Manuel d'utilisation / d'entretien du produit MX-J700 du fabricant JVC
Aller à la page of 90
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
– G-1 – W arnings, Cautions and Others Mises en gar de , précautions et indications diverses CA UTION T o reduce the risk of electrical shocks, fire , etc.: 1. Do not remov e screws, co vers or cabinet. 2. Do not expose this appliance to r ain or moisture.
– G-2 – For Canada/pour le Canada CA UTION: TO PREVENT ELECTRIC SHOCK, MA TCH WIDE BLADE OF PLUG TO WIDE SLOT , FULL Y INSERT . A TTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE D ANS LA BORNE CORRESPOND ANTE DE LA PRISE ET POUSSER JUSQU A U FOND .
– 1 – English Introduction About This Manual This manual is org anized as follows: • The manual mainly explains operations using the b uttons and controls on the unit. Y ou can also use the b uttons on the remote control if they ha ve the same or similar names (or marks) as those on the unit.
– 2 – English Contents Location of the Buttons and Controls ....................... 3 Front Panel ................................................................. 3 Remote Control .......................................................... 5 Getting Started .
– 3 – English 1 2 3 6 7 8 9 p q w r t u i 5 4 MX-J700 o j l k e / z x c y v b ; a s d f g MX-J506/MX-J500 h Location of the Buttons and Controls Become familiar with the b uttons and controls on your unit. Front Panel Powered Rolling Panel Press P ANEL OPEN/ CLOSE to open the panel.
– 4 – English See pages in the parentheses for details. Front Panel 1 Disc trays 2 PO WER button and ST ANDBY lamp (9) 3 Display windo w 4 For MX-J700: SUBW OOFER V OLUME control (10) For MX-J506/MX-J500: A CTIVE BASS EX.
– 5 – English When using the remote control, point it at the remote sensor on the front panel. Remote Control Remote Control 1 Disc number buttons (CD1, CD2, and CD3) (13) Pr essing one of these buttons also turns on the unit.
– 6 – English Getting Started Unpacking After unpacking, check to be sure that you ha ve all the follo wing items. The number in the parentheses indicates the quantity of the pieces supplied. • AM loop antenna (1) • FM antenna (1) • Remote control (1) • Batteries (2) If any is missing, consult your dealer immediately .
– 7 – English 1 Connect the AM loop antenna to the AM LOOP terminals as illustrated. 2 T urn the AM loop antenna until y ou hav e the best r ece ption. T o connect an outdoor AM antenna When reception is poor , connect a single vinyl-covered wir e to the AM EXT terminal and extend it horizontally .
– 8 – English For pla ying the other equipment through this unit, connect between the audio output jacks on the other equipment and A UX jacks by using audio cords (not supplied). T o audio output T o start the display demonstration manually Press and hold DEMO f or more than 2 seconds.
– 9 – English Common Operations T urning On or Off the Power T o tur n on the unit, press POWER so tha t the ST ANDBY lamp goes off. The Po wered Rolling Panel opens automatically . T o tur n off the unit (on standby), press PO WER again so that the ST ANDBY lamp lights up.
– 10 – English When using the remote control, press SUBWOOFER + to increase the subwoofer v olume or press SUBWOOFER – to decrease it. For MX-J506/MX-J500 The ACTIVE B ASS EX. (e xtension) LEVEL control provided for this unit can maintain the richness and fullness of the bass sound while listening to any source at lo w volume.
– 11 – English Surround modes * : D.CLUB : Increases resonance and bass. HALL : Adds depth and brilliance to the sound. ST ADIUM : Adds clarity and spreads the sound, like in an outdoor stadium. SEA (Sound Effect Amplifier) modes: R OCK : Boosts lo w and high frequency .
– 12 – English Listening to FM and AM Broadcasts T uning in a Station 1 Pr ess FM/AM. The unit automatically turns on and tunes in the previously tuned sta tion (either FM or AM). The P owered Rolling Panel automatically opens. • Each time you press the button, the band alternates between FM and AM.
– 13 – English Playing Back CDs Loading CDs On the unit ONL Y : 1 Pr ess 0 f or the disc tray (CD1 to 3) y ou want to load a CD onto. The unit automatically turns on and the disc tray comes out. T he Powered Rolling Panel also opens automatically .
– 14 – English T o locate a particular point in a track During play , press and hold 1 or ¡ . • 1 : Fast re verses the disc. • ¡ : Fast forw ards the disc. When using the remote control, press and hold 1 / 4 or ¢ / ¡ . T o go to another track Press 4 or ¢ repeatedly before or during playback.
– 15 – English T o stop during play , press 7 . • Random play also stops when one of the disc trays is opened. T o exit fr om Random play mode, press PROGRAM/ RANDOM repeatedly again before or after play so that the unit enters another play mode.
– 16 – English Playing Back T apes Y ou can play back type I, type II, and type IV tapes without changing any settings. Playing Back a T ape 1 Pr ess EJECT ( 0 ) for the deck y ou want to use. 2 Put a cassette in, with the exposed part of the tape down.
– 17 – English Recording Recording a T ape on Deck B 1 Press EJECT 0 f or the deck B. 2 Put in a recordab le cassette, with the exposed part of the tape down. 3 Close the cassette holder gently . 4 Check the tape direction of deck B. • If the tape direction is not correct, press T APE 2 3 twice then 7 to change the tape direction.
– 18 – English CD Direct Recording Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you hav e made for Program play . 1 Put a recordable cassette into deck B. 2 Place a disc correctl y on the circle of the disc tray , with its label side up.
– 19 – English Auto Edit Recording By using Auto Edit Recording, you can record the CD tracks to f it the tape. Auto Edit Recording makes a program by selecting the CD tracks in numerical order .
– 20 – English Using the T imers There are three timers av ailable — Recording T imer, Daily T imer , and Sleep T imer . Before using the timers, you need to set the clock built in the unit. (See page 9.) Using Daily Timer W ith Daily T imer , you can wake to your fa vorite music or radio program.
– 21 – English DAILY Canceled ON TIME ON TIME Clock setting (See page 9.) REC 6 When selecting “– CD – –” 1) Press 4 or ¢ to select the disc number , then press SET . 2) Press 4 or ¢ to set the track number , then press SET . The unit enters volume setting mode.
– 22 – English Recording Timer 7:00 6:30 Sleep Timer 7:30 does not work. Recording Timer AM 6:00 7:30 7:00 6:30 Daily Timer AM 6:00 Using Sleep T imer W ith Sleep T imer , you can fall asleep to music. Y ou can set Sleep T imer when the unit is turned on.
– 23 – English Maintenance T o get the best performance of the unit, keep your discs, tapes, and mechanism clean. Handling cassette tapes • If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating.
– 24 – English Specifications MX-J700 Amplifier section — CA-MXJ700 Output P ower SUBWOOFERS: 100 W per channel, min. RMS, dri ven into 6 Ω at 63 Hz with no more than 10% total harmonic distortion. MAIN SPEAKERS:50 W per channel, min. RMS, driv en into 6 Ω at 1 kHz with no more than 10% total harmonic distortion.
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. GVT0029-001A [J] INSTRUCTIONS MX-J700 — Consists of CA-MXJ700 and SP-MXJ700.
– G-1 – W arnings, Cautions and Others CAUTION T o reduce the risk of electrical shocks , fire, etc.: 1. Do not remove scre ws, cov ers or cabinet. 2. Do not expose this appliance to r ain or moisture. 1. CLASS 1 LASER PRODUCT 2. D ANGER : Invisible laser r adiation when open and interlock f ailed or defeated.
– G-2 – GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC — NA TIONAL ELECTRICAL CODE POWER SER VICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. P ART H) GROUND CLAMPS GROUNDING CONDUCTORS (NEC SECTION 8.
– 1 – Introduction About This Manual This manual is org anized as follows: • The manual mainly explains operations using the b uttons and controls on the unit. Y ou can also use the b uttons on the remote control if they ha ve the same or similar names (or marks) as those on the unit.
– 2 – Contents Location of the Buttons and Controls ....................... 3 Front Panel ................................................................. 3 Remote Control .......................................................... 5 Getting Started .
– 3 – 1 2 3 6 7 8 9 p q w r t u i 5 4 MX-J700 o j l k e / z x c y v b ; a s d f g MX-J500 h Location of the Buttons and Controls Become familiar with the b uttons and controls on your unit. Front Panel Powered Rolling Panel Press P ANEL OPEN/ CLOSE to open the panel.
– 4 – See pages in the parentheses for details. Front Panel 1 Disc trays 2 PO WER button and ST ANDBY lamp (9) 3 Display windo w 4 For MX-J700: SUBW OOFER V OLUME control (10) For MX-J500: A CTIVE B ASS EX. (extension) LEVEL control (10) 5 Remote sensor 6 T APE 2 3 button and lamp (9, 16) Pr essing this button also turns on the unit.
– 5 – When using the remote control, point it at the remote sensor on the front panel. Remote Control Remote Control 1 Disc number buttons (CD1, CD2, and CD3) (13) Pr essing one of these buttons also turns on the unit.
– 6 – Getting Started Unpacking After unpacking, check to be sure that you ha ve all the follo wing items. The number in the parentheses indicates the quantity of the pieces supplied. • AM loop antenna (1) • FM antenna (1) • Remote control (1) • Batteries (2) If any is missing, consult your dealer immediately .
– 7 – 1 Connect the AM loop antenna to the AM LOOP terminals as illustrated. 2 T urn the AM loop antenna until y ou hav e the best r ece ption. T o connect an outdoor AM antenna When reception is poor , connect a single vinyl-covered wir e to the AM EXT terminal and extend it horizontally .
– 8 – For pla ying the other equipment through this unit, connect between the audio output jacks on the other equipment and A UX jacks by using audio cords (not supplied). T o audio output T o start the display demonstration manually Press and hold DEMO f or more than 2 seconds.
– 9 – Common Operations T urning On or Off the Power T o tur n on the unit, press POWER so tha t the ST ANDBY lamp goes off. The Po wered Rolling Panel opens automatically . T o tur n off the unit (on standby), press PO WER again so that the ST ANDBY lamp lights up.
– 10 – When using the remote control, press SUBWOOFER + to increase the subwoofer v olume or press SUBWOOFER – to decrease it. For MX-J500 The ACTIVE B ASS EX. (e xtension) LEVEL control provided for this unit can maintain the richness and fullness of the bass sound while listening to any source at lo w volume.
– 11 – Surround modes * : D.CLUB : Increases resonance and bass. HALL : Adds depth and brilliance to the sound. ST ADIUM : Adds clarity and spreads the sound, like in an outdoor stadium. SEA (Sound Effect Amplifier) modes: R OCK : Boosts lo w and high frequency .
– 12 – Listening to FM and AM Broadcasts T uning in a Station 1 Pr ess FM/AM. The unit automatically turns on and tunes in the previously tuned sta tion (either FM or AM). The P owered Rolling Panel automatically opens. • Each time you press the button, the band alternates between FM and AM.
– 13 – Playing Back CDs Loading CDs On the unit ONL Y : 1 Pr ess 0 f or the disc tray (CD1 to 3) y ou want to load a CD onto. The unit automatically turns on and the disc tray comes out. T he Powered Rolling Panel also opens automatically . 2 Place a disc correctl y on the circle of the disc tray , with its label side up.
– 14 – T o locate a particular point in a track During play , press and hold 1 or ¡ . • 1 : Fast re verses the disc. • ¡ : Fast forw ards the disc. When using the remote control, press and hold 1 / 4 or ¢ / ¡ . T o go to another track Press 4 or ¢ repeatedly before or during playback.
– 15 – T o stop during play , press 7 . • Random play also stops when one of the disc trays is opened. T o exit fr om Random play mode, press PROGRAM/ RANDOM repeatedly again before or after play so that the unit enters another play mode.
– 16 – Playing Back T apes Y ou can play back type I, type II, and type IV tapes without changing any settings. Playing Back a T ape 1 Pr ess EJECT ( 0 ) for the deck y ou want to use. 2 Put a cassette in, with the exposed part of the tape down. 3 Close the cassette holder gently .
– 17 – Recording Recording a T ape on Deck B 1 Press EJECT 0 f or the deck B. 2 Put in a recordab le cassette, with the exposed part of the tape down. 3 Close the cassette holder gently . 4 Check the tape direction of deck B. • If the tape direction is not correct, press T APE 2 3 twice then 7 to change the tape direction.
– 18 – CD Direct Recording Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you hav e made for Program play . 1 Put a recordable cassette into deck B. 2 Place a disc correctl y on the circle of the disc tray , with its label side up.
– 19 – Auto Edit Recording By using Auto Edit Recording, you can record the CD tracks to f it the tape. Auto Edit Recording makes a program by selecting the CD tracks in numerical order . Howe ver , to prev ent the end of the last track on the front side from being cut off , the last track is selected so as to fit on the remaining tape length.
– 20 – Using the T imers There are three timers av ailable — Recording T imer, Daily T imer , and Sleep T imer . Before using the timers, you need to set the clock built in the unit. (See page 9.) Using Daily Timer W ith Daily T imer , you can wake to your fa vorite music or radio program.
– 21 – DAILY Canceled ON TIME ON TIME Clock setting (See page 9.) REC 6 When selecting “– CD – –” 1) Press 4 or ¢ to select the disc number , then press SET . 2) Press 4 or ¢ to set the track number , then press SET . The unit enters volume setting mode.
– 22 – Recording Timer 7:00 6:30 Sleep Timer 7:30 does not work. Recording Timer AM 6:00 7:30 7:00 6:30 Daily Timer AM 6:00 Using Sleep T imer W ith Sleep T imer , you can fall asleep to music. Y ou can set Sleep T imer when the unit is turned on.
– 23 – Maintenance T o get the best performance of the unit, keep your discs, tapes, and mechanism clean. Handling cassette tapes • If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating. • If the tape is loose, it may get stretched, cut, or caught in the cassette.
– 24 – Specifications MX-J700 Amplifier section — CA-MXJ700 Output P ower SUBWOOFERS: 100 W per channel, min. RMS, dri ven into 6 Ω at 63 Hz with no more than 10% total harmonic distortion. MAIN SPEAKERS:50 W per channel, min. RMS, driv en into 6 Ω at 1 kHz with no more than 10% total harmonic distortion.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous.
LIMITED W ARRANTY A UDIO-1 JVC COMP ANY OF AMERICA warrants this product and all parts thereof, e xcept as set for th below ONL Y T O THE ORIGINAL PURCHASER A T RET AIL to be FREE FROM DEFECTIVE MA TERIAL AND WORKMANSHIP from the date of original retail purchase f or the per iod as shown below .
VICTOR COMP ANY OF JAP AN , LIMITED 1299MWMMDWJEM EN J V C MX-J500/700[J].COVER/f 99.12.19, 1:48 PM 2.
VICTOR COMP ANY OF JAP AN , LIMITED 0200MWMMDWJEM EN, FR J V C MX-J500/506/700[C].COVER/1 00.1.8, 8:16 PM 2.
COMP A CT COMPONENT SYSTEM SISTEMAS DE COMPONENTES COMPACTOS SISTEMA DE COMPONENTE COMPACTO MX-J500 Consists of CA-MXJ500 and SP-MXJ550 Consta del CA-MXJ500 el SP-MXJ550 Consta do CA-MXJ500 e SP-MXJ550 For Customer Use: Enter below the Model No. and Serial No.
Caution –– switch! Disconnect the mains plug to shut the power off com- pletely. The switch in any position does not discon- nect the mains line. The power can be remote controlled. Precaución –– Interruptor ! Desconectar el cable de alimentación para desactivar la alimentación totalmente.
CAUTION T o reduce the r isk of elect r ical sho c k s , fir e , etc.: 1 . Do not remo v e scr e ws, c o v ers or cabinet. 2 . Do not e xpose this appliance to r ain or moistur e . PRECAUCIÓN P ara reducir r iesgos de choques eléctrico s , incendi o , etc.
Caution: Proper V entilation T o av oid r isk of electr ic shock and fire, and to pre vent damage , locate the apparatus as f ollows: 1 Front: No obstructions and open spacing. 2 Sides/ T op/ Back: No obstr uctions should be placed in the areas shown b y the dimensions below .
IMPORTANT FOR LASER PRODUCTS / IMPORTANTE PARA PRODUCTOS LÁSER / IMPOTANTE PARA PRODUTOS LASER / / REPRODUCTION OF LABELS / REPRODUCCIÓN DE ETIQUETAS / REPRODUÇÃO DE ETIQUETAS / 1 CLASSIFICATION L.
– 1 – English Introduction About This Manual This manual is org anized as follows: • The manual mainly explains operations using the b uttons and controls on the unit. Y ou can also use the b uttons on the remote control if they ha ve the same or similar names (or marks) as those on the unit.
– 2 – English Contents Location of the Buttons and Controls ....................... 3 Front Panel ................................................................. 3 Remote Control .......................................................... 5 Getting Started .
– 3 – English 1 2 p q w e r y u o ; 7 4 8 5 6 9 t i 3 a l z / x c v b n m s d f g h j k Location of the Buttons and Controls Become familiar with the b uttons and controls on your unit. Front Panel Powered Rolling Panel Press P ANEL OPEN/ CLOSE to open the panel.
– 4 – English See pages in the parentheses for details. Front Panel 1 Disc trays 2 (Standby/On) button and ST ANDBY lamp (9) 3 Display windo w 4 A CTIVE BASS EX. (e xtension) LEVEL control (10) 5 Remote sensor 6 T APE 2 3 button and lamp (9, 16) Pr essing this button also turns on the unit.
– 5 – English When using the remote control, point it at the remote sensor on the front panel. Remote Control Remote Control 1 Disc number buttons (CD1, CD2, and CD3) (13) Pr essing one of these buttons also turns on the unit.
– 6 – English Getting Started Unpacking After unpacking, check to be sure that you ha ve all the follo wing items. The number in the parentheses indicates the quantity of the pieces supplied.
– 7 – English 1 Connect the AM loop antenna to the AM LOOP terminals as illustrated. 2 T urn the AM loop antenna until y ou hav e the best r ece ption. T o connect an outdoor AM antenna When reception is poor , connect a single vinyl-covered wir e to the AM EXT terminal and extend it horizontally .
– 8 – English For pla ying the other equipment through this unit, connect between the audio output jacks on the other equipment and A UX jacks by using audio cords (not supplied). Adjusting the V oltage Selector Before plugging in the unit, set the correct voltage for your area with the voltage selector on the rear of the unit.
– 9 – English Common Operations T urning On and Off the Power T o tur n on the unit, press so that the ST ANDBY lamp goes off. The Po wered Rolling Panel opens automatically . T o tur n off the unit (on standby), press again so that the ST ANDBY lamp lights up The Po wered Rolling Panel also closes.
– 10 – English Adjusting the V olume Y ou can adjust the volume le vel only while the unit is turned on. T ur n the V OLUME control clockwise to increase the volume or counter clockwise to decrease it. • The v olume level can be adjusted in 32 steps (MIN, V OL 1 — VOL 30, and MAX).
– 11 – English Surround modes * : D.CLUB : Increases resonance and bass. HALL : Adds depth and brilliance to the sound. ST ADIUM : Adds clarity and spreads the sound, like in an outdoor stadium. SEA (Sound Effect Amplifier) modes: R OCK : Boosts lo w and high frequency .
– 12 – English Listening to FM and AM Broadcasts T uning in a Station 1 Pr ess FM/AM. The unit automatically turns on and tunes in the previously tuned sta tion (either FM or AM). The P owered Rolling Panel automatically opens. • Each time you press the button, the band alternates between FM and AM.
– 13 – English Playing Back CDs Loading CDs On the unit ONL Y : 1 Pr ess 0 f or the disc tray (CD1 to 3) y ou want to load a CD onto. The unit automatically turns on and the disc tray comes out. T he Powered Rolling Panel also opens automatically .
– 14 – English T o locate a particular point in a track During play , press and hold 1 or ¡ . • 1 : Fast re verses the disc. • ¡ : Fast forw ards the disc. When using the remote control, press and hold 1 / 4 or ¢ / ¡ . T o go to another track Press 4 or ¢ repeatedly before or during playback.
– 15 – English T o stop during play , press 7 . • Random play also stops when one of the disc trays is opened. T o exit fr om Random play mode, press PROGRAM/ RANDOM repeatedly again before or after play so that the unit enters another play mode.
– 16 – English Playing Back T apes Y ou can play back type I, type II, and type IV tapes without changing any settings. Playing Back a T ape 1 Pr ess EJECT ( 0 ) for the deck y ou want to use. 2 Put a cassette in, with the exposed part of the tape down.
– 17 – English Recording Recording a T ape on Deck B 1 Press EJECT 0 f or the deck B. 2 Put in a recordab le cassette, with the exposed part of the tape down. 3 Close the cassette holder gently . 4 Check the tape direction of deck B. • If the tape direction is not correct, press T APE 2 3 twice then 7 to change the tape direction.
– 18 – English CD Direct Recording Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you hav e made for Program play . 1 Put a recordable cassette into deck B. 2 Place a disc correctl y on the circle of the disc tray , with its label side up.
– 19 – English Auto Edit Recording By using Auto Edit Recording, you can record the CD tracks to f it the tape. Auto Edit Recording makes a program by selecting the CD tracks in numerical order .
– 20 – English Using the Microphones Y ou can enjoy singing along (Karaoke) and microphone mixing by using two microphones. • The MIC LEVEL control adjustment is v alid for both microphones connected the MIC 1 and MIC 2 jacks. IMPORT ANT : • Always set the MIC LEVEL to MIN when connecting or disconnecting the microphone.
– 21 – English Using the T imers There are three timers av ailable — Recording T imer, Daily T imer , and Sleep T imer . Before using the timers, you need to set the clock built in the unit. (See page 9.) Using Daily Timer W ith Daily T imer , you can wake to your fa vorite music or radio program.
– 22 – English DAILY Canceled ON TIME ON TIME Clock setting (See page 9.) REC 6 When selecting “– CD – –” 1) Press 4 or ¢ to select the disc number , then press SET . 2) Press 4 or ¢ to set the track number , then press SET . The unit enters volume setting mode.
– 23 – English does not work. Using Sleep T imer W ith Sleep T imer , you can fall asleep to music. Y ou can set Sleep T imer when the unit is turned on. How Sleep Timer actually works The unit automatically turns of f after the specified time length passes.
– 24 – English Maintenance T o get the best performance of the unit, keep your discs, tapes, and mechanism clean. Handling cassette tapes • If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating.
– 25 – English If you are ha ving a pr oblem with your unit, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints gi ven here, or the unit has been physically damaged, call a qualif ied person, such as your dealer , for service.
– 26 – English Specifications Amplifier section — CA-MXJ500 Output Po w er (IEC 268-3/DIN) 72 W per channel, min. RMS, both channels driven into 6 Ω at 1 kHz with no more than 0.9% total harmonic distortion. Audio input sensitivity/Impedance (a t 1 kHz) A UX: 420 mV/50 k Ω MIC 1/2: 3.
VOLTAGE SELECTOR 110V 220V 127V 230V -240V ANTENNA AUX AM EXT RIGHT LEFT AM LOOP SPEAKERS RIGHT LEFT VOLTAGE SELECTOR 110V 220V 127V 230V -240V COAXIAL FM 75 Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia, and U.K.) Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté JVC MX-J700 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du JVC MX-J700 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation JVC MX-J700, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le JVC MX-J700 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le JVC MX-J700, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du JVC MX-J700.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le JVC MX-J700. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei JVC MX-J700 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
