Manuel d'utilisation / d'entretien du produit MX-KB30 du fabricant JVC
Aller à la page of 62
For Customer Use: Enter below the Model No . and Serial No. which are located either on the rear , bot- tom or side of the cabinet. Retai n this in fo r m a ti o n fo r f u t ur e r e fer e nc e .
G-1 Warnings, Cautions and Others For U.S.A. This equipment has been tested a nd found to comply with th e limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are design ed to provide reas onable prot ection against harmful interference in a residential instal- lation.
G-2 CLASS 1 LASER PRODUCT DANGER 1. Invisible laser radiation when open and interl ock failed or defeated. Avoid direct e xposure to beam. CAUTION 1. Do not open the top cove r. There are no user serviceable parts inside the unit; leave all servi cing to qualified service p ersonnel.
1 Introduction Thank you for purchasing the JVC Co mpact Component System. We hope it will be a valued addition to your home, giving yo u years of enjoyment. Be sure to read this instruction manual carefully before operating your new stereo system. In it you will find all the information you need to set up and use the system.
2 Table of Contents Introduction ................................................... ................................................................ 1 Features......................... ................ ................. .................... .........
3 Getting Started Accessories Make sure that you have all of the following items, which are supplied with the System. AM Loop Antenna (1) FM Wire Antenna (1) Remote Control (1) Batteries (2) If any of these items are missing, contact your dealer immediately.
4 Getting Started CAUTION: • Make all connec tions before plugging the Sys tem into an AC power outlet. Connecting the FM Antenna Using the Supplied Wire Antenna Using an FM 75-Ohm Antenna Cable (not Supplied) If reception is poor, connect the outside antenna.
5 Getting Started Connecting the AM Antenna Rear Panel of the Unit • Even when connecting an outside AM antenna, keep the indoor AM loop connected. CAUTION: • To avoid noise, keep ante nnas away from the System, the con necting cord and the AC power cord.
6 Getting Started Connecting External Equipment Connect a signal cord (not supplied) between the System ’ s AUX-IN terminals and the output terminals of the external MD recorder, tape deck, etc. You can then listen to the external source through the System.
7 Basic Operations ) Turning the Power On and Off Turning the System On 1 Pre ss th e STANDBY/ ON but t on . The display comes on and “ WELCOME ” is displayed once. The STANDBY indicator goes out. The System comes on ready to continue in the mode it was in when the power was last turned off.
8 Basic Operations Fade-out Muting (FADE MUTING) You can mute the output with one touch operation. To muting the output , press the FADE MUTING button on the Remote Control. The output is faded out. To release muti ng , press the FADE MUTING button once again.
9 Using the Tuner You can listen to FM and AM stations. Stations can be tuned in manually, automatically, or from preset memory storage. ❏ Before listening to the radio: • Make sure that both the FM and AM antennas are correctly connected. (See pages 4 and 5).
10 Using the Tune r • In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best receptio n. Presetting Stations You can preset up to 30 FM stations and up to 15 AM stations. • Preset numbers may have been set to factory test fre- quencies prior to shipme nt.
11 Using the CD Player The CD Player h as the rotational disc tra y that can accommodate 3 CDs. You can use Normal, Program, Random, or Repeat Play. Here are the basic things you need to know to play CDs and locate the different tracks on them.
12 Using the CD Player Example of indication: One Touch Play The power comes on, and operations are done automatically. ❏ By pressing the CD 6 button, the System will come on, and if a CD is loaded for the di sc number that was last ly selected, it will start playing from the first track.
13 Using the CD Player Basics of Using the CD Player- Normal Play To Play CDs 1 Load CDs. 2 Pre ss one o f t he Di sc but t on ( CD1 - CD3) you want to pl ay. The selected disc number (e.g. “ CD DISC 1 ” ) appears on the display. The first track of t he selected CD begi ns playing.
14 Using the CD Player Programming the Playing Order of the Tracks You can program the playing order of the tracks on all the CDs. Note that you can only make a program when the CD Player is stopped. ❏ You can program up to 32 tracks in any desired order including the same trac ks.
15 Using the CD Player Random Play The tracks of all the CDs will play in no special order when you use this mode. • To use Repeat Play for Random Play, press the REPEAT but- ton to select “ REPEAT ALL ” or “ REPEAT 1 ” before starting playback.
16 Using the Cassette Deck (Listening to a Tape) The Cassette Deck allows you to play, record, and dub audio tapes. ❏ Listening to type I tape is suitable for this Cassette Deck.
17 Using the Cassette Deck (Recording) Recording onto a cassette from any of the sound sources is simple. Just place a tape in Deck B, have the source ready, make one or two settings, and you ’ re ready to r ecord. For each source, t he pro- cedure is a little bit different so we explain each separately.
18 Using the Cassette Deck (Recording) Standard Recording This is the basic method for recording any source. The System also has special ways for recording CD to tape, and ta pe to tape, which save you time and effort, as well as give you some special effects.
19 Using an External Equipment Listening to the External Equipment You can listen to the external equipment such as MD recorder, cas- sette deck, or other auxiliary. ❏ First, make sure that the external equipment is properly connect- ed to the Syst em.
20 Using the Timers The timers lets you control recording and listening functions auto- matically . Three types of timers are available : DAILY Timer Use this timer to set wake up every day to music from any source, instead of an alarm cloc k. REC (Recording) Timer Unattended recording of radio broadcasts.
21 Using the Timers Setting the Daily Timer Once you have set the Daily Timer, the timer will be activated at the same time every day. The Timer indicator ( ) and “ DAILY ” indicator on the display shows that the Daily Timer you have set is in effect.
22 Using the Timers Preparation for each music source: Perform the following operation according to the music source you have selected. Then, the System enters Volume Setting mode. When selecting TUNER FM or TUNER AM: Press the ¢ or 4 button to sele ct the preset station number, then press the SET button.
23 Using the Timers Using the Unit You can set the time in the same way as for setting the Daily Tim- er. 1 Inser t a blank or eras able t ape i nto t he Deck B an d w ind pa st the tape leader. 2 Press t he CLOCK / TIMER button unt il “ ON TIME ” i mm edi atel y af ter “ REC ” appears on the di spl ay.
24 Using the Timers Setting the SLEEP Timer Use the Sleep Timer to turn the System off after a c ertain number of minutes when it is playing. By setting the Sleep Timer, you can fall asleep to music and know that your System will turn off by it- self rather than play all night.
25 Care And Maintenance Handle your CDs and tapes carefully, and they will last a long time. Compact Discs CAUTION: • Do not use any solvent (for example, conven- tional record cleaner, s pray thinner, benzine, etc.) to clean a CD. General Notes In general, you will have the best performance by keeping your CDs and the mechanism clea n.
26 Troubleshooting • If you are having a problem with your System, check this list for a possible solution before calling for service. • If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a q ualified person, such as your dealer, for service.
27 BT -51001-5 (0301) QUALITY SER VICE HOW TO LOCA TE YOUR JVC SERVICE CENTER Dear Customer , In order to receive the most satisfaction from your purchase,please read the instruction booklet before operating the unit.
28 THIS LIMITED W ARRANTY IS V ALID ONL Y IN THE FIFTY (50) UNITED ST A TES, THE DISTRICT OF COLUMBIA AND IN COMMONWEAL TH OF PUERTO RICO. WHA T WE WILL DO: If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner .
1203HMMCREBET © 2003 VICT OR COMP ANY OF JAP A N, LIMITED EN VICTOR COMPANY OF JAPAN, LIMITED Specifications Amplifier Output Power 150 W per channel, min.
For Customer Use: Enter below the Model No . and Serial No. which are located either on the rear , bot- tom or side of the cabinet. Retai n this in fo r m a ti o n fo r f u t ur e r e fer e nc e .
G-1 W arnings, Cautions and Others / Mises en gar de, précautions et indications diverses (For U .S.A ) Caution - PO WER switc h! Disconnect the mains plug to shut the power off com pletely . The POWER s witch in any position does not disconnect the mains line.
G-2 IMPORT ANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CA UTION: Do not open th e top cov er . There are no user ser viceable par ts inside the Unit; leav e all ser vicing to qual - ified ser vice personnel. 3. CA UTION: Visible and in visible laser radiation when open and inter lock f ailed or defeated.
1 English Introduction Thank you for purchasing the JVC Co mpact Component System. We hope it will be a valued addition to your home, giving yo u years of enjoyment. Be sure to read this instruction manual carefully before operating your new stereo system.
2 English Table of Contents Introduction ................................................... ................................................................ 1 Features......................... ................ ................. .................... .
3 English Getting Started Accessories Make sure that you have all of the following items, which are supplied with the System. AM Loop Antenna (1) FM Wire Antenna (1) Remote Control (1) Batteries (2) If any of these items are missing, contact your dealer immediately.
4 Getting Started English CAUTION: • Make all connec tions before plugging the Sys tem into an AC power outlet. Connecting the FM Antenna Using the Supplied Wire Antenna Using an FM 75-Ohm Antenna Cable (not Supplied) If reception is poor, connect the outside antenna.
5 Getting Started English Connecting the AM Antenna Rear Panel of the Unit • Even when connecting an outside AM antenna, keep the indoor AM loop connected. CAUTION: • To avoid noise, keep ante nnas away from the System, the con necting cord and the AC power cord.
6 Getting Started English Connecting External Equipment Connect a signal cord (not supplied) between the System ’ s AUX-IN terminals and the output terminals of the external MD recorder, tape deck, etc. You can then listen to the external source through the System.
7 English Basic Operations ) Turning the Power On and Off Turning the System On 1 Pre ss th e STANDBY/ ON but t on . The display comes on and “ WELCOME ” is displayed once. The STANDBY indicator goes out. The System comes on ready to continue in the mode it was in when the power was last turned off.
8 Basic Operations English Fade-out Muting (FADE MUTING) You can mute the output with one touch operation. To muting the output , press the FADE MUTING button on the Remote Control. The output is faded out. To release muti ng , press the FADE MUTING button once again.
9 English Using the Tuner You can listen to FM and AM stations. Stations can be tuned in manually, automatically, or from preset memory storage. ❏ Before listening to the radio: • Make sure that both the FM and AM antennas are correctly connected.
10 Using the Tune r English • In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best receptio n. Presetting Stations You can preset up to 30 FM stations and up to 15 AM stations. • Preset numbers may have been set to factory test fre- quencies prior to shipme nt.
11 English Using the CD Player The CD Player h as the rotational disc tra y that can accommodate 3 CDs. You can use Normal, Program, Random, or Repeat Play. Here are the basic things you need to know to play CDs and locate the different tracks on them.
12 Using the CD Player English Example of indication: One Touch Play The power comes on, and operations are done automatically. ❏ By pressing the CD 6 button, the System will come on, and if a CD is loaded for the di sc number that was last ly selected, it will start playing from the first track.
13 Using the CD Player English Basics of Using the CD Player- Normal Play To Play CDs 1 Load CDs. 2 Pre ss one o f t he Di sc but t on ( CD1 - CD3) you want to pl ay. The selected disc number (e.g. “ CD DISC 1 ” ) appears on the display. The first track of t he selected CD begi ns playing.
14 Using the CD Player English Programming the Playing Order of the Tracks You can program the playing order of the tracks on all the CDs. Note that you can only make a program when the CD Player is stopped. ❏ You can program up to 32 tracks in any desired order including the same trac ks.
15 Using the CD Player English Random Play The tracks of all the CDs will play in no special order when you use this mode. • To use Repeat Play for Random Play, press the REPEAT but- ton to select “ REPEAT ALL ” or “ REPEAT 1 ” before starting playback.
16 English Using the Cassette Deck (Listening to a Tape) The Cassette Deck allows you to play, record, and dub audio tapes. ❏ Listening to type I tape is suitable for this Cassette Deck.
17 English Using the Cassette Deck (Recording) Recording onto a cassette from any of the sound sources is simple. Just place a tape in Deck B, have the source ready, make one or two settings, and you ’ re ready to r ecord. For each source, t he pro- cedure is a little bit different so we explain each separately.
18 Using the Cassette Deck (Recording) English Standard Recording This is the basic method for recording any source. The System also has special ways for recording CD to tape, and ta pe to tape, which save you time and effort, as well as give you some special effects.
19 English Using an External Equipment Listening to the External Equipment You can listen to the external equipment such as MD recorder, cas- sette deck, or other auxiliary. ❏ First, make sure that the external equipment is properly connect- ed to the Syst em.
20 English Using the Timers The timers lets you control recording and listening functions auto- matically . Three types of timers are available : DAILY Timer Use this timer to set wake up every day to music from any source, instead of an alarm cloc k.
21 Using the Timers English Setting the Daily Timer Once you have set the Daily Timer, the timer will be activated at the same time every day. The Timer indicator ( ) and “ DAILY ” indicator on the display shows that the Daily Timer you have set is in effect.
22 Using the Timers English Preparation for each music source: Perform the following operation according to the music source you have selected. Then, the System enters Volume Setting mode. When selecting TUNER FM or TUNER AM: Press the ¢ or 4 button to sele ct the preset station number, then press the SET button.
23 Using the Timers English Using the Unit You can set the time in the same way as for setting the Daily Tim- er. 1 Inser t a blank or eras able t ape i nto t he Deck B an d w ind pa st the tape leader. 2 Press t he CLOCK / TIMER button unt il “ ON TIME ” i mm edi atel y af ter “ REC ” appears on the di spl ay.
24 Using the Timers English Setting the SLEEP Timer Use the Sleep Timer to turn the System off after a c ertain number of minutes when it is playing. By setting the Sleep Timer, you can fall asleep to music and know that your System will turn off by it- self rather than play all night.
25 English Care And Maintenance Handle your CDs and tapes carefully, and they will last a long time. Compact Discs CAUTION: • Do not use any solvent (for example, conven- tional record cleaner, s pray thinner, benzine, etc.) to clean a CD. General Notes In general, you will have the best performance by keeping your CDs and the mechanism clea n.
26 English Troubleshooting • If you are having a problem with your System, check this list for a possible solution before calling for service. • If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a q ualified person, such as your dealer, for service.
1203HMMCREBET EN, FR © 2003 VICT OR COMP ANY OF JAP AN, LIMITED MX-KB30(C)_all.book Pag e 1 Thursday, December 4, 2003 5:24 PM.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté JVC MX-KB30 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du JVC MX-KB30 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation JVC MX-KB30, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le JVC MX-KB30 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le JVC MX-KB30, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du JVC MX-KB30.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le JVC MX-KB30. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei JVC MX-KB30 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
