Manuel d'utilisation / d'entretien du produit Grand Cherokee (2007) du fabricant Jeep
Aller à la page of 472
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 ▫ Roll Over W arning ..................... 4 䡵 How T o Use This Manual .................. 6 䡵 W arnings And Cautions ................... 8 䡵 V ehicle Identification Number ..
INTRODUCTION Thank you for selecting a Jeep 威 Grand Cherokee and welcome to our worldwide family . This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended.
Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may r esult in an accident, roll over of the vehicle, and severe or fatal injury . Drive carefully .
NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings.
INTRODUCTION 7 1 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously af fect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 4 ▫ Ignition Key Removal ................... 1 4 ▫ Key-In-Ignition Reminder ................ 1 5 䡵 Sentry Key Immobilizer System ...........
▫ T ransmitter Battery Service ............... 2 3 䡵 Remote Starting System — If Equipped ........ 2 4 䡵 Door Locks ............................ 2 6 ▫ Manual Door Locks ..................... 2 6 ▫ Power Door Locks — If Equipped .........
▫ Safety Checks Y ou Should Make Inside T h e V e h i c l e .......................... 6 5 ▫ Safety Checks Y ou Should Make Outside The V e h i c l e .
A WORD ABOUT YOUR KEYS The keys for your new vehicle ar e enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number . The key code can also be obtained by your authorized dealer from your vehicle invoice.
W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever . Don’t leave the keys in the ignition.
light will come on for 3 seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a malfunction in the electronics. If the bulb begins to flash immediately after the ignition switch is turned on, this indicates that an invalid key is being used to start the vehicle.
Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been pr ogrammed to a vehicle, it cannot be programmed to any other vehicle. At the time of pur chase, the original owner is provided with a four digit PIN number .
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound. The SKIM indicator light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
the door lock plunger located on the inside of the doors or with the driver’s door key lock cylinder , will not set the alarm. T o Disarm the System T o disarm the system, use the r emote keyless entry transmitter . Also, using a valid sentry key and moving the ignition switch to the ON/ST AR T position will disarm the system.
NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work.
NOTE: If desired, the system can be pr ogrammed to unlock all doors on the first pr ess of the “Unlock” button. Refer to “Remote Unlock Driver’s Door 1st” in the Personal Settings section of the “Electronic V ehicle Infor- mation Center (EVIC)”, or simply follow these steps: 1.
W ARNING! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes.
2. While the “Unlock” button is pr essed, (after 4 seconds) press the “Lock” button. Release both buttons. The “Flash Lights On Lock/Unlock” featur e can be reactivated by repeating this procedure. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
1. W ith the transmitter buttons facing down, remove the small screw , and separate the two halves of the transmit- ter . Make sure not to damage the rubber gasket during removal. 2. Remove and replace the battery . A void touching the new battery with your fingers.
Once the vehicle has started, the engine will run for 15 minutes. T o cancel remote start, press the “Remote Start” button twice within two seconds. T o enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the “Unlock” button on the key fob.
DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefor e, make sure the keys are not inside the vehicle before closing the door .
If you pr ess the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers.
Child Protection Door Lock The r ear doors of your vehicle ar e equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks.
WINDOWS Power Windows The power window contr ols are located on the driver’s door trim panel. There is a single switch on the fr ont passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position.
Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically . T o cancel the “Auto Down” movement, operate the switch in either the up or down dir ection and release the switch.
W ARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
W ARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. Y ou and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked.
Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open. NOTE: If a power malfunction to the power liftgate latch should occur , an emergency liftgate latch release can be used to open the liftgate.
W ARNING! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate Latch Plate T o Buckle THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 37 2 I n f .
W ARNING! A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well.
5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The r etractor will withdraw any slack in the belt. 6. T o release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position.
Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best.
3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
NOTE: These devices ar e not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly . The pretensioners are triggered by the Occupant Re- straint Control (ORC) Module. Like the front airbags, the pretensioners are a single use item.
Driver And Front Passenger Supplemental Restraint Systems (SRS) This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment.
NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are no longer functional.
NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags. The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity .
Children that are not big enough to properly wear the vehicle seat belt should be secured in the r ear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or belt- positioning booster seats should ride properly buckled up in the rear seat.
W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
• Driver and Front Passenger Seat Belt Pretensioners How The Airbag System W orks • The Occupant Restraint Control (ORC) Module de- termines if a fr ontal, side, or r ollover collision is sever e enough to r equire the front and/or side airbags to inflate.
• The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags.
If A Deployment Occurs The airbag system is designed to deploy when the Occupant Restraint Control (ORC) Module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger , and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and seat belt retractor assem- bly , replaced by an authorized dealer as soon as possible.
Airbag W arning Light Y ou will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • Does not come on during the 6 to 8 seconds after the ignition switch is first turned on.
provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US govern- ment and various states.
Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces requir e that small children ride in proper restraint systems. This is the law , and you can be prosecuted for ignoring it.
• The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats often have a higher weight limit i.
Standards. The manufacturer also r ecommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
• If the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating position.
Children T oo Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the fr ont of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat.
kits or r etro-fit kits. Y ou are ur ged to take advantage of all the available attachments pr ovided with your child re- straint in any vehicle. NOTE: When using the LA TCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints ar e stowed and out of reach of children.
Installing the LA TCH-Compatible Child Restraint System W e urge that you carefully follow the directions of the manufacturer when installing your child r estraint. Not all child r estraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that were provided with the child restraint system.
In addition, there ar e tether strap anchorages behind each rear seating position located on the back of the seat. Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
T ransporting Pets Airbags deploying in the front seat could harm your pet. An unr estrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be r estrained in the rear seat in pet harnesses or pet carriers that are secur ed by seat belts.
SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breath- ing it can make you unconscious and can eventually poison you. T o avoid breathing (CO) follow the safety tips below .
Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.). If ther e is any question regar ding belt or retractor condition, replace the belt. Airbag W arning Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned on.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 M i r r o r s ............................... 7 2 ▫ Inside Day/Night Mirror ................. 7 2 ▫ Automatic Dimming Mirror — If Equipped .... 7 2 ▫ Outside Mirrors ...................
▫ Advanced Phone Connectivity ............. 9 2 ▫ Things Y ou Should Know About Y our UConnect™ System ..................... 9 4 䡵 Seats ................................. 9 9 ▫ Front Manual Seat Adjustment ............. 9 9 ▫ Front Seat Adjustment — Recline .
▫ Daytime Running Lights — If Equipped ..... 1 1 6 ▫ Lights-On Reminder ................... 1 1 7 ▫ Fog Lights — If Equipped ............... 1 1 7 ▫ T urn Signals ......................... 1 1 7 ▫ High Beam Switch .................... 1 1 8 ▫ Passing Light .
▫ BAS (Brake Assist System) ............... 1 3 1 ▫ ERM (Electronic Roll Mitigation) .......... 1 3 2 ▫ ESP (Electronic Stability Program) ......... 1 3 3 ▫ ESP/BAS W arning Lamp And ESP/TCS Indicator Light ....................... 1 3 7 䡵 Rear Park Assist System— If Equipped .
▫ Closing Sunroof - Express ............... 1 5 4 ▫ Pinch Protect Feature ................... 1 5 4 ▫ Pinch Protect Override ................. 1 5 4 ▫ V enting Sunroof - Express ............... 1 5 4 ▫ Sunshade Operation ................... 1 5 5 ▫ W ind Buffeting .
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror .
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean.
W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
Both mirrors will always move together and will fold anytime the knob is turned. The ignition switch does not have to be in the ON position. Driver’s Outside Automatic Dimming Mirror — If Equipped If your vehicle is equipped with a driver’s outside auto- matic dimming mirr or , it operates when the inside auto- matic dimming mirror is on.
Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this section for details. (See page 106 for more information.) Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice.
HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”W ork ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ).
The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www .chrysler .com/uconnect for supported phones.
Operations V oice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structur e. V oice commands are required after most UConnect™ system prompts. Y ou will be prompted for a specific command and then guided through the available options.
Cancel Command At any pr ompt, after the voice on beep, you can say ⬙ Cancel ⬙ and you will be r eturned to the main menu. However , in a few instances the system will take you back to the previous menu.
• For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • Y ou will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority .
• System will prompt you to say the name of the person you want call. • After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a previ- ously stored name entry in the UConnect™ phone- book.
The UConnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Delete. ⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete.
• The UConnect™ system will play the names of all the phonebook entries. • T o call one of the names in the list, press the ⬙ V oice Recognition’ button during the playing of the desired name, and then say ⬙ Call. ⬙ NOTE: the user can also exercise ⬙ Edit ⬙ or ⬙ Delete ⬙ operations at this point.
Making a Second Call while Current Call in Progress T o make a second call while you ar e curr ently in a call, press the ’V oice Recognition’ button and say ⬙ Dial ⬙ or ⬙ Call ⬙ followed by the phone number or phonebook entry you wish to call.
Call T ermination T o end a call in progr ess, momentarily press the ⬘ Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial.
• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
Y our phone must be turned on and paired to the UCon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. T owing Assistance If you need towing assistance, • Press the ’Phone’ button to begin.
When calling a number with your UConnect™ system that normally r equires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’V oice Recognition’ button and say the sequence you wish to enter followed by the word ⬙ Send.
Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures).
Information Service When using A T&T W ireless Service, dialing to phone number ⬙ #121, ⬙ you can access voice activated automated system to receive news, weather , stocks, traffic, etc.
Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously pair ed to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin.
Things Y ou Should Know About Y our UConnect™ System V oice Recognition (VR) • Always wait for the beep before speaking. • Speak normally , without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sur e that no one other than you is speaking during a voice recognition period.
• Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero). ⬙ 800 ⬙ must be spoken ⬙ eight-zero-zer o. ⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
96 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 97 3 I n f o r m a t i o n P r o v i d e d b y :.
98 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
Front Seat Adjustment — Recline T o adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. T o r eturn the seatback, lift the lever , lean forward, and release the lever .
Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support.
4 - W ay Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearwar d adjust- ment. The top switch controls the seatback recline adjust- ment.
center of the instrument panel. After turning on the ignition, you can choose from High, Off, or Low heat settings. Amber LEDs in the top portion of each switch indicate the level of heat in use. T wo LEDs are illumi- nated for high, one for low , and none for off.
W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
NOTE: Do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. NOTE: The automatic folding r ear head restraints will lower as the seat is folded down. T o Raise Rear Seat Raise the rear seatback and lock it into place.
Storage — Rear Seat Armrest (If Equipped) The r ear seat may be equipped with a center storage armrest. Press the latch and lift the top of the armr est to access the storage bin.
Keyless Entry transmitters can also be programmed to recall the same positions when the “Unlock” button is pressed. Y our vehicle may have been delivered with two Remote Keyless Entry transmitters. One or both transmitters can be linked to either memory position.
4. Adjust the brake and accelerator pedals to the desired positions. 5. T urn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 6. T urn the ignition switch to the OFF position and remove the key . 7. Pr ess and r elease the SET (S) button located on the driver’s door .
T o recall the memory settings for driver one, press memory button number 1 on the driver’s door or the “Unlock” button on the Remote Keyless Entry transmit- ter linked to memory position 1.
NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to Remote Linked to Memory under ⬙ Electr onic V ehicle Information Center (EVIC) — Customer Pro- grammable Features ⬙ in Section 4 for more information.
NOTE: The Easy Entry Easy Exit feature is not enabled when the vehicle is delivered from the factory . The Easy Entry Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic V ehicle Information Center (EVIC).
Then, reach under the hood, move safety latch to the left, and lift the hood. T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision.
LIGHTS Multi-Function Control Lever The multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights.
Headlights and Parking Lights T urn the end of the multi-function control lever to the first detent for parking light operation. T urn to the second detent for headlight operation. T urn to the third detent for “Auto” headlight operation (if equipped).
stop. Refer to “W indshield W ipers and W ashers” in this section for more information. (See page 120 for mor e information.) NOTE: When your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity .
T o Deactivate 1. Pull back on the muti-function control lever to manu- ally deactivate the system (normal operation of high beams). 2. Pull back on the multi-function control lever once again to re-activate the system.
Lights-On Reminder If the headlights or parking lights ar e on after the ignition is turned OFF , a chime will sound when the driver’s door is opened.
High Beam Switch Pull the multi-function control lever towards you to switch the headlights to “High” beam. The “High Beam Indicator Light” on the instrument cluster will illumi- nate. Pull the multi-function control lever a second time to switch the headlights to “Low” beam.
Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pr essing the r ecessed ar ea of the lens. T o turn these lights off, pr ess the r ecessed ar ea of the lens a second time. There are also reading lights located above the rear doors.
WINDSHIELD WIPERS AND W ASHERS The front and rear wipers and washers are operated by a switch in the right side control lever . T urn the end of the control lever to select “Lo,” “Hi,” or one of the five speed sensitive intermittent windshield wiper speeds.
T o use the washer , pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected.
Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver . The feature is especially useful for r oad splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of five settings to activate this feature.
driver desires more sensitivity . Place the wiper switch in the OFF position when not using the system. NOTE: • The rain sensing feature will not operate when the wiper switch is in the LOW or HIGH speed position. • The rain sensing feature may not function properly when ice, or dried salt water is present on the wind- shield.
TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place.
Press the left side of the button to move the pedals rearwar d (toward the driver). Press the right side of the button to move the pedals forward (away from the driver). • The pedals can be adjusted with the ignition OFF . • The pedals can be adjusted while driving.
CAUTION! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
T o Set at a Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, or pr essing the CANCEL button will deactivate the Speed Contr ol without erasing the memory .
T o Accelerate for Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
W ARNING! T o help keep your vehicle under control, do not use Speed Control under these conditions: • When it is not possible to keep your vehicle at a set speed. • On slippery roads, such as on snow or ice. • In heavy or varying traf fic volume, in traf fic that varies in speed, or on winding roads.
W ARNING! ABS (Anti-Lock Brake System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction af forded by prevail- ing road conditions. ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing.
BAS (Brake Assist System) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressur e to the brakes.
ERM (Electronic Roll Mitigation) This system anticipates the potential for wheel lift by monitoring the driver ’s steering wheel input and the speed of the vehicle.
ESP (Electronic Stability Program) This system enhances directional control and stability of the vehicle under various driving conditions. ESP cor - rects for over/under steering of the vehicle by applying the brake of the appr opriate wheel to assist in counter- acting the over/under steer condition.
W ARNING! ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESP cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
or gravel conditions and more wheel spin than ESP would normally allow is r equired to gain traction. T o turn ESP on again, momentarily depr ess the ⬙ ESP Contr ol Switch ⬙ .
In this mode, ESP and TCS, except for the “limited slip” feature described in the TCS section, are turned off until the vehicle r eaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h) the system returns to “Partial Of f” mode, described above.
40 mph (64 km/h). At 40 mph (64 km/h), the normal ESP stability function returns but TCS remains off. When the vehicle speed drops below 35 mph (56 km/h), the ESP system shuts off.
If the “ESP/BAS W arning Lamp” comes on continuously with the engine running, a mal- function has been detected in either the ESP or the BAS system, or both.
Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view . The monitored area seems oval in shape. The sensors can detect obstacles from approximately 1 1.
When the obstacle is detected at a distance of about 59 inches (150 cm) from the rear fascia, the outermost LEDs of the warning display will be ON with increased bright- ness. Along with the LED, a half second tone will occur . As the distance of the detected obstacle to the rear fascia decreases, mor e LEDs ar e illuminated.
When the switch is pressed to disable the system, the instrument cluster will display the ⬙ P ARK ASSIST DIS- ABLED ⬙ message. Refer to “Electronic V ehicle Informa- tion Center (EVIC)” in Section 4 of this manual.
Cleaning the Rear Park Assist System Clean the Rear Park Assist Sensors with water , car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors.
W ARNING! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before back- ing up.
REAR CAMERA — IF EQUIPPED V ehicles with a Navigation radio may be equipped with a rear view camera (located on the rear liftgate) that allows you to see an on-screen image (on the navigation radio screen) of the r ear of your vehicle whenever the vehicle is put into R (Reverse).
T urning the Rear Camera Off 1. T o turn the rear camera off, select “Rear Camera” at the Systems Settings screen and press ENTER. Refer to your “Navigation User’s Manual” for detailed operating instructions. 2. Select “OFF” at the “Rear Camera” screen.
The lights also turn on when a front door or rear door is opened. The lights will also turn on when the unlock button on the r emote keyless entry transmitter is pr essed. Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses.
W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards.
Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons. 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4 has been completed.
NOTE: T o program the remaining two HomeLink but- tons, begin with ⬙ Programming ⬙ step two. Do not repeat step one. NOTE: If your hand-held transmitter appears to pr o- gram the universal transce.
Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter sig- nals to ⬙ time-out ⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law , some U.
• Press and hold the two outer HomeLink buttons and release only when the EVIC display shows “CHAN- NELS CLEARED” (after 20 seconds). Release both buttons. Do not hold for longer that 30 seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙ Pro- gramming ⬙ - Step 2.
HomeLink 威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch.
Opening Sunroof - Express Press the switch rearwar d and release, and the sunroof will open automatically from any position. The sunr oof will open fully , then stop automatically . This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof.
Sunshade Operation The sunshade can be opened manually . However , the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears.
POWER OUTLET T o the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. The rear power outlet (if equipped) is located in the left rear cargo area.
All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use to protect the battery against discharge. CAUTION! Electrical Outlet Use W ith Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.
CUP HOLDERS In the center console there are two cup holders for the front seat passengers. NOTE: The cup holder insert is removable, fr om the console, for cleaning. It can be reinstalled with the larger cup depression towar ds the passenger seat, but the top surface will not be flush with the console surface.
CARGO AREA FEA TURES Cargo Light The cargo area light is activated by opening the liftgate, opening any door , or by rotating the dimmer control on the multi-function control lever to the extreme top posi- tion. If all doors are closed and only the liftgate is open, pushing on the car go light lens surface will turn off all interior lamps.
Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy , not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. T o cover the cargo area: 1. Grasp the cover at the center handle.
W ARNING! In an accident a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting.
W ARNING! Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
W ARNING! T o help protect against personal injury , passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only , not for passengers, who should sit in seats and use seat belts. Cargo Load Floor The panel in the load floor is reversible for added utility .
1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray . 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray .
If the liftgate flipper glass is open, connection to the rear window wiper is interr upted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch or the ignition switch needs to be turned OFF and ON to restart the rear wiper .
ROOF LUGGAGE RACK — IF EQUIPPED External racks do not increase the total load carrying capacity of the vehicle. Be sur e that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity .
CAUTION! • T o prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without cross rails in- stalled. The load should be secured and placed on top of the cross rails, not directly on the roof.
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel And Controls ............. 1 7 2 䡵 Instrument Cluster ...................... 1 7 3 ▫ Gasoline Engine ...................... 1 7 3 ▫ Diesel Engine ........................ 1 7 4 䡵 Instrument Cluster Description .
䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio W ith Optional Satellite Radio, Hands Free Phone, And V ehicle Entertainment Systems (VES) Capabilities ........................... 1 9 9 ▫ Operating Instructions - Radio Mode ....... 1 9 9 ▫ Operation Instructions - (CD Mode For CD Audio P l a y ) .
䡵 Satellite Radio — If Equipped .............. 2 2 6 ▫ System Activation ..................... 2 2 7 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) .................... 2 2 7 ▫ Selecting Satellite Mode In REF Radios ......
INSTRUMENT P ANEL AND CONTROLS 172 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER Gasoline Engine UNDERST ANDING YOUR INSTRUMENT P ANEL 173 4 I n f o r m a t i o n P r o v i d e d b y :.
Diesel Engine 174 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake W arning Light The BRAKE warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb re- paired promptly .
engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly . Certain conditions such as a loose or missing gas cap, poor fuel quality , etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles.
8. T achometer The red segments indicate the maximum permissible engine r evolutions-per-minute (r .p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator . 9. Security Alarm System Indicator Light — If Equipped This light will flash rapidly for appr oximately 15 seconds when the vehicle theft alarm is arming.
12. T ire Pressur e Monitoring T elltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pr essure label.
CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. If you decide to look under the hood your- self, refer to Section 7 of this manual. Follow the warnings under “Cooling System Pressure Cap.
18. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
is placed in the P (Park) position. The light should turn off. If the light remains lit with the engine running your vehicle will usually be drivable, however , see your dealer for service as soon as possible.
ELECTRONIC VEHICLE INFORMA TION CENTER — IF EQUIPPED The electronic vehicle information center (EVIC) located in the instrument cluster , when the appropriate condi- tions exist, will display the following messages and symbols. Some of the messages are accompanied by a chime.
• LIFTGA TE/DOOR OPEN (with graphic) • LIFTGA TE/DOORS OPEN (with graphic) • LIFTGLASS OPEN (with graphic) • HOOD OPEN (with graphic) • HOOD/DOOR OPEN (with graphic) • HOOD/DOORS OPEN (wit.
• CHECK GAS CAP • ESP OFF • MEMOR Y #1 POSITIONS SET • MEMOR Y #2 POSITIONS SET • MEMOR Y SYSTEM DISABLED — SEA TBEL T F AS- TENED (with graphic) • MEMOR Y SYSTEM DISABLED — VEHICLE NO.
Customer Programmable Features Press the MENU button until one of the display choices following appears: Language? When in this display you may select one of thr ee lan- guages for all display nomenclatur e, including the trip computer functions. Press the STEP button while in this display selects English, Espanol, or Francais.
Display U.S. or Metric? Pressing the STEP button when in this display selects US or Metric. The overhead console and instrument panel displays will be in the selected units. Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h).
Remote Linked T o Memory? (A vailable with Memory Seat Only) When this featur e is selected the memory seat, mirr or , and radio settings will return to the memory set position when the remote keyless entry “Unlock” button is pressed.
Illuminated Approach? When this feature is selected the driver can choose, when entering the vehicle, to have the headlamps come on for 30, 60, or 90 seconds, or not come on at all. Pressing the STEP button when in this display will select 30, 60, 90, or OFF .
Service Interval Gasoline Models — If Equipped When this feature is selected, a service interval between 2,000 (3 200 km) and 6,000 miles (10 000 km) in 500 mile (800 km) increments may be selected.
LINK TO MEMORY is set to YES) when the remote keyless entry transmitter is used to unlock the door . For more information, refer to “Easy Entry/Exit Seat — Driver Memory Seat” in Section 3 of this manual.
W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
T rip Computer This feature, located in the instrument cluster , displays the following information when the display is in the “Compass/T emperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-T rip Computer displays.
Reset Button Press the RESET button to reset the display you are in. Press and hold the RESET button (for 2 seconds) to reset all of the displays. A verage Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds.
Elapsed T ime Shows the accumulated ignition ON time since the last reset. T ire Pressure Display — If Equipped Shows the current pressure of all 4 road tires. NOTE: T ires heat up during normal driving conditions. Heat will cause the tir e pr essure to incr ease fr om 2 to 6 psi (14 to 41 kPa) during normal driving conditions.
NOTE: T o ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. Refer to V ariance Map. T o Put Into a Calibration Mode Start the engine and leave the transmission in the P (Park) position.
T o set the variance: T urn the ignition ON and set the display to “Compass/T emperatur e.” Pr ess the C/T but- ton for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the STEP button for 1 second to select the new variance zone and press the RESET button to resume normal operation.
T wo T ypes of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary ... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound.
SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SA TELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERT AINMENT SYSTEMS (VES) CAP ABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Mode Button (Radio Mode) Press the mode button r epeatedly to select between the CD player , Satellite Radio, or V ehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
T ime Button Press the time button and the time of day will be displayed for 5 seconds. Clock Setting Procedure 1. Pr ess and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une / Audio control. 3. After the hours are adjusted, press the right side T une / Audio contr ol to set the minutes.
Press the rotary TUNE control a third time and TREBLE will display . T urn the TUNE control to the right or left to increase or decrease the T reble tones. Press the rotary TUNE control a fourth time and BAL- ANCE will display . T urn the TUNE contr ol to the right or left to adjust the sound level from the right or left side speakers.
Jazz Jazz News News Nostalgia Nostalgia Oldies Oldies Personality Personality Public Public Rhythm and Blues Rhythm_and_Blues Religious Music Religious_Music Religious T alk Religious_T alk Rock Rock .
Y ou may add a second station to each push-button by repeating the above procedur e with this exception: Press the SET/DIR button twice and SET 2 will show in the display window .
CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corr esponding number where the CD is being loaded. The radio will display PLEASE W AIT and prompt when to INSER T DISC. After the radio displays ⬙ LOAD DISC ⬙ insert the CD into the player .
TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display . R W/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed.
Notes On Playing MP3 Files The radio can play MP3 files, however , acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc T ypes) The MP3 file recor ding media supported by the radio are CD-ROM, CD-R and CD-R W .
Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
ID3 T ag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files ar e not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
LOAD/EJECT Button (CD Mode for MP3 Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corr esponding number where the CD is being loaded. The radio will display PLEASE W AIT and prompt when to INSER T DISC. After the radio displays ⬙ LOAD DISC ⬙ insert the CD into the player .
Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. R W/FF (CD Mode for MP3 Play) Press the FF side of the button to move forward through the MP3 selection.
SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SA TELLITE RADIO AND HANDS FREE PHONE CAP ABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Mode Button (Radio Mode) Press the mode button r epeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Clock Setting Procedure 1. Pr ess and hold the time button until the hours blink. 2. Adjust the hours by turning the right side T une/ Audio control. 3. After the hours are adjusted, press the right side T une/Audio control to set the minutes. The minutes will begin to blink.
Press the rotary TUNE contr ol a fourth time and BAL will display . T urn the TUNE control to the right or left to adjust the sound level fr om the right or left side speakers.
Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display .
SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player , cassette player , or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day . The time of day will display for 5 seconds.
Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification,.
1. At the Main Menu screen, highlight “Clock Setup” and pr ess ENTER OR press and hold for 3 seconds the TIME button on the unit’s faceplate. The Clock Setup screen appears. 2. T o show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER.
2. T o incr ease the clock by hours, make sure “HR +” is highlighted and press ENTER. Press ENTER again to increase the clock by another hour . Y ou will see on the “User Defined T ime” display the number of hours you have increased the clock by .
1. When you are at an audio screen, quickly pr ess the TIME button on the navigation faceplate. 2. In this example the large clock appears on the screen. 3. T o switch the clock to the small clock, quickly press TIME again. 4. T o toggle back to the large clock, simply press TIME.
VIDEO ENTERT AINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (V ideo Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two head- sets.
The LCD screen is located on the headliner behind the front seats. SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver br oadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satel- lite Radio.
sports, news, entertainment, and programming for chil- dren, dir ectly from its satellites and br oadcasting studios. System Activation T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .
ESN/SID Access with RAQ Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds.
appear in the display between each channel change. Pr ess the SCAN button a second time to stop the search. NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing.
Satellite Antenna T o ensure optimum reception on vehicles available with a luggage rack, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased perfor- mance.
The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume.
The center button on the left side r ocker switch has no function for a single disc CD player . However , when a multiple disc CD player is equipped on the vehicle, the center button will select the next available CD in the player . CD/DVD DISC MAINTENANCE T o keep the CD/DVD discs in good condition, take the following precautions: 1.
CLIMA TE CONTROLS Manual Air Conditioning and Heating System — If Equipped The controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort contr ols can be set to obtain desir ed interior conditions.
T emperature Control The temperature of air can be selected by rotating the temperature control knob in the center . The coldest tem- perature setting is on the extreme left and the warmest setting on the ex- treme right of the r otation. The knob can be positioned at any point on the dial.
through vents under the front seats. Some airflow is delivered to defrost while in the floor mode so that comfort can be maintained. Bi-Level Air flows both thr ough the outlets located in the instrument panel and those located on the floor .
Slight changes in engine speed or power may be noticed when the air conditioning compr essor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy .
LO AUT O position should be used for front seat occu- pants only . The HI AUTO position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob.
debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • T o provide you with maximum comfort in the auto- matic mode, during cold start-ups the blower fan will remain of f until the engine warms up.
UNDERST ANDING YOUR INSTRUMENT P ANEL 239 4 I n f o r m a t i o n P r o v i d e d b y :.
NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively .
• Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor . Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow .
NOTE: Extended use of recir culation may cause the windows to fog. If the interior of the windows begins to fog, press the “Recirculate” icon button to return to outside air . Some temp./humidity conditions will cause captured interior air to condense on windows and ham- per visibility .
When using the air conditioner in extremely heavy traffic in hot weather especially when towing a trailer , addi- tional engine cooling may be required. If this situation is encountered, operate the transmission in a lower gear to increase engine RPM, coolant flow and fan speed.
Operating Tips Chart 244 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur e ...................... 2 4 9 ▫ Normal Starting — Gasoline Engines ....... 2 4 9 ▫ If Engine Fails T o Start ................. 2 4 9 ▫ Normal Starting — Diesel Engines ......... 2 5 0 䡵 Engine Block Heater — If Equipped .
䡵 Off-Road Driving T ips ................... 2 6 8 ▫ When T o Use 4WD Low Range — If Equipped ......................... 2 6 8 ▫ Driving Through W ater ................. 2 6 8 ▫ Driving In Snow , Mud And Sand .......... 2 7 0 ▫ H i l l C l i m b i n g .
▫ Alignment And Balance ................. 2 9 3 䡵 T ire Chains ........................... 2 9 4 䡵 T ire Rotation Recommendations ............ 2 9 4 䡵 T ire Pressur e Monitor System (TPMS) ........ 2 9 5 ▫ Base System — If Equipped .......
䡵 Fuel Requirements — Diesel ............... 3 1 2 䡵 Adding Fuel .......................... 3 1 3 ▫ Fuel Filler Cap (Gas Cap) ............... 3 1 3 䡵 V ehicle Loading ........................ 3 1 6 ▫ Certification Label ...................
ST ARTING PROCEDURE Start the engine with the selector lever in the N (Neutral) or P (Park) position. Apply the brake before shifting to any driving range. Normal Starting — Gasoline Engines Do not press the accelerator . T urn the ignition key briefly to ST ART position, and release it.
If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor , the normal starting pr ocedure should be repeated. W ARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle.
Starting and Operating Cautions — Diesel Engines W ARNING! NEVER pour fuel or other flammable liquid into the air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . • Running a cold engine at high speeds during driving or idling may damage engine components.
TURBOCHARGER ⬙ COOL DOWN ⬙ CHART Driving Conditions Load T urbocharger T emperature Idle T ime (in minutes) Before Shut Down Stop & Go Empty Cool Less than 1 Stop & Go Medium W arm 1 Highway Speeds Medium W arm 2 City T raffic Max. GCWR W arm 3 Highway Speeds Max.
ENGINE BLOCK HEA TER — IF EQUIPPED The engine block heater warms engine coolant and per- mits quicker starts in cold weather . Connect the cord to a standard 1 10-1 15 volt AC electrical outlet with grounded, three wire extension cord. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days.
W ARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something.
Gear Ranges NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. If there is a need to restart the engine be sur e to cycle the key to the LOCK position before restarting.
W ARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something.
of the desir ed top gear . For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear , but can shift down to 2 (second) or 1 (first), when needed.
Overdrive Operation The automatic transmission includes an electronically controlled Over drive (5th gear for 3.7L engine, 4th and 5th gears for 4.7L and 5.
In high ambient temperatur es with sustained high engine speed and load, an upshift followed shortly thereafter by a downshift may occur . This is a normal part of the overheat pr otection strategy when operating in the “T ow/Haul” mode.
T ransmission Limp Home Mode T ransmission function is monitored for abnormal condi- tions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.
NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold.
five rocking-motion cycles. This will minimize overheat- ing and r educe the risk of transmission failure during prolonged efforts to free a stuck vehicle. CAUTION! When “rocking” a stuck vehicle by moving between “First” and R (Reverse), do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.
percent of engine torque to the rear axle. When speed differ ences ar e increased between the fr ont and rear drive shafts, the transfer case can transmit up to 100 percent of available engine torque to the front or rear drive shafts.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.
LOW Indicator Lamp” in the instrument cluster will begin to flash and remain on solid when the shift is complete. Release the T -handle. NOTE: If shift conditions/interlocks are not met, or a transf.
LOW Indicator Lamp” in the instr ument cluster will flash and go out when the shift is complete. Release the T -handle. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperatur e protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic V ehicle Information Cen- ter).
5. Repeat Steps 1– 4 to shift out of Neutral. NOTE: If shift conditions/interlocks are not met, a “CHECK SHIFT PROCEDURES” message will flash fr om the EVIC (Electr onic V ehicle Information Center). Refer to “Electronic V ehicle Information Center (EVIC)” in Section 4 of this manual.
operation is similar . Follow the Quadra-T rac II 威 transfer case shifting information, preceding this section, for shifting this system. ON-ROAD DRIVING TIPS Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-r oad applications.
CAUTION! When driving through water , do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be covered by the new vehicle limited warranty .
Driving In Snow , Mud and Sand In heavy snow , when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4WD LOW if necessary . Refer to “Four-Wheel Drive Operation” in this section.
Remember , never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease of f the accelerator and maintain headway by turning the fr ont wheels slowly . This may pr ovide a fresh “bite” into the surface and will usually pr ovide traction to complete the climb.
• After extended operation in mud, sand, water , or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. W ARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.
Be sure the parking brake is firmly set when parked and the gear shift lever is in the P (Park) position. When parking on a hill, you should apply the parking brake before placing the gear shift lever in P (Park), otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of P (Park).
When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle.
W ARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop.
CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed after -market radios or tele- phones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be hear d.
build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability , and control. • After going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action.
CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur . MUL TI DISPLACEMENT SYSTEM (MDS) - 5.
• European Metric tire sizing is based on European design standards. T ires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙ P ⬙ is absent from this tire size designation. Example: 215/65R15 96H • L T (Light T ruck)-Metric tire sizing is based on U.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however , the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: The pr oper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tir e must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the load.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle.
286 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, af fect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tr ead life r esulting in a need for earlier tir e r eplacement. Under inflation also increases tire r olling resistance and results in higher fuel consump- tion.
check tire pressur e. Do not make a visual judgement when determining pr oper inflation. Radial tir es may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped.
Tire Pressures for High Speed Operation The manufactur er advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressur e is very important.
W ARNING! Fast spinning tires can be dangerous. Forces gener - ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed.
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear . TIRE CHAINS Certain models have suf ficient tire-to-body clearance to allow use of tire chains.
Follow the r ecommended tire r otation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corr ected prior to r otation being per- formed.
decrease. T ire pr essure should always be set based on cold inflation tire pressur e. This is defined as the tire pressur e after a vehicle has not been driven for more than 3 hours - and in outside ambient temperature.
T elltale Light” will turn OFF only after the tires have been inflated to the vehicle’s recommended cold tire pressure value. NOTE: Seasonal temperature changes will affect tire pressur e, and the TPM system will monitor the actual tir e pressur e in the tire.
will automatically update and the “T ire Pr essure Moni- toring Light” will extinguish once the updated tire pres- sures have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information.
will update automatically , and the “T ire Pressure Moni- toring T elltale Light” will be OFF as long as none of the road tires are below the low pressure warning threshold. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information.
Under-inflation also r educes fuel efficiency and tir e tread life, and may affect the vehicle’s handling and stopping ability . • The TPMS is not a substitute for proper tire mainte- nance, and i.
T ire Pressure Monitoring Low Pressure W arnings The “T ire Pressure Monitoring T elltale Light” will illuminate in the instrument cluster , and an au- dible chime will be activated when one or more of the four active road tire pressur es are low .
Should a low tir e condition occur on any of the four active r oad tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure.
If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “T ire Pressur e Monitoring T elltale Light” will no longer flash, the ⬙ SER VICE TIRE PRESS. SYSTEM ⬙ text message will no longer display , and a pressur e value will be displayed instead of dashes.
T elltale Light” will be OFF as long as no r oad tire(s) are below the low pressure warning threshold. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
Under-inflation also r educes fuel efficiency and tir e tread life, and may affect the vehicle’s handling and stopping ability . • The TPMS is not a substitute for proper tire mainte- nance, and i.
5.7L Engines (If Equipped) The 5.7L engine is designed to meet all emissions regulations and provide satisfac- tory fuel economy and performance when using high quality unleaded gasoline hav- ing an octane range of 87 to 89. The manu- facturer recommends the use of 89 octane for optimum performance.
The manufactur er supports the use of r eformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE.
It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformu- lated gasoline. Materials Added T o Fuel All gasoline sold in the United States is required to contain effective detergent additives.
Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. W ARNING! Ethanol vapors are extremely flammable and could cause serious personal injury .
NOTE: When the ambient temperature is above 90°F (32°C), you may experience hard starting and rough idle following start up even if the above r ecommendations ar e followed.
Maintenance If you operate the vehicle using E-85 fuel, follow “Main- tenance Schedule B.” Refer to Section 8 of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability .
ADDING FUEL CAUTION! DO NOT put gasoline in your diesel vehicle (if equipped). If you accidentally put gasoline in your vehicle, DO NOT start the engine. This will cause damage to the fuel system. Have the fuel system flushed. Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door , on the driver’s side of the vehicle.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the MIL (Malfunction Indica- tor Light) to illuminate, due to fuel vapors escaping from the system.
NOTE: T ighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is pr operly tightened. If the gas cap is not tighten properly , the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
W ARNING! • Never add fuel when the engine is running. • Never have any smoking materials lit in or near the vehicle when the fuel cap is removed or the tank filled.
Each axle GA WR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by pur chasers for in- creased durability does not necessarily increase the vehi- cle’s GVWR.
or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sur e that the weight is distributed equally .
Gross T railer W eight (GTW) The gr oss trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙ loaded and r eady for operation ⬙ condition.
that typically pr ovides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. W eight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle.
W eight Distributing Hitch System Improper Adjustment of W eight Distributing System ST ARTING AND OPERA TING 321 5 I n f o r m a t i o n P r o v i d e d b y :.
T railer Hitch Classification Y our vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional T railer T ow Prep Package.
T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ T ransmission Model GCWR (Gross Com- bined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.
5.7L/Automatic 4x2 12,200 lbs (5 534 kg) 64 Sq. Ft. (5.95 square meters) 7,400 lbs (3 357 kg) 740 lbs (336 kg) 5.7L/Automatic (Overland) 4x2 12,200 lbs (5 534 kg) 64 Sq. Ft. (5.95 square meters) 7,395 lbs (3 354 kg) 740 lbs (336 kg) 5.7L/Automatic 4x4 12,200 lbs (5 534 kg) 64 Sq.
T railer and T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle.
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
loss of contr ol, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chas- sis structur e or tires. • Safety chains must always be used between your vehicle and trailer . Always connect the chains to the hook retainers of the vehicle hitch.
T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressur es are essential to the safe and satisfactory operation of your vehicle. Refer to the T ires–General Information section of this manual on T ire Pressur es for proper tire inflation procedur es.
CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal ef- fort, and longer stopping distances.
T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. 4 - Pin Connector 7- Pin Connector 330 ST ARTING AND OPERA TING I n f .
T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the ”T ow/ Haul” mode (if equipped) or a lower gear range should be selected.
− Air Conditioning T urn off temporarily . − Refer to Cooling System Operating information in the Maintenance section of this manual for more informa- tion. RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) T owing – 2WD Models Recreational towing is allowed ONL Y if the driveshaft is removed.
Shifting Into Neutral (N) Use the following procedure to prepar e your vehicle for recr eational towing. CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (Neutral) before recreational towing to prevent damage to internal parts.
5. Start engine. 6. Shift transmission into D (Drive). 7. Release brake pedal and ensure that ther e is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into P (Park). 10. Place the ignition key in the OFF position, and remove key . 1 1.
Hold down N (Neutral) “pin” switch (with a pen, etc.) for 4 seconds until the LED lamp by the switch starts to blink indicating shift in progr ess. Lamp will stop blinking (go out) when shift is complete. The “4WD SYSTEM IN NEUTRAL” message will no longer be displayed on the EVIC (Electronic V ehicle Information Center).
NOTE: When shifting out of transfer case N (Neutral), turning the engine OFF may be requir ed to avoid gear clash. W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flashers ................. 3 3 8 䡵 If Y our Engine Overheats ................. 3 3 8 䡵 Jacking And T ire Changing ................ 3 3 9 ▫ Jack Location ........................ 3 4 0 ▫ Spare T ire Stowage .
HAZARD W ARNING FLASHERS Y our vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently . Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle.
removes this heat. Y ou can also turn the T emperature Control to maximum heat, the Mode Contr ol to floor , and the Fan Contr ol to High. This allows the heater core to act as a supplement to the radiator and aids in r emoving heat from the engine cooling system.
Jack Location The scissor-type jack and tire changing tools are located in the passenger side compartment behind the second row seat. Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. T o r emove or stow the spare, use the jack handle to rotate the “spar e tire drive” nut.
Spare Tire Removal Fit the jack handle extension over the drive nut. Use the Lug W rench to rotate the nut counter clockwise until the spare is on the ground with enough slack in the cable to allow to pull the tire out from under the vehicle. CAUTION! The winch mechanism is designed for use with the jack extension tube only .
Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in P (Park). T urn OFF the ignition. W ARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
4. Locate the jack as shown. For the fr ont axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle.
5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability . W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to it’s fully closed position.
JUMP ST ARTING If the vehicle has a dischar ged battery , booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly , so follow this procedur e carefully .
2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, place the transmission in P (Park), and turn the ignition OFF . 3. T urn off the heater , radio, and all unnecessary electri- cal loads.
W ARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery .
W ARNING! • Y ou should not try to start your vehicle by push- ing or towing. • Do not connect the cable to the negative post of the discharge battery . The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are be- low freezing point, electrolyte in a discharged battery may freeze.
W ARNING! Stand clear of vehicles when pulling with tow hooks. T ow straps and chains may break, causing serious injury . TOWING A DISABLED VEHICLE 2WD Models Only Provided the transmission is operable, tow only in N (Neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km).
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L ............... 3 5 4 䡵 Engine Compartment – 4.7L ............... 3 5 5 䡵 Engine Compartment – 5.7L ............... 3 5 6 䡵 Engine Compartment – 3.0L Diesel .......... 3 5 7 䡵 Onboard Diagnostic System — OBD II .
▫ Maintenance-Free Battery ................ 3 7 0 ▫ Air Conditioner Maintenance ............. 3 7 1 ▫ Power Steering Fluid Check .............. 3 7 2 ▫ Body Lubrication ..................... 3 7 4 ▫ W indshield W iper Blades ................
▫ F r o n t F o g L i g h t ...................... 4 0 4 ▫ Rear T ail, Stop, T urn Signal, And Back-Up Lights ....................... 4 0 4 ▫ Center High Mounted Stop Light (CHMSL) . . . 406 䡵 Fluids And Capacities ................... 4 0 7 䡵 Fluids, Lubricants, And Genuine Parts .
ENGINE COMP ARTMENT – 3.7L 354 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ENGINE COMP ARTMENT – 4.7L MAINT AINING YOUR VEHICLE 355 7 I n f o r m a t i o n P r o v i d e d b y :.
ENGINE COMP ARTMENT – 5.7L 356 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ENGINE COMP ARTMENT – 3.0L DIESEL MAINT AINING YOUR VEHICLE 357 7 I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
manual). T ighten the gas cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is pr operly tightened. This message may be temporarily overridden by pr essing either the C/T , STEP , or MENU buttons. However , after one minute of no customer interaction, the EVIC will display again the “CHECK GASCAP” message.
replacement. If the OBD system should be determined not ready for the I/M test, your vehicle may fail the test. Y our vehicle has a simple ignition key actuated test which you can use prior to going to the test station. T o check if your vehicle’s OBD system is r eady , you must do the following: 1.
during normal vehicle operation, you should have your vehicle serviced befor e going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running.
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
Change Engine Oil Road conditions as well as your kind of driving af fect the interval at which your oil should be changed. Check the following to determine if any apply to you: • Day or night tempe.
Material Standar d MS-6395. Use Mopar 威 or an equiva- lent oil meeting the specification MS-6395. Engine Oil Selection - Diesel Engines For best performance and maximum protection for all engines un.
For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Engine Oil V iscosity (3.
indiscriminately discarded, can present a problem to the environment. Contact your local authorized dealer , ser- vice station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced with a new filter at every oil change.
Spark Plugs Spark plugs must fire properly to assure engine perfor - mance and emission control. New spark plugs should be installed at the specified mileage.
Catalytic Converter The catalytic converter requires the use of unleaded fuel only . Leaded gasoline will destroy the ef fectiveness of the converter as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Check ventilation hose for indication of damage or plugging deposits. Replace if necessary . Maintenance-Free Battery Y our vehicle is equipped with a maintenance-fr ee battery . Y ou will never have to add water , nor is periodic main- tenance requir ed.
T o determine the battery charge, check the battery test indicator (if equipped) on top of the battery . Refer to the illustration. CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at this time. W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
CAUTION! Do not use Automatic T ransmission Fluid (A TF) or other types of power steering fluids when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid. Checking the power steering fluid level at a defined service interval is not required.
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to pr otect against rust and wear .
The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment (on the driver side), and should be checked for fluid level at regular intervals.
W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to Exhaust Gas in the Safety T ips section of this manual.
for any accumulation of bugs, leaves, etc. If dirty , clean by gently spraying water from a garden hose vertically down the face of the condenser . Check the engine cooling system hoses for brittle rubber , cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator .
CAUTION! Mixing of antifreeze/coolant other than the specified HOA T antifreeze/coolant may result in decreased corrosion protection and engine damage. If a non- HOA T antifreeze/coolant is introduced into the cool- ing system in an emergency , it should be replaced with the specified antifreeze/coolant as soon as pos- sible.
Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
Disposal of Used Engine Coolant Used ethylene glycol-based antifreeze/coolant is a regu- lated substance r equiring proper disposal. Check with your local authorities to determine the disposal rules for your community .
If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check antifreeze/coolant fr eeze point in the radiator and in the coolant r ecovery bottle.
Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose rout- ing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear . Insure nylon tubing in these ar eas has not melted or collapsed.
Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and me- chanical damage. Hard and brittle rubber , cracking, tears, cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber .
Brake Master Cylinder — Brake Fluid Level Check The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir .
CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Front/Rear Axle Fluid Front Axle Fluid Level Check Lubricant should be to the bottom of the oil fill hole. Rear Axle Fluid Level Check Lubricant should be 1/2” (1 cm) below the oil fill hole.
CAUTION! When installing plugs, do not overtighten. Y ou could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
Check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. T o check the automatic transmission fluid level properly , the following procedur e must be used: 1.
CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading.
Service Manual. Also check for accumulations of vegeta- tion or brush that could become a fire hazard, or conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts.
W ashing • W ash your vehicle r egularly . Always wash your ve- hicle in the shade using Mopar 威 Car W ash or a mild car wash soap, and rinse the panels completely with clear water . • If insects, tar , or other similar deposits have accumu- lated on your vehicle, use Mopar 威 Super Kleen Bug and T ar Remover to remove.
• If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle r epaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner . • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc.
Y our leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be r emoved pr omptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar 威 T otal Clean.
equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror , spray cleaner on the towel or rag that you are using.
Cavity Cartridge Fuse Mini Fuse Description 1 30 Amp Green Audio Amp (B+) 2 15 Amp Blue Sunroof (B+) Cavity Cartridge Fuse Mini Fuse Description 3 10 Amp Red Htd Mirror (EBL) 4 20 Amp Y ellow Rr Pwr O.
Cavity Cartridge Fuse Mini Fuse Description 10 10 Amp Red Final Drive Control Module (FDCM), Heater V entilation, Air Conditioning (HV AC), Switch Bank, T ransfer Case Switch, O/H, Heater V entila- tion, Air Conditioning (HV AC) Relay , Rear Park Assist 1 1 Spar e (B+) 12 10 Amp Red Door Mods, Mem.
Cavity Cartridge Fuse Mini Fuse Description 21 Spare (Acc De- lay) 22 15 Amp Blue Rear W iper (B+) 24 10 Amp Red Power Distribution Center (PDC) Relays, Final Drive Control Module (FDCM), Front Control Module (FCM) (R/S), A580 (R/S) 25 10 Amp Red Shifter Assy (BTSI), T rans.
Cavity Cartridge Fuse Mini Fuse Description 2 30 Amp Pink Power Outlets 3 30 Amp Pink Rr W iper/Ign R/O 4 30 Amp Pink ABS Pump 5 50 Amp Red Cabin Htr 1 (Diesel Only) 6 50 Amp Red Auto Shut Down (ASD) .
Cavity Cartridge Fuse Mini Fuse Description 18 20 Amp Y ellow EA TX/AC Clutch 19 20 Amp Y ellow Ign Sw 20 20 Amp Y ellow PCM Batt (Gasoline Only) 21 30 Amp Green ABS V alves 22 20 Amp Y ellow T -T ow .
Underhood Fuses (Integrated Power Module) Cavity Cartridge Fuse Mini Fuse Description 8 10 Amp Red Lt Park Lamps Cavity Cartridge Fuse Mini Fuse Description 9 10 Amp Red T railer-T ow Park Lamps 10 10.
Cavity Cartridge Fuse Mini Fuse Description 18 20 Amp Y ellow Front Control Module (FCM) Batt #1 19 20 Amp Y ellow Lt T railer-T ow Stop/ T urn 20 20 Amp Y ellow Front Control Module (FCM) Batt #3 21 .
in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT BULBS Interior Lights Bulb T ype Glove Box Light ....................
2BULB REPLACEMENT Head Light 1. Open the hood. 2. Remove the headlamp cover . 3. T urn the low or high beam bulb 1/4 turn counter clockwise to remove from housing. 4. Disconnect the electrical connector and replace the bulb. CAUTION! Do not touch the new bulb with your fingers.
Front T urn Signal 1. Open the hood. 2. Remove the headlamp cover . 3. T urn the turn signal bulb 1/4 turn counter clockwise to remove from housing. 4.
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Light 1. Reach behind the front fascia from under the vehicle.
3. Squeeze the socket assembly tabs to r emove it from the housing. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly .
Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. T wist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 3.7/4.7/5.7L Gasoline Engines 21 Gallons 79 Liters 3.0L Diesel Engine 22 Gallons 83 Liters Engine Oil with Filter 3.7 Liter Engine (SAE 5W -20, API Certified) 5 Qts 4.7 Liters 4.7 Liter Engine (SAE 5W -20, API Certified) 6 Qts 5.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) Engine Oil (3.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid T ransfer Case (3.7L Engine Only) Mopar 威 A TF+4 Automatic T ransmission Fl.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 4 1 2 䡵 Maintenance Schedules ................... 4 1 2 ▫ Schedule “B” ........................ 4 1 5 ▫ Schedule “A” ........................ 4 2 7 䡵 Maintenance Schedules — Diesel Engines .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system.
• T axi, police, or delivery service (commercial service) • Off-r oad or desert driving NOTE: Most vehicles are operated under the conditions listed for Schedule “B.
Once a Month • Check the tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of the coolant reservoir , brake master cylinder , and transmission, and add as needed.
Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Check spare tire for proper pressur e and correct stowage.
Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage.
Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Check spare tire for proper pressur e and correct stowage.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change the engine oil and engine oil filter , if not replaced at 3 months. XXX X X Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage.
Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (1 15 000) (120 000) (125 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Check spare tire for proper pressur e and correct stowage.
Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage.
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Check spare tire for proper pressur e and correct stowage.
Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter , if not replaced at 3 months. XXX X X Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage.
Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage.
Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage.
Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all r e- ceipts. 〫 This maintenance is recommended by the manufac- turer to the owner , but is not required to maintain emissions warranty . * This maintenance is not requir ed if the belt was previously replaced.
Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change the engine oil and engine oil filter . X X X X X Rotate the tires. X X X X X Check spare tire for proper pressur e and correct stowage.
Miles 36,000 42,000 48,000 54, 000 (Kilometers) (60 000) (70 000) (80 000) (90 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage.
Miles 60,000 66,000 72,000 78,000 (Kilometers) (100 000) (1 10 000) (120 000) (130 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage.
Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage.
Miles 108,000 1 14,000 120,000 126,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) [Months] [108] [114] [120] [126] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage.
Miles 132,000 138,000 144,000 150,000 (Kilometers) (220 000) (230 000) (240 000) (250 000) [Months] [132] [138] [144] [150] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage.
Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all r e- ceipts. 〫 This maintenance is recommended by the manufac- turer to the owner , but is not required to maintain emissions warranty . * This maintenance is not requir ed if the belt was previously replaced.
NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” Second is Schedule “A” . It is for vehicles that are not operated under any of the conditions listed under Sched- ule “B.” Use the schedule that best describes your driving condi- tions.
At Each Oil Change • Change the engine oil filter . • Inspect the exhaust system. • Inspect brake hoses. • Check the engine coolant/anti-freeze level, hoses, and clamps. • Inspect engine accessory drive belts. Replace as neces- sary . • Inspect for the pr esence of water in the fuel filter/ water separator unit.
Schedule “B” — Diesel Engines Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 6,250 12,500 18,750 25,000 31,250 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) Change the engine oil and engine oil filter . X X X X X Rotate the tires. X X X Check spare tire for proper pressur e and correct stowage. X X XXX Inspect the engine air filter element.
Miles 37,500 43,750 50,000 56,250 62,500 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) Change the engine oil and engine oil filter . X X X X X Rotate the tires. X X Check spare tire for proper pressur e and correct stowage. X X XXX Inspect the engine air filter element.
Miles 68,750 75,000 81,250 87,500 93,750 100,000 (Kilometers) (1 10 000) (120 000) (130 000) (140 000) (150 000) (160 000) Change the engine oil and engine oil filter . X X X X X X Rotate the tires. X X X Check spare tire for proper pressur e and cor- rect stowage.
〫 Applies only if vehicle is used for frequent trailer towing, or fleet/commercial service. † The replacement of such component is requested when there is superficial wear , bearing clearance, or evident grease leak. Inspection and service should be performed anytime a malfunction is observed or suspected.
Schedule “A” Miles 12,500 25,000 37,500 50,000 (Kilometers) (20 000) (40 000) (60 000) (80 000) Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage. X X X X Inspect the engine air filter element.
Miles 62,500 75,000 87,500 100,000 (Kilometers) (100 000) (120 000) (140 000) (160 000) Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Check spare tire for proper pressur e and correct stowage. X X X X Inspect the engine air filter element.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y o u r V e h i c l e .......................... 4 4 4 ▫ Prepar e For The Appointment ............ 4 4 4 ▫ Prepar e A List ........................ 4 4 4 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner . This is why you should always talk to your dealer’s service manager first.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer .
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .
on specified government test surfaces of asphalt and concrete. A tir e marked C may have poor traction perfor- mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
ABS (Anti-Lock Brake System) ............ 176,274 Adding Fuel ........................... 3 1 3 Adding W asher Fluid ..................... 1 6 5 Adjustable Pedals ....................... 1 2 4 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 367 Air Conditioner Maintenance .
Autostick ............................. 2 5 6 Auxiliary Electrical Outlet (Power Outlet) ...... 1 5 6 Auxiliary Power Outlet ................... 1 5 6 Battery ............................... 3 7 0 Emergency Starting ..................... 3 4 6 Keyless T ransmitter Replacement (RKE) .
C a r g o L i g h t ............................ 1 5 9 Cargo Load Floor ........................ 1 6 3 Cargo T ie-Downs ........................ 1 6 1 Catalytic Converter ...................... 3 6 8 Caution, Exhaust Gas ..................... 1 4 7 CD (Compact Disc) Player .
C r u i s e L i g h t ........................... 1 8 1 C u p H o l d e r ............................ 1 5 8 Customer Assistance ..................... 4 4 4 Data Recorder , Event ...................... 5 2 Daytime Running Lights ................... 1 1 6 Dealer Service .
Electronic V ehicle Information Center (EVIC) ....................... 180,183 Emergency , In Case of Freeing V ehicle When Stuck ............... 2 6 1 Hazard W arning Flasher ................. 3 3 8 Jacking ............................. 3 3 9 Jump Starting .
Filters Air Cleaner .......................... 3 6 7 Engine Oil ........................... 3 6 6 Engine Oil Disposal .................... 3 6 5 F i n i s h C a r e ............................ 3 9 0 Flashers .............................. 3 3 8 Hazard W arning .
Gauge .............................. 1 8 1 Hoses .............................. 3 8 2 Materials Added ....................... 3 0 8 Octane Rating ...................... 305,306 Requirements ...................... 312,407 System Hoses .................
Heated Mirrors .......................... 7 6 Heated Seats ........................... 1 0 2 Heater , Engine Block ..................... 2 5 3 High Beam Indicator ..................... 1 7 5 High Beam/Low Beam Select (Dimmer) Switch . . 1 18 Hitches T r a i l e r T o w i n g .
Key , Replacement ........................ 1 7 Key , Sentry (Immobilizer) ................... 1 5 Key-In Reminder ......................... 1 5 Keyless Entry System ...................... 1 9 Keys ................................. 1 4 Lap/Shoulder Belts .
Headlight Switch ...................... 1 1 4 Headlights ........................... 4 0 2 Headlights On W ith W ipers ............... 1 1 4 High Beam Indicator .................... 1 7 5 Illuminated Entry ....................... 1 9 Instrument Cluster .
Lower Anchors and T ether for CHildren (LA TCH) ............................ 5 8 , 6 0 Lubrication, Body ....................... 3 7 4 Luggage Rack (Roof Rack) ................. 1 6 6 Lumbar Support ........................ 1 0 1 Maintenance Free Battery .
New V ehicle Break-In Period ................ 6 4 Occupant Restraints ....................... 3 4 Octane Rating, Gasoline (Fuel) ............ 305,306 Odometer .......................... 180,181 T r i p ................................ 1 8 0 Off-Pavement Driving (Off-Road) .
Pets, T ransporting ........................ 6 4 Phone, Cellular .......................... 7 7 Phone, Hands-Free (UConnect™) ............. 7 7 Placard, T ire and Loading Information ......... 2 8 3 P o l i s h i n g a n d W a x i n g ..............
Rear W iper/W asher ...................... 1 6 4 Rearview Mirrors ........................ 7 2 Reclining Front Seats ..................... 1 0 0 Recorder , Event Data ...................... 5 2 Recreational T owing ...................... 3 3 2 Shifting into T ransfer Case Neutral (N) .
Inspection ............................ 6 5 Maintenance ........................ 6 5 , 3 9 3 Pretensioners .......................... 4 1 Reminder ............................ 1 8 1 Shoulder Belt Anchorage .................. 4 0 Seats ................
O i l .............................. 363,364 Speed Control (Cruise Control) .............. 1 2 6 Speedometer ........................... 1 7 5 Starting ............................... 2 4 9 Automatic T ransmission ................. 2 4 9 Cold W eather .
T i r e s ............................ 6 6 , 287,449 Air Pressur e .......................... 2 8 8 Alignment and Balance .................. 2 9 3 Chains .............................. 2 9 4 Changing ............................ 3 3 9 General Information .
T railer and T ongue W eight ................ 3 2 5 W i r i n g .............................. 3 2 9 T r a i l e r T o w i n g G u i d e ..................... 3 2 3 T r a i l e r W e i g h t .......................... 3 2 3 T ransfer Case ............
W ashers, W indshield .................. 120,374 W ashing V ehicle ......................... 3 9 0 W a x i n g a n d P o l i s h i n g ..................... 3 9 0 Wheel Alignment and Balance ............... 2 9 3 Wheel and Wheel T rim ................
NOTES I n f o r m a t i o n P r o v i d e d b y :.
NOTES I n f o r m a t i o n P r o v i d e d b y :.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Jeep Grand Cherokee (2007) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Jeep Grand Cherokee (2007) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Jeep Grand Cherokee (2007), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Jeep Grand Cherokee (2007) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Jeep Grand Cherokee (2007), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Jeep Grand Cherokee (2007).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Jeep Grand Cherokee (2007). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Jeep Grand Cherokee (2007) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
