Manuel d'utilisation / d'entretien du produit RX-E100SL du fabricant JVC
Aller à la page of 42
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
Warnings, Cautions and Others CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
1 T able of Contents Getting Star ted ........................................... 2 Before Installation ...................................................................... 2 Checking the Supplied Accessories ........................................
2 Getting Star ted Putting Batteries in the Remote Control Before using the remote control, put two supplied batteries f irst. • When using the remote control, aim the remote control directly at the remote sensor on the recei ver . 1. On the back of the remote contr ol, remo ve the battery cov er .
3 Connecting the FM and AM Antennas FM Antenna (supplied) If FM reception is poor, connect outdoor FM antenna (not supplied). AM antenna connection Connect the AM loop antenna supplied to the AM LOOP terminals. T urn the loop until you have the best r eception.
4 SUBWOOFER OUT INPUT HIGH IMPEDANCE Powered subwoofer (example) Getting Star ted 1 2 3 Speaker Layout Diagram Connecting the Speakers After connecting the front, center , rear speakers and/or a subwoofer , set the speaker setting information properly to obtain the best possible DSP effect.
5 Getting Started Left rear speaker F M 75 C O A X IA L CAUTION : SPEAKER IMPEDANCE 8 1 6 + – + – + – + – AM LOOP AM EXT A N T E N N A A U D I O R I G H T L E F T OUT (REC) IN (PLAY) V CR CD T.
6 FM 75 COAXIAL CAUTION : SPEAKER IMPEDANCE 8 1 6 + – + – + – + – AM LOOP AM EXT ANTENNA AUDIO RIGHT LEFT OUT (REC) IN (PLAY) VCR CD TV DVD DIGITAL 2 ( T V ) DIGITAL 1 ( D V D ) DIGITAL IN CEN.
7 TV DVD VCR CD DVD TV OUT IN LEFT RIGHT AUDIO LEFT RIGHT LINE OUT LEFT RIGHT FRONT/MIX AUDIO OUT LEFT RIGHT AUDIO OUT COAXIAL DIGIT AL OUT A B C OPTICAL DIGIT AL OUT Illustrations of the input/output terminals below ar e typical examples.
8 Basic Operations 1 T urn On the Power Press PO WER (or A UDIO of the POWER b uttons on the remote control). The ST ANDBY lamp g oes of f. The name of the current source (or station frequency) appears on the display . T o tur n off the power (into standby) Press PO WER (or A UDIO) again.
9 Basic Operations Basic adjustment auto memory This recei ver memorizes sound settings for each source .... • when you turn on the po wer , • when you change the source, and • when you change the analog/digital input mode (see page 11).
10 Basic Settings DVD TV VCR CD FM AM RX-E100 HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUST SETTING STANDBY DIGITAL DIGITAL SURROUND INPUT ANALOG/DIGITAL INPUT ATT MASTER VOLUME SURROUND O.
11 Basic Settings SUBWFR LFE MUTI N MH Z KH Z VOL DGTL AUT O LC R LS RS DOLBY D If the f ollowing symptoms occur while playing Dolby Digital or DTS Digital Surround softwar e with “DGTL A UTO” selected, f ollow the procedur e below . • Sound does not come out at the be ginning of playback.
12 ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS Basic Settings DVD TV V.
13 Basic Settings FR SP (Front Speaker) : T o register the front speaker size. CTR SP (Center Speaker) : T o r egister the center speak er siz e. REAR SP (Rear Speaker) : T o r egister the rear speaker size. * “LRG (large)” is the initial setting for the front speakers, and “SML (small)” is for the center and rear speakers.
14 Basic Settings DVD TV VCR CD FM AM RX-E100 HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUST SETTING STANDBY DIGITAL DIGITAL SURROUND INPUT ANALOG/DIGITAL INPUT ATT MASTER VOLUME SURROUND O.
15 Basic Settings C VOL O CONTROL Dynamic Range Compression — D.R.C. Y ou can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night. • This function tak es effect only when playing back a source using Dolby Digital.
16 Basic Settings DVD TV VCR CD FM AM RX-E100 HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUST SETTING STANDBY DIGITAL DIGITAL SURROUND INPUT ANALOG/DIGITAL INPUT ATT MASTER VOLUME SURROUND O.
17 ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS Sound Adjustments Y ou can also use the remote contr ol for some sound adjustments. • When using the remote control, see also “Mastering Remote Operations” on page 32.
18 Sound Adjustments DVD TV VCR CD FM AM RX-E100 HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUST SETTING STANDBY DIGITAL DIGITAL SURROUND INPUT ANALOG/DIGITAL INPUT ATT MASTER VOLUME SURROUN.
19 ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS Adjusting the T one Y ou can adjust the bass and treble sounds as you like. • Y ou have to mak e these adjustments for each sour ce. Bef ore you start, r emember .
20 T uner Operations Y ou can also use the remote contr ol for some tuner operations. • When using the remote control, see also “Mastering Remote Operations” on page 32.
21 T uner Operations Selecting the FM Reception Mode When an FM stereo broadcast is hard to recei ve or noisy , y ou can change the FM reception mode while recei ving an FM broadcast. • Y ou can store the FM reception mode for each preset station. Bef ore you start, r emember .
22 Cr eating Realistic Sound Fields Y ou can use the following DSP (Digital Signal Processor) modes to reproduce a realistic sound field. • Surround modes • D AP modes ■ Surr ound modes Surround modes cannot be used when only the fr ont speakers are connected to this r eceiver (without the rear speak ers or center speaker).
23 Creating Realistic Sound Fields These D AP modes can be used to add the acoustic surround effects while reproducing stereo analog software or Linear PCM digital software, and can gi ve you a real “being there” feeling.
24 Cr eating Realistic Sound Fields About Relations between Speaker Layout and DSP Modes A vailable DSP modes will v ary depending on how many speakers are used with this recei ver . Make sure that y ou hav e set the speaker information corr ectly (see page 12).
25 Creating Realistic Sound Fields It will be con venient for y ou to use the remote contr ol for DSP oper ations, since you can adjust them fr om your listening point, and use the test signal. • W hen using the buttons on the front panel, see pages 29 to 31.
26 Cr eating Realistic Sound Fields 4 Press TEST to c heck the speaker output balance. “TEST L” starts flashing on the display , and a test tone comes out of the speakers in the follo wing order: Notes: • Y ou can adjust the speaker output lev els without outputting the test tone.
27 6 Press TEST a gain to stop the test tone. 7 Press EFFECT to select the DSP eff ect level (1 to 5) y ou want. • As the number increases, the DSP ef fect becomes stronger (normally set it to “EFFECT 3”). T o cancel Theater Sur round Press DSP MODE repeatedly until “STEREO” appears on the display .
28 ANALOG PRO LOGIC SUBWFR VOL DSP LR LS S RS ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS Cr eating Realistic Sound Fields Using DAP Modes (Remote Control) A DAP mode cannot be used with another DSP mode . Once one of the D AP modes is activ ated, the other DSP mode in use will be canceled.
29 ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS DVD TV VCR CD FM AM RX-E100 HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUST SETTING STANDBY DIGITAL .
30 Cr eating Realistic Sound Fields Using Theater Surr ound (Fr ont Panel) Theater Surround cannot be used with another DSP mode. Once Theater Surround is activ ated, the other DSP mode in use will be canceled. When using the b uttons on the front panel, no test tone is av aila ble.
31 ANALOG PRO LOGIC SUBWFR LFE VOL DGTL AUT O INPUT ATT DSP LC R LS S RS LPCM DOLBY D DTS 3 Press ADJUST . The CONTR OL buttons no w work for sound adjustments. 4 Press CONTR OL ∞ (or 5 ) r epeatedly until one of the follo wing indications (with the current setting) * appears.
32 Mastering Remote Operations Y ou can use the remote contr ol to operate not only this receiv er but also other JVC products. • Refer also to the manuals supplied for the other products. – This remote control can operate a VCR whose remote control code is set to A code.
33 Mastering Remote Operations ❏ Operating other JVC products — Audio/video operation buttons ■ After pressing DV D (source selecting button), you can use the following b uttons for D VD operations. 3 : Start playback. 7 : Stop playback. 8 : Pause playback.
34 Par ts Identification Remote Contr ol DVD TV VCR CD FM AM RX-E100 HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUST SETTING STANDBY DIGITAL DIGITAL SURROUND INPUT ANALOG/DIGITAL INPUT ATT M.
35 Parts Identification/T roubleshooting T r oubleshooting Use this chart to help you solve daily operational problems. If there is an y problem you cannot solve, contact your JVC service center . PROBLEM The power does not comes on. No sound from speakers.
36 Specifications Amplifier Output Po w er At Stereo operation: Front channels: 70 W per channel, min. RMS, driven into 8 Ω , 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion. At Surround operation: Front channels: 70 W per channel, min.
37 Memorandum Specifications/Memorandum Note the adjustments y ou have made f or each source below f or your futur e reference. The following adjustments can be stor ed for each source: • Analog/dig.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous.
LIMITED W ARRANTY A UDIO-2 JVC COMP ANY OF AMERICA warrants this product and all parts thereof, e xcept as set forth below ONL Y T O THE ORIGINAL PURCHASER A T RET AIL to be FREE FROM DEFECTIVE MA TERIAL AND WORKMANSHIP from the date of original retail purchase f or the period as shown below .
VICTOR COMP ANY OF JAP AN , LIMITED EN 0301NHMMDWJEIN J V C RX-E100SL[J]_COVER_f 01.3.7, 2:43 PM 2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté JVC RX-E100SL c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du JVC RX-E100SL - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation JVC RX-E100SL, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le JVC RX-E100SL va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le JVC RX-E100SL, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du JVC RX-E100SL.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le JVC RX-E100SL. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei JVC RX-E100SL ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
