Manuel d'utilisation / d'entretien du produit IM730 du fabricant Lincoln Electric
Aller à la page of 54
Ranger 305 D OPERA TOR’S MANUAL IM730 August, 2004 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page Installation ................................................................................................................... ....Section A Technical Specifications .....................................................
vii T ABLE OF CONTENTS Maintenance ......................................................................................................Section D Safety Precautions .....................................................................................
RANGER 305D 1. Output rating in watts is equivalent to volt-amperes at unity power factor. Output voltage is within ± 10% at all loads up to rated capacity. When welding, available auxiliary power will be reduced. * Top of enclosure add 6in. (152mm) for exhaust pipe.
LIFTING The RANGER 305D weighs approximately 775lbs.(352kg.) with a full tank of fuel. A lift bail is mounted to the machine and should always be used when lifting the machine. • Lift only with equipment of ade- quate lifting capacity. • Be sure machine is stable when lift- ing.
A-3 INST ALLA TION RANGER 305D A-3 TOWING The recommended trailer for use with this equipment for road, in-plant and yard towing by a vehicle(1) is Lincoln’s K957-1. If the user adapts a non-Lincoln trailer, he must assume responsi- bility that the method of attachment and usage does not result in a safety hazard nor damage the welding equipment.
A-4 INST ALLA TION RANGER 305D A-4 SP ARK ARRESTER Some federal, state or local laws may require that gasoline or diesel engines be equipped with exhaust spark arresters when they are operated in certain locations where unarrested sparks may present a fire hazard.
The 240 VAC output can be split to provide two sepa- rate 120 VAC outputs with a max permissible current of 44 Amps per output to two separate 120 VAC branch circuits (these circuits cannot be paralleled). Output voltage is within ± 10% at all loads up to rated capacity.
A-6 INST ALLA TION RANGER 305D A-6 CONNECTION OF RANGER 305D T O PREMISES WIRING W ARNING • Only a licensed, certified, trained electrician should install the machine to a premises or residential electrical system. Be certain that: • The installation complies with the National Electrical Code and all other applicable electrical codes.
A-7 INST ALLA TION RANGER 305D A-7 CONNECTION OF LINCOLN ELECTRIC WIRE FEEDERS Connection of LN-7 or LN-8 to the RANGER 305D • Shut the welder off. • Connect the LN-7 or LN-8 per instructions on the appropriate connection diagram in Section F.
A-8 INST ALLA TION RANGER 305D A-8 Connection of PRINCE XL SPOOL GUN to the Ranger 305D Connection of the Prince XL Spool Gun requires the use of the K1849-1 Adapter Module.
B-1 OPERA TION RANGER 305D B-1 SAFETY PRECAUTIONS Do not attempt to use this equipment until you have thoroughly read the engine manufacturer ’ s manual sup- plied with your welder. It includes important safety pre- cautions, detailed engine starting, operating and main- tenance instructions, and parts lists.
B-2 OPERA TION B-2 WELDING CONTROLS (Figure B.1) 1. OUTPUT CONTROL: The OUTPUT dial is used to preset the output voltage or current as dis- played on the digital meters for the four welding modes.
B-3 OPERA TION B-3 4. ARC CONTROL : The ARC CONTROL dial is active in the CV-WIRE, CC-STICK and DOWNHILL PIPE modes, and has different functions in these modes.
B-4 OPERA TION B-4 15. ENGINE AL TERNA TOR TROUBLE LIGHT -The engine alternator light is off when battery charging system is functioning normally. If light turns on, the alternator or the voltage regulator may not be operating correctly. The light may also come on due to the battery not holding a charge.
TYPICAL CURRENT RANGES (1) FOR TUNGSTEN ELECTRODES (2) Tungsten Electrode DCEN (-) DCEP (+) Approximate Argon Gas Flow TIG TORCH Diameter in. (mm) Flow Rate C.F.H. ( l /min.) Nozzle Size (4), (5) 1%, 2% Thoriated 1%, 2% Thoriated Aluminum Stainless Steel Tungsten Tungsten .
RANGER 305D B-6 OPERA TION B-6 When in the TOUCH START TIG mode and when a Amptrol is connected to the 6-pin Connector the OUT- PUT dial is used to set the maximum current range of the CURRENT CONTROL of the Amptrol. The ARC CONTROL is not active in the TIG mode.
Permissible Auxiliary Current in -Amps @ 240 VAC 44 31 24 19 12 3 B-7 OPERA TION B-7 AUXILIAR Y POWER: Start the engine and set the IDLER control switch to the desired operating mode. Full power is available regardless of the welding control settings providing no welding current is being drawn.
C-1 ACCESSORIES C-1 FIELD INST ALLED OPTIONS / ACCESSORIES K957-1 HEAVY DUTY, TWO WHEEL TRAILER FOR SMALL WELDERS For road, off-road and in-plant and yard towing. (For highway use, consult applicable federal, state and local laws regarding requirements for brakes, lights, fenders, etc.
D-1 MAINTENANCE D-1 RANGER 305D SAFETY PRECAUTIONS • Have qualified personnel do all maintenance and troubleshooting work. • Turn the engine off before working inside the machine or servicing the engine. • Remove guards only when necessary to perform maintenance and replace them when the mainte- nance requiring their removal is complete.
D-2 MAINTENANCE D-2 Engine Oil Change Drain the engine oil while the engine is warm to assure rapid and complete draining. • Be sure the unit is off. Disconnect the negative bat- tery cable to ensure safety. • Locate oil drain hose and valve in bottom of base and pull through the hole in the battery access panel on the welder.
D-3 MAINTENANCE D-3 RANGER 305D Service Instructions & Installation T ips For Engine Air Filter Release the 1 Seal Carefully Unlatch and remove the service cover of the air cleaner. Make certain the latches are folded back against the cover so that they donít hinder filter removal/installation.
D-4 MAINTENANCE D-4 COOLING SYSTEM HOT COOLANT can burn skin. • Do not remove cap if radiator is hot. ------------------------------------------------------------------------ Check the coolant level by observing the level in the radiator and recovery bottle.
D-5 MAINTENANCE D-5 FUEL FIL TER 1 . Check the fuel filter and fuel pre-filter for water accumulation or sediment. 2. Replace the fuel filter if it is found with excessive water accumulation or sediment.
D-6 MAINTENANCE D-6 RANGER 305D WELDER / GENERA T OR MAINTENANCE STORAGE: Store the RANGER 305D in clean, dry protected areas. CLEANING: Blow out the generator and controls peri- odically with low pressure air. Do this at least once a week in particularly dirty areas.
E-1 TROUBLESHOOTING E-1 RANGER 305D If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 RANGER 305D Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 RANGER 305D Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-4 TROUBLESHOOTING E-4 RANGER 305D Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-5 TROUBLESHOOTING E-5 RANGER 305D Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-6 TROUBLESHOOTING E-6 RANGER 305D Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIAGRAMS F-1 RANGER 305D.
F-2 DIAGRAMS F-2 RANGER 305D.
F-3 DIAGRAMS F-3 RANGER 305D.
F-4 DIAGRAMS F-4 RANGER 305D.
F-5 DIAGRAMS F-5 RANGER 305D.
F-6 DIAGRAMS F-6 RANGER 305D or ser vice t his equi pm ent. On ly qualified personnel should install,use Keep away from m oving parts. Keep guards in place. MOVING PARTS can injure W ARNING Do not touch electrically live parts. before servicing. Disconnect NEGATIVE (-) Bat te ry lead Do not operate with panels open.
F-7 DIAGRAMS F-7 RANGER 305D.
F-8 DIAGRAMS F-8 RANGER 305D.
F-9 DIAGRAMS F-9 RANGER 305D.
F-10 DIAGRAMS F-10 RANGER 305D.
F-11 DIAGRAMS F-11 RANGER 305D.
F-12 DIAGRAMS F-12 RANGER 305D NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-13 DIAGRAMS F-13 RANGER 305D DIMENSION PRINT RANGER 305D M19772 A.05 *29.0 *11.3 *CE NTER OF GR AVI TY 21.06 51.20 17.50 19.50 35.77 29.83 34.24 6.33 11.
NOTES RANGER 305D.
NOTES RANGER 305D.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE PARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lincoln Electric IM730 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lincoln Electric IM730 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lincoln Electric IM730, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lincoln Electric IM730 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lincoln Electric IM730, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lincoln Electric IM730.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lincoln Electric IM730. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lincoln Electric IM730 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
