Manuel d'utilisation / d'entretien du produit DT-V1900CG du fabricant JVC
Aller à la page of 31
INSTR UCTIONS DT -V1900CG MUL TI-FORMA T MONIT OR BEDIENUNGSANLEITUNG : MUL TI-SYSTEM-MONIT OR MANUEL D’INSTR UCTIONS : MONITEUR MUL TI-FORMA T MANU ALE DI ISTR UZIONI : MONIT OR MUL TI-FORMA TI INS.
ENGLISH INSTRUCTIONS MUL TI-FORMA T MONIT OR DT -V1900CG Thank you for purchasing this JVC Multi-Format Monitor . Before using it, read and follow all instructions carefully to take full advantage of the monitor ’ s capabilities. For Customer Use: Enter below the Serial No.
SCREEN BURN ● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does not occur as far as displaying normal video playback motion images.
ENGLISH 3 Fuse POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries.
CONTROLS AND FEA TURES FRONT VIEW <Front Panel> T ally lamp Lights when the tally control signal is ON. Set the MAKE/ TRIGGER terminal’s tally control in the REMOTE (external control) terminal setup menu. For details, refer to Page 20. The lamp color can be set to red or green.
ENGLISH REAR/SIDE VIEW <Rear Panel> COLOR OFF button/lamp Press the COLOR OFF button. The button lights and the screen becomes monochrome. When the COLOR OFF button is pressed while lit, the light goes off and the normal screen is restored. Use this function to confirm the noise in the brightness signal or to confirm the white balance.
Video input/output terminals Input (IN) and output (OUT) terminals for component (colour difference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.
ENGLISH 䡵 SDI INPUT CARD (OPTIONAL: IF-C01SDG) AUDIO 2 AUDIO 1 OUT IN SWITCHED OUT SDI 1 SDI 2 IN IN 1 2 3 4 Output terminal for a selected component serial digital signal Output terminal for a selected digital signal (the input displayed on the screen).
8 CONTROLS AND FEA TURES (INPUT CARD: OPTIONAL) (cont'd) 䡵 HD SDI INPUT CARD (OPTIONAL: IF-C12HSDG) 䡵 Compatible signal formats: 720/60p, 1080/50i, 1080/60i, 1035/60i, 1080/24psF , EMBEDDED AUDIO Input and output terminals for HD SDI 1 component serial digital signals Input (IN) and output (OUT) terminals for HD serial digital signals.
ENGLISH PREP ARA TION 1. Turn of f the Multi-Format Monitor ’ s main power and unplug the power cable from the AC outlet. 2. Unscrew the screws and remove the slot cover from the slot (on the rear side of the monitor) in which you are going to install the card.
10 1. Attach the Power Cord Holder case to the AC inlet on the back of the monitor with 2 screws (provided). 2 Attach the Power Cord Holder cover to the AC power cord. 3. Connect the AC power cord to the AC inlet, and join the Power Cord Holder cover with the case.
ENGLISH BASIC MENU OPERA TIONS (MAIN MENU, SETUP MENU) 䡵 ABOUT MENU SCREENS This monitor features a MAIN MENU (main menu screen) and a SETUP MENU (setup menu screen). The MAIN MENU contains the functions normally used, and the SETUP MENU contains the settings required for initial setup.
12 HOW TO USE “MAIN MENU” 䡵 “ MAIN MENU ” ITEMS The following items appear in MAIN MENU. Items Functions Displays 1 APERTURE CONTROL Compensates the frequency characteristics of the input video signal. * 1 2 SLOT CONDITION Displays the status of the input cards installed in each of the input card slots.
ENGLISH 1. APERTURE CONTROL Compensates the frequency characteristics of the input video signal. Press the button to display the setting menu illustrated on the right. NOTE : APERTURE CONTROL is not displayed when the RGB signal is input. ● INPUT A/B corresponds to SLOT 1, INPUT C/D to SLOT 2, and INPUT E/F to SLOT 3.
14 Input Signal Format Standard Manual setting setting (MANUAL) NTSC, P AL, 480/60i, ITU601 480/60p, 576/50i, 575/50p ITU709 720/60p, 1080/50i, 1080/60i, ITU709 1035/60i, 1080/24psF <COLOR MATRIX> SELECT :MANUAL R-Y PHASE : 90 R/B GAIN :0.86 G-Y PHASE : 244 G/B GAIN :0.
ENGLISH HOW TO USE “SETUP MENU” 䡵 “ SETUP MENU ” ITEMS Items Functions 1 FUNCTION SETTING Displays the monitor ’s power-up time or the total usage time. 2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel.
16 HOW TO USE “SETUP MENU” (cont'd) <FUNCTION SETTING> COLOR SYSTEM :AUTO SYNC SELECT :AUTO RUSH DELAY TIME :STD. TALLY SELECT :GREEN REMOTE SYSTEM :MAKE EMBEDDED :1G HOUR METER X100h :000 EXIT: MENU ADJUST:- + SELECT: 䡵 ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS 1.
ENGLISH Item : CONTRAST Adjustment range : –20 ~ 00 ~ +20 Function : For approximate adjustment of the picture contrast. Before adjustment, set the CON- TRAST knob on the front panel to 0. Item : BRIGHT Adjustment range : –20 ~ 00 ~ +20 Function : For approximate adjustment of the picture brightness.
18 HOW TO USE “SETUP MENU” (cont'd) <DISTORTION ADJ.> PINCUSHION : 00 PIN.BALANCE : 00 PARALLELOGRAM : 00 TRAPEZOID : 00 ROTATION : 00 sub menu reset EXIT: MENU ADJUST:- + SELECT: 5. DISTORTION ADJ. Compensates the picture distortion. Press the button to display the setting menu illustrated on the right.
ENGLISH <STATUS DISPLAY> STATUS DISPLAY :ON 1080/1035 :1080 EXIT: MENU ADJUST:- + SELECT: Item : ST A TUS DISPLA Y Settings : ON/OFF Function : Makes the format name appear or disappear when signals are input and the signal status appear or disappear when the input signal is changed.
20 HOW TO USE EXTERNAL CONTROL 䡵 ABOUT EXTERNAL CONTROL The Multi-Format Monitor has two external control terminals. One is the MAKE/TRIGGER terminal, which allows the monitor to be controlled by the MAKE(make contact) or TRG. (trigger contact) method selected in the function setting.
ENGLISH 䡵 HOW T O USE THE RS-232C TERMINAL Y ou can control the monitor from your PC via the RS-232C terminal. For details on operating the monitor from the PC, consult your dealer or service centre for details. 1. Cable Prepare a straight cable with a D-sub connector (9-pin, female) and a D-sub connector (9-pin, male) 2.
22 TROUBLESHOOTING Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorised dealer or service centre for assistance.
ENGLISH Problems Irregular colour Wrong picture position, wrong picture size Front panel buttons and knobs do not function Points to be checked Is the monitor placed or moved close to a speaker or any.
24 䡵 SELF-CHECK INDICA TIONS When the screen goes blank, and one or more of the INPUT SELECT A through F buttons on the front control panel start blinking... This monitor has a self-check function, which allows it to detect malfunctions and alert you.
ENGLISH 440 377 285 375 380.4 372 206 336 95.7 496 VOLUME SLOT 1 A B DEGAUSS MENU MUTING SCREENS CHECK ASPECT AREA MARKER UNDER SCAN PULSE CROSS COLOR OFF SLOT 2 C D SLOT 3 POWER E F INPUT SELECT VOLU.
26 Usage Precautions ● The selected signal is output from the SWITCHED OUT terminal only when the monitor ’s power is turned on. ● The output signal from the SWITCHED OUT terminal is the one that is selected from the signals input to SDI 1 / HD SDI 1 or SDI 2 / HD SDI 2.
ENGLISH SPECIFICA TIONS (INPUT CARD: OPTIONAL) 䡵 IF-C01COMG: COMPONENT/RGB INPUT CARD T ype : Component/RGB input card for Multi-Format Monitor Inputs/Outputs : Component (Y , P B /B-Y , P R /R-Y) or RGB: 1 line, BNC connector x 6 (Y : 1 V (p-p), 75 Ω /P B , B-Y , P R , R-Y , R, G, B: 0.
䡵 IF-C01HSDG: HD SDI INPUT CARD T ype : HD SDI input card for Multi-Format Monitor Inputs/Outputs : Digital input (HD SDI 1/HD SDI 2): 2 lines, BNC connector x 2 (0.8 V (p-p), 75 Ω ) Digital output (SWITCHED OUT): 1 line, BNC connector x 1 (0.8 V (p-p), 75 Ω ) Audio signal: 1 line (monaural), RCA pin x 2 (0.
LCT1002-001B(EN) 02.1.29, 6:24 PM 27.
© 2002 VICTOR COMP ANY OF JAP AN, LIMITED Printed in Japan 0202-Y-U-VP VICTOR COMPANY OF JAPAN, LIMITED DT -V1900CG MUL TI-FORMA T MONIT OR LCT1116-001A(EN) 02.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté JVC DT-V1900CG c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du JVC DT-V1900CG - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation JVC DT-V1900CG, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le JVC DT-V1900CG va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le JVC DT-V1900CG, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du JVC DT-V1900CG.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le JVC DT-V1900CG. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei JVC DT-V1900CG ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
