Manuel d'utilisation / d'entretien du produit 415.165059 du fabricant Kenmore
Aller à la page of 28
Use and Care Guide ® Liquid Propane Gas Grill Kenmore Model No. 415.16505900 Kmart item No. 640-t 75289tt5 This Grill is for Outdoor Use Only • Read and follow all Safety, Assembly, and Use and Care instructions in this Guide before assembling and cooking with this grill.
if you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. 4. if odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. 1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
For Your Safety ...................................... 2 Grill Service Center ................................... 2 Product Record Information ............................ 2 Safety Symbols ...................................... 2 Installation Safety Precautions .
LP Tank • NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full. • If the information in two points above is not followed exactly, a fire causing death or serious injury may occur.
LP Tank Exchange •Many retailers that sell grills offer you the option of replacing your empty LP tank through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their cylinders.
Hold coupling nut and regulator as shown for proper connection to LP tank valve. Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP tank. 3.Completely open LP tank valve by turning OPD hand wheel counterclockwise.
zL zL For Safe Use Of Your Grill And To Avoid Serious Injury: *Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in bottom or back of grill. •Check burner flames regularly.
Main burner ignitor Lighting A Do not lean over grill while lighting. 1. Open lid during lighting. 2. Turn ON valve from source or tank. 3. Push and turn Ignition Burner control knob to _ HI and immediately press and hold Electronic Ignition button. 4.
Turning Grill Off •Turn all knobs to OFF position. Turn LP tank off by turning OPD hand wheel clockwise to a full stop. Ignitor Check •Turn gas off at LP tank. Press and hold ignitor button. "Click" should be heard and spark seen each time between collector box or burner and electrodes.
Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder. 2. Remove cooking grate and heat tent. 3. Under grill remove grease cup, disconnect ignitor wire from burner.
1 2 UPPER SUPPORT, F/ LEGS 80009811 2 1 LEG (WHEEL), LEFT, FRONT, 80009831 CURVED 3 1 LEG (WHEEL), LEFT, BACK, 80009830 STRAIGHT 4 1 SIDE BRACE F/TANK 80009815 RETAINER BRACKET 5 2 BRACKET, TANK SUPPO.
47 52 46 43 39 30,,,,_ _ 25,._ 36 15 14 38,,_ _,2 24 23 31 11 12 °464722309 °464722509 .
f g Left Leg i Place one upperleg as shown. NOTE: Left front and left back legs do not have leg extenders. In front, attach upperleg, side brace and left front leg (curve) with #10-24x1-1/4" screw and #10-24flange nut.
Upper and lower Front Panel and Top brace j Lay front legs down on the floor. Fit upper front panel between legs. Attach with 2" hinge pins and hitch pins. iAttach lower front panel with #10-24x2" machine screws and #10-24 flange nuts. Attach top brace with #10-24x2" machine screws and #10-24 flange nuts.
Tank Exclusion Hank tank exclusion wires onto lower front panel brackets, attach other ends to back brace with #8-32X3/8" sheet metal screws. #8-32X3/8" Sheet Metal Screw Qty.2 BackBrace Wheels Turn assembly upside down. i_ Insert axle rod through wheel, legs and other wheel.
Control Panel and Firebox Support _] Stand cart upright. In front, fit control panel between left and right legs. Insert #10-24x2" machine screws to hold panel in place. Place upper firebox supports onto screws making sure angle side is facing the front and attach with # 10-24 flange nuts.
Heat Shield Attach heat shield with #10-24xl/2" machine screws and #10-24 flange nuts. Tank Retainer Insert tank retainer into side brace and secure with #10-24x3/8" wing screw. #10-24xl/2" Machine Screw Qty.2 #10-24 Flange Nut Qty. 2 eat shield #10-24x3/8" Wing Screw Qty.
Burner and Firebox and Control Knobs Place burner assembly into firebox. Fasten the burner assembly to the firebox using 5x15 fiber washers and #10-24xl/2" machine screws (A).
Right Side Shelf and Side Burner Support Shelf I ] Attach mounting brackets to Right Side Shelf with #8-32x3/8" sheet metal screws and side shelf bushings (A). Note: Do not overtighten the screws. Insert mounting brackets into Side Burner Shelf Support, and secure with #10-24x1/2" machine screws (B).
Sideburner [ Attach sideburner valve with #8-32x3/8" machine screws. Attach sideburner pan with #8-32x3/8" sheet metal screws and 5x9 fiber washers (A). Place sideburner into shelf (B). Make sure valve is inside sidebumer tube (C). Attach sideburner with #8-32 wing nut and 5x9 fiber washer (B).
Lower Hinges [ Attach lower hinges to back of firebox using #10-24xl/2" machine screws, 5x15 fiber washers and #10-24 flange nuts. The center flat portion of the hinge should be at the bottom (see inset). #10-24xl/2" Machine Screw Qty.4 Center flat portion of hinge on bottom 5x15 Fiber Washer Qty.
Attach Lid Place lid assembly onto firebox, aligning hinges. Hinges on lid fit inside hinges on firebox. Secure using two hinge pins and hitch pins. Hinge Pin Qty.2 Hitch Pin Qty.2 Heat Diffuser and Cooking Grate [ Place heat diffuser onto heat diffuser support.
Swing Away Insert ends of Swing Away pivot wire into holes in sides of grill lid. Insert ends of Swing Away leg wire into holes in sides of firebox. NOTE: Pivot and leg wires, running side-to-side, should be under wires running front-to-back. If pivot and leg wires are on top, Swing Away is installed upside-down.
LP Tank Tank collar opening must face to front of grill. Loosen wing nut from tank retainer bracket. Set bottom of tank into notches of tank bracket. Place tank retainer bracket onto tank collar and tighten wing nut.
EMERGENCIES; if a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection.
Troubleshooting (continued) ELECTRONIC IGNITION: • No spark, no ignition noise. • No spark, some ignition noise. • Sparks, but not at electrode or at full strength. Burner(s) will not light using ignitor. (See Electronic Ignition Troubleshooting also) Burner(s) will not match light.
Troubleshooting - Electronic Ignition ,Battery not installed properly. SECTION I No sparks appear at any electrodes when controlknob turned to _" ; no noise can be heardfrom spark module. SECTION II No sparks appear at any electrodes when controlknob turned to ; noise can be heardfrom spark •Check battery orientation.
iiiiiiiiiiiiiiiiiiiiiiiiii_ _¸¸ iiiiiiiiiiiiiiiiiiiiii_ '_ iiiiiiiiiiiiiiiiiiiii_ _ iiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiii.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Kenmore 415.165059 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Kenmore 415.165059 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Kenmore 415.165059, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Kenmore 415.165059 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Kenmore 415.165059, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Kenmore 415.165059.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Kenmore 415.165059. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Kenmore 415.165059 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
