Manuel d'utilisation / d'entretien du produit GT 2125 du fabricant Jonsered
Aller à la page of 32
GT 2125 GC 2125 Operator’ s manual (EP A) Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Clear ing saws , brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Jonsered has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment.
4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es should be wor n when necessar y , e.g., when fi tting cutting attachments. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection.
English – 5 SAFETY INSTR UCTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to reduce vibration and mak e operation easier . Use of incorrectly wound cord or an incorrect cutting attachment increases the le vel of vibr ation.
6 – English SAFETY INSTR UCTIONS Chec king, maintaining and servicing the machine ′′ ′ ′ s safety equipment Throttle loc k • Make sure the throttle control is loc ked at the idle setting when the throttle lock is released. • Press the throttle lock and mak e sure it retur ns to its original position when you release it.
English – 7 SAFETY INSTR UCTIONS • Regularly check that the muf fl er is securely attached to the machine. • If the muf fl er on y our machine is fi tted with a spark arrestor mesh then it should be cleaned regularly . A bloc ked mesh causes the engine to ov erheat, which can lead to serious damage.
8 – English SAFETY INSTR UCTIONS Cutting equipment Sharpening grass cutters and grass blades • See the cutting attachment packaging f or correct shar pening instructions. • Shar pen blades and cutters using a single-cut fl at fi le . • Shar pen all edges equally to maintain the balance of the blade .
English – 9 SAFETY INSTR UCTIONS General safety precautions Starting • The complete clutch cov er and shaft must be fi tted before the machine is star ted, otherwise the clutch can come loose and cause personal injur y . • Ne ver start the machine indoors.
10 – English SAFETY INSTR UCTIONS • The transpor t guard must alwa ys be fi tted to the cutting attachment when the machine is being transpor ted or in storage. General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine .
English – 11 SAFETY INSTR UCTIONS Grass trimming using a trimmer head and plastic blades T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Nev er press the cord into the area to be cut.
12 – English WHA T IS WHA T? What is what on the trimmer? 30 1 T rimmer head 2 Grease fi ller cap , be vel gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 S.
English – 13 ASSEMBL Y Fitting the loop handle (GT 2125) • P osition the handle on the shaft. Note that the handle must be mounted below the arro w on the shaft. • Fit the screw , secur ing plate and wing nut as shown in the diagram. • Tighten the wing nut.
14 – English ASSEMBL Y Fitting the trimmer guar d and A uto 32 trimmer head (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fi tting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft.
English – 15 ASSEMBL Y Fitting other guar ds and cutting attachments (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fi tting on the shaft and secure with the bolt (L).
16 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-stroke engine and must alwa ys been run using a mixture of gasoline and two-strok e engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
English – 17 FUEL HANDLING Fueling • Clean the area around the fuel cap . Contamination in the tank can cause operating prob lems. • Ensure that the fuel is well mix ed by shaking the container bef ore fi lling the tank.
18 – English ST AR TING AND ST OPPING Chec k before starting • Check that the support fl ange is not crack ed due to fatigue or due to being tightened too much. Discard the suppor t fl ange if it is crac ked. • Ensure the locking n ut has not lost its captive f orce.
English – 19 ST AR TING AND ST OPPING some resistance (the star ter pawls grip), now quic kly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine star ts.
20 – English MAINTENANCE Carb uretor Y our Jonsered product has been designed and manuf actured to speci fi cations that reduce harmful exhaust fumes.
English – 21 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T , if it is necessar y to readjust. First tur n the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops.
22 – English MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder .
English – 23 MAINTENANCE Spark plug The spark plug condition is in fl uenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air fi lter . These f actors cause deposits on the spark plug electrodes, which ma y result in operating problems and starting dif fi culties.
24 – English TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le vel is calculated as the time-weighted energy total f or noise pressure le vels under v ar ious working conditions with the follo wing time distr ibution: 1/2 idle and 1/2 max.
English – 25 TECHNICAL D A T A Appro ved accessories T ype Cutting attachment guar d, Art. no. GT 2125 Blade shaft thread 3/8 R T rimmer head T ap-N-Go VII (R) 530 05 60-57 GC 2125 Arbor shaft threa.
26 – English FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to e xplain the emissions control system warranty on y our 2001 and later small nonroad engine.
1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6".
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
´®z*x}3¶5U¨ ´®z*x}3¶5U¨ T ap-N-Go 35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
1 Auto 32 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " 15 cm 15 cm.
´®z*x}3¶5U¨ 2004-06-14 ´®z*x}3¶5U¨ 1088931-95.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Jonsered GT 2125 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Jonsered GT 2125 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Jonsered GT 2125, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Jonsered GT 2125 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Jonsered GT 2125, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Jonsered GT 2125.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Jonsered GT 2125. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Jonsered GT 2125 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
