Manuel d'utilisation / d'entretien du produit HR-S9400EK du fabricant JVC
Aller à la page of 68
H R-S9400EK VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0002-0D9A TM SEE QUICK SET UP GUIDE ON REAR SIDE SEE QUICK SET UP GUIDE ON REAR SIDE 625 AUTO SP/LP TIMER TIMER STANDBY/ON SP/LP 8 S L O W S L O W REW FF TV PROG/ JOG SHUTTLE S C E N E F I N D E R P R O G C H E C K T V V O L C.
2 SAFETY FIRST IMPORT ANT n Please read the various precautions on p. 2 – 3 of this instruction manual before installing or operating the recorder . n It should be noted that it may be unlawful to r.
3 This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
4 INST ALLING YOUR NEW RECORDER Basic Connections CONNECT RECORDER TO MAINS 4 Plug the end of the mains power cord into a mains outlet. 21-pin AV input connector (SCAR T) Aerial connector It's essential that your video recorder be properly connected.
5 AV1 OUT COMP. Y/C AV1 IN/OUT RF OUT AV2 IN PAUSE/ R.A.EDIT ANT.IN R R L L AUDIO IN OUT S IN OUT TV Aerial Cable (not provided) A TTENTION If you have finished all the necessary connections, go to.
6 AV1 IN/OUT AV2 IN PAUSE/ R.A.EDIT AV1 OUT A N COMP. Y/C R R L L AUDIO S IN IN OUT OUT INST ALLING YOUR NEW RECORDER (cont.) CONNECT RECORDER TO TV 1 a– Connect the aerial, recorder and TV as per "RF CONNECTION" ( Z pg. 4). b– Connect the recorder's S OUT connector to the TV's S-VIDEO IN connector.
7 RF OUT N T.IN Back of TV S-V ideo cable (provided) A TTENTION If you have finished all the necessary connections, go to "V ideo Channel Set" on page 8, then perform Auto Set Up on page 10; do NOT press the button on the recorder/remote control to turn on the recorder's power before you start Auto Set Up.
8 V ideo Channel Set V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.
9 12 45 3 6 8 0 7 9 2 4 1 3 IMPORT ANT : Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder .
10 Auto Set Up Auto Channel Set/Auto Clock Set/Auto Guide Program Number Set The Auto Set Up function sets the tuner channels, clock and V ideo Plus+ assigned Guide Program numbers automatically when the button on the recorder/remote is first pressed to power on the recorder after you plug the mains power cord into a mains outlet.
11 Auto Set Up results appear on the display panel a) When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed. b) When auto channel set has been completed successfully but auto clock set has not, "CH" will be displayed.
12 V ideo Plus+ Setup T urn on the TV and select the VIDEO channel (or A V mode). INITIAL SETTINGS (cont.) 12 45 3 6 8 0 7 9 2 4 1 3 NUMBER OK TV PROG MENU 4,5 2,6 3,4,5 3,5 IMPORT ANT As Channel 5 ha.
13 When Using A Satellite Receiver And/Or Cable System THE SA TELLITE RECEIVER IS SHOWN CONNECTED TO THE “A V2 IN” (SCAR T) CONNECTOR AND THE CABLE SYSTEM CONNECTED VIA THE AERIAL SOCKET AND TUNED T O, FOR EXAMPLE, PRESET POSITION 6 ON YOUR TV .
14 PLA YBACK Basic Playback The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
15 8 •• • • •• •• • • • •• • • •• •• • • • Playback Features 8 0 7 9 4 1 3 PAUSE PUSH JOG Still Picture/Frame-By-Frame Playback P AUSE DURING PLA YBACK 1 Press P AUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture.
16 12 45 3 6 8 0 7 9 2 4 1 3 TV PROG REVIEW 8 •• • • •• •• • • • •• • • •• •• • • • FF REW PLA YBACK (cont.) C.RESET PUSH JOG C. MEMORY STOP Manual T racking Y our video recorder is equipped with automatic tracking control.
17 Instant ReView Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer -recorded programme. If you have several programmes recorded, you can easily access any of them. NOTE: Before starting, make sure that the recorder is off and that the T imer mode is disengaged.
18 PLA YBACK (cont.) Soundtrack Selection Y our video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.
19 ACTIV A TE SCENE FINDER 1 Press SCENE FINDER . The recorder starts forward search for 5 seconds and then fast-forwards 10 minutes on the counter. This cycle is repeated until the end of the tape is reached. ● T o start Scene Finder in the reverse direction, press SCENE FINDER and then press the REW button within 2 seconds.
20 PLA YBACK (cont.) TimeScan Y our recorder is equipped with the TimeScan function. T imeScan allows noise free pictures to be displayed on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during any of the T imeScan modes ( Z pg.
21 Names of special-ef fects playback Reverse Forward Search Play Slow-Motion *Still Slow-Motion Play Search -9x -7x -5x -3x -1x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 3x 5x 7x 9x -7x -3x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 5x 9x Audio is output. Audio is not Audio is Audio is not Audio is output.
22 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. Y ou can “capture” a TV programme using your video recorder . RECORDING Basic Recording T urn on the TV and select the VIDEO channel (or A V mode).
23 Recording Features Record One Pr ogramme While W atching Another 12 45 3 6 8 0 7 9 2 4 3 8 •• • • •• •• • • • •• • • •• •• • • • Elapsed Recording Time Indication Y ou can check the exact time of a recording.
24 S-VHS (Super VHS) and VHS Y our recorder can record in either S-VHS or VHS. T o record in S-VHS; ● perform the steps 1 – 4 below to set the "S-VHS" to "AUT O". ● then, insert a cassette marked "S-VHS", the "S" (S-VHS) indicator will light on the display panel.
25 ADJUST AUDIO RECORDING LEVEL 1 T urn Hi-Fi REC LEVEL in either direction. ● When the level indicator lights up to or near 0dB with the loudest signal being applied, the recording level is optimum. NOTES: ● Make sure that the "HI-FI L+R" position is selected with the AUDIO MONITOR button.
26 Video Plus+ Timer Recording TIMER RECORDING Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. W ith this system, special code signals are transmitted together with the audio/video signals.
27 – P1 – VIDEO PLUS+ 123456789 ST ART STOP 21:00 = 22:00 SP OFF DA TE TV PROG 25.12 1 BBC 1 : OK ACCESS VIDEO PLUS+ PROGRAM SCREEN 3 Press OK , and the V ideo Plus+ Program screen appears (if you’re just starting out, “P1” appears). The display panel shows the programme start time.
28 Regular Timer Pr ogramming Remember , the clock must be set before you can progamme the timer ( Z pg. 56). Before performing the following steps: ● Insert a cassette with the safety tab in place. The recorder will come on automatically . ● T urn on the TV and select the VIDEO channel (or A V mode).
29 ENTER PROGRAMME DA TE 5 Press DA TE +/– . (The current date appears on screen. The date you enter appears in its place.) ● If you are using the Illumi-Guide feature, the following buttons remain lit: ST ART +/– , STOP +/– , DA TE +/– , TV PROG +/– and MENU .
30 Check And Cancel Programmes ACCESS PROGRAMME DISPLA Y AND/OR SCREEN 1 Press PROG CHECK. ● The display panel shows the programme start time. Pressing OK changes the display to the programme stop time, then the date and preset position.
31 Auto SP/LP Timer If, when recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording. ENGAGE AUTO SP/LP TIMER 1 Press AUTO SP/LP TIMER on the recorder front panel.
32 Preparation For Editing ● T urn on the TV and select the VIDEO channel (or A V mode). Editing Mode Setting Y ou can minimize picture degradation while editing. ACCESS MAIN MENU SCREEN 1 Press MENU twice. ACCESS MODE SET SCREEN 2 Move the highlight bar (pointer) to "MODE SET" by pressing PUSH JOG % fi , then press OK .
33 T o Select The External Input Mode T o record external audio and video signals; 1 Press the remote control's NUMBER key "0". 2 Press A V/S SELECT on the front of the recorder to select the appropriate external input mode.
34 EDITING (cont.) Edit T o Or Fr om Another V ideo Recorder Y ou can use your video recorder as the source player or the recording deck. MAKE CONNECTIONS 1 Connect the player’s 21-pin SCAR T connector to the recorder’s 21-pin SCAR T connector as illustrated on the below .
35 Y ou can use a camcorder as the sour ce player and your video recorder as the recorder . Edit Fr om A Camcorder 12 45 3 6 8 0 7 9 2 4 1 3 MAKE CONNECTIONS 1 Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder ’ s front panel AUDIO/VIDEO input connectors.
36 This function makes it easier to create edited videos when your video recorder is used as the source player in combination with another JVC video recorder equipped with a Remote P AUSE Connector . Y ou can pre-program up to 8 scenes or “cuts” for automatic editing in the sequence you have specified.
37 LOCA TE EDIT -IN POINT 8 Find the point on the source tape from where you want the edited scene to begin by pressing PUSH JOG or using the TIME SCAN SHUTTLE ring or the JOG dial, then press IN/OUT . ● The edit-in point is registered in memory and appears on the screen.
38 Insert editing replaces part of the recorded scene with new material. Both the picture and Hi-Fi audio soundtrack are replaced with new ones, while the normal audio soundtrack remains unchanged. If you wish to change the normal audio track as well, use the audio dubbing function simultaneously .
39 ENGAGE INSER T EDITING 6 Press INSERT . ● Y our recorder enters the Insert-Pause mode. (" ", " " and " " light up on the front display panel.) ● The TV screen changes from the still picture to the input source you are going to record.
40 EDITING (cont.) Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack. Audio Dubbing 8 •• • • •• •• • • • •• • • •• •• • • • 8 •• • • •• •• • • • •• • • •• •• • • • A.
41 INFORMA TION ON J TERMINAL J T erminal (JLIP(Joint Level Interface Protocol) Connector) The J T erminal is used to connect the recorder to a personal computer or similar device to allow computerized control of the recorder during editing and certain other operations.
42 SYSTEM CONNECTIONS Connecti o n T o A Stereo System These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo. MAKE CONNECTIONS 1 a– Connect the AUDIO IN L and R on your video recorder to the audio output connectors on your amplifier .
43 AV1 IN/OUT RF OUT AV2 IN PAUSE/ R.A.EDIT AV1 OUT ANT.IN COMP. Y/C R R L L AUDIO S IN IN OUT OUT DECODER VCR TV EXT.2 EXT.1 Connection T o A Satellite Receiver The A V2 IN connector on the rear panel of your recorder allows simple connection to a satellite receiver .
44 T urn on the TV and select the VIDEO channel (or A V mode). The superimposed indication on the TV screen tells you what the recorder is doing. 1– Operation mode indicators 2– Preset position number and station name/Aux.
45 Receiving NICAM Stereo And Bilingual Pr ogrammes Y our recorder is equipped with a Digital stereo sound decoder (NICAM), making reception of stereo and bilingual broadcasts possible. When the recorder is tuned to a different station, the type of broadcast being received will be displayed on the TV screen for a few seconds.
46 SPECIAL FEA TURES (cont.) Contr ol Y our TV Using Additional Buttons The NUMBER keys on the remote can also be used to select the TV’ s channel by setting the remote control to the TV mode.
47 12 45 3 6 8 0 7 9 2 4 1 3 NUMBER STOP Satellite Receiver Multi- Brand Remote Contr ol Y our remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’ s satellite receivers can also be controlled by setting the appropriate switch on the remote control.
48 TUNER SET Auto Channel Set IMPORT ANT Perform the following steps only if auto channel set has not been set correctly by Auto Set Up function ( Z pg. 10) or if you have moved to a different area or if a new station starts broadcasting in your area.
49 12 45 3 6 8 0 7 9 2 4 1 3 VIEW CONFIRMA TION SCREEN 4 The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID – Z pg. 54). T o view the next page of the listing, press PUSH JOG %fi .
50 Manual Channel Set TUNER SET (cont.) Storing Channels Manually Store channels that were not stored during Auto Set Up ( Z pg. 10) or Auto Channel Set ( Z pg. 48). ACCESS MAIN MENU 1 Press MENU twice. ACCESS CONFIRMA TION SCREEN 2 Press PUSH JOG %fi to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK .
51 12 45 3 6 8 0 7 9 2 4 1 3 PUSH JOG Perform steps 1 and 2 of "Storing Channels Manually" on page 5 0 to access the C onfirmation screen before continuing. Change Station Preset Position SELECT ITEM 1 Press PUSH JOG % fi until the item you want to move begins blinking.
52 12 45 3 6 8 0 7 9 2 4 1 3 PUSH JOG Perform steps 1 and 2 of "Storing Channels Manually" on page 5 0 to access the C onfirmation screen before continuing. SELECT ITEM 1 Press PUSH JOG %fi until the item you want begins blinking. Then press OK twice and the station’ s name (ID) begins blinking.
53 12 45 3 6 8 0 7 9 2 4 1 3 OK PUSH JOG Perform steps 1 and 2 of "Storing Channels Manually" on page 5 0 to access the C onfirmation screen before continuing. SELECT CHANNEL TO FINE-TUNE 1 Press PUSH JOG % fi until the channel you want to tune begins blinking.
54 TV Station And ID List ST A TION NAME ID* Anglia TV ANGL ARD ARD ARTE AR TE BBC Group BBC BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BR T1 BRT1 BR T2 BRT.
55 TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from BBC and ITC. BBC1 BBC2 ITV CH4 London & South-East Bluebell Hill .............................. 40 46 43 65 Crystal Palace .
56 CLOCK SET IMPORT ANT Perform the following steps only if Auto Clock Set has not been performed correctly by Auto Set Up ( Z pg. 10) or Auto Channel Set ( Z pg.
57 12 45 3 6 8 0 7 9 2 4 1 3 OK NOTES: ● Just Clock (when set to "ON") adjusts the recorder's built-in clock every hour , except for 23:00, 0:00, 1:00 and 2:00. ● Just Clock is not effective when . . . – the recorder’s power is on (unless the recorder is tuned to the same preset selected in the Clock Set screen).
58 TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair . POSSIBLE CAUSE ● The mains power cord is discon- nected.
59 Confirm that the camcorder is properly connected. Set the input mode to “AU”. ● The camcorder has not been properly connected. ● The input mode is not correct. 4. Camcorder recording is not possible. CORRECTIVE ACTION Re-perform the clock and/or timer settings.
60 QUESTIONS AND ANSWERS PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
61 GENERAL Power requirement : AC 220 – 240 V ` , 50/60 Hz Power consumption : 29 W T emperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 465 x 105 x 353 mm W eight : 5.6 kg Format : S-VHS/VHS P AL standard Maximum recording time (SP) : 240 min.
62 FRONT VIEW INDEX A.DUB START INSERT HEAD PHONE VOLUME Hi-Fi REC LEVEL VIDEO 01 0 01 0 (MONO) L–AUDIO–R IN/OUT •• • • •• •• • • • •• • • •• •• • • • AV/S SELECT SPATIALIZER R.
63 ! TIME SCAN Indicator lights during T imeScan mode. Z pg. 20 @ TIME SCAN SHUTTLE Ring rewinds or fast- forwards tape during Stop mode Z pg. 14; performs forward and reverse slow-motion and search (T imeScan) during Still or Play mode. Z pg. 15, 20 # TV PROG Dial scans to desired preset position during Stop mode.
64 REAR VIEW AV1 IN/OUT RF OUT AV2 IN PAUSE/ R.A.EDIT AV1 OUT ANT.IN COMP. Y/C R R L L AUDIO S IN IN OUT OUT 6 5 4 2 3 9 7 0 ! 1 8 1 Mains Power Cord supplies power to recorder . Z pg. 4, 6 2 S-VIDEO IN Connector enables S-VIDEO connection to camcorder or second recorder; input recordable when "[S]" selected.
65 1 Audio Level Indicator displays audio input and output levels. Z pg. 25 2 Symbolic Mode Indicators 3 S-VHS Indicator lights when a cassette marked S-VHS is inserted with S-VHS mode to "AUTO" and playback a S-VHS recorded tape. Z pg. 2 4 4 "Timer" Indicator lights when the TIMER button has been pressed to engage T imer mode.
66 INDEX (cont.) S C E N E F I N D E R P R O G C H E C K T V V O L C.MEMORY DISPLAY DAILY AUX ADD TIME C.RESET CANCEL DATE STOP START AUDIO MONITOR (MONITOR) TV/VCR TV SAT VCR TIMER WEEKLY A 12 45 3 6.
67 ( ADD TIME Button adds time to end of V ideo Plus+ timer recording (5 minutes each time button is pressed.) Z pg. 27 ) DAIL Y Button enables timer recording of daily serials. Z pg. 27, 29 q WEEKLY Button enables timer recording of weekly serials. Z pg.
VICTOR COMP ANY OF JAPAN, LIMITE D.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté JVC HR-S9400EK c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du JVC HR-S9400EK - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation JVC HR-S9400EK, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le JVC HR-S9400EK va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le JVC HR-S9400EK, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du JVC HR-S9400EK.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le JVC HR-S9400EK. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei JVC HR-S9400EK ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
