Manuel d'utilisation / d'entretien du produit M-series M7i du fabricant Juniper
Aller à la page of 23
M7i Internet Router Quick Start 30 April 2007 Part Number: 530-017640-01 Revision 2 This document describes how to install the M7i Internet router. Contents Quick Start Description ......................................................................
Compliance Statements for NEBS ..................................................................17 Compliance Statements for EMC Requirements ............................................17 Canada ......................................................
Quick Start Description This Quick Start contains information you need to install and configure the router quickly. For complete installation instructions, see the M7i Internet Router Hardware Guide at http://www.juniper.net/techpubs/hardware/ . WARNING: This Quick Start contains a summary of safety warnings in “ Safety Warnings ” on page 15.
floor-to-ceiling rack. If you do so, the rack must be capable of supporting a combined weight of over 766 lb (347 kg). ■ The rack rails must be spaced widely enough to accommodate the router chassis's external dimensions: 3.5 in. (8.9 cm) high, 18.
Figure 1: Rack Clearances and Router Dimensions Tools Required ■ Phillips (+) screwdriver, numbers 1 and 2 ■ Electrostatic discharge wrist strap ■ Antistatic mat ■ Blank panels to cover any sl.
Step 2: Prepare for Front or Center Mounting The cable management system organizes and supports the PIC cables to prevent damage. The mounting brackets are shipped installed in the front-mounting position, but must be removed to install the cable management system.
Step 3: Install the Router 1. Have one person grasp each side of the router, lift the router, and position it in the rack. See Figure 4 on page 8. 2. Align the bottom hole in each mounting bracket with a hole in each rack rail, making sure the chassis is level.
Figure 4: Lift the Router into the Rack Step 4: Connect External Devices and PIC Cables To connect external devices and PIC or FIC cables, perform the following procedures: ■ Connect a Management Co.
Figure 5: Connect External Devices and PIC Cables to Router Connect a Management Console or Auxiliary Device 1. Turn off the power to the console or auxiliary device. 2. Plug the female end of the RS-232 serial connector into the CONSOLE or AUX/MODEM port.
CAUTION: To prevent damage to fiber-optic transceivers and fiber-optic cables, observe the following precautions: ■ Do not leave a fiber-optic transceiver uncovered except when inserting or removing cable. The safety plug keeps the port clean and prevents accidental exposure to laser light.
3. Verify that the switch on each power supply faceplate is in the OFF ( O ) position. 4. For each power supply: a. Insert the appliance coupler end of a power cord into the appliance inlet on a power supply faceplate. b. Insert the plug into an AC power source receptacle.
11. Verify that the power cables are not touching or blocking access to router components, and that they do not drape where people could trip on them. 12. Switch on the external circuit breakers to provide voltage to the DC power source cable leads. Figure 6: Connect the Power Cables to a DC Router Step 6: Power On the Router 1.
7. Verify that the OUPUT OK LED lights steadily. If the LED does not light after 60 seconds, repeat Steps 3 through 6. If necessary, reinstall the AC power cord or DC power cables. 8. For routers with two power supplies, repeat Steps 3 through 7 for the second power supply.
root@# set system name-server address 10. Set the root authentication password by entering either a clear-text password, an encrypted password, or an ssh public key string (DSA or RSA).
13. Optionally, configure additional properties by adding the necessary configuration statements. Then commit the changes to activate them on the router. [edit] root@host# commit 14. When you have finished configuring the router, exit configuration mode.
■ When installing the router, do not use a ramp inclined at more than 10 degrees. ■ Manually installing the router requires two people to lift. To prevent injury, keep your back straight and lift with your legs, not your back. Do not attempt to lift the chassis by the power supply handles.
Compliance Statements for NEBS This product complies with the following standards: ■ GR-63-Core: NEBS, Physical Protection ■ GR-1089-Core: EMC and Electrical Safety for Network Telecommunications .
Declaration of Conformity 18 ■ Compliance Statements for EMC Requirements M7i Internet Router Quick Start.
List of Technical Publications Table 1 on page 19 lists the software and hardware guides and release notes for Juniper Networks J-series, M-series, MX-series, and T-series routing platforms and describes the contents of each document. Table 2 on page 22 lists the books included in the Network Operations Guide series.
Table 1: Technical Documentation for Supported Routing Platforms (continued) Description Book Provides an overview of secure Common Criteria and JUNOS-FIPS protocols for the JUNOS Internet software and describes how to install and configure secure Common Criteria and JUNOS-FIPS on a routing platform.
Table 1: Technical Documentation for Supported Routing Platforms (continued) Description Book JUNOS API and Scripting Documentation Describes how to use the JUNOScript application programming interface (API) to monitor and configure Juniper Networks routing platforms.
Table 1: Technical Documentation for Supported Routing Platforms (continued) Description Book Shows how to manage users and operations, monitor network performance, upgrade software, and diagnose common problems on J-series Services Routers.
Requesting Support For technical support, open a support case with the Case Manager link at http://www.juniper.net/support/ or call 1-888-314-JTAC (from the United States, Canada, or Mexico) or 1-408-745-9500 (from elsewhere). Revision History 30 April 2007 — 530-017640-01.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Juniper Juniper M-series M7i c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Juniper Juniper M-series M7i - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Juniper Juniper M-series M7i, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Juniper Juniper M-series M7i va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Juniper Juniper M-series M7i, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Juniper Juniper M-series M7i.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Juniper Juniper M-series M7i. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Juniper Juniper M-series M7i ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
