Manuel d'utilisation / d'entretien du produit Wrangler Unlimited (2013) du fabricant Jeep
Aller à la page of 655
W r angler Includes W r angler Unlimited Chrysler Group LLC O WNER’S MANU AL 2013 W r angler 13JK72-126-AB Second Edition Printed in U.S.A. 2013 I n f o r m a t i o n P r o v i d e d b y :.
VEHICLES SOLD IN CANADA With respect to any V ehicles Sold in Canada, the name Chrysler Gr oup LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor e. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................ 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 INTRODUCTION ........................ 4 䡵 ROLLOVER W ARNING .................... 5 䡵 HOW TO USE THIS MANUAL .............. 6 䡵 W ARNINGS AND CAUTIONS .............. 8 䡵 VEHICLE IDENTIFICA TION NUMBER ........ 8 䡵 VEHICLE MODIFICA TIONS/AL TERA TIONS .
INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle.
This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by W arranty Information, and various customer-oriented documents.
Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury . Drive carefully .
1 INTRODUCTION 7 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This Owners Manual contains W ARNINGS against op- erating procedures that could result in a collision or bodily injury . It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
NOTE: It is illegal to remove or alter the VIN plate. VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously af fect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A WORD ABOUT YOUR KEYS ............. 1 4 ▫ Ignition Key Removal ................... 1 4 ▫ Key-In-Ignition Reminder ................ 1 6 䡵 SENTR Y KEY 威 ......................... 1 6 ▫ Replacement Keys .
▫ Programming Additional T ransmitters ........ 2 6 ▫ General Information .................... 2 6 ▫ T ransmitter Battery Replacement ........... 2 7 䡵 REMOTE ST AR TING SYSTEM — IF EQUIPPED .......................... 2 8 ▫ How T o Use Remote Start .
▫ Adjustable Upper Shoulder Belt Anchorage . . .55 ▫ Seat Belts In Passenger Seating Positions ...... 5 6 ▫ Automatic Locking Retractor Mode (ALR) — If Equipped ........................ 5 7 ▫ Energy Management Feature .............. 5 8 ▫ Seat Belt Pretensioners .
A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number . The key code can also be obtained by your authorized dealer from your vehicle invoice.
3. Push the ignition key inward. 4. T urn the ignition key to the LOCK position, and remove the key . W ARNING! • Before exiting a vehicle, always apply the parking brake, shift the transmission into P ARK, and re- move the Key Fob from the ignition.
Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition sounds a signal to remind you to remove the key . NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.
CAUTION! The Sentry Key 威 Immobilizer system is not compat- ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
Customer Key Programming If you have two valid Sentry Keys 威 , you can pr ogram new Sentry Keys 威 to the system by performing the following procedure: 1. Cut the additional Sentry Key 威 T ransponder blank(s) to match the ignition switch lock cylinder key code.
NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory . This will pr event the lost key from starting your vehicle. The remaining keys must then be repr ogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be repr o- grammed.
Rearming The System If something triggers the alarm, and no action is taken to disarm it, the V ehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the V ehicle Security Alarm will rearm itself.
the alarm will sound. If this occurs, press the UNLOCK button on the RKE transmitter to disarm the V ehicle Security Alarm. Y ou may also accidentally disarm the V ehicle Security Alarm by unlocking the driver’s door with the key and then locking it.
REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors, swing gate, and activate the Panic Alarm from a maximum distance of 66 ft (20 m) using a Remote Keyless Entry (RKE) transmitter . The RKE transmitter does not need to be pointed at the vehicle to activate the system.
• For vehicles not equipped with the EVIC, the Remote Unlock feature can be enabled or disabled by perform- ing the following steps: 1. Press and hold the LOCK button on a programmed RKE transmitter .
Sound Horn On Lock This featur e will cause the horn to chirp when the doors are locked with the RKE transmitter . This featur e can be turned on or turned off.
T o T urn Off Flash Lights With Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmit- ter .
Programming Additional T ransmitters Refer to Sentry Key 威 “Customer Key Programming.” If you do not have a programmed RKE transmitter , contact your authorized dealer for details. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada.
T ransmitter Battery Replacement The recommended replacement battery is CR2032. NOTE: Perchlorate Material – special handling may ap- ply . See www .dtsc.ca.gov/hazardouswaste/per chlorate 1. W ith the RKE transmitter buttons facing down, use a flat blade scr ewdriver to pry the two halves of the RKE transmitter apart.
REMOTE ST ARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security .
W ARNING! (Continued) • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
• The engine can be started two consecutive times (two 15-minute cycles) with the RKE transmitter . However , the ignition switch must be cycled to the ON/RUN position before you can repeat the start sequence for a third cycle.
DOORS CAUTION! Careless handling and storage of the removable door panels may damage the seals, causing water to leak into the vehicle’s interior . Upper Half Door Window Removal — If Equipped Grasp the half door window and pull upward. Upper Half Door Window Installation — If Equipped 1.
Front Door Removal W ARNING! Do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only . 1. Roll down the glass window to prevent any damage.
tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 4. Unhook the door strap from the body hook. Be careful not to allow the door to swing fully open as the mirror may damage the paint. 5. W ith the door open, lift the door to clear the hinge pins from their hinges and remove the door .
Rear Door Removal (Four-Door Models) W ARNING! Do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only . 1. Roll down the glass window to prevent any damage.
5. Unplug the wiring harness connector . NOTE: If the red latch on the connector is locked, push the r ed latch to the right until you can only see the latch on one end (right) of the connector . This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected.
NOTE: Doors ar e heavy; use caution when removing them. T o reinstall the door(s), perform the previous steps in the opposite order . DOOR LOCKS Manual Door Locks All doors are equipped with an interior rocker -type door lock lever .
NOTE: The ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, glove compartment, and console storage. W ARNING! • For personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when you park and leave the vehicle.
Power Door Locks — If Equipped The power door lock switch is located on each front door panel. Press the switch forward to lock the doors, and rearwar d to unlock the doors. W ARNING! • For personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when you park and leave the vehicle.
Automatic Door Locks — If Equipped When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock featur e can be enabled or disabled by your authorized dealer . Please see your authorized dealer for service.
Child-Protection Door Lock System — Rear Doors T o provide a safer environment for small children riding in the rear seats, the rear doors are equipped with Child-Protection Door Lock system. T o Engage Or Disengage The Child-Protection Door Lock System 1.
NOTE: For emergency exit with the system engaged, move the r ocker lever r earward (unlocked position), roll down the window and open the door with the outside door handle. WINDOWS Power Windows — If Equipped The power window switches are located on the instru- ment panel below the radio.
Four-Door Models The lower left switch controls the left rear passenger window , and the lower right switch controls the right rear passenger window . Auto-Down Both the driver and front passenger window switches have an “Auto-Down” feature. Pr ess the window switch past the first detent, release, and the window will go down automatically .
Rear Power Windows — Four-Door Models The rear passenger window switches are located on the back of the center floor console. Press the switch down- ward to open the window and upward to close the window . Wind Buffeting W ind buffeting can be described as the per ception of pressur e on the ears or a helicopter-type sound in the ears.
REAR SWING GA TE The rear swing gate can be unlocked by using the key , Remote Keyless Entry (RKE) transmitter , or by activating the power door lock switches located on the fr ont doors.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: • Three-point lap and shoulder belts for the driver and all passengers • Advanced Front A.
NOTE: The Advanced Fr ont Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1.
Y ou should read the instructions provided with your child r estraint to make sure that you are using it properly . 2. All occupants should always wear their lap and shoulder belts properly . 3. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front Air Bags room to inflate.
W ARNING! (Continued) • In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat and next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
W ARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. Y ou are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together .
W ARNING! • A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug.
Rear Center Lap/Shoulder Belt Retractor Lockout — Four-Door Models Only This feature is designed to lock the retractor whenever the 60% rear seatback is not fully latched. This prevents someone fr om wearing the rear center lap/shoulder belt when the rear seatback is not fully latched.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
W ARNING! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
If the passenger seating position is equipped with an ALR and is being used for normal usage: Only pull the belt webbing out far enough to comfortably wrap ar ound the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a ratcheting sound as the belt retracts.
How T o Disengage The Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it to r etract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode.
W ARNING! (Continued) • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack fr om the seat belt in the event of a collision.
The BeltAlert 威 warning sequence begins after the vehicle speed is over 5 mph (8 km/h), by blinking the Seat Belt Reminder Light and sounding an intermittent chime. Once the sequence starts, it will continue for the entire duration or until the respective seatbelts are fastened.
Seat Belts And Pregnant Women W e recommend that pregnant women use seat belts throughout their pregnancy . Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug acr oss the hips as possible.
Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the steering wheel.
NOTE: The Driver and Passenger Advanced Front Air Bags are certified to new Federal regulations. The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have differ ent rates of inflation that are based on several factors, including the severity and type of collision.
Air Bag System Components Y our vehicle may be equipped with the following air bag system components: • Occupant Restraint Controller (ORC) • Air Bag W arning Light • Steering Wheel and Column .
W ARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually . Y ou may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating.
Supplemental Seat-Mounted Side Air Bags (SAB) — If Equipped Supplemental Seat-Mounted Side Air Bags (SAB) may provide enhanced protection to help protect an occupant during a side impact. The SAB is marked with an air bag label sewn into the outboard side of the front seats.
Along with seat belts and pretensioners, Advanced Front Air Bags work with the Supplemental Driver Side Knee Air Bag and the passenger side knee bolster to provide improved protection for the driver and front passenger . Side air bags also work with seat belts to improve occupant protection.
The side air bags will not deploy in all side collisions. Side air bag deployment will depend on the severity and type of collision. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed.
W ARNING! Ignoring the Air Bag W arning Light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the .
Supplemental Seat-Mounted Side Air Bags (SAB) Inflator Units — If Equipped The Supplemental Seat-Mounted Side Air Bags Inflator Units (if equipped) are designed to activate only in certain side collisions.
• T urn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlock the doors automatically . In or der to r eset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from IGN ON to IGN OFF .
• As the air bags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat.
W ARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. T ake your vehicle to an authorized dealer for any air bag system service.
W ARNING! (Continued) • It is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. Air Bag W arning Light Y ou will want to have the air bags ready to inflate for your protection in a collision.
Event Data Recorder (EDR) This vehicle is equipped with an event data recor der (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per- formed.
Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, r equires that small children ride in proper restraint systems. This is the law , and you can be prosecuted for ignoring it.
Summary Of Recommendations For Restraining Children In V ehicles Child Size, Height, W eight or Age Recommended T ype of Child Restraint Infants and T oddlers Children who ar e two years old or younge.
Infants And Child Restraints Safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. T wo types of child restraints can be used rearward-facing: infant carriers and convertible child seats.
Older Children And Child Restraints Children who are two years old or who have outgrown their rear -facing convertible child seat can ride forward- facing in the vehicle.
Children T oo Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
Recommendations For Attaching Child Restraints Restraint T ype Combined W eight of the Child + Child Restraint Use any attachment method shown with an “X” Below LA TCH – Lower Anchors Only Seat Belt Only LA TCH – Lower Anchors + T op T ether Anchor Seat Belt + T op T ether Anchor Rear-Facing Child Restraint Up to 65 lbs (29.
Lower Anchors and T ethers for Children (LA TCH) Restraint System Y our vehicle is equipped with the child restraint anchor- age system called LA TCH, which stands for Lower Anchors and T ethers for CHildren. The LA TCH system has thr ee vehicle anchor points for installing LA TCH- equipped child seats.
LA TCH Positions For Installing Child Restraints In This V ehicle Latch Positions (T wo-Door Models) Lower Anchorage Symbol 2 anchorages per seating position T op T ether Anchorage Symbol Latch Positi.
What is the weight limit (child’s weight + weight of the child restraint) for using the LA TCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Use the LA TCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.
Can two child restraints be attached using a common lower LA TCH anchorage? No Never “share” a LA TCH anchorage with two or more child restraints. If the center position does not have dedicated LA.
Locating The LA TCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Locating The LA TCH Anchorages In addition, there are tether strap anchors lo- cated behind each r ear seatback, near to the floor . Latch Anchorages (Four-Door Models) T ether Strap Mounting (T wo-Do.
LA TCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear -facing infant r estraints will also be equipped with a tether strap.
T o Install A LA TCH-compatible Child Restraint 1. If the selected seating position has a Switchable Auto- matic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below . See the section “Installing Child Restraints Using the V ehicle Seat Belt” to check what type of seat belt each seating position has.
How T o Stow An Unused ALR Seatbelt When using the LA TCH attaching system to install a child r estraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seatbelt retractor .
Installing Child Restraints Using The V ehicle Seat Belt The seat belts in the passenger seating positions ar e equipped with either a Switchable Automatic Locking Retractor (ALR) or a cinching latch plate or both.
Lap/Shoulder Belt Systems for Installing Child Restraints in this V ehicle T wo-Door Models Four-Door Models 92 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
What is the weight limit (child’s weight + weight of the child restraint) for using the T ether Anchor with the seat belt to attach a forward facing child restraint? W eight limit of the Child Restr.
Installing A Child Restraint with a Switchable Automatic Locking Retractor (ALR) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit.
9. T est that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally , and pull it tight if necessary .
Any seat belt system will loosen with time, so check the belt occasionally , and pull it tight if necessary . If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt.
3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer ’s instructions.
W ARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap.
For the r ecommended viscosity and quality grades, refer to “Maintenance Procedur es” in “Maintaining Y our V ehi- cle”. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays, and loose parts.
Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that ar e firmly secur ed so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.
Periodic Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tir es for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS ............................ 1 1 1 ▫ Inside Day/Night Mirror ................ 1 1 1 ▫ Outside Mirrors ...................... 1 1 2 ▫ Power Mirrors — If Equipped ............ 1 1 3 ▫ Heated Mirrors — If Equipped .
▫ Delete/Erase “All” Uconnect™ Phonebook Entries ............................ .124 ▫ List All Names in the Uconnect™ Phonebook . .125 ▫ Phone Call Features ................... .125 ▫ Uconnect™ Phone Features ............. .128 ▫ Advanced Phone Connectivity .
▫ Replacing The Rear Seat — T wo-Door Models .................. .164 ▫ 60/40 Split Folding Rear Seat — Four-Door Models ........................... .164 䡵 TO OPEN AND CLOSE THE HOOD ........ .166 䡵 LIGHTS ............................ .167 ▫ Multifunction Lever .
▫ T o Set A Desired Speed ................ .179 ▫ T o Deactivate ....................... .180 ▫ T o Resume Speed .................... .180 ▫ T o V ary The Speed Setting .............. .180 ▫ T o Accelerate For Passing ............... .181 䡵 ELECTRICAL POWER OUTLET .
▫ Front Panel(s) Installation W ith Rear Hard T op Removed ....................... .210 ▫ Rear Hard T op Removal ............... .210 ▫ Rear Hard T op Installation .............. .213 䡵 DOOR FRAME ........................ .214 ▫ Door Frame Removal .
䡵 FOLDING WINDSHIELD ................ .286 ▫ Lowering The W indshield And Removing Side Bars .......................... .288 ▫ Raising The W indshield And Replacing Side Bars .......................... .291 䡵 REAR WINDOW FEA TURES — HARD TOP ONL Y .
MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror . Adjust the mirror to center on the view through the rear window . Headlight glar e can be reduced by moving the small control lever under the mirr or to the night position (lever flipped toward the rear of vehicle).
Outside Mirrors T o receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror . W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
Power Mirrors — If Equipped The power mirror switch is located on the center of the instrument panel, below the climate controls. A rotary knob selects the left mirror , right mirror or off position. After selecting a mirr or , move the knob in the same direction you want the mirror to move.
V anity Mirrors V anity mirrors are located on the sun visors. T o use the mirrors, rotate the sun visor down and swing the mirror cover upward. Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system.
For Uconnect™ customer support, visit the following websites: • www .chrysler .com/uconnect • www .dodge.com/uconnect • www .jeep.com/uconnect • or call 1–877–855–8400 Uconnect™ Phon.
Uconnect™ Phone Button The radio or steering wheel controls (if equipped) will contain the two control buttons (Uconnect™ Phone button and V oice Command button) that will enable you to access the system. When you press the button you will hear the word Uconnect™ followed by a BEEP .
Operation V oice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structure. V oice commands are required after most Uconnect™ Phone prompts. Y ou will be prompted for a specific command and then guided through the available options.
Help Command If you need assistance at any prompt, or if you want to know your options at any pr ompt, say “Help” following the beep. The Uconnect™ Phone will play all the options at any prompt if you ask for help. T o activate the Uconnect™ Phone from idle, simply pr ess the button and follow the audible pr ompts for directions.
• Y ou will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your mobile phone. Y ou can enter any four-digit PIN. Y ou will not need to remember this PIN after the initial pairing process.
Call by Saying a Name • Press the button to begin. • After the “Ready” prompt and the following beep, say “Call”. • The system will prompt you to say the name of the person you want to call. • After the “Ready” prompt and the following beep, say the name of the person you want to call.
After you are finished adding an entry into the phone- book, you will be given the opportunity to add mor e phone numbers to the current entry or to return to the main menu. The Uconnect™ Phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
• Only the phonebook of the currently connected mobile phone is accessible. • Only the mobile phone’s phonebook is downloaded. SIM card phonebook is not part of the Mobile phonebook. • This downloaded phonebook cannot be edited or deleted on the Uconnect™ Phone.
Edit Uconnect™ Phonebook Entries NOTE: • Editing names in the phonebook is recommended when the vehicle is not in motion. • Automatic downloaded phonebook entries cannot be deleted or edited. • Press the button to begin. • After the “Ready” prompt and the following beep, say “Phonebook Edit”.
• After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. Y ou can either say the name of a phonebook entry that you wish to delete or you can say “List Names” to hear a list of the entries in the phonebook from which you choose.
List All Names in the Uconnect™ Phonebook • Press the button to begin. • After the “Ready” prompt and the following beep, say “Phonebook List Names”. • The Uconnect™ Phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available.
Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your mobile phone. Press the button to place the current call on hold and answer the incoming call.
Conference Call When two calls are in progress (one active and one on hold), press and hold the button until you hear a double beep indicating that the two calls have been joined into one conference call.
Call Continuation Call continuation is the progression of a phone call on the Uconnect™ Phone after the vehicle ignition key has been switched to OFF .
Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not r eachable and the Uconnect™ Phone is operational, you may r each the emergency number as follows: • Press the button to begin.
W ARNING! T o use your Uconnect™ Phone System in an emer- gency , your mobile phone must be: • turned on, • paired to the Uconnect™ System, • and have network coverage. T owing Assistance If you need towing assistance: • Press the button to begin.
V oice Mail Calling T o learn how to access your voice mail, refer to “W orking with Automated Systems”. W orking with Automated Systems This method is used in instances wher e one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system.
NOTE: • Y ou may not hear all of the tones due to mobile phone network configurations. This is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
Dialing Using the Mobile Phone Keypad Y ou can dial a phone number with your mobile phone keypad and still use the Uconnect™ Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures).
Advanced Phone Connectivity T ransfer Call to and from Mobile Phone The Uconnect™ Phone allows ongoing calls to be trans- ferred from your mobile phone to the Uconnect™ Phone without terminating the call.
• Y ou can also press the button at any time while the list is being played, and then choose the phone that you wish to select. • The selected phone will be used for the next phone call.
Y ou can either press the Uconnect™ Phone button to restor e the factory setting or repeat the words and phrases when prompted by the Uconnect™ Phone. For best results, the V oice T raining session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off.
• Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say “Send”.
• Performance, such as audio clarity , echo, and loudness to a large degr ee rely on the phone and network, and not the Uconnect™ Phone. • Echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down.
Send Messages: Y ou can send messages using Uconnect™ Phone. T o send a new message: • Press the button. • After the “Ready” prompt and the following beep, say “SMS Send” or “Send Messages”. • Y ou can either say the message you wish to send or say “List Messages”.
16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me T urn SMS Incoming Announcement ON/OFF T urning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming messages. • Press the button.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 141 I n f o r m a t i o n P r o v i d e d b y :.
142 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 143 I n f o r m a t i o n P r o v i d e d b y :.
V oice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate (s) call cancel confirmation prom.
V oice Commands Primary Alternate (s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oi.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party r esponsible for compliance could void the user’s authority to operate the equipment.
When you press the V oice Command button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options.
Commands The V oice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pressing the V oice Command button.
• “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Radio FM T o switch to the FM band, say “FM” or “Radio FM”.
Disc T o switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “T rack” (#) (to change the track) • “Next T rack” (to play the next track) • “Pre.
• “Change to setup” • “Main menu setup” or • “Switch to setup” In this mode, you may say the following commands: • “Language English” • “Language French” • “Language .
SEA TS Seats are part of the Occupant Restraint System of the vehicle. W ARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
W ARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Manual Seat Height Adjustment — If Equipped The driver’s seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat; push downward on the handle to lower the seat.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
T o return the seat to a sitting position, rotate the seatback upright until it locks and push the seat rearwar d until the track locks. NOTE: • The front passenger seats have a track memory , which returns the seat to just past the halfway point of the track regardless of its original position.
Tip n’ Slide Seats — T wo-Door Models This featur e allows the fr ont seats to be rotated towar d the instrument panel to allow easier entry into the rear seats. Driver’s Seat Pull upward on the recline lever and bring the seatback to its full forward position.
Passenger Seat In addition to Easy Entry , the fr ont passenger seat is also equipped with T ip n’ Slide. This feature allows for easier entry for rear passengers. Pull upward on the recline lever and slide the entire seat forward (Easy Entry). W ith the seat forward, pull the entire seat assembly toward the instrument panel.
Heated Seats — If Equipped On some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. There are two heated seat switches that allow the driver and passenger to operate the seats independently .
W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
Front Head Restraints T o raise the head restraint, pull upward on the head restraint. T o lower the head restraint, press the adjust- ment button, located on the base of the head restraint, and push downward on the head restraint. Rear Head Restraints The rear seat is equipped with nonadjustable head re- straints.
1. Lift the seatback release lever and fold the seatback forward. 2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4.
Removing The Rear Seat — T wo-Door Models W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Replacing The Rear Seat — T wo-Door Models Reverse the steps for removing the seat. W ARNING! • T o help protect against personal injury , passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the vehicle.
T o Fold Down The Rear Seat Locate the pull strap (lower outboard side of seat), and pull it toward you until the seatback releases. T o Raise The Rear Seat Raise the seatback and lock it into place. If interference from the cargo area pr events the seatback from fully locking, you will have difficulty returning the seat to its proper position.
TO OPEN AND CLOSE THE HOOD Release both the hood latches. Raise the hood and locate the safety latch, located in the middle of the hood opening. Push the latch to the left side of the vehicle, to open the hood. Y ou may have to push down slightly on the hood befor e pushing the safety latch.
LIGHTS Multifunction Lever The multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The multifunction lever is located on the left side of the steering column.
Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. T o turn the system on, turn the end of the multifunction lever to the AUTO position (third detent). When the system is on, the Headlight T ime Delay feature is also on.
T urn Signals Move the multifunction lever up or down and the arr ows on each side of the instrument cluster flash to show proper operation of the front and r ear turn signal lights. NOTE: • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned OFF , a chime will sound to alert the driver when the driver’s door is opened. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam.
Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. Rotate the center portion of the lever upward to the last detent to turn on the interior lighting.
Cargo Lamp The courtesy and dome lights will turn on when the fr ont doors are opened, by rotating the control for the dimmer switch on the multifunction lever fully upwar d, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter .
When a door is open and the interior lights are on, rotating the dimmer control to the extr eme bottom posi- tion will cause all the interior lights to turn off. This is also known as the “Party” mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery .
Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation.
NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield W ashers T o use the washer , pull the lever toward you and hold while spray is desired.
Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. NOTE: The mist featur e does not activate the washer pump; ther efore, no washer fluid will be sprayed on the windshield.
TIL T STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever . Push down on the lever to unlock the steering column. W ith one hand firmly on the steering wheel, move the steering column up or down, as desir ed.
W ARNING! (Continued) the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death.
NOTE: In order to ensure pr oper operation, the Elec- tronic Speed Control System has been designed to shut down if multiple Speed Contr ol functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
T o Deactivate A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Contr ol without erasing the set speed memory . Pr essing the ON/OFF button or turning the ignition switch OFF erases the set speed memory .
Pressing the SET (-) button once will result i na1m p h (1.6 km/h) decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph (1.6 km/h). T o Accelerate For Passing Press the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed.
ELECTRICAL POWER OUTLET There are two 12 V olt (13 Amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet adapters. The front power outlet is powered from the ignition switch. Power is available when the ignition switch is in the ON or ACC position.
A second power outlet is located inside the center console and is powered directly from the vehicle battery . CAUTION! • Do not exceed the maximum power of 160 W atts (13 Amps) at 12 V olts. If the 160 W att (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., mobile phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
POWER INVERTER — IF EQUIPPED There is a 1 15 V olt, 150 W att inverter outlet located on the front of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 W atts.
inverter should automatically reset. If the power rating exceeds approximately 170 W atts, the power inverter may have to be reset manually . T o r eset the inverter manually press the power inverter button OFF and ON. T o avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter .
CUPHOLDERS Front Cupholders The front cupholders are located in the center console. Rear Cupholders The rear cupholders are located on the back of the center console.
STORAGE Glovebox Storage The lockable glovebox storage compartment is located on the passenger side of the lower instrument panel. Pull outward on the handle/latch to open the compartment. Console Storage Compartment T o lock or unlock the storage compartment, insert the ignition key and turn.
Rear Storage Compartment The r ear cargo ar ea storage compartment cover is held by a spring-loaded latch. In order to remove the r ear storage compartment cover , use the following procedur e: NOTE: The rear storage compartment latch should not be used as cargo tie-down.
DUAL TOP — TWO-DOOR MODELS — IF EQUIPPED If your vehicle is equipped with a Dual T op, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar . The soft top was installed at the factory for shipping purposes only .
3. Remove the soft top bow assembly pivot bracket screws (two per side) using a #T30 T orx 威 head driver . 4. Disconnect the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location.
6. Reinstall the hard top. Refer to “Freedom T op Three- Piece Modular Hard T op — Front/Rear Panel Instal- lation” in this section. Installing The Soft T op — T wo-Door Models NOTE: The following pr ocedures ar e for first time set up only . For futur e soft top procedur es, refer to “Soft T op” in this section.
3. Install the door frames. Refer to “Door Frame” in this section. 4. If the soft top has been removed, follow these steps to reinstall the soft top.
NOTE: T o aid in reattaching the knuckles, you may carefully tap on the knuckles using a rubber mallet. 4. Screw the pivot screws back into place using a #T30 T orx 威 head driver . Secure them until they are snug, being careful not to cross-thread the screws or over- tighten.
1. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. NOTE: Be sure the wire harness in the left r ear corner is not tangled in the soft top bows before you lift the top. 2. Unsnap and remove the black boot cover . This cover should be discarded.
Removing The Soft T op — Four-Door Models 1. Locate and remove the two boxes that contain the following items: • Right and left door frames • Six door frame attachment knobs • Right and left q.
4. Slide the tether strap up the side bow and attach to pivot bracket to secure side bows before removing soft top (both sides). 5. Remove the soft top bow assembly pivot bracket screws (two per side) from the sport bar using a #T30 T orx 威 head driver .
Remove the soft top from the vehicle and store in a clean, dry location (another person may be needed to help with this operation). 7. Reinstall the hard top. Refer to “Freedom T op Three- Piece Modular Hard T op — Front/Rear Panel Instal- lation” in this section.
4. Install the soft top with the pivot bracket above the sport bar bracket, lower the pivot bracket onto the sport bar bracket mounting tab in a downward motion to lock into tab (another person may be needed to help with this operation). 5. Screw the pivot screws back into place using a #T30 T orx 威 head driver .
CAUTION! Do not overtighten the screws. Y ou can strip the screws if they are overtightened. 6. Remove the tether strap from the pivot bracket and slide down the side bow (both sides). 7. Button the side bow tether strap (both sides). 8. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside.
9. Unsnap and remove the black boot cover . This cover should be discarded. It was intended as a protective cover for shipping only . NOTE: A visual instruction sheet is enclosed in the dual top wrap. 10. Put up the soft top. Refer to “Soft T op — Putting Up The Soft T op” in this section.
CAUTION! (Continued) • The hard top assembly must be positioned prop- erly to ensure sealing. Improper installation can cause water to leak into the vehicles interior . • Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicles interior .
3. T urn the center L-shaped locks (two) from the center of the roof panel. 4. T urn the rear L-shaped lock (located above the shoul- der belt anchorage).
5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. T o remove the right panel, follow the steps above except for Step 3.
Insert the right side Freedom panel into the bag with the latches facing downward. Unfold the black panel divider (ensure the divider is laying flat). Secure the V elcro, located at the center of the divider .
Insert the left-side Freedom panel into the bag with the latches facing upward. NOTE: Ensure the front Freedom panel latch is closed prior to inserting the panel into the bag.
Install the seat attachment strap (at the top of the bag) through the loops. Lift the Freedom bag into the vehicle with the hooks and straps facing the back of the r ear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat.
W rap the upper strap ar ound the r ear head restraints and loop the strap through the buckle. Pull on the strap to tighten the Freedom bag securely against the rear seat. Front Panel(s) Installation NOTE: Set the panels on the windshield frame so that there is no over hang.
Front Panel(s) Installation With Rear Hard T op Removed 1. T urn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90 degrees. NOTE: The front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang.
4. Remove the six T orx 威 head screws that secur e the har d top to the vehicle (along the interior bodyside) using a #40 T orx 威 head driver . 5. Open the swing gate all the way to ensur e clearance of the rear window glass. Lift the rear window glass.
7. Release the red locking tab by pulling outward to the right. 8. T o remove the wiring harness press the tab and pull downward to disconnect. Red Locking T ab Press T ab T o Disconnect 212 UNDERST A.
9. T o remove the washer hose, pinch the grips on hose connector and pull downward. 10. Close the swing gate. 1 1. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. CAUTION! The removal of the Freedom T op requires four adults located on each corner .
Make sure that the hard top is sitting flush with the body at the sides and check to ensure that there is a uniform gap between the lift glass and hard top. NOTE: • The T orx fasteners that attach the hard top to the body should be torqued to 66 in lb +/- 22 in lb (7.
CAUTION! (Continued) • Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle’s interior . • The door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior .
2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location.
Door Frame Installation — T wo-Door Models 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubber seal at the top of the windshield.
5. Starting with the fr ont knob, screw in and tighten both knobs. Repeat on the other side. Door Frame Installation — Four-Door Models 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening.
3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch the material of the sports bar covers and to ensure it is properly positioned on the seal above the front of the rear door . 4. Loosely install the rear knob (long knob) to hold the door rail in position.
6. Clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. 7. Position the rear of the fr ont door frame to lay on top of the fr ont of the rear door frame. Ensure the seals are installed correctly to avoid water leaks.
SOFT TOP — TWO-DOOR MODELS Please visit the owners section of Jeep.com for instruc- tional videos. CAUTION! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc.
CAUTION! (Continued) • Refer to “Appearance Care For Fabric T op Models” in “Maintaining Y our V ehicle” for further informa- tion. It contains important information on cleaning and caring for your vehicle’s fabric top. • Do not use any tools (screwdrivers, etc.
CAUTION! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior .
2. Remove the back window . 3. Release header latches from the windshield frame. 224 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
4. Release the sail panel retainers fr om the body side channel at the rear corners of the vehicle. NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow . 5. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top.
6. Release the Sunrider 威 latch (both sides). 7. Open the swing gate and lower the top. NOTE: Ensure fabric does not overhang the sides of the vehicle.
Quick Steps T o Raising The Soft T op Refer to “Raising The Soft T op” in this section for further information. 1. Open the swing gate and raise the top, engaging the Sunrider 威 latches (another person may be needed to help with this operation).
2. Engage header latches. 3. Install rear corner panels. 228 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
4. Install the back window . 5. Install the side windows. 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 229 I n f o r m a t i o n P r o v i d e d b y :.
6. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can r esult in wind and water leaks or damage to the window .
Lowering The Soft T op 1 — Header Bow 6 — Quarter W indow 2 — 2–Bow 7 — Check Strap 3 — 3–Bow 8 — Front Retainer — Quarter W indow 4 — Sail Panel 9 — Bottom Retainer — Quarter .
1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels 232 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer .
5. Before unzipping the rear window , r elease the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearwar d out of the swing gate brackets. • Unzip the rear window starting at the right lower corner of the window .
6. Remove the rear window retainer fr om the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the V elcr o 威 that runs along the top and rear edge of the side window . 9. Beginning from the rear lower corner , completely unzip the window .
1 1. Finish r eleasing the sail panel r etainers from the body side channel at the rear corners of the vehicle. NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow . 12. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top.
13. The swing gate brackets do not need to be removed unless the hard top is being installed. T o remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Completely release the latches from the loops on the windshield frame.
15. Make sure the plastic sleeves are slid rearward over the Sunrider 威 link (Sunrider 威 Models only). 16. Unlatch the side bows from both door rails (Sunrider 威 Models only).
17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Move to the fr ont of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward the rear of the vehicle.
Raising The Soft T op 1. Unclip and move the sun visors to the side. 2. Install door frames, if r emoved. Refer to “Door Frame” in this section for further information. 3. Make sure the plastic sleeve is slid over Sunrider 威 link (Sunrider 威 Models only).
5. Make sure the Sunrider 威 bracket on the side bows latches to the door rails (Sunrider 威 Models only). 6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches).
7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearwar d and over the channel until it snaps onto the exterior part of the rail. T o be properly located, the bracket must only be clipped to the shortened rail edge.
9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) towar d the rear window loose (on both sides).
1 1. Insert the fr ont retainer of the window into the door channel, making sure the r etainer is fully seated and properly positioned on the door frame.
12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the V elcr o 威 along the top and rear of the window .
13. Locate the black swing gate bar . Slide the swing gate bar over the receiver at the bottom inside of the rear window . The spongy part of the seal should be down and pointed outwar d to seal with the swing gate when closed. 14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening.
15. Run the zipper fully around to the right side of the window . 16. Grasp the swing gate bar and position it into the swing gate brackets. 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 247 I n f o .
17. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel.
SOFT TOP — FOUR-DOOR MODELS Please visit the owner’s section of Jeep.com for instruc- tional videos. CAUTION! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc.
CAUTION! (Continued) • Do not lower the top with the windows installed. W indow and top damage may occur . • Refer to “Appearance Care for Fabric T op Models” in “Maintaining Y our V ehicle” for further informa- tion. It contains important information on cleaning and caring for your vehicle’s fabric top.
CAUTION! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior .
Quick Steps For Lowering The Soft T op 1. Remove the side windows. 2. Remove the back window . NOTE: Start zipper from the right side to remove back window .
3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle.
5. Fold the sail panels so that they rest on top of the soft top. 6. Fold header rearwar d, pulling the fabric to the rear . 254 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r .
7. Release Sunrider 威 latch (both sides). 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 255 I n f o r m a t i o n P r o v i d e d b y :.
8. Open the swing gate and lower the top. NOTE: Ensure the fabric does not overhang the sides of the vehicle. Quick Steps For Raising The Soft T op 1. Open the swing gate and raise the top, engaging the Sunrider 威 latches (another person may be needed to help with this operation).
2. Install rear corner panels. 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 257 I n f o r m a t i o n P r o v i d e d b y :.
3. Rotate the header forward. 4. Engage the header latches. 258 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
5. Install the back window . 6. Install the side windows. 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 259 I n f o r m a t i o n P r o v i d e d b y :.
7. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can r esult in wind and water leaks or damage to the window .
Folding Down The Soft T op 1 — Header Bow 6 — Body Side Retainer 2 — 2–Bow 7 — Quarter W indow 3 — 3–Bow 8 — Check Strap 4 — 4–Bow 9 — Front Retainer — Quarter W indow 5 — Sa.
1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels 262 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer .
4. Open the swing gate. 5. Before unzipping the rear window , r elease the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearwar d out of the swing gate brackets. • Unzip the rear window starting at the right lower corner of the window .
6. Remove the rear window retainer fr om the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the V elcr o 威 that runs along the top and rear edge of the side window . 9. Beginning from the rear lower corner , completely unzip the window .
1 1. Finish r eleasing the sail panel r etainers from the body side channel at the rear corners of the vehicle. NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow . 12. Fold the sail panels so that they rest on top of the soft top.
13. The swing gate brackets do not need to be removed unless the hard top is being installed. T o remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Grasp the front side bow behind the header , and lift the top.
15. Fold back the front section of the top, pulling the fabric r earward. Gently rest the header on top of the rear portion of the deck. 16. Fold the top so that the material forms a ⬙ W ⬙ as shown. Enter the vehicle and move the material into two folds.
17. Release the side bows by pressing down on the latch above the front of the r ear door . Push the top rearwar d to disengage. Repeat this step on the other side. 18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light.
19. Gently slide the side bows off the door frame track and lower the top down into the vehicle. NOTE: Help from another person will ease this operation. 20. T uck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle.
Putting Up The Soft T op NOTE: Be extremely careful when putting up the soft top to pr event the doors fr om getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “Door Frame” in this section for further information.
5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into the Sunrider 威 locking mechanisms that ar e located above the fr ont of the r ear doors.
7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches).
10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. T o be properly located, the bracket must only be clipped to the shortened rail edge.
Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid in reaching the channel with the retainers.
13. Insert the fr ont retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame.
14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the V elcr o 威 along the top and rear of the window .
15. Locate the black swing gate bar . Slide the swing gate bar over the receiver at the bottom inside of the rear window . The spongy part of the seal should be down and pointed outwar d to seal with the swing gate when closed. 16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening.
17. Run the first zipper fully around to the right side of the window . 18. Grasp the swing gate bar and position it into the swing gate brackets. 19. Insert the rear window retainer into the swing gate bracket on both the left and right sides.
20. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 21. Close the header latches and r eturn the sun visors to their secured position.
Opening The Sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward.
4. Grasp the header and lift the top back. Make sur e the material is folded back as shown. NOTE: The Sunrider 威 latch on the door rail should not be activated for Sunrider 威 use. If activated, the soft top must be reinstalled starting from the sail panels.
Closing The Sunrider 姞 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their original positions.
Opening The Sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header , and lift the top.
4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙ W ⬙ as shown.
6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and V elcro 威 to itself; use one strap on each side of the vehicle. Closing The Sunrider 姞 Perform the above steps in the opposite order . NOTE: Failure to fold the fabric r earward will allow the material to sag and may block the rearview mirror .
Raise the windshield and r einstall the side bars as soon as the task that requir ed their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-r oad and off-r oad, regar dless of whether the windshield is raised or folded down.
Lowering The Windshield And Removing Side Bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. NOTE: T o assist in properly reinstalling side bars, mark the original locations prior to removing.
7. Remove the one hex bolt (13 mm) visible thr ough the plastic trim on the bottom side of the side bar , one hex bolt (13 mm) on the side of the side bar , and one hex bolt (13 mm) on top of the side bar . NOTE: Pull side bar out horizontally when removing.
W ARNING! Y ou or others could be injured if you carry the side bars loose in your vehicle. Remove the side bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps.
12. Lower the windshield gently until it contacts the rubber hood bumpers. 13. Secure the windshield by passing a cinch strap through the footman hoop on the center of the hood and on the center of the windshield frame. T ighten the strap to secure the windshield in place.
3. Attach the front of the side bar to the windshield frame. • Install the top two hex bolts (13 mm) first, then the lower side hex bolt (13 mm). The lower side bolt will not align until the top two bolts are installed. 4. T ighten all side bar attachment bolts.
REAR WINDOW FEA TURES — HARD TOP ONL Y Rear Window Wiper/W asher — If Equipped A r otary switch on the center portion of the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function.
Rear Window Defroster — If Equipped The rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster . An indicator in the button will illuminate when the rear window defroster is on.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 INSTRUMENT P ANEL FEA TURES ......... .298 䡵 INSTRUMENT CLUSTER ................ .299 䡵 INSTRUMENT CLUSTER DESCRIPTIONS .... .300 䡵 COMP ASS AND TRIP COMPUTER — IF EQUIPPED ...................
▫ System Status ....................... .331 ▫ Personal Settings (Customer-Pr ogrammable Features) .......................... .331 䡵 MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) ................ .335 ▫ Operating Instructions - Radio Mode .
▫ Operating Instructions — Radio Mode ...... .365 ▫ Operation Instructions — CD MODE for CD and MP3 Audio Play ............... .371 ▫ Notes On Playing MP3 Files ............. .374 ▫ LIST Button (CD Mode for MP3 Play) ...... .376 ▫ INFO Button (CD Mode for MP3 Play) .
INSTRUMENT P ANEL FEA TURES 1 — Air Outlet 7 — Climate Controls 2 — Instrument Cluster 8 — Power Outlet 3 — Radio 9 — Lower Switch Bank 4 — Assist Handle 10 — Power Mirror Switch — I.
INSTRUMENT CLUSTER 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 299 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. 2.
7. Seat Belt Reminder Light When the ignition switch is first turned to ON/ RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
1 1. Brake W arning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low , or that ther e is a pr oblem with the anti-lock brake system reservoir .
W ARNING! (Continued) It will take longer to stop the vehicle. Y ou could have a collision. Have the vehicle checked immediately . V ehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electr onic Brake Force Distribution (EBD).
13. Air Bag W arning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
gauge to pass ⬙ H. ⬙ In this case, a continuous chime will sound, until the engine is allowed to cool or the 4 minutes duration is expired, whichever come first.
W ARNING! (Continued) look under the hood yourself, see “Maintaining Y our V ehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph. 19. Cruise Indicator This indicator shows when the electronic speed control system is turned on.
the vehicle manufacturer on the vehicle placar d or tire inflation pressur e label. (If your vehicle has tires of a differ ent size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressur e for those tires.
TPMS fr om functioning pr operly . Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tir es and wheels allow the TPMS to continue to function properly . CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
V ehicle Odometer Messages When the appropriate conditions exist, the following odometer messages will display: ECO ..................... Fuel Saver Indicator door ............................ Door Ajar gA TE ....................... Swing Gate Ajar LoW tirE .
(e.g., snow plowing, of f-road operation). If this “HOT - OIL” message turns on, stop the vehicle and run the engine at idle or faster with the transmission in NEU- TRAL until the message turns off.
CHAngE OIL Message Y our vehicle is equipped with an engine oil change indicator system. The “CHANgE OIL” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval.
Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not requir e towing.
engine running. If the “ESC Activation/Malfunction In- dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
27. Sway Bar Indicator Light — If Equipped This indicator will illuminate when the front sway bar is disconnected. 28. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Con- trol (ESC) is off.
30. Electronic V ehicle Information Center (EVIC) Display/ Compass Mini-T rip Computer Display — If Equipped When the appropriate conditions exist, this display shows the Electronic V ehicle Information Center (EVIC) messages. For further information, refer to “Electronic V ehicle Information Center”.
Control Buttons The Compass/T emperature control buttons are located on the left spoke of the steering wheel. Press and release the STEP button on the steering wheel to access the options in the Compass display .
Compass/T emperature Display NOTE: If the vehicle is equipped with a Chrysler Uconnect™ gps (Navigation Radio), the NA V system will provide the compass direction, and the variance and calibration menus will be unavailable. The compass will perform accurately , based on GPS signals instead of the Earth’s magnetic field.
T o change the zone, press and release the STEP button to increase the variance one step. Repeat as necessary until the desired variance is achieved. NOTE: The factory default zone is 8. During pr ogram- ming, the zone value will wrap around from zone 15 to zone 1.
NOTE: • A good calibration requires a level surface and an envi- ronment free from large metallic objects such as build- ings, bridges, underground cables, railroad tracks, etc. • Magnetic materials should be kept away fr om the top of the center of the instrument panel.
T rip Conditions T rip Odometer (ODO) / ECO (Fuel Saver Indicator) — If Equipped This display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer to T rip A or T rip B or to ECO.
T rip A Shows the total distance traveled for trip A since the last reset. T rip B Shows the total distance traveled for trip B since the last reset. ECO (Fuel Saver Indicator) — If Equipped The ECO.
This system conveniently allows the driver to select a variety of useful information by pr essing the switches mounted on the steering wheel. The EVIC consists of the following: • Compass Heading (N.
MENU Button Press and r elease the MENU button to advance the display to each of the EVIC Main Menu features or to r eturn to the Main Menu from a sub-menu. Upon reaching the last item in the Main Menu the EVIC will advance to the first item in the Main Menu with the next MENU button press and release.
Electronic V ehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages: • Low T ire Pressur e • Service TPM System (refer to ⬙ T i.
• Check Gascap (r efer to “Adding Fuel” in “Starting And Operating” for more details) • Oil Change Required (with a single chime) • ECO (Fuel Saver Indicator) — if equipped Oil Change Required Y our vehicle is equipped with an engine oil change indicator system.
EVIC Main Menu T o step to each main menu feature press and r elease the MENU button once for each step. A step from the last item in the list will cause the first item in the feature list to be displayed.
NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature can also affect the displayed temperature; therefore, temperature readings are not updated when the vehicle is not moving.
Manual Compass Calibration If the compass appears erratic and the “CAL” indicator does not appear in the EVIC display , you must put the compass into the Calibration Mode manually as follows: 1. Start the engine. Leave the shift lever in P ARK in order to enter the EVIC Programming Menus.
T o Change The Compass V ariance: 1. T urn the ignition switch RUN (it is not necessary to start the engine). 2. Press the MENU button until Personal Settings (Customer-Pr ogrammable Featur es) displays in the EVIC. 3. Press the DOWN button until “Compass V ariance” message and the last variance zone number displays in the EVIC.
Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy , according to the current fuel tank level.
System Status Displays SYSTEM OK if ther e are no active W arning Messages stored. Pressing and releasing the DOWN button when SYSTEM OK is displayed will do nothing.
Auto Unlk On Exit When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the P ARK or NEUTRAL position and the driver’s door is opened. T o make your selection, press and release the SELECT button until “On” or “Off” appears.
when exiting the vehicle. T o make your selection, press and release the SELECT button until “0,” “30,” “60,” or “90” appears. Headlamps with Wipers (A vailable with Auto Headlights On.
Hill Start Assist (HSA) — If Equipped When on is selected, the HSA system is active. Refer to “Electronic Brake Contr ol System” in “Starting And Operating” for system function and operating informa- tion. T o make your selection, press and release the SELECT button until “On” or “Off” appears.
MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
TIME Button Press the TIME button to alternate locations of the time and frequency display . Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL contr ol knob to set the minutes.
Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display .
T oggle the MUSIC TYPE button to select the following format types: Program T ype 16-Digit Character Display No program type or undefined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls R.
By pr essing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next fr equency station with the same selected Music T ype name.
NOTE: • The available selections for each of the above entries varies depending upon the disc. • These selections can only be made while playing a DVD. • VES™ Power - Allows you to turn VES™ ON and OFF (if equipped). • VES™ Lock - Locks out rear VES™ remote controls (if equipped).
Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc).
a disc is loaded, changes will not be effective. Also, the defaults are ef fective only if the disc supports the customer-pr eferred settings. AM and FM Buttons Press the buttons to select AM or FM mode. SET Button — T o Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory , press the SET button.
Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play , DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play . If the region code for the DVD disc does not match the region code for the radio DVD player , it will not play the disc.
Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corr esponding number (1-6) wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to remove the disc.
Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however , acceptable MP3/WMA file r ecording media and formats ar e limited. When writing MP3/WMA files, pay attention to the following restrictions.
If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files named with the *.
ID3 T ag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium.
INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through the following T AG information: Song T itle, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙ elapsed time ⬙ priority mode.
TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day . The time of day will display for five seconds.
DTS™ “DTS™ and “DTS™ 2.0” are trademarks of Digital Theater Systems, Inc. Uconnect™ Multimedia (Satellite Radio) — If Equipped Satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast.
T o access the ESN/SID, refer to the following steps: ESN/SID Access W ith the ignition switch in the ON/RUN or ACC posi- tion and the radio on, pr ess the SETUP button and scroll using the TUNE/SCROLL control knob until Sirius ID is selected. Press the TUNE/SCROLL contr ol knob and the Sirius ID number will display .
Operating Instructions - Uconnect™ Multimedia (Satellite) Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
MUSIC TYPE Button Pressing this button once will turn on the Music T ype mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected. T oggle the MUSIC TYPE button again to select the music type.
Y ou may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory .
MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display .
Y ou may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stor ed into pushbutton memory .
If you insert a disc with the ignition ON/RUN and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display .
Notes on Playing MP3 Files The radio can play MP3 files; however , acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc T ypes) The MP3 file recor ding media supported by the radio are CDDA, CD-R, CD-RW , MP3, and CDDA+MP3.
Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs cr eated with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs.
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
MEDIA CENTER 130 WITH SA TELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL contr ol knob to set the minutes.
Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display .
T oggle the MUSIC TYPE button to select the following format types: Program T ype 16-Digit Character Display No program type or undefined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls R.
By pr essing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next fr equency station with the same selected Music T ype name.
Y ou may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stor ed into pushbutton memory .
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display .
Notes On Playing MP3 Files The radio can play MP3 files; however , acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc T ypes) The MP3 file recor ding media supported by the radio are CDDA, CD-R, CD-RW , MP3, and CDDA+MP3.
Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs cr eated with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs.
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Press and hold the INFO button again for three seconds to return to ⬙ elapsed time ⬙ display . Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows .
how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1.
Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
additional thr ee seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display). R W/FF Pressing the R W (Rewind) or FF (Fast Forward) buttons causes the tuner to sear ch for the next channel in the direction of the arrows.
SET Button – T o Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory , press the SET button. The symbol SET 1 will now show in the display window . Select the button (1-6) you wish to lock onto this channel and press and r elease that button.
iPod 姞 /USB/MP3 CONTROL — IF EQUIPPED NOTE: This section is for sales code RES and REQ/ REL/RET radios only with Uconnect™. For sales code RBZ/RHB, RHR, RHP , RHW or RB2 touch-screen radio iPod 威 /USB/MP3 control feature, refer to the separate RBZ/RHB, RHR, RHP , RHW or RB2 User’s Manual.
Once the audio device is connected and synchronized to the vehicle’s iPod 威 /USB/MP3 control system (iPod 威 or external USB device may take a few minutes to connect), the audio device starts charging and is ready for use by pressing radio switches, as described below .
Controlling The iPod 姞 Or External USB Device Using Radio Buttons T o get into the iPod 威 /USB/MP3 contr ol mode and access a connected audio device, either press the “AUX” button on the radio faceplate or press the VR button and say ⬙ USB ⬙ or ⬙ Switch to USB ⬙ .
• Use the << SEEK and SEEK >> buttons to jump to the previous or next track. Pressing the SEEK >> button during play mode will jump to the next track in the list, or press the VR button and say ⬙ Next or Previous T rack ⬙ .
List Or Browse Mode During Play mode, pressing any of the buttons described below , will bring up List mode. List mode enables scrolling thr ough the list of menus and tracks on the audio device. • TUNE control knob: The TUNE control knob functions in a similar manner as the scroll wheel on the audio device or external USB device.
• T o exit List mode without selecting a track, press the same PRESET button again to go back to Play mode . • LIST button: The LIST button will display the top level menu of the iPod 威 or external USB device. T urn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob.
Bluetooth Streaming Audio (BTSA) Music can be streamed from your cellular phone to the Uconnect™ phone system. Controlling BTSA Using Radio Buttons T o get into the BTSA mode, press either “AUX” button on the radio or press the VR button and say “Bluetooth Streaming Audio”.
STEERING WHEEL AUDIO CONTROLS The remote sound system controls ar e located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker -type switch with a pushbutton in the center and controls the volume and mode of the sound system.
Radio Operation Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch will “Seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset pushbutton.
4. Do not use solvents such as benzene, thinner , cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc wher e temperatures may become too high. NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.
Manual Heating And Air Conditioning The Manual T emperature Controls consist of a series of outer rotary dials and inner push knobs. Blower Control Rotate this contr ol to regulate the amount of air forced through the venti- lation system in any mode.
T emperature Control Rotate this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures.
Bi-Level Air is directed through the panel and floor outlets. NOTE: For all settings, except full cold or full hot, there is a dif ference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditions.
NOTE: • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur . Extended use of this mode is not recommended. • The use of the Recirculation mode in cold or damp weather will cause windows to fog on the inside, because of moisture buildup inside the vehicle.
Automatic T emperature Control (A TC) — If Equipped Automatic Operation The Automatic T emperature Control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger . Operation of the system is quite simple.
The recommended setting for maximum comfort is 72°F (22°C) for the average person; however , this may vary . NOTE: • The temperatur e setting can be adjusted at anytime without affecting automatic operation.
398 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
The operator can override the AUTO mode setting to change airflow distribution by r otating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow .
• Air Conditioner Control Press this button to turn on the air conditioning during manual operation only . When the air conditioning is turned on, cool dehumidified air will flow thr ough the outlets selected with the Mode control dial. Press this but- ton a second time to turn OFF the air conditioning.
• Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation mode by pressing the Recirculation button. However , under certain conditions, while in Automatic mode, the system is blowing air out the defr ost vents.
W indow Fogging Interior fogging on the windshield can be quickly re- moved by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes a problem, increase blower speed.
Control Setting Suggestions For V arious W eather Conditions 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 403 I n f o r m a t i o n P r o v i d e d b y :.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 ST ARTING PROCEDURES ............... .410 ▫ Manual T ransmission – If Equipped ....... .410 ▫ Automatic T ransmission – If Equipped ..... .410 ▫ Normal Starting ....................... 4 1 1 ▫ Extreme Cold W eather (Below –20°F Or −29°C) .
䡵 FOUR–WHEEL DRIVE OPERA TION (COMMAND-TRAC I 威 OR ROCK-TRAC 威 ) . . . .428 ▫ Operating Instructions/Precautions ....... .428 ▫ Shift Positions ....................... .430 ▫ Shifting Procedure .................... .431 䡵 TRAC-LOK 威 REAR AXLE — IF EQUIPPED .
▫ T raction Control System (TCS) ........... .457 ▫ Brake Assist System (BAS) .............. .457 ▫ Hill Start Assist (HSA) ................ .458 ▫ Electronic Roll Mitigation (ERM) ......... .462 ▫ Electronic Stability Control (ESC) ........
▫ Limited-Use Spare – If Equipped ......... .488 ▫ T ire Spinning ....................... .489 ▫ T read W ear Indicators ................. .490 ▫ Life Of T ire ........................ .490 ▫ Replacement T ires .................... .491 䡵 TIRE CHAINS (TRACTION DEVICES) .
䡵 TRAILER TOWING .................... .515 ▫ Common T owing Definitions ............ .515 ▫ T railer Hitch Classification .............. .518 ▫ T railer T owing W eights (Maximum T railer W eight Ratings) ..................... .519 ▫ T railer And T ongue W eight .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Normal Starting NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. T urn the ignition switch to the ST AR T position and release when the engine starts.
W ARNING! (Continued) • If the vehicle has a discharged battery , booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly . Refer to “Jump Starting” in “What T o Do In Emergen- cies” for further information.
W ith T ip Start – Automatic T ransmission Only If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold W eather” proce- dures, it may be flooded. T o clear any excess fuel, push the accelerator pedal all the way to the floor and hold it.
MANUAL TRANSMISSION — IF EQUIPPED W ARNING! Y ou or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline.
Shifting Fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. Y ou should always use first gear when starting from a standing position.
Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed. Downshift progr essively .
Manual T ransmission Downshift Speeds in MPH (KM/H) Gear Selec- tion 6t o5 5t o4 4t o3 3t o2 2t o1 Maxi- mum Speed 80 (129) 70 (1 13) 50 (81) 30 (48) 15 (24) NOTE: V ehicle speeds shown in the chart above are for 2H and 4H only , vehicle speeds in 4L would be signifi- cantly less.
AUTOMA TIC TRANSMISSION — IF EQUIPPED CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
W ARNING! (Continued) number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever . Do not leave the ignition key in or near the vehicle. A child could operate power windows, other controls, or move the vehicle.
Five-Speed Automatic T ransmission The shift lever position display (located in the instrument cluster) indicates the transmission gear range. Y ou must press the brake pedal to move the shift lever out of P ARK (refer to “Brake/T ransmission Shift Interlock System” in this section).
Gear Ranges DO NOT race the engine when shifting from P ARK or NEUTRAL into another gear range. NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold.
W ARNING! • Never use the P ARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • Y our vehicle could move and injure you and others if it is not completely in P ARK.
W ARNING! (Continued) reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever . Do not leave the key in or near the vehicle. A child could operate power windows, other controls, or move the vehicle.
NEUTRAL Use this range when the vehicle is standing for pr olonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into P ARK if you must leave the vehicle. W ARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.
When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into str ong head winds, or while towing heavy trailers), u.
5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will r eturn to normal operation. NOTE: Even if the transmission can be reset, we r ecom- mend that you visit your authorized dealer at your earliest possible convenience.
W ARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing an accident or personal injury .
FOUR–WHEEL DRIVE OPERA TION (COMMAND-TRAC I 姞 OR ROCK-TRAC 姞 ) W ARNING! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. Y ou could have a collision. Do not drive the vehicle unless the transfer case is fully engaged.
In the event that additional traction is required, the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together , forcing the front and rear wheels to rotate at the same speed. This is accom- plished by simply moving the shift lever to one of these positions.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.
speed. This range (4L) provides additional traction and maximum pulling power for loose, slippery r oad surfaces only . Do not exceed 25 mph (40 km/h). The “4WD Indicator Light” (located in the instrument cluster) will illuminate when the transfer case is shifted into the 4L position.
W ARNING! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. Y ou could have a collision. Do not drive the vehicle unless the transfer case is fully engaged.
AXLE LOCK (TRU–LOK 姞 ) — RUBICON MODELS The AXLE LOCK switch is located on the instrument panel (to the left of the steering column). This feature will only activate when the following con- ditions are met: • Key in ignition, vehicle in 4L (Low) range.
ELECTRONIC SW A Y BAR DISCONNECT — IF EQUIPPED Y our vehicle may be equipped with an electronic discon- necting stabilizer/sway bar . This system allows greater front suspension travel in off-r oad situations. This system is controlled by the SW A Y BAR switch located on the instrument panel (to the left of the steering column).
sway bar should remain in on-road mode during normal driving conditions. W ARNING! Do not disconnect the stabilizer bar and drive on hard-surfaced roads or at speeds above 18 mph (29 km/h); you may lose control of the vehicle, which could result in serious injury .
T o return to on-road mode, pr ess the SW A Y BAR switch again. W ARNING! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury .
OFF-ROAD DRIVING TIPS Side Step Removal – If Equipped NOTE: Prior to off-r oad usage, the side steps should be removed to prevent damage. 1. Remove the two nuts from the bodyside. 2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly .
The Basics Of Off-Road Driving Y ou will encounter many types of terrain driving off- road. Y ou should be familiar with the terrain and ar ea before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice.
extreme situations such as deep snow , mud, steep in- clines, or sand where additional low speed pulling power is needed. V ehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L (Low) range. CAUTION! Do not use 4L (Low) range when operating the vehicle on dry pavement.
Mud Deep mud creates a great deal of suction around the tires and is very difficult to get through. Y ou should use second gear (manual transmission), or DRIVE (automatic transmission), with the transfer case in the 4L (Low) position to maintain your momentum.
Crossing Obstacles (Rocks And Other High Points) While driving off-r oad, you will encounter many types of terrain. These varying types of terrain bring dif ferent types of obstacles. Befor e proceeding, review the path ahead to determine the correct approach and your ability to safely recover the vehicle if something goes wrong.
CAUTION! • Never attempt to straddle a rock that is large enough to strike your axles or undercarriage. • Never attempt to drive over a rock which is large enough to contact the door sills.
CAUTION! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered. Getting High-Centered If you get hung up or high-centered on .
Before Climbing A Steep Hill As you approach a hill, consider its grade or steepness. Determine if it is too steep. Look to see what the traction is on the hill side trail.
Driving Downhill Before driving down a steep hill, you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too steep to maintain a slow , controlled des.
If Y ou Stall Or Begin T o Lose Headway If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake.
accelerate through the cr ossing. After crossing any water higher than the bottom of the axle differ entials, you should inspect all of the vehicle fluids for signs of water ingestion.
Crossing Puddles, Pools, Flooded Areas Or Other Standing W ater Puddles, pools, flooded or other standing water ar eas normally contain murky or muddy waters. These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.
W ARNING! Never drive through fast moving deep water . It can push your vehicle downstream, sweeping it out of control. This could put you and your passengers at risk of injury or drowning. After Driving Off-Road Off-r oad operation puts more stress on your vehicle than does most on-r oad driving.
W ARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. Y ou might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary .
• Upon initial start-up in cold weather , the power steer- ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.
W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary , add fluid to r estore to the pr oper indicated level.
When the parking brake is applied with the ignition switch ON, the “Brake W arning Light” in the instrument cluster will illuminate. NOTE: • When the parking brake is applied and the automatic transmission is placed in gear , the “Brake W arning Light” will flash.
W ARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever .
ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressur e to prevent wheel lock-up and help avoid skidding on slippery surfaces.
W ARNING! (Continued) • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can they increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
W ARNING! The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the ve- hicle, nor can they increase the traction afforded by prevailing road conditions. The ABS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence. Do not reduce brake pedal pressur e unless braking is no longer desired.
W ARNING! (Continued) another vehicle or object. T o avoid this, do not apply throttle while pressing the clutch pedal until you are ready to release the clutch.
HSA On Automatic T ransmission V ehicles The system will work in REVERSE, and all forward gears on vehicles equipped with an automatic transmission. The system will not activate if the vehicle is placed in NEUTRAL.
W ARNING! (Continued) • HSA is not a parking brake. Always apply the parking brake fully when leaving your vehicle. Also, be certain to leave the transmission in P ARK. Failure to follow these warnings may cause the vehicle to roll down the incline and could collide with another vehicle, object or person, and cause serious or fatal injury .
6. Cycle ignition switch OFF then ON. 7. If the sequence was completed properly , the “ESC Activation/Malfunction Indicator Light” will blink several times to confirm HSA is off. Steps 1-7 must be completed within 90 seconds to turn of f HSA. Repeat steps 1-7 to re-enable HSA functionality .
W ARNING! (Continued) capabilities of an ERM-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Electronic Stability Control (ESC) This system enhances dir ectional control and stability of the vehicle under various driving conditions.
W ARNING! Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction af forded by prevailing road conditions. ESC cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing.
When in ⬙ Partial Off ⬙ mode, the TCS portion of ESC has been disabled and the “ESC Activation/Malfunction Indicator Light” will be illuminated.
ESC OFF switch. This will restor e normal “ESC On” mode of operation. W ARNING! W ith the ESC switched off, the enhanced vehicle stability offered by ESC and ERM are unavailable. In an emergency evasive maneuver , the ESC and ERM systems will not engage to assist in maintaining stability .
W ARNING! W ith the ESC switched off, the enhanced vehicle stability offered by ESC and ERM are unavailable. In an emergency evasive maneuver , the ESC and ERM systems will not engage to assist in maintaining stability . The “Full Off” mode is intended for of f- road use only .
ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON position. It should go out with the engine running.
The “ESC OFF Indicator Light” indicates the Electronic Stability Control (ESC) is off. T railer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway .
Hill Descent Control (HDC) – If Equipped HDC is only intended for low speed of f-road driving. HDC maintains vehicle speed while descending hills in off-r oad driving conditions by applying the brakes when necessary . The symbol indicates the status of the Hill Descent Control (HDC) feature.
Enabling HDC 1. Shift the transfer case into 4WD LOW range. Refer to “Four-Wheel Drive Operation” in “Starting and Oper- ating” for further information. 2. Press the “Hill Descent” button. The “Hill Descent Control Indicator Light” in the instrument cluster will turn on solid.
NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can ca.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire T erminology And Definitions T erm Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door . Cold T ire Inflation Pressure Cold tire inflation pressure is defined as the tire pressur e after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
Tire Loading And Tire Pressure T ire Placard Location T ire Placard Location (T wo-Door Model) T ire Placard Location (Four-Door Model) 5 ST ARTING AND OPERA TING 477 I n f o r m a t i o n P r o v i d.
T ire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressur es for the front, rear , and spare tires.
T o determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the T ire and Loading Information placard.
NOTE: • The following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle.
5 ST ARTING AND OPERA TING 481 I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear pat- terns to develop across the tire tr ead.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the T ire Pressure Monitoring Sensor . Inflation pressures specified on the placard are always “cold tire inflation pressur e.
Tire Pressures For High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressur e is very important.
the tire sidewall. Use all season tir es only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Summer Or Three Season Tires – If Equipped Summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice.
Spare Tire Matching Original Equipped Tire And Wheel – If Equipped Y our vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle.
Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and r einstalled on your vehicle at the first opportunity . Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tir e.
your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity . W ARNING! Limited-use spares are for emergency use only . Instal- lation of this limited-use spare tire affects vehicle handling.
T read Wear Indicators T read wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators ar e molded into the bottom of the tr ead grooves. They will appear as bands when the tr ead depth becomes 1/16 in (2 mm).
W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose control and have a collision resulting in serious injury or death.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, result- ing in changes to steering, handling, and braking of your vehicle.
• P225/75R16 or a P235/65R17 tir e with the use of a traction device that meets the SAE type “Class S” specification is recommended. W ARNING! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling.
TIRE ROT A TION RECOMMENDA TIONS The tires on the fr ont and rear of your vehicle operate at differ ent loads and perform differ ent steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires.
CAUTION! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. T ire rotation schedule should be followed to balance tire wear .
must be increased to the recommended cold placard pressur e in order for the “T ire Pressure Monitoring T elltale Light” to be turned OFF . The system will auto- matically update and the “T ire Pressure Monitoring T elltale Light” will extinguish once the updated tire pressur es have been received.
CAUTION! (Continued) • After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the T ire Pressure Moni- toring Sensor .
Premium and Base TPM System The T ire Pressure Monitor System (TPMS) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pr essure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressur e readings to the Receiver Module.
received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The “T ire Pressur e Monitoring T elltale Light” will flash on and off for 75 seconds, and will remain on solid when a system fault is detected.
3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: • If your vehicle is equipped with a match.
below the low-pr essure warning limit in any of the four active road tir es. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information.
T ire Pressure Monitoring Low Pressure W arnings The T ire Pressur e Monitoring T elltale Light will illuminate in the instrument cluster , and an au- dible chime will be activated, when one or more of the four active r oad tir e pr essures are low .
The system will automatically update, the graphic dis- play of the pressur e value(s) will stop “flashing,” and the T ire Pr essure Monitoring T elltale Light will extinguish once the updated tire pressur e(s) have been r eceived. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
If the ignition switch is cycled, this sequence will r epeat, providing the system fault still exists. If the system fault no longer exists, the “T ire Pressure Monitoring T elltale Light” will no longer flash, the ⬙ SER VICE TPM SYSTEM ⬙ message will not be present, and a pressure value will be displayed instead of dashes.
message to appear in the EVIC, and the graphic display will still show the low tire pressur e value “flashing.” Driving the vehicle for up to 20 minutes above 15 mph (24 km/h) will turn OFF the “T ire Pressure Monitoring T elltale Light” as long as none of road tires ar e below the low pressure warning threshold.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the W orld- wide Fuel Charter , WWFC) which define fuel pr operties necessary to deliver enhanced emissions, performance, and durability for your vehicle.
E-85 Usage In Non-Flex Fuel V ehicles Non-FFV vehicles are compatible with gasoline contain- ing 10% ethanol (E10). Gasoline with higher ethanol content may void the vehicle’s warranty .
can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and Califor - nia reformulated gasoline. Materials Added T o Fuel All gasoline sold in the United States is requir ed to contain effective detergent additives.
Carbon Monoxide Warnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel (Continued) CAUTION! (Continued) cap (gas cap).
W ARNING! (Continued) • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling. NOTE: • When the fuel nozzle “clicks” or shuts of f, the fuel tank is full.
VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar .
T ire Size The tire size on the V ehicle Certification Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire size listed.
items down low and be sure that the weight is distributed equally . Stow all loose items securely befor e driving. Improper weight distributions can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR.
exceed the GVWR. Refer to “V ehicle Loading/V ehicle Certification Label” in “Starting and Operating” for further information. Gross T railer W eight (GTW) The GTW is the weight of the trailer.
Frontal Area The fr ontal area is the maximum height multiplied by the maximum width of the front of a trailer . T railer Sway Control – If Equipped The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue.
W ARNING! • An improperly adjusted W eight Distributing Hitch system may reduce handling, stability , braking performance, and could result in a collision.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ T ransmission Axle Model GCWR (Gross Combined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.
Engine/ T ransmission Axle Model GCWR (Gross Combined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) Max. T railer T ongue Wt. (See Note) 3.6L/Manual 3.21 T wo–Door Sahara Model (4WD) 5,430 lbs (2 463 kg) 25 sq ft (2.32 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.
Engine/ T ransmission Axle Model GCWR (Gross Combined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) Max. T railer T ongue Wt. (See Note) 3.6L/ Automatic 4.10 T wo–Door Rubicon Model (4WD) 6,533 lbs (2 963 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.
Engine/ T ransmission Axle Model GCWR (Gross Combined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) Max. T railer T ongue Wt. (See Note) 3.6L/Manual 3.21 Four–Door Sahara Model (4WD) 5,782 lbs (2 623 kg) 32 sq ft (2.97 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.
Engine/ T ransmission Axle Model GCWR (Gross Combined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) Max. T railer T ongue Wt. (See Note) 3.6L/ Automatic 4.10 Four–Door Rubicon Model (4WD) 8,431 lbs (3 824 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) Refer to local laws for maximum trailer towing speeds.
T railer And T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle.
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
W ARNING! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be dif ficult for the driver to control.
W ARNING! (Continued) • T otal weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1.
T owing Requirements – T railer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer . This could cause inadequate braking and possible personal injury . • An electronically actuated trailer brake controller is requir ed when towing a trailer with electronically actuated brakes.
T owing Requirements – T railer Lights And W iring Whenever you pull a trailer , regar dless of the trailer size, stop lights and turn signals on the trailer are requir ed for motoring safety . The T railer T ow Package will include a four–pin wiring harness.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.
Electronic Speed Control – If Equipped • Do not use in hilly terrain or with heavy loads. • When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • Use speed control in flat terrain and with light loads to maximize fuel efficiency .
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) T owing This V ehicle Behind Another V ehicle T owing Condition Wheels OFF the Ground Four-Wheel Drive Models Flat T ow NONE See Instructions • Automati.
Recreational T owing – Four-Wheel Drive Models NOTE: The transfer case must be shifted into NEUTRAL (N), automatic transmission must be shifted into P ARK, and manual transmission must be placed in gear (NOT in NEUTRAL) for recreational towing. CAUTION! • Front or rear wheel lifts should not be used.
Shifting Into NEUTRAL (N) Use the following procedure to prepar e your vehicle for recr eational towing. W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL (N) position without first fully engaging the parking brake.
7. Shift the transmission into REVERSE. 8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat Steps 7 and 8 with automatic transmission in DRIVE or manual transmission in first gear .
Shifting Out of NEUTRAL (N) Use the following procedure to prepar e your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. T urn the ignition switch to the LOCK/OFF position.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 HAZARD W ARNING FLASHERS .......... .538 䡵 IF YOUR ENGINE OVERHEA TS ........... .538 䡵 JACKING AND TIRE CHANGING ......... .540 ▫ Jack Location ....................... .541 ▫ Spare T ire Stowage ......
HAZARD W ARNING FLASHERS The Hazar d W arning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the Hazard W arning flasher . When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency .
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
JACKING AND TIRE CHANGING W ARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traf fic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous.
Jack Location The jack and lug wrench are located in the rear storage compartment. NOTE: T urn the black plastic wing nut counter clock- wise to loosen the jack from the storage bin.
Spare Tire Stowage T o r emove the spare tire from the carrier , r emove the tir e cover , if equipped, and r emove the lug nuts with the lug wrench turning them counterclockwise.
Jacking Instructions W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground.
5. Raise the vehicle by turning the jack scr ew to the right. Raise the vehicle till the tire is raised from the surface of the r oad. Minimum tire lift provides maximum stability . W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision.
7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end towar d the wheel. Lightly tighten the lug nuts clockwise. W ARNING! T o avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered.
10. Remove the jack assembly and wheel blocks. 11 . Secure the tire, jack, and tools in their proper locations. 12. Remove blocks from wheels. W ARNING! A loose tire or jack thrown forward in a collision or hard stop, could endanger the occupants of the ve- hicle.
JUMP-ST ARTING PROCEDURES If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be danger ous if done impr operly so please follow the procedures in this section carefully .
Preparations For Jump-Start The battery in your vehicle is located in the right rear of the engine compartment, behind the Power Distribution Center . W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON.
1. Set the parking brake, shift the automatic transmission into P ARK (manual transmission in NEUTRAL) and turn the ignition to LOCK. 2. T urn of f the heater , radio, and all unnecessary electri- cal accessories.
3. Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery . 4. Connect the opposite end of the negative (-) jumper cable to a good engine gr ound (exposed metal part of the dischar ged vehicle’s engine) away fr om the battery and the fuel injection system.
CAUTION! Accessories that can be plugged into the vehicle power outlets draw power from the vehicle’ s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’ s battery will discharge suf ficiently to degrade battery life and/or prevent the engine from starting.
Control” in “Starting And Operating” for further infor- mation. Once the vehicle has been freed, press the ⬙ ESC Off ⬙ switch again to restor e ⬙ ESC On ⬙ mode.
EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, they are mounted in the front and the rear . NOTE: For off-r oad recovery , it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle.
3. Using a small scr ewdriver or similar tool, r emove the shift lever override access cover (located to the right of the shift lever). 4. T urn the ignition to the ACC or ON/RUN position, but do not start the engine. 5. Press and maintain firm pressur e on the brake pedal.
TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commer cial wrecker service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational T owing” in the “Starting And Operating” section.
Proper towing or lifting equipment is r equired to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer ’s instructions.
Four–Wheel Drive Models The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods ar e to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly .
MAINT AINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMP AR TMENT — 3.6L ......... .561 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .562 ▫ Loose Fuel Filler Cap Message ........... .562 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS ..................
▫ Clutch Hydraulic System (Manual T ransmission) – If Equipped ............. .588 ▫ Manual T ransmission – If Equipped ....... .588 ▫ T ransfer Case ....................... .589 ▫ Front/Rear Axle Fluid ................. .590 ▫ Appearance Care And Protection From Corrosion .
ENGINE COMP ARTMENT — 3.6L 1 — Integrated Power Module (Fuses) 7 — W asher Fluid Reservoir 2 — Battery 8 — Engine Coolant Reservoir 3 — Engine Oil Dipstick 9 — Air Cleaner Filter 4 — A.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboar d diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a r ow , the system will turn on the MIL.
4. Approximately 15 seconds later , one of two things will happen: • The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could r esult in civil penalties being assessed against you.
CAUTION! (Continued) • Y our vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering or air conditioning.
CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New V ehicle Limited W arranty . Engine Oil V iscosity – 3.6L Engine SAE 5W -20 engine oil is recommended for all operating temperatures.
station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be r eplaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufactur er’s engines have a full-flow type oil filter .
Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably . Only high quality filters should be used to assure most efficient service. MOP AR 威 engine air cleaner filters ar e a high quality filter and are r ecom- mended.
CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case.
W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
MOP AR 威 Spray White Lube or equivalent to assure quiet, easy operation and to protect against rust and wear . Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
Adding W asher Fluid The fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. The fluid reservoir is located in the engine compartment. Be sur e to check the fluid level at regular intervals. Fill the r eservoir with windshield washer solvent only (not radiator anti- freeze).
into the passenger compartment. In addition, have the exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. W ARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless.
Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Cooling System W ARNING! Y ou or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator . If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.
Cooling System – Drain, Flush, And Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals.
CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator .
Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area wher e the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types is not recommended and can result in cooling system damage.
Disposal Of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community .
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant expansion bottle. • Check the coolant freeze point in the radiator and in the coolant expansion bottle.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically . Refer to the “Maintenance Schedule” for the proper maintenance intervals. W ARNING! Riding the brakes can lead to brake failure and possibly a collision.
W ARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.
Automatic T ransmission – If Equipped Selection Of Lubricant It is important to use the pr oper transmission fluid to ensure optimum transmission performance and life.
CAUTION! • Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque con- verter shudder . Using a transmission fluid other than that recommended by the manufacturer , and will require more frequent fluid and filter changes.
4. Place the shift lever momentarily into each gear posi- tion (allowing time for the transmission to fully en- gage in each position), ending with the shift lever in P ARK. 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides.
7. Check for leaks. Release the parking brake. NOTE: T o prevent dirt and water from entering the transmission after checking or replenishing fluid, make sure that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube.
Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.76 mm) below the bottom of the hole. Add fluid, if necessary , to maintain the proper level.
Adding Fluid Fluid should be added only at filler hole until fluid begins to run out of the hole. Drain First remove the fill plug (B), then the drain plug (C). The recommended tightening torque for the drain and fill plugs is 15 to 25 ft lbs (20 to 34 N·m).
Selection Of Lubricant Use only manufactur er’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information.
W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using MOP AR 威 Car W ash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water .
• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the responsibility of the owner . • If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repair ed as soon as possible.
Interior Care Use MOP AR 威 T otal Clean or equivalent to clean fabric upholstery and carpeting. Interior T rim should be cleaned starting with a damp cloth, a damp cloth with MOP AR 威 T otal Clean or equiva- lent , then MOP AR 威 Spot & Stain Remover or equivalent if absolutely necessary .
When cleaning the rear view mirror , spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror . Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic.
• Do not allow any vinyl cleaner to run down and dry on the paint, leaving a streak. • After cleaning your vehicle’s fabric top, always make sure it is completely dry before lowering. • Be especially careful when washing the windows by following the directions for “Care of Fabric T op W in- dows.
CAUTION! (Continued) • The front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior . Care Of Fabric T op Windows CAUTION! Y our vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by following these directions: 1.
regularly . Use MOP AR 威 Soft T op Zipper Cleaner and Lubricant or equivalent to ease zipper operation. Before applying, make sure the zipper teeth are clear of sand, mud, and other materials. Clean both sides of the zipper , not just one side. Rinse both zipper halves with fr esh water and allow to dry .
Cavity Car- tridge Fuse Mini Fuse Description J1 — — J2 30 Amp Pink T ransfer Case Module J3 — — J4 25 Amp Natural Driver Door Node J5 25 Amp Natural Passenger Door Node J6 40 Amp Green Anti-L.
Cavity Car- tridge Fuse Mini Fuse Description J13 60 Amp Y ellow Ignition Off Draw (IOD) – Main J14 40 Amp Green Rear Defroster J15 40 Amp Green Front Blower J17 40 Amp Green Starter Solenoid J18 20.
Cavity Car- tridge Fuse Mini Fuse Description M4 — — M5 25 Amp Natural Power Inverter – If Equipped M6 20 Amp Y ellow Power Outlet #1/ Rain Sensor M7 20 Amp Y ellow Power Outlet #2 (BA TT/ACC SE.
Cavity Car- tridge Fuse Mini Fuse Description M12 30 Amp Green Amplifier M13 20 Amp Y ellow Ignition Off Draw – Cabin Compartment Node, W ireless Con- trol Module, SIREN, Multifunction Control Switc.
Cavity Car- tridge Fuse Mini Fuse Description M18 15 Amp Blue Right T ail/Park/ Run Lamp M19 25 Amp Natural Auto Shut Down (ASD #1 and #2) M20 15 Amp Blue Cabin Compartment Node Interior Light, Switch.
Cavity Car- tridge Fuse Mini Fuse Description M29 10 Amp Red Powertrain M30 15 Amp Blue W iper Motor Frt, J1962 Diagnostic Feed M31 20 Amp Y ellow Backup Lamps M32 10 Amp Red Airbag Controller , TT EU.
CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Mod- ule, and possibly result in an electrical system failure.
REPLACEMENT BULBS Interior Bulbs Bulb Number Automatic T ransmission Indicator Lamp 658 Heater Control Lamps (2) 194 Rocker Switch Indicator Lamp (Rear W indow Defogger , and Rear W ash/W ipe) ** Soundbar Dome Lamp 912 ** Bulbs only available from authorized dealer .
BULB REPLACEMENT NOTE: Lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor . T urning the lamps on will usually accelerate the clearing process.
Front Park/T urn Signal 1. Remove the front grille. T urn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other . 3. T urn the socket assembly 1/4 turn counterclockwise and remove from housing.
Rear T ail, Stop, T urn Signal, And Backup Lamp 1. Remove the two inboar d screws attaching the tail light housing to the body . DO NOT REMOVE THE OUTER SCREWS A T ANY TIME. 2. Separate the housing fr om the body by pushing the lamp inboard while pulling the lamp away from the body .
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) — T wo Door Models 18.6 Gallons 70 Liters Fuel (Approximate) — Four Door Models 22.5 Gallons 85 Liters Engine Oil with Filter 3.6L Engine 6 Quarts 5.6 Liters Cooling System * 3.6L Engine (MOP AR 威 Antifreeze/Engine Coolant 10 Y ear/152,000 Mile Formula or equivalent) 10.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 10 Y ear/150,000 Mile Formula OA T (Organic Additive T echnology) or equivalent meeting the requir ements of Chrysler Material Standard MS-12106.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission – If Equipped MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. Manual T ransmission – If Equipped MOP AR 威 Manual T ransmission Lubricant or equivalent (meeting the requir e- ments of Chrysler Material Standard MS-9224).
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE ............ .614 ▫ Maintenance Chart .................... .616 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e .
MAINTENANCE SCHEDULE Y our vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate.
Once A Month Or Before A Long T rip: • Check engine oil level • Check windshield washer fluid level • Check the tire inflation pressur es and look for unusual wear or damage • Check the fluid .
Maintenance Chart Refer to the Maintenance Schedules on the following pages for the requir ed maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 7.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 Or Y ears: 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 Or.
W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to per- form a service job, take your vehicle to a competent mechanic.
I n f o r m a t i o n P r o v i d e d b y :.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 SUGGESTIONS FOR OBT AINING SER VICE FOR YOUR VEHICLE .................. .625 ▫ Prepare For The Appointment ............ .625 ▫ Prepare A List ....................... .625 ▫ Be Reasonable W ith Requests .
䡵 PUBLICA TION ORDER FORMS ........... .630 䡵 DEP AR TMENT OF TRANSPOR T A TION UNIFORM TIRE QUALITY GRADES ........ .631 ▫ T readwear .......................... .631 ▫ T raction Grades ...................... .632 ▫ T emperature Grades .....
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you are having warranty work done, be sure to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner . This is why you should always talk to an authorized dealer service manager first.
In Mexico contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P . 05109 Mexico, D. F . In Mexico City: 5081-7568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or.
The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract.
MOP AR 姞 P ARTS MOP AR 威 fluids, lubricants, parts, and accessories ar e available fr om an authorized dealer . They are recom- mended for your vehicle in or der to help keep the vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And W ashington, D.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Master- card, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an or der form.
Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orldwide W eb at: • www .techauthority .com DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tir e grading categories wer e established by the National Highway T raffic Safety Administration.
T raction Grades The T raction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
ABS (Anti-Lock Brake System) ............... .303 Adding Engine Coolant (Antifreeze) ........... .579 Adding Fuel ............................ .510 Additives, Fuel .......................... .509 Airbag .................................. 6 2 Airbag Deployment .
Fluid Level Check ..................... .586 Fluid T ype .......................... .585 Special Additives ...................... .585 Autostick .............................. .426 Auxiliary Electrical Outlet (Power Outlet) ....... .182 Auxiliary Power Outlet .
Chart, T ire Sizing ........................ .473 Check Engine Light (Malfunction Indicator Light) ............... 3 1 1 Checking Y our V ehicle For Safety ............... 9 9 Checks, Safety ............................ 9 9 Child Restraint ...........
Cruise Light ............................ .306 Cupholders ............................ .188 Customer Assistance ...................... .625 Data Recorder , Event ....................... 7 5 Daytime Running Lights ................... .171 Dealer Service .
Emergency Brake ........................ .452 Emergency , In Case of Jacking ............................. .540 Jump Starting ........................ .548 T ow Hooks .......................... .554 Emission Control System Maintenance ......... .563 Engine Air Cleaner .
Filters Air Cleaner .......................... .569 Air Conditioning ...................... .402 Engine Oil ........................... .569 Engine Oil Disposal .................... .568 Flashers Hazard W arning ...................... .538 T urn Signal .
Requirements ........................ .506 T ank Capacity ........................ .610 Fueling ............................... .510 Fuses ................................. .598 Gas Cap (Fuel Filler Cap) .................. .510 Gasoline, Clean Air ...
Heated Seats ............................ .159 Heater ................................ .392 Heater , Engine Block ...................... .413 High Beam Indicator ...................... .301 Hill Descent Control ...................... .470 Hill Descent Control Indicator .
Key , Replacement .......................... 1 7 Keys ................................... 1 4 Key , Sentry (Immobilizer) .................... 1 6 Lane Change and T urn Signals ............... .301 Lane Change Assist ....................... .169 Lap Belts .
Illuminated Entry ....................... 2 1 Instrument Cluster ..................... .167 Interior ............................. .171 Lights On Reminder .................... .170 Low Fuel ........................... .300 Oil Pressure ...............
Master Cylinder (Brakes) ................... .583 Methanol .............................. .507 Mini-T rip Computer ...................... .315 Mirrors ................................. 1 1 1 Electric Powered ....................... 1 1 3 Electric Remote .
Oil Pressure Light ........................ .301 Onboard Diagnostic System ................. .562 Operating Precautions ..................... .562 Operator Manual (Owner’s Manual) ............. 6 Outside Rearview Mirrors ................... 1 1 2 Overdrive .
Rear W indow Features .................... .293 Rear W iper/W asher ....................... .293 Recorder , Event Data ....................... 7 5 Recreational T owing ...................... .532 Shifting into T ransfer Case Neutral (N) ...... .534 Shifting out of T ransfer Case Neutral (N) .
Adjustable Upper Shoulder Anchorage ........ 5 5 And Pregnant W omen .................... 6 1 Child Restraint ......................... 7 6 Extender .............................. 6 1 Front Seat ............................. 4 8 Inspection ...........
Shoulder Belt Upper Anchorage ................ 5 5 Side Airbag .............................. 7 0 Side W indow Demisters (Defrosters) ........... .402 Signals, T urn ........................... .103 Snow Chains (T ire Chains) .................. .492 Snow T ires .
Theft System Arming ....................... 2 0 Theft System Disarming ..................... 2 0 T ilt Steering Column ...................... .177 T ip Start ................................ 4 1 1 T ire and Loading Information Placard .......... .477 T ire Markings .
Recreational ......................... .532 W eight ............................. .519 T owing Assistance ........................ .130 T rac-Lok Rear Axle ....................... .432 T raction Control ......................... .457 T railer Sway Control (TSC) .
V anity Mirrors ........................... 1 1 4 V ariance, Compass ....................... .317 V ehicle Identification Number (VIN) ............. 8 V ehicle Loading ......................... .478 V ehicle Modifications/Alterations ............... 9 V ehicle Storage .
INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’ s electr onic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed pr operly by trained personnel.
P atriot 2013 I n f o r m a t i o n P r o v i d e d b y : 13JK72-126-AB 2nd Edition Printed in U.S.A. Chrysler Group LLC.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Jeep Wrangler Unlimited (2013) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Jeep Wrangler Unlimited (2013) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Jeep Wrangler Unlimited (2013), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Jeep Wrangler Unlimited (2013) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Jeep Wrangler Unlimited (2013), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Jeep Wrangler Unlimited (2013).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Jeep Wrangler Unlimited (2013). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Jeep Wrangler Unlimited (2013) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
