Manuel d'utilisation / d'entretien du produit HR-DD848E du fabricant JVC
Aller à la page of 56
H R-DD848E/EH VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0002-0C4B SEE AUTO SET UP ON REAR SIDE SEE AUTO SET UP ON REAR SIDE PAL S C E N E F I N D E R P R O G C H E C K T V V O L .
2 EN SAFETY FIRST Failure to heed the following precautions may result in damage to the recorder , remote control or video cassette. 1. DO NOT place the recorder . . . ... in an environment prone to extreme temperatures or humidity . ... in direct sunlight.
EN 3 Basic Connections CHECK CONTENTS 1 Make sure the package contains all of the accessories listed in “Specifications” ( Z pg. 55). SITUA TE RECORDER 2 Place the recorder on a stable, horizontal surface. CONNECT RECORDER TO TV 3 The connection method you use depends on the type of TV you have.
4 EN INITIAL SETTINGS When the button on the recorder/remote control is pressed for the first time to power on the recorder after you plug the mains power cord into a mains outlet, the Country Set display will appear on the TV screen and the recorder's front display panel.
EN 5 If you are referring to the on-screen display Press PUSH JOG % fi to move the highlight bar (pointer) to your country's name. ● If you have selected a country other than BELGIUM or SUISSE, go to step 4 . ● If you have selected BELGIUM or SUISSE, go to step 3 .
6 EN INITIAL SETTINGS (cont.) If both auto channel set and auto clock set have been performed successfully: 1 Perform "V ideo Channel Set" on page 8. 2 T urn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in the recorder's memory by using the TV PROG button(s).
EN 7 Language This recorder offers you the choice to view on-screen messages in 10 different languages. Though Auto Set Up selects the language automatically ( Z pg. 6), you can change the language setting manually using this procedure as required. TURN ON THE RECORDER 1 Press .
8 EN V ideo Channel Set INITIAL SETTINGS (cont.) V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.
EN 9 IMPORT ANT : Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder . ACCESS VIDEO CHANNEL SET MODE 1 Hold down STOP on the recorder until the display panel shows the following.
10 EN INITIAL SETTINGS (cont.) S HOW V IEW Setup W ith S HOW V IEW , timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.
EN 11 ENTER SHOWVIEW NUMBER 4 Press OK , and a cursor appears above “GUIDE PROG”. Then, using the NUMBER keys, input the S HOW V IEW number (found in most TV listings) of a program scheduled to be broadcast on each station on the list from step 1 , starting at the top.
12 EN PLA YBACK Basic Playback The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
EN 13 Playback Features High-Speed (T urbo) Sear ch ACTIV A TE HIGH-SPEED SEARCH 1 During playback or still picture, press FF for forward high-speed search, or REW for reverse high-speed search. T o resume normal playback, press PLA Y . NOTES: ● For short searches, press and hold FF or REW for over 2 seconds.
14 EN Manual T racking Y our video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons. OVERRIDE AUTOMA TIC TRACKING 1 Press SP/LP ( ) on the remote to engage manual tracking.
EN 15 NTSC Playback Y our video recorder is equipped with NTSC circuitry that can play back NTSC tapes. LOAD A CASSETTE 1 Insert a cassette recorded in NTSC. ST AR T PLA YBACK 2 Press PLAY . ● "NTSC" appears on the screen for about 5 seconds.
16 EN PLA YBACK (cont.) Spatializer W Soundtrack Selection Y our video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.
EN 17 ACTIV A TE SCENE FINDER 1 Press SCENE FINDER . The recorder starts forward search for 5 seconds and then fast-forwards 10 minutes on the counter. This cycle is repeated until the end of the tape is reached. ● T o start Scene Finder in the reverse direction, press SCENE FINDER and then press the REW button within 2 seconds.
18 EN PLA YBACK (cont.) TimeScan Y our recorder is equipped with the TimeScan function. T imeScan allows noise free pictures to be displayed on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during any of the T imeScan modes ( Z pg.
EN 19 Names of special-ef fects playback Reverse Forward Search Play Slow-Motion *Still Slow-Motion Play Search -9x -7x -5x -3x -1x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 3x 5x 7x 9x -7x -3x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 5x 9x Audio is output. Audio is not Audio is Audio is not Audio is output.
20 EN TimeScan Audio The audio output can be set ON/OFF during T imeScan. Select ON/OFF as required. * The default setting is "ON". ACCESS MAIN MENU SCREEN 1 Press MENU twice. ACCESS MODE SET SCREEN 2 Move the highlight bar (pointer) to "MODE SET" by pressing PUSH JOG % fi , then press OK .
EN 21 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. Y ou can “capture” a TV programme using your video recorder . RECORDING Basic Recording 12 45 3 6 8 0 7 9 2 4 1 3 q S L O W S L O W PAUSE NUMBER PLAY T urn on the TV and select the VIDEO channel (or AV mode).
22 EN B.E.S.T . Pictur e System The B.E.S.T . (Biconditional Equalised Signal T racking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”.
EN 23 12 45 3 6 8 0 7 9 2 4 1 3 q S L O W S L O W PAUSE RECORD NOTES: ● The B.E.S.T . system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. ● In the case of timer recording, the B.
24 EN On-Screen Displays Y ou can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF . Messages appear in the selected language ( Z pg. 6 or 7). T urn on the TV and select the VIDEO channel (or AV mode).
EN 25 Recording Features Record One Pr ogramme While W atching Another If your recorder is connected to the TV via A V connection, . . . . . . press TV/VCR .
26 EN Receiving Stereo And Bilin- gual Programmes Y our recorder is equipped with a Sound-Multiplex decoder (A2) and, if you own the HR-DD848 EH, a Digital stereo sound decoder (NICAM) as well, making reception of stereo and bilingual broad- casts possible.
EN 27 Instant Timer Recording (ITR) This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished. q S L O W S L O W ST AR T RECORDING 1 Press RECORD on the recorder .
28 EN TIMER RECORDING S HOW V IEW Timer Recording ACCESS TIMER PROGRAMMING SCREEN 1 Press PROG . The front display panel looks like this: ENTER SHOWVIEW NUMBER 2 Press the NUMBER keys to enter the S HOW V IEW number of a programme you wish to record. ● If you make a mistake, press CANCEL to backspace and then input the correct number .
EN 29 ● Make sure the channel position number you wish to record is displayed; if not, see "S HOW V IEW Setup" on page 10 and set the Guide Program number for that S HOW V IEW number correctly . ● If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel.
30 EN TIMER RECORDING(cont.) Regular Timer Pr ogramming Remember , the clock must be set before you can programme the timer ( Z pg. 47). If you don’ t know the S HOW V IEW number for the programme you wish to record, use the following procedure to set your recorder to timer -record the programme.
EN 31 ENTER CHANNEL POSITION 6 Press TV PROG +/– . IMPORT ANT Be sure to confirm the setting of PDC/VPS recording. ● If " ON" is displayed on the screen or " " is lit on the display panel, PDC/VPS is set to ON.
32 EN 12 45 3 6 8 0 7 9 2 4 1 3 OK CANCEL START+/– DATE+/– STOP+/– Auto Timer When the Auto T imer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on.
EN 33 Auto SP/LP Timer If, when recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording. ENGAGE AUTO SP/LP TIMER 1 Press AUTO SP/LP TIMER on the recorder front panel.
34 EN EDITING Edit T o Or Fr om Another V ideo Recorder Y ou can use your video recorder as the source player or the recording deck. MAKE CONNECTIONS 1 Connect the player’s 21-pin SCAR T connector to the recorder’s 21-pin SCAR T connector as illustrated on page 35.
EN 35 RF Cable (provided) Another recorder Recorder 21-pin SCAR T Cable (not provided) Player Y our recorder Recorder Y our recorder TV Receiver TV Receiver Player VIDEO CHAN- NEL or A V mode VIDEO CH.
36 EN Y ou can use a camcorder as the source player and your video recorder as the recorder . Edit Fr om A Camcorder MAKE CONNECTIONS 1 Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder ’ s front panel AUDIO/VIDEO input connectors.
EN 37 q S L O W S L O W q S L O W S L O W Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack. Audio Dubbing MAKE CONNECTIONS 1 Connect an audio component to the AUDIO IN L + R connectors on the recorder's front panel.
38 EN The A V2 IN/DECODER connector can be used as an input terminal for an external decoder (descrambler). Simply connect a decoder and you can enjoy the variety of programming that is available through scrambled channels. SELECT INPUT MODE 1 Set "A V2 SELECT " to "DECODER".
EN 39 Connecting/ Using A Stereo System These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.
40 EN TV Multi- Brand Remote Contr ol SPECIAL FEA TURES Y our remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer ’ s TVs can also be controlled by setting the appropriate switch on the remote control.
EN 41 Y our remote control can operate the basic functions of your satellite tuner set. In addition to JVC satellite tuner s, other manufacturer’ s satellite tuners can also be controlled by setting the appropriate switch on the remote control. Before you start .
42 EN T urn on the TV and select the VIDEO channel (or AV mode). IMPORTANT Perform the following steps only if auto channel set has not been set correctly by Auto Set Up function ( Z pg. 4) or if you have moved to a different area or if a new station starts broadcasting in your area.
EN 43 12 45 3 6 8 0 7 9 2 4 1 3 OK PUSH JOG AUTO SET PLEASE W AIT [MENU] : EXIT 0 + ++ PERFORM AUTO CHANNEL SET 5 Press PUSH JOG % fi to move the highlight bar (pointer) to the language of your choice , then press OK to initiate Auto Channel Set.
44 EN Storing Channels Manually Store channels that were not stored during Auto Set Up ( Z pg. 4) or Auto Channel Set ( Z pg. 42). TUNER SET (cont.) Change Station Channel Position SELECT ITEM 1 Press PUSH JOG % fi until the item you want to move begins blinking.
EN 45 Fine-T uning Channels Already Stored Perform steps 1 and 2 of "Storing Channels Manually" on page 4 4 to access the Confirmation screen before continuing. Set Stations (A) SELECT ITEM 1 Press PUSH JOG %fi until the item you want begins blinking.
46 EN TUNER SET (cont.) TV Station And ID List ID* ST ATION NAME 1000 TV1000 3SA T 3SAT ADL T ADUL T ANT3 ANTENA3 ARD ARD ARTE AR TE BBC BBC GROUP BBC1 BBC1 BBC2 BBC2 BR3 BA YERN3 C+ CANAL PLUS C1 POR.
EN 47 T urn on the TV and select the VIDEO channel (or AV mode). CLOCK SET 12 45 3 6 8 0 7 9 2 4 1 3 PUSH JOG OK IMPORT ANT Perform the following steps only if auto clock set has not been set correctly by Auto Set Up function ( Z pg. 4) or Auto Channel Set ( Z pg.
48 EN CLOCK SET (cont.) SET CLOCK AUTOMA TICALL Y 4 At the Clock Set screen, press PUSH JOG . The Auto Clock screen appears and clock setting begins. ● If "TV PR." isn't set to the channel position on which Auto Clock data is received, "ERROR" appears, and then the screen from step 3 reappears.
EN 49 TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair . POSSIBLE CAUSE ● The mains power cord is discon- nected.
50 EN Confirm that the camcorder is properly connected. Set the input mode to “AU”. ● The camcorder has not been properly connected. ● The input mode is not correct. 4. Camcorder recording is not possible. TROUBLESHOOTING (cont.) TIMER RECORDING CORRECTIVE ACTION Re-perform the clock and/or timer settings.
EN 51 QUESTIONS AND ANSWERS PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
52 EN INDEX FRONT VIEW SPATIALIZER 3R PICTURE q STANDBY/ ON REW FF TV PROG / JOG SHUTTLE VIDEO ( MONO ) L – AUDIO – R AUTO SP/LP TIMER TIMER TV PROG COUNTER RESET A.
EN 53 REAR VIEW 5 A V2 IN/DECODER Connector Z pg. 34, 38 6 Remote PAUSE Connector Z pg. 36 7 RF OUT Connector Z pg. 3 1 Mains Power Cord Z pg. 3 2 A V1 IN/OUT Connector Z pg. 3, 34 3 ANT . IN Connector Z pg. 3 4 AUDIO OUT (L/R) Connectors Z pg. 39 AV1 IN / OUT AV2 IN/DECODER RF OUT ANT.
54 EN REMOTE CONTROL INDEX (cont.) Buttons with a small dot on the left side of the name can also be used to operate your TV with the TV/ SA T/VCR switch set to "TV". Z pg. 40 1 REVIEW Button Z pg. 15 2 A/B Code Switch Z pg. 17 3 C. MEMOR Y Button Z pg.
EN 55 SPECIFICA TIONS GENERAL Power requirement : AC 220 – 240 V ` , 50/60 Hz Power consumption : 24 W T emperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 400 x 94 x 340 mm W eight : 4.
HR-DD848E/EH COPYRIGHT © 1997 VICTOR COMPANY OF JAPAN, LTD. E/EH Printed in Japan 0697HOV * UN * VP VICTOR COMP ANY OF JAPAN, LIMITED Auto Set Up – referring to the display panel The Auto Set Up function sets the tuner channels, clock and Guide Program numbers automatically .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté JVC HR-DD848E c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du JVC HR-DD848E - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation JVC HR-DD848E, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le JVC HR-DD848E va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le JVC HR-DD848E, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du JVC HR-DD848E.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le JVC HR-DD848E. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei JVC HR-DD848E ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
