Manuel d'utilisation / d'entretien du produit HDP2100 du fabricant Knoll
Aller à la page of 50
H D P2100 High Definition Projector PROJEC T OR User ’ s Manual.
Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the author.
HDP2100 Users Manual — ii — Important Safety Information Important: It is strongly recommended that you read this secti on carefully before using the projector. These safety and usage instructions will ens ure that you enjoy many years of safe use of the projector.
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, other wise lamp life could decrease dramatically.
HDP2100 Users Manual Replacing the Lamp Replacing the lamp can b e hazardous if done in correctly. See Replacing the Proje ction Lamp on page 30 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow the lamp to cool for about one hour.
– v – Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST ..............................
HDP2100 Users Manual — vi — P ROJECTION D ISTANCE VS . P ROJECTION S IZE ................................................................................................................... 39 H DP2100 Series Proj ection Distance and Size Ta ble ..
HDP2100 Users Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and check that the following items are included: HDP2100 SERIES DLP P ROJECTOR R EMOTE CONTROL (WITH T.
HDP2100 Users Manual r Views of Projector Parts H DP2100 Series Front-right View I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Height-adjuster button Push to release height adjuster 2. Height adjuster Adjusts level of projector 13 3. Lens Projection Lens 4.
Top view—On-screen Display (OSD) buttons and LEDs I TEM L ABEL D ESCRIPTION S EE PAGE : 1. (Power button) Turns the projector On or Off. 11 2. BLANK Displays a blank screen and mutes audio 3. ◄ (Left cursor) / Volume- Navigates and changes settings i n the OSD Quick Menu – For Volum e 4.
HDP2100 Users Manual Rear view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. AC IN Connect the POW ER CABLE 11 2. (USB) Connect the USB CABLE from a computer 3. COMPONENT IN Connect a component video enabled device 4. S-VIDEO IN Connect the S-VIDEO CABLE from a video device 5.
HDP2100 Users Manual Bottom view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Tilt adjustor Rotate adjuster lev er to adjust angle p osition. 13 2. Ceiling support holes Contact your dealer for information on m ounting the projector on a ceiling 3. Height adjustor Adjuster drops down when adjuster button is pushed.
HDP2100 Users Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting tu rned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector.
– 7 – I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Power OFF Turns the projector off 11 2. HDMI 2 Displays the HDM I 2 source selection 3. S-VIDEO Displays the S-VIDEO source selection 4. VIDEO Displays the VIDEO source selection 5. Up cursor / Keystone+ Navigates and changes settings i n the OSD Quick Menu – For Keyst one 6.
– 8 – Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector.
— 9 — S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1.
Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 11 – Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector.
5. When the POWER OFF window ap- pears, press on the control panel or on the remote control. The projec- tor turns off. Caution: Do not unplug the power cord until the READY LE D stops flashing–indicati ng the projector has cooled down.
Adjusting the Projector Level Take note of the following w hen setting up the projector: • The projector table or st and should be level and sturdy . • Position the projector so that it is perpendicular to the screen. • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle.
– 14 – Adjusting the Zoom ring, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size B . 2. Use the Image-focus control (on the projector only) to sharpen the pro- jected image A .
– 15 – Adjusting the Volume 1. Press the Volume +/- buttons on the remote control. The volume control appears on the display. 2. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/- . 3. Press the MUTE button to turn off the volume (This feature is available only on the remote).
— 16 — O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control curs or buttons or the buttons on the top of the projector to navigate and make changes to the OSD.
– 17 – Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SYSTEM SETUP: Basic . 2. Press the cursor ▲▼ button until Language is highlighted.
HDP2100 Users Manual – 18 – OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting..
PICTURE: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Basic menu. Press ◄► to change values for settings.
PICTURE: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Advanced menu. Press ◄► to change values for settings.
HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. I TEM D ESCRIPTION Primary Color Press the ◄► buttons to set the Primary Color. Notes: There are six sets ( R / G/ B/ C/ M/ Y) of colors to be customized. Hue Press the ◄► buttons to adju st the Hue.
DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. I TEM D ESCRIPTION Aspect Ratio Press the cursor ◄► button to set th e Aspect Ratio.
PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected.
SYSTEM SETUP: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Basic menu. Press the cursor ▲▼ button to move up and down in the SYSTEM SETUP: Basic menu. Press ◄► to change values for settings.
Menu Settings Press the ENTER button to enter the Menu Settings sub menu. I TEM D ESCRIPTION Menu Position Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Display Ti me Press the ◄► buttons to set the Menu Display timer before the OSD times out.
SYSTEM SETUP: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Advanced menu. Press the cursor ▲▼ button to move up and down in the SYSTEM SETUP: Advanced menu. I TEM D ESCRIPTION Audio Press the ENTER bu tton to enter the Audio sub menu.
– 27 – Audio Press the ENTER button to enter the Audio sub menu. I TEM D ESCRIPTION Volume Press the ◄► butto ns to adju st the audi o Volum e. Bass Press the ◄► buttons t o adjust t he audio Ba ss. Treble Press the ◄► buttons t o adjust t he audio Tr eble.
HDMI Press the ENTER button to enter the HDMI sub menu. I TEM D ESCRIPTION HDMI Format Press the ◄► buttons to select from th ree HDMI display form ats: Auto/ PC signal/ Vi deo signal. HDMI Amplifier Gain Press the ◄► buttons to adju st HDMI Amplifier Gain.
INFORMATION Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the INFORMATION Menu . I TEM D ESCRIPTION Source Displays the activated input source. Resolution Displays the nati ve resolution of input source. Lamp Hour Displays the number of hours t he lamp has been in use.
— 30 — M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this produc t contains a small amount of mercury.
3. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.
– 32 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn.
Using the Kensington ® Lock If you are concerned about security, attach the proj ector to a permanent objec t with the Kensington slot and a security cable. Note: Contact your vendor for details on purchas ing a suitable Kensi ngton security cable. The security lock corresponds to Kensington’s Mi croSaver Security Syst em.
— 34 — T ROUBLE SHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose con- nection.
– 35 – LED Error Messages E RROR C ODE M ESSAGES P OWER LED B LINK R EADY LED B LINK T EMP LED B LINK Lamp Ready ON ON OFF Start ON OFF OFF Cooling ON FLASHING OFF Over temperature OFF OFF ON Ther.
– 36 – Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
– 37 – Audio Problems Problem: There is no sound 1. Adjust the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced.
— 38 — S PECIFICATIO NS Specifications Model H DP2100 Series Display type TI DLP DMD 0.65” Native Resolution 1920 x 1080 Weight 3.4 kg (7. 5 lbs) Projection distance 1 meters ~ 10 meters Projection screen size 25 " ~ 300" Projection lens Manual Focus/ Manual Zoom Zoom ratio 1.
– 39 – Projection Distance vs. Projection Si ze H DP2100 Series Projection Distance and Size Table 16:9 SCREEN PROJECTION DISTANCE DIAGONAL WIDTH HEIGHT INCH CM CM CM MIN LENGTH (WITH MAX ZOOM) AV.
– 40 – H DP2100 Series Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) NTSC — 15.
– 41 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.1 50.0 — O — O 1080p 67.5 60.
Projector Dimensions – 42 – HDP2100 Users Manual.
— 43 — R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial environment.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Knoll HDP2100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Knoll HDP2100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Knoll HDP2100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Knoll HDP2100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Knoll HDP2100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Knoll HDP2100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Knoll HDP2100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Knoll HDP2100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
