Manuel d'utilisation / d'entretien du produit C60K, H60T, H60B, E60B du fabricant Kunz
Aller à la page of 31
60” FINISH CUT C60K H60T 60T H60H H60H E60B E60B OWNER’S MANUAL With Assembly Instructions For Models: C60K, H60T, H60H & E60B KUNZ ENGINEERING, INC.
ASSEMBLY INSTRUCTIONS READ THE COMPLETE ASSEMBLY INSTRUCT IONS BEFORE STARTING THE ASSEMBLY. You should have: - one mower deck assembly - two caster assemblies - two rear axle assemblies - one tongue .
Note: Tighten the four wheel assembly pivot bolts so that the wheel assemblies will not flop down when the deck is raised off the ground. Caster Support Stop Caster Su pport Tongue Figure 2: Installation of Caster Support Stop B.
5. The telescoping hitch can either be installed to the left or right and should clear the back of the tire by about 2”. 6. If one mower is pulled on both the left and righ t side of the tow vehicle, then one telescoping hitch can be mounted to the left and one to the right.
C. INSTALLATION OF ATV TONGUE ASSEMBLY (if the lawn and garden hitching was purchased refer to Section B. Installa tion of Lawn & Garden Hitching) 1. The tongue can be installed ei ther on the left or right cast er assembly depending on how the wing mower will be towed.
A. HITCH CONFIGURATIONS (Refer to Figure 6) Shut off the engine and allo w the mower blades to come to a complete stop before adjusting the spreader hitch on the tow vehicle.
The hitching system is designed so that the wing mower can be pulled directly behind a tow vehicle without a mower deck or as a left or ri ght wing mower when towed behind a tow vehicle with or without a mower deck.
C. ADJUSTING CUTTING HEIGHT Shut off all engines and a llow the mower blades to come to a complete stop on the wing mowers and on the tow vehicle before adjusting the cutting height. The cutting height can be adjusted in a range from 1.0" to 4.0".
4. Adjust the cutting he e height as the tow th Note: To mow in the lower half of the cutting range, set the front caster axles in the bottom ote: After the cutting height has been set, be sure to tighten the pivot bolts securely to yond D. STARTING ENGINE Set parking brake on tow vehicle.
Start engine and move throttle toward slow position to disengage choke. The mower blades clutch will engage as the engine comes up to s peed. The mower blades clutch engages at 1850 RPM. Slow engine speed to idle to allow engine to warm up. This will probabl y allow the mower blade clutch to fully disengage.
For Model H60H: Set the throttle to slow so the mower blades clutch will disengage. Allow engine to cool down for a short ti me before moving the throttle control to the stop position. For Model E60B: Slow the engine speed down and disengage the clutch handle.
Look down, to the sides, and behind before and while backing to avoid backing over something or someone. Care should also be taken while backing so that the wing mower or mow ers do not jackkn ife and damage hitches. Backing up with one wing mower is easy.
G. DRIVE BELT REMOVAL AND TENSION Shut off engine and allo w mower blades to stop turning before making any adjustments or repairs. Remove the safety shields. Loosen the nuts on the spring-loaded idler; adjust t he nut until the belt can be slipped off the idler and drive sheaves.
Front Engine Initial Spring Length 15/16” Running Spring Length 1-1/8” to 1-1/4” Figure 9: Belt Pattern and Sp ring Adjustment (Model C60K) For Model E60B: - See Figure 10. With the clutch engaged, adjust t he nuts on the spring loaded idler adj uster bolt until the length of the spring is between 2-1/4” and 2- 3/8”.
Clutch Engaged Spring Length 2-1/4” to 2-3/8” Clutch Disengaged Spring Length no greater than 2-3/4” 1/2” With Clutch Engaged 0” With Clutch Disengaged Brake Stud Clutch En g a g ement En g ine Clutch Arm Front Figure 10: Belt Pattern and Sp ring Adjustment (Model E60B) H.
I. LUBRICATION There are up to ten lubrication points on the wi ng mower -- one spri ng-loaded idler pivot, two caster wheel pivots, four wheels (on models that apply), and three blade spindles (on models that apply). Lubricate at approximately 10 hr.
WING MOWER SPECIFICATIONS Mode l Model H60T C60 K ENGINE: Engi ne Mak e Tec um seh Enduro Kohl er Com m and Pro Engi ne Model OHV130- EXE CV 15S Cyl i nders 1 1 Cycles 4 4 Crankshaf t Vert i cal V ert i cal Engi ne HP 13 15 Bore 3.31" 3. 55" St roke 2.
WING MOWER SPECIFICATIONS Mode l Model E60B H60H ENGINE: Engi ne Mak e Bri ggs & St rat t on Honda Engi ne Model Inte k GX V3 9 0 Cyl i nders 11 Cycles 44 Crankshaf t Verti cal Vertical Engi ne HP 13 13 Bore 3.44” 3. 46” Stroke 2.26” 2. 52” Di splacem ent 21.
ACREASE WING MOWER PARTS MODEL C60K Item Part # Descript ion C6 0K 1 202135 He x H e ad Bolt , 3/ 8" x 3" Fully Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoul der Length 6 3 222005 W orm Dr i v e Hose Clam p ( 7- 7/ 8" to 9- 1/ 8" Cl am ping Di a.
MODEL C60K 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 21 22 23 24 25 26 27 28 29 30 31 34 33 32 19.
ACREASE WING MOWER PARTS MODEL H60T Item Part # Descript ion H6 0T 1 202135 He x H e ad Bolt , 3/ 8" x 3" Fully Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoul der Length 6 3 222005 W orm Dr i v e Hose Clam p ( 7- 7/ 8" to 9- 1/ 8" Cl am ping Di a.
MODEL H60T 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 21 22 23 24 25 26 27 28 29 30 31 34 33 32 21.
ACREASE WING MOWER PARTS MODEL E60B Item Part # Descripti on E60B 1 202135 He x He ad Bolt, 3/ 8" x 3" Fully Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoulder Length 6 3 225003 Compr ession Spri ng, 3"L x 1-3/32" O .
MODEL E60B 23 1 2 3 9 4 5 6 7 8 10 11 12 16 27 28 17 14 15 22 1 20 18 19 23 24 25 21 26 8 13.
ACREASE WING MOWER PARTS MODEL H60H Item Part # Descripti on Quan tity 1 202135 He x He ad Bolt, 3/ 8" x 3" Full y Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoulder Length 6 3 222005 W or m Drive Hose Clam p ( 7- 7/ 8" t o 9- 1/ 8" Clam ping Di a.
MODEL H60H 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 17 18 19 20 21 22 23 24 25 27 26 28.
PARTS LIST 1 2 4 3 2 5 7 8 10 9 6 LAWN & GARDEN HITCH PARTS Qua ntity Item Part # Descripti on H60T , E 60B & H60H C60 K 1 202135 He x He ad Bolt, 3/ 8" x 3" Fully Thr eade d 2 2 2 2.
ATV TONGUE PARTS PARTS LIST 1 4 2 3 Ite m Part # Descrip t i on Qua ntity 1 216002 W i r e Lock Pi n . 31" X 2. 50" 2 2 216009 Scr ew Pi n Shackl e Cl ev i s 1 3 900057 Hi t ch Pi v ot 1 4 9.
SAFETY SIGNS AND LOCATIONS 275007 – Warning Decal, Belt Shield 275003 – Danger Decal, Cut Hand & Foot 275002 – Warning Decal, General Serial # & Model # Decal Clean or Replace Any Safety Signs That Are not Readable or Damaged Replacement decals can be purchased from your local dealer or Kunz Engineering Inc.
OPTIONAL EQUIPMENT OPTIONAL FLOATATION KIT This optional floatation kit features an extra front and back tire that can be bolted in the center section of the mower deck.
30.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Kunz C60K, H60T, H60B, E60B c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Kunz C60K, H60T, H60B, E60B - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Kunz C60K, H60T, H60B, E60B, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Kunz C60K, H60T, H60B, E60B va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Kunz C60K, H60T, H60B, E60B, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Kunz C60K, H60T, H60B, E60B.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Kunz C60K, H60T, H60B, E60B. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Kunz C60K, H60T, H60B, E60B ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.