with a feature that allows you to access and control audio features for 30 minutes after you switch the ignition off (and no doors open).
SETTINGS Press to select any of the following: • Clock • Display • Sound • V ehicle • Settings • Help HOME Press to access your home screen. Depending on your vehicle’ s option package and software, your screens may vary in appearance from the descriptions in this section.
Using the T ouch-sensitive Controls on Y our System T o turn a feature on and off, just touch the graphic with your finger . T o get the best performance from the touch-sensitive controls, keep in mind: • Do not press hard on the controls. They are sensitive to light touch.
Support The SYNC support team is available to help you with any questions you cannot answer on your own. Monday-Saturday , 8:30am-9:00pm EST . Sunday , 10:30am-7:30pm EST . In the United States, call: 1–800–392–3673. In Canada, call: 1–800–565–3673.
Speed-restricted Features Some features of this system may be too difficult to use while your vehicle is moving so they are restricted from use unless your vehicle is stationary . • Screens that are too crowded with information, such as Point of Interest reviews and ratings, Sirius T ravel Link sports scores, movie times and ski conditions.
Privacy Information When a cellular phone is connected to SYNC, the system creates a profile within your vehicle that is linked to that cellular phone. This profile is created in order to offer you more cellular features and to operate more efficiently .
ACCESSING AND ADJUSTING MODES THROUGH YOUR RIGHT VEHICLE INFORMA TION DISPLA Y The display is located on the right side of your instrument cluster . Y ou can use your steering wheel controls to view and make minor adjustments to active modes without taking your hands off the wheel.
Audio Sources and Memory Presets Use the OK and arrow buttons on the right side of your steering wheel to scroll through the available modes. Y ou can make selections from the menu by using the OK button. The selection menu expands and different options appear .
How to Use V oice Commands with Y our System Press the voice icon. After the tone, speak your command clearly . These commands can be said at any time.
Accessing a List of Available Commands • If you use the touchscreen, press the Settings icon > Help > V oice Command List. • If you use the steering wheel control, press the voice icon.
Confirmation Prompts: The system uses these short questions to confirm your voice request. If turned off, the system simply makes a best guess as to what you requested. The system may still occasionally ask you to confirm settings. Phone/Media Candidate Lists: Candidate lists are lists of possible results from your voice commands.
ENTERT AINMENT A. AM 1 and AM AST B. FM 1, FM 2 and FM AST C. SIRIUS D. CD E. USB F . T ouch this button to scroll down for more options, such as: • SD Card • BT Stereo • A/V In G. These buttons change with the media mode you are in. H. Radio memory presets and CD controls.
Browsing Device Content When listening to audio on a device, you can browse through other devices without having to change sources. For example, if you are currently listening to audio on an SD card, you can browse all the artists that are stored on your USB device.
.
Scan T ouch this button to go to the next strong AM or FM radio station. The light on the button illuminates when the feature is on. Options Sound Settings allows you to adjust settings for: • Bass • Midrange • T reble • Balance and Fade • DSP (Digital Signal Processing) • Occupancy Mode • Speed Compensated V olume.
HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Y our system has a special receiver that allows it to receive digital broadcasts (where available) in addition to the analog broadcasts, it already receives.
When HD Radio broadcasts are active, you can access the following functions: • Scan allows you to hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels.
In order to provide the best possible experience, use the contact form to report any station issues found while listening to a station broadcasting with HD Radio technology . Independent entities own and operate each station. These stations are responsible for making sure all audio streams and data fields are accurate.
* http://www .ibiquity .com/automotive/report_radio_station_experiences HD Radio T echnology manufactured under license from iBiquity Digital Corp. U.S. and foreign patents. HD Radio and the HD and HD Radio logos are proprietary trademarks of iBiquity Digital Corp.
“TUNE” “AM <530–1710>” “FM 1 preset <#>” “AM autoset” “FM2” “AM autoset preset <#>” “FM 2 preset <#>” “AM preset <#>” “HD <#>” * “FM” “Preset <#>” “FM <87.9–107.
Options Sound Settings allows you to adjust settings for: • Bass • Midrange • T reble • Balance and Fade • DSP (Digital Signal Processing) • Occupancy Mode • Speed Compensated V olume. Note: Y our vehicle may not have all these sound settings.
Browse T ouch this button to view a list of all available stations. Scroll to see more categories. T ouch the station you want to listen to. T ouch Skip if you want to skip this channel. T ouch Lock if you do not want anyone to listen to this channel.
“TUNE” “Sirius <0–223>” “<Channel name>” “Preset <#>” “SA T” “SA T 1” “SA T 1 preset <#>” “SA T 2” “SA T 2 preset <#>” “SA T 3” .
Potential satellite radio reception issues Antenna obstructions For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other materials as far away from the antenna as possible.
Sirius troubleshooting tips Radio display Condition Possible action Unsubscribed Channel. Y our subscription does not include this channel. Contact Sirius at 1–888–539–7474 to subscribe to the channel, or tune to another channel. No Signal. The signal is lost from the Sirius satellite or Sirius tower to your vehicle antenna.
Repeat T ouch this button to repeat the currently playing track, all tracks on the disc or turn the feature off if already on. Shuffle T ouch this button to play the tracks or entire albums in random order , or turn the feature off if already on. Scan T ouch this button to hear a brief sampling of all available tracks.
If you are not listening to a CD, press the voice button and, after the tone, say “CD”, then any of the commands in the following chart. “CD” “Pause” “Repeat off” “Play” “Repeat .
USB Port The ports are located either in the center console or behind a small access door in the instrument panel. T o access and play music from your device, press the lower left corner of the touchscreen, and then select the USB tab.
Note: Y our vehicle may not have all these sound settings. • Media Player Settings allows you to select more settings, which is under Media Player . See Settings. • Device Information displays software and firmware information about the currently connected media device.
“USB” or “SD CARD” “Play movie <name>” ** “Repeat one” “Play music video <name>” ** “Shuffle” “Play next song” “Shuffle off” “Play playlist <name>.
Supported Media Players, Formats and Metadata Information SYNC is capable of hosting nearly any digital media player , including iPod®, Zune™, plays from device players, and most USB drives. Supported audio formats include MP3, WMA, W A V and AAC. It is also able to organize your indexed media from your playing device by metadata tags.
W ARNING: For safety reasons, do not connect or adjust the settings on your portable music player while your vehicle is moving. W ARNING: Store the portable music player in a secure location, such as the center console or the glove box, when your vehicle is in motion.
5. T urn the portable music player on and adjust the volume to 1 ⁄ 2 the maximum. 6. Press the lower left corner on the touchscreen. Select the A/V In tab.
PHONE A. Phone B. Quick Dial C. Phonebook D. History E. Messaging F . Settings Hands-free calling is one of the main features of SYNC. Once you pair your phone, you can access many options using the touchscreen or voice commands. While the system supports a variety of features, many are dependent on your cellular phone’ s functionality .
Pairing Y our Phone for the First Time W ARNING: Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
3. If you are prompted to enter a PIN on your device, it does not support Secure Simple Pairing. T o pair , enter the PIN displayed on the touchscreen. Skip the next step. 4. When prompted on your phone’ s display , confirm that the PIN provided by SYNC matches the PIN displayed on your cellular phone.
Phonebook T ouch this button to access and call any contacts in your previously downloaded phone book. The system places the entries in alphabetical categories summarized at the top of the screen.
Composing a T ext Message Note: This is a speed-dependent feature. It is unavailable when your vehicle is traveling at speeds over 3 mph (5 km/h). Note: Downloading and sending text messages using Bluetooth are phone-dependent features. 1. T ouch the top left corner of the display to access the Phone menu.
Receiving a T ext Message When a new message arrives, an audible tone sounds and the screen displays a pop-up with the caller name and ID, if supported by your phone. Y ou can press: • Vi e w to view the text message. • Listen for SYNC to read the message to you.
Internet Data Connection If your phone is compatible, use this screen to adjust your internet data connection. Select to make your connection profile with the personal area network or to turn off your connection. Y ou can also choose to adjust your settings or have the system always connect, never connect when roaming or query on connect.
“MESSAGES” “Call” “Forward text messages” “Listen to text message <#>” “Listen to text messages” “Reply to text messages” “Help” INFORMA TION If your vehicle is equipped with Navigation, touch the i (Information) button to access these features.
SYNC Services (If Equipped, United States Only) Note: SYNC Services varies by trim level and model year and may require a subscription. T raffic alerts and turn-by-turn directions available in select markets.
Connecting to SYNC Services Using V oice Commands Press the voice button on the steering wheel controls. 1. When prompted, say “Services”. This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabled cellular phone.
If your vehicle is not equipped with Navigation: • T urn-by-turn directions appear in the information display , in the status bar of your touchscreen system and on the SYNC Services screen. Y ou also receive driving instructions from audible prompts.
SYNC Services quick tips Portable Y our subscription is associated with your Bluetooth-enabled cellular phone number , not your VIN (V ehicle Identification Number). Y ou can pair and connect your phone to any vehicle equipped with SYNC Services and continue enjoying your personalized services.
Note: Visit www .siriusxm.com/traffic# and click on Coverage map and details for a complete listing of all traffic areas covered by Sirius T ravel Link. Note: Neither Sirius nor Ford is responsible for any errors or inaccuracies in the Sirius T ravel Link services or its use in vehicles.
Sirius Travel Link V oice Commands Note: In order to use Sirius T ravel Link, your vehicle must be equipped with navigation and your navigation SD card must be in the SD card slot.
“TRA VEL LINK” “College basketball schedule” “Motor sports order” “NHL schedule” “College basketball scores” “Motor sports schedule” “NHL scores” “College football headli.
91 1 Assist® (If Equipped) W ARNING: Unless the 911 Assist setting is set on before a crash, the system will not dial for help, which could delay response time, potentially increasing the risk of serious injury or death after a crash. W ARNING: Do not wait for 911 Assist to make an emergency call if you can do it yourself.
Setting 91 1 Assist On If your vehicle is equipped with Navigation, touch the i (Information) button to access these features. If your vehicle is not equipped with Navigation, touch the corner of the touchscreen with the green tab. Press Apps > 911 Assist, > On.
If you do not cancel the call, and SYNC makes a successful call, a pre-recorded message plays for the 911 operator , and then the occupant(s) in your vehicle is able to talk with the operator .
Note: In order to allow a break-in period for your vehicle, you may not be able to create a V ehicle Health Report until your vehicle odometer has reached 200 miles. Note: Cellular phone and SMS charges may apply when making a report. Register for V ehicle Health Report and set your report preferences at www .
SETTINGS A. Clock B. Display C. Sound D. V ehicle E. Settings F . Help Under this menu, you can set your clock, access and adjust the display , sound and vehicle settings as well as access settings for specific modes or the help feature. Clock Note: Y ou cannot manually set the date.
Y ou can also turn the outside air temperature display on and off. It appears at the top center of the touchscreen, next to the time and date. The system automatically saves any updates you make to the settings.
Only the photograph(s), which meets the following conditions, display: • Compatible file formats are as follows: .jpg, .gif, .png, .bmp. • Each file must be 1.
Door Keypad Code T o change the keypad code for your keyless entry keypad system: 1. Press the Settings icon > V ehicle > Door Keypad Code. 2. Enter your current factory code, then, when prompted, enter your new code. Rear V iew Camera This menu allows you to access settings for your rear view camera.
System T ouch Screen Button Beep Select to have the system beep to confirm choices made through the touchscreen. T ouch Panel Button Beep Select to have the system beep to confirm button choices made through the climate or audio system. Keyboard Layout Have the touchscreen keyboard display in QWERTY or ABC format.
Media Player Press the Settings icon > Settings > Media Player , then select from the following: Media player Autoplay When this feature is on, the system automatically switches to the media source upon initial connection. This allows you to listen to music during the indexing process.
Navigation Press the Settings icon > Settings > Navigation, then select from the following: Navigation Map Preferences T urn breadcrumbs on and off. Have the system display your turn list top to bottom or bottom to top. T urn the Parking POI notification on and off.
Navigation T raffic Preferences Have the system display areas where roadwork occurs. Have the system display incident icons. Have the system display areas where difficult driving conditions may occur . Have the system display areas where snow and ice on the road may occur .
Phone Phone Ringer Select the type of notification for phone calls - ring tone, beep, text to speech, or have it be silent. T ext Message Notification Select the type of notification for text messages - alert tone, beep, text to speech, or have it be silent.
W ireless & Internet W i-Fi Settings W i-Fi Network (Client) Mode turns the W i-Fi feature on and off in your vehicle. Make sure you turn it on for connectivity purposes. Choose a W ireless Network allows you to use a previously stored wireless network.
W ireless & Internet USB Mobile Broadband Instead of using W i-Fi, your system can also use a USB mobile broadband connection to access the internet. (Y ou must turn on your mobile broadband device on your personal computer before connecting it to the system.
Help Press the Settings icon > Help, then select from the following: Help Where Am I? V iew your vehicle’ s current location, if your vehicle is equipped with navigation. If your vehicle is not equipped with navigation, nothing displays. System Information T ouchscreen system serial number .
T o access Help using the voice commands, press the voice button, then, after the tone, say “Help”. The system provides allowable voice commands for the current mode. CLIMA TE Press the lower right corner on the touchscreen to access your climate control features.
E. MAX A/C: T ouch to cool your vehicle with recirculated air . T ouch again for normal A/C operation. MAX A/C: • Distributes air through instrument panel vents. • Is more economical and efficient than normal A/C mode. • May help reduce odors from entering your vehicle.
• T ouch and hold MyT emp to select a temperature you would like your vehicle to remember and maintain for you. • If your vehicle is equipped with a heated steering wheel, touch the heated steering wheel icon to warm the steering wheel.
Additional climate control voice commands “Max A/C on” “T emperature increase” “My temp” “T emperature low” “Off” “W indshield floor on” “On” “Help” “Panel floor on” * If you have said “T emperature”, you can say any of the commands in the following “T emperature” chart.
Setting a Destination Press the green corner of your touchscreen, then Dest when it appears. Choose any of the following: Destination selections My Home Street Address Favorites Intersection Previous Destinations City Center Point of Interest Map Emergency Edit Route Cancel Route 1.
Point of Interest (POI) Categories Y our system offers a variety of points of interest categories. Main categories Food/Drink & Dining Automotive T ravel & T ransportation Shopping Financial E.
cityseekr (If Available) Note: cityseekr point of interest information is limited to approximately 912 cities (881 in the United States, 20 in Canada and 11 in Mexico). cityseekr , when available, is a service that provides more information about certain points of interest such as restaurants, hotels and attractions.
Attraction This icon appears when your selection exists in multiple categories within the system. When you are viewing more information for hotels, cityseekr also tells you if the hotel has certain services and facilities using icons.
Map Preferences Breadcrumbs displays your vehicle’ s previously traveled route with white dots. T urn this feature ON or OFF . T urn List Format allows you to choose to have the system display your turn list T op to Bottom or Bottom to T op. Parking POI Notification sets the automatic parking points of interest notification.
Traf fic Preferences A void T raf fic Problems allows you to choose how you want the system to handle traffic problems along your route. • Automatic: Have the system reroute you to avoid traffic incidents that develop and impact the current route. The system does not provide a traffic alert notification.
3D landmarks appear as clear , visible objects that are typically recognizable and have a certain tourist value. The 3D landmarks appear in 3D map mode only . Coverage varies, and improves with updated map releases. Change the appearance of the map display by repeatedly pressing the arrow button in the upper left corner of the screen.
Auto Zoom Press the green bar to access map mode, then select the + or - zoom button to bring up the zoom level and Auto buttons on the touchscreen. When you press Auto, Auto Zoom turns on and Auto displays in the bottom left corner of the screen in the map scale.
W aypoints indicates the location of a waypoint on the map. The number inside the circle is different for each waypoint and represents the position of the waypoint in the route list. Destination symbol indicates the ending point of a planned route. Next maneuver point indicates the location of the next turn on the planned route.
V iew/Edit Route Access these features when a route is active: • View Route • Edit Destination/W aypoints • Edit T urn List • Detour • Edit Route Preferences • Edit T raffic Preferences • Cancel Route. Nokia is the digital map provider for the navigation application.
Navigation system voice commands “Destination nearest POI” “Show turn list” 1 “Destination play nametags” “V oice guidance off” “Destination POI” “V oice guidance on” “Destin.
“NA VIGA TION” “Zoom state” “Zoom street” “Zoom to <distance>” “Help” * If you have said, “Destination”, you may say any of the commands in the Destination chart.
GENERAL INFORMA TION SYNC® End User License Agreement (EULA) • Y ou have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMP ANY from an affiliate of Microsoft Corporation (“MS”).
DESCRIPTION OF OTHER RIGHTS AND LIMIT A TIONS: • Speech Recognition: If the SOFTW ARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process.
• Security Updates/Digital Rights Management: Content owners use the WMDRM technology included in your DEVICE to protect their intellectual property , included copyrighted content. Portions of the SOFTW ARE on your DEVICE use WMDRM software to access WMDRM-protected content.
If FORD MOTOR COMP ANY or third party software and services suppliers provide or make available to you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of this EULA shall apply .
INTELLECTUAL PROPER TY RIGHTS: All title and intellectual property rights in and to the SOFTW ARE (including but not limited to any images, photographs, animations, video, audio, music, text and “ap.
No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LA W , FORD MOTOR COMP ANY , ANY THRID P ARTY SOFTW ARE OR SERVICES SUPPLIERS, MS, MICROSOFT CORPORA TION AND THEIR AFFILIA TES SHALL HA VE NO.
W ARNING: Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences. Do not change system settings or enter data non-verbally (using your hands) while driving.
Distraction Hazard Any navigation features may require manual (non-verbal) setup. Attempting to perform such set-up or insert data while driving can seriously distract your attention and could cause an accident or other serious consequences. Stop the vehicle in a safe and legal manner before attempting these operations.
These terms and conditions represent the agreement (“Agreement”) between you and T elenav , Inc. (“T elenav”) with respect to the T elenav Software (including upgrades, modifications, or additions thereto) (collectively “T elenav Software”).
3. Software License Subject to your compliance with the terms of this Agreement, T elenav hereby grants to you a personal, non-exclusive, non-transferable license (except as expressly permitted below .
or functionality of the T elenav Software are not intended to support such high risk applications, especially in more remote geographical areas. TELENA V EXPRESSL Y DISCLAIMS AND EXCLUDES ALL W ARRANT.
jurisdiction. Note that there is no judge or jury in an arbitration proceeding and the decision of the arbitrator shall be binding upon both parties. Y ou expressly agree to waive your right to a jury trial.
8.4 T elenav’ s or your failure to require performance of any provision shall not affect that party’ s right to require performance at any time thereafter , nor shall a waiver of any breach or default of this Agreement constitute a waiver of any subsequent breach or default or a waiver of the provision itself.
The Data is provided for your personal, internal use only and may not be resold. It is protected by copyright, and is subject to the following terms (this “End User License Agreement”) and conditions which are agreed to by you, on the one hand, and HERE and its licensors (including their licensors and suppliers) on the other hand.
This Data may contain inaccurate or incomplete information due to the passage of time, changing circum-stances, sources used and the nature of collecting comprehensive geographic Data, any of which may lead to incorrect results. No W arranty: This Data is provided to you “as is”, and you agree to use it at your own risk.
Export Control: Y ou agree not to export from anywhere any part of the Data or any direct product thereof except in compliance with, and with all licenses and approvals required under , applicable exp.
Government End Users: If the Data is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, this Data is a “commercial item” as that term is defined at 48 C.
Gracenote® End User License Agreement (EULA) This device contains software from Gracenote, Inc. of 2000 Powell Street Emeryville, California 94608 (“Gracenote”).
Gracenote uses a unique identifier to track queries for statistical purposes. The purpose of a randomly assigned numeric identifier is to allow Gracenote to count queries without knowing anything about who you are. For more information, see the web page at www .
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
GENERAL MAINTENANCE INFORMA TION Why Maintain Y our V ehicle? Carefully following the maintenance schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may help to increase the value of your vehicle when you sell or trade it.
Convenience Many dealerships have extended evening and Saturday hours to make your service visit more convenient and they offer one stop shopping. They can perform any services that are required on your vehicle, from general maintenance to collision repairs.
Ford strongly recommends the use of only genuine Ford, Motorcraft or Ford-authorized remanufactured replacement parts because they are engineered for your vehicle. Additives and Chemicals Ford Motor Company recommended additives and chemicals are listed in the owner manual and in the Ford W orkshop Manual.
Check every six months Parking brake for proper operation. Safety belts and seat latches for wear and function. Safety warning lamps (brake, ABS, airbag, safety belt) for operation. W asher spray and wiper operation. Clean or replace blades as necessary .
Scheduled Maintenance 447 2014 MKS (mks) Owners Guide gf, 2nd Printing, December 2013 USA (fus).
NORMAL SCHEDULED MAINTENANCE AND LOG Intelligent Oil-Life Monitor® Y our vehicle is equipped with an Intelligent Oil-Life Monitor that determines when the engine oil needs to be changed based on how your vehicle is used.
Normal scheduled maintenance * At every oil change interval as indicated by the information display Change engine oil and filter . ** Rotate tires, inspect tire wear and measure tread depth. Perform multi-point inspection (recommended). Inspect automatic transmission fluid level.
Other maintenance items 1 Every 20000 miles (32000 km) Replace cabin air filter . Every 30000 miles (48000 km) Replace climate-controlled (heated and cooled) seat filter . 2 Replace engine air filter . At 100000 miles (160000 km) Change engine coolant.
Maintenance Schedule Log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A .
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
SPECIAL OPERA TING CONDITIONS If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance.
Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery , taxi, patrol car or livery) As required Change engine oil and filter as indicated by the information display and perform services listed in the Normal Scheduled Maintenance chart.
Special Operating Condition Log D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P.
D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D AT E :M ILEAGE : D EALER V ALIDA TION : P&A C ODE : RO#: H OURS : D A.
EXCEPTIONS There are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks e.
Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent on exposure to dusty and dirty conditions. V ehicles operated in these conditions require frequent inspection and replacement of the engine air filter and cabin air filter .
911 Assist™ .............................. 391 A ABS (see Brakes) ..................... 181 Accessing and using your USB port ....................................369 Accessing your calendar ..........390 Accessory delay ..........................98 Active Park Assist .
CD player .......................... 338, 367 CD voice commands .................368 Cell phone use ............................16 Changing a tire ......................... 319 Child safety restraints ..........29, 31 Child safety seats attaching with tether straps .
End user license agreement .... 423 Engine ........................................ 326 cleaning ................................... 291 coolant .....................................269 fail-safe cooling .......................273 idle speed control .
Inspection/maintenance (I/M) testing ........................................ 166 Instrument panel cleaning ................................... 293 cluster ...................................... 104 Intelligent Access Key ................ 59 J Jack ..
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lincoln MKS (2014) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lincoln MKS (2014) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lincoln MKS (2014), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lincoln MKS (2014) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lincoln MKS (2014), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lincoln MKS (2014).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lincoln MKS (2014). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lincoln MKS (2014) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
