Manuel d'utilisation / d'entretien du produit JWSS-10CS du fabricant Jet Tools
Aller à la page of 44
Operating Instructions and Parts Manual SuperSaw Model: JWSS-10CS WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-708781 Ph.: 800-274-6848 Revision B 07/06 www.
2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the Unit ed States can give you quick service.
3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents ........................................................
4 Troubleshooting ................................................................................................................ .......................... 28 Parts ....................................................................................
5 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
6 xxxxxxxxxxxxx xxxxxxxxxxxxxxx xxxxxxxxxxxxxxx xxxxxxxxxxxxxxx xxx 21. Provide for adequate space surroundi ng work area and non-glare, overhead light ing. 22. Keep the floor around the machi ne clean and free of scrap materia l, oil and grease. 23. Keep visitors a safe distance from the work area.
7 The most common accidents among ta ble saw users, accor ding to statistics, ca n be linked to kickback, the high-speed expulsion of materia l from the table that can strike the operator. Kickback can also result in operator’s hands being pulled into the blade.
8 Read and understand the entire contents of this manual before attempting assembly or operation ! Failure to comply may cause serious injury Contents of the Shipping Containers 1 Table saw 1 Right Wi.
9 Left Wing Extension Box (optional accessory) 1 Left Wing Extension w/Miter Slot 1 Miter Gauge 1 Miter Gauge Bar 1 Miter Gauge Handle 1 Miter Gauge Fence Hardware Bag 4 Socket Head Cap Screws M10x90 .
10 Assembly Unpacking and Clean-Up Do not connect th e table saw to the power source until assembly has been completed! Failure to comply may cause serious injury! • Tool: 12mm Wrench 1. Remove all content s from the shipping container. Do not discard any shipping material until the saw is set up and running satisfactorily.
11 Mounting Rails Hardware: Front Rail, Rear Rail, (4) M8x16 Socket Head Cap S crews, (4) M8 Flat Washers, (4) Lock Washers, (2) 1/4-20 x 1-1/2 Hex Cap Screws, (4) 1/4” Flat Washers, (2) 1/4” Lock Washers, (2) 1/4” hex nuts. Tools: 6 mm hex wrench, two 13mm wrenches Refer to Figures 4 and 5.
12 Miter Gauge for Left Extension Wing Hardware: Miter Gauge Tools: Cross Point Screw Driver, Square 1. Change the angle on the miter gauge by loosening handle (E, Fig. 7) and turning the fence (F, Fig. 7) to desi red angle. To move gauge beyond index stops of 45 ° and 90 ° , flip back the stop (G, Fig.
13 The support plate underneath the sli ding table (Figure 10) has an inn er tab (A) and an outer tab (B). When placing the table onto the leveling bracket (D, Fig. 8), the leveling bracket must be positioned between the inne r and outer tabs and the slots in the tabs (C, Fig.
14 Sliding Table Miter Gauge Hardware: Miter Gauge, Fen ce, (2) Handles, Stop, Fence Bar, Indicator Bar, Bushing, Bracket Clamp Assembly & (2) Handles Tools: 2.5mm Hex Wrench 1. Slide the miter gauge fence (B, Fig. 13) into the bar (A, Fig. 13) and attach to the miter gauge body (C, Fig.
15 Mounting the Switch Assembly Hardware: (2) 1/4x1/2 Hex Cap Screws, (2) 1/4 Lock Washe rs, (2) 1/4 Flat Washers. Tool: 4mm Hex Wrench Referring to Figure 15: Mount the switch assembly (A) to the bottom side of the front rail (B) with two butto n head cap screws (C) a nd two washers (D ).
16 table, until it is level with the saw table (Figure 17). As one part of the edge become s level with the table, tighten the clamp on that side. Then move to the other side an d repeat, until the full length of the edge is level with the saw table. Lay a straight edge acro ss both extension table and saw table to ensure proper leveling.
17 slot (A. Fig. 21), orient the guide tube (B) with respect to the rail (C) as shown in Figure 21. If your left table wing is the sliding table type (D, Fig. 22), mount the gui de tube (F) so it lines up with the left edge on the angle iron portion of the rail (E).
18 4. Raise or lower two nylon adjustment scre ws (A, Fig. 27) the same number of turns until the space between the bottom of the fence and the table is the same. Care m ust be taken to raise or lower the fence on each side equall y or the fence may not be 90 ° to the table after the height adjustment is performed.
19 Installing the Blade When installing or changing saw blade, always disconnect sa w from power source! Failure to com ply may cause serious injury! Hardware: Blade Tools: Arbor Wrench, Scrap Piece of Wood 1. Raise the blade arbor and make sure th e arbor is at the zero degree position.
20 Blade Guard Assembly Hardware: Blade Guard Assembly, Splitter Guard Assembly Tools: 12mm Wrench, 17mm Wrench or Adjustable Wrench, 3mm Hex Wrench 1. With a 3mm hex wren ch, loosen two set screws (G, Fig. 34) on the splitter guard assembly and remove the bracket.
21 Hooks for Miter Gauge and Fence Hardware: (2) Miter Gauge Ho oks, (2) Fence Hooks, (4) M8x16 Ca rriage Bolts, (4) M8 Fl at Washers, (4) M8 Loc k Washers & (4) He x Nuts Tool: 13mm Wrench 1. Mount the two fence hooks (A, Fig. 38) with two M8x16 carriage bolt s, two M8 flat washers, two M8 lock washers and two M8 hex nuts.
22 Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or br eakdown, grounding provides a path of least resistance fo r electric current to re duce the risk of ele ctric shock.
23 Adjustments Blade Alignment Tools: 8mm Hex Wrench, Combinatio n Square & Marker Blade alignment with the miter sl ot is adjusted at the factory. After a period of use, or after moving the saw to another location, the blade may no longer be aligned properly.
24 Adjusting 45 ° and 90 ° Positive Stops The stops have been adju sted at the factory. After a period of use, or, after moving the saw to another location, the stops may n o longer be set properly. To check and adjust the stops: Tool: 12mm Wrench, Combination Square 1.
25 Wear Adjustment in Raising Mechanism As the worm gear wears with time you may notice a little play in the handwhe el. To adjust for wear in the raising mechani sm: 1.
26 Changing Poly V-Belt Make all machine adjustments or m aintenance with the machine unplugged from the power source. Failure to comply may cause serious injury! 1. Disconnect the machine from the power source, unplug. 2. Lower the blade to its lowest point and tilt to 45°.
27 Maintenance General Maintenance Cabinet and Motor : Keep the inside of the cabinet clear of sa wdust and wood chips. Vacuum out the inside of the cabinet an d blow out the inside with an air hose. Make sure the motor fan and fan cover are also kept clear of sawdust.
28 Troubleshooting Trouble Possible Cause Solution Saw stops or will not start 1. Overload tripped 2. Saw unplugged from wall or moto r 3. Fuse blown or circuit b reaker tripped 4. Cord damaged 5. Starting Capacitor is bad 6. Centrifugal S witch bad or out of adjustment 1.
29 Parts XACTA Fence II Homeshop 30/52 Fence Assembl y Index No. Part No. Description Size Qty 1 ............... HF2-101 ................... Left Side Plate ...................................................... ................ .................... 1 2 .
30 Cabinet Assembly Index No. Part No. Description Size Qty 1 ............... JWSS10CS-01 ......... Cabinet ................................................................. ................... ................. 1 2 ............... JW SS10CS-02 ......
31 Guard Assembly Index No. Part No. Description Size Qty 1 ............... 200321 ..................... Support Arm ......................................................... ................ .................... 1 2 ............... TS-2342061 .......
32 Table Assembly Index No. Part No. Description Size Qty 1 ............... TS-1550061 ............. Flat Was her .......................................................... M8 ................. ............ 13 2 ............... TS-1551061 ............
33 Table Assembly Index No. Part No. Description Size Qty 58f ............ 200353 ..................... Switch Bracket ..................................................... .................. .................. 1 58g ........... 200354 ...............
34 Table Assembly.
35 Sliding Table Assembly Index No. Part No. Description Size Qty 1 ............... 200364 ..................... Sliding Table ........................................................ ............... ..................... 1 2 ............... 200411 ..
36 Sliding Table Assembly Index No. Part No. Description Size Qty 57 ............. 200374 ..................... 90° Adjust able Plate ............................................. 0.02” ............... ............. 2 58 ............. NH061000 ....
37 Sliding Table Assembly.
38 Rail Assembly Index No. Part No. Description Size Qty ................. 708783Z ................... Rail Assembly - Standard (30”) ........................... .......................... .......... 1 ................. 708782Z ................... Rail Assembly - Long Table (52”) .
39 Rail Assembly.
40 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 1 ............... 200310 ..................... Rear Tru nnion Bracket ......................................... ...................... .............. 1 2 ............... TS-1550061 .
41 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 51 ............. 200404 ..................... Handle .................................................................. .................................... 2 52 ............. 150045 .
42 Motor & Trunnion Assembly.
43 Wiring Diagrams 115V Wiring.
44 230V Wiring WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.co m.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Jet Tools JWSS-10CS c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Jet Tools JWSS-10CS - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Jet Tools JWSS-10CS, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Jet Tools JWSS-10CS va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Jet Tools JWSS-10CS, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Jet Tools JWSS-10CS.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Jet Tools JWSS-10CS. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Jet Tools JWSS-10CS ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
