Manuel d'utilisation / d'entretien du produit 2217PWC du fabricant AOC
Aller à la page of 24
2217Pwc User Man ual 1. Preface About This Guide This guide describes the monitor's features, setup, and operation. lnformation in this document is subject to change w ithout notice. The sections are as follows: • Safety Instructions : lists safety information.
2. Safety Introduction FCC Notice FCC Class B Radio Frequency Interference Statement WA RNING : (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digit al device, purs uant to Part 15 of the FCC Rules.
Precautions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards. Read and follow these precautions when connecting and using your computer monitor: PRECAUTIONS • Do not use the monitor near water, e.
Adjusting Viewing Angle • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor's angle.
NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Attaching the Cables Cable Connections On Back of Monitor and Computer 1. Power 2. Audio 3. DVI 4. Analog 5. USB up 6. USB down x 3 Turn off your computer before performing the procedure below.
Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm.
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Foll ow thes e steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor.
1 Eco Mode / Up 2 Auto (Exit) / Left 3 Menu / Right 4 Volume 5 Power on/off 6 Camera 7 microphone Operation Steps 1) Press the MENU-button ( ) to activate the OSD window. 2) Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate sub-menu .
OSD Settings • Press the MENU-button to activate the OSD window. • Press+ or - to navigate through the function s. Once the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has a sub -menu, press or again to navigate through the sub-menu functions.
DCC: Dynamic color control ICM: Intelligent color management 1) How to use Color Boost? YCM adjustment: In addition to the basic R (red), G (green), B (blue) color adjustments, Col or Boost has added Y (yellow), C (cyanine), and M (magenta) for more color fine-tuning options.
Full Enhance: When "Full Enhance" is turned on, the color saturation of the entire screen is fully enriched, thus all colors become more vibrant . Nature Skin: When "Natural Skin" is turned on, the red and y ellow colors are enriched automatically, thus presents human skin with more natural and truer colors.
Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain landscape woul d look more natural and fresh.
Auto Detect: When “Auto Detect” is turned on, every pigment will be detec ted and self-adj uste d to render a lively picture. Demo: Screen divided into two for demonstration purposes. 2) How to use Picture Boost? Users can change the color settings of a self-selected zone on the screen.
Disclaimer: DCB aftereffects are subject to the resolution and quality of the display content, hence m ay look different than the above illustrations. DCR Adjustment What is DCR? Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen so users can see the darker areas of the display ed content in more depths.
DCR Demos: Disclaimer: DCR aftereffects are subject to the resolution and quali ty of the disp lay content, hence may look different than the above illu strations. Function Control Illustration Luminance Adjust Range Description Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register.
Internet Internet Mode Game Game Mode Movie Movie Mode Sports Sports Mode Gamma1 Adjust to Gamma1 Gamma2 Adjust to Gamma 2 Gamma Gamma3 Adjust to Gamma 3 Off Disable dynamic contrast ratio DCR On Enable dynamic contrast ratio Image Setup Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise.
OSD Setup H.Position 0-100 Adjust the verticalposition of OSD V.Position 0-100 Adjust the horizontal position of OSD Timeout 0-100 Adjust the OSD Timeout Language Select the OSD language Extra Digital.
9. Click on the 'Open' button, then click on the 'OK' button. 10. Select your monitor model and click on the 'Next' button. 11. Click on the 'Finish' button then the 'Close' button. If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
13. Click on the 'Finish' button then the 'Close' button. 14. Click on the 'OK' button and then the 'OK' button again to close the Display_ Properties dialog box. Windows Vista 1. Start Windows® Vista 2. Click the Start button; select and click on 'Control Panel'.
• The Computer Video Card should be snugly seated in its slot. • Make sure the monitor's video cable is properly connected to the computer. • Inspect the monitor's video cable and make sure none of the pins are bent.
Active < 49W Power Consumption Standby < 1W Speakers 2 x 1.5w Connector Type 1 5-pin Mini D-Sub & DVI-D Signal Cable Type Detachable Dimensions & Weight: Height (with base) 505.2 mm Width 442.3 mm Depth 280.1 mm Weight (monitor only) 5.58 kg Physical Characteristics Weight (with packaging) 7.
1280x1024 79.976 75 WS XGA 1680x1050 65.29 60 Pin Assignments Pin Number 15-Pi n Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Ground 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Detect Cable 11 N.C. 12 DDC-Serial data 13 H-sync 14 V-sync 15 DDC-Serial clock Pin No.
6 DDC Clock 14 +5V Power 22 TMDS Clock Shield 7 DDC Data 15 Ground(for+5V) 23 TMDS Clock + 8 N.C. 16 Hot Plug Detect 24 TMDS Clock - Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
AOC Internat ional (Europe) G mbH will pay th e return shipping charges within one of the count ries specif ied within this warranty s tatement. AOC Int ernational (Europe) GmbH is not responsible for any costs assoc iated with the transportat ion of product across internat ional borders.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté AOC 2217PWC c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du AOC 2217PWC - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation AOC 2217PWC, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le AOC 2217PWC va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le AOC 2217PWC, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du AOC 2217PWC.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le AOC 2217PWC. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei AOC 2217PWC ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
