Manuel d'utilisation / d'entretien du produit J-DREAM II du fabricant Jacuzzi
Aller à la page of 36
J-DREAM II Shower System OWNER’S MANUAL Assembly, Installation & Operating Instructions TM.
IMPORT ANT SAFETY INFORMA TION READ ALL INST ALLA TION INSTRUCTIONS Save These Instructions for Future Use. Owner's Record Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer.
Part I Assembly & Installation Specifications _______________________________________________________________________ 2 General Information ________________________________________________________.
WHIRLPOOL B ATH R J-Dream II Owner's Manual FRONT VIEW PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. SPECIFICATIONS 2 TOP VIEW DIMENSIONS 60" (1524mm)L 42" (1067mm)W 83" (2108mm)H TOTAL WEIGHT/ FLOOR LOADING 833 lb (379 kg) 47.
Read all instructions before beginning assembly and installation. General Assembly Information The J-Dream II shower unit is installed into a niche with the drain towards the left hand side of the unit as you face the shower door. This manual details the assembly, installation and operation.
Electrical requirements Your J-Dream II, as it comes from the factory, requires a GFCI protected 240 VAC 3- wire 20 AMP 50-60 Hz circuit (2 conductor with ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected in that circuit.
J-Dream II Packaging 6 cartons packed together on a wooden crate. Contents of cartons: • Wall Panels • Door Frame • Base/Cover (includes product accessory pack and owners manual) • Back Wall .
J-Dream II Owner's Manual Letters (A) are used in the illustrations of the assembly procedure. 6 FLA T W ASHER 1/4" P AN HEAD SCRE W #10-24 x 3/4 " LO CK NUT 10-24 C W ASHER SCREW B NUT D FLA T HEAD SCRE W M4x10mm SCREW E P AN HEAD SCRE W #12 x 1/2 SCREW F HEX BOL T 1/4-20 x 1.
7 Rough-in W ASHING MACHINE OUTLET BOX CONNECT #8 GAUGE (10mm 2 ) MINIMUM SOLID COPPER BOND WIRE T O THE HOUSE ELECTRICAL P ANEL OR APPROVED LOCAL GROUND. AN APPROVED GROUND MA Y BE AN 8 FOOT LONG GROUND ROD (3 METER LONG EARTH ROD), A PLA TE ELECTRODE, OR OTHER ACCEPT ABLE BOND.
8 Locate Base to provide assembly access to all sides Remove Base from carton labeled Base/Top . Place Clear Top in carton to prevent damage. (The Clear Top will not be installed until the unit has been fully assembled and plumbed). Position the J-Dream base on the floor so that you have work access to all four sides of the unit during assembly.
9 Drain Fitting (provided with unit) Leave enough flexibility in the waste line to allow the end of the stub-out to be blocked temporarily in a position under flush with the floor surface. This will allow the shower unit to slide across the floor into position without having to lift the shower unit.
10 Attach Seat W alls to Base (J-Dream II with stereo shown) Bolts (8) Nuts (8) G J Align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath.
11 Attach Panel #2 to Seat W all Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open.
12 Attach Panel #3 to Seat W all Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open.
13 Install Back W all Caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the back wall parallel to the pan lip to center the back wall between the seat walls.
B A A. Caulk W asher (10) C Nut (3) D Screw (3) B B Reinstall bolts (4) and washers (4) removed from seat wall and bracket Seat wall attaches to panel #1 and #4 in three places.
15 Attach Brackets to Seat W all Frames and L Bracket to left Angle Bracket J-Dream II Owner's Manual B B A C A 17" 58-3/8" TOP O F FRAME Screw (2) Note: only the left side has this L bracket installed.
Caulk B Screw (3) C W asher (3) Nut (3) D T op View (right side) Notch Side View (right side) B Screw (3) C W asher (3) Nut (3) D T op View (left side) Side View (left side) Notch Caulk 16 Attach Painted Angle Brackets to Panels #1 and #4 Note that each angle bracket has a notch on the top and bottom.
17 Attach Door Frame to Angle Brackets and Base Frame Before proceeding, make sure the seat walls are closed and fastened. See detail B on page 15. Align door frame over tabs on base frame and pan lip. Pan lip is to fit into corner posts of door frame.
18 Attach T op Frame to Door Frame, Back W all and Seat W all Frames Press/tap top frame into door frame, aligning notch in door frame with corner of top of frame while aligning with corners of enclosure. Frame snaps down into door frame and back snaps over back wall.
19 Feed the four hoses and controller cable from the back wall and connect them as shown. The steam hose connection uses a hose clamp while the other hoses use spring clamps that are on the hoses. Also feed the CD/Radio wire bundle to the back wall. (J-Dream II with stereo only.
20 J-Dream II Owner's Manual Use cable ties to attach the CD/Radio wire bundle to the cascade hose. The hoses from valves 1 and 3 and the steam hose are loosely attached to their mounting brackets to allow the slack when connecting them and when the hinged seat wall is swung open (like a door) to access equipment.
21 Connect the hoses routed from the back wall as below (grayed lines are pre-attached). Connect the controller line. The red and black leads in the CD/Radio wire bundle must be hooked up to the corresponding colored leads of the power supply. Connect the speaker leads.
22 Bonding (top left hand side of right hand equipment seat wall) J-Dream II Owner's Manual Connect a #8 guage (10mm 2 ) minimum solid copper bond wire to the house electrical pannel or an approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode or ther acceptable bond location.
1. Make sure electric power is OFF at main breaker. 2. Static test water supply hoses for leaks. 3. Plug power cord into GFCI protected wall outlet. 4. Move the assembled J-Dream II into final position. 5. Connect 2" shower drain (see page 9). 6.
24 Attach Front Panels to Unit Remove this screw before operation Ground Wire Speaker and power leads B An t e nna Wire Rear view of CD/radio Screw (2) T innerman ® Nuts (pre-installed) Front Panel B.
25 Place cover on top of unit. Align notch in cover with the corresponding notch in the top metal frame. J-Dream II Owner's Manual T op Cover.
26 T urn On Electric Power at Main Breaker Operate Unit and Check for Leaks Attach Bottom Front Panel to Unit Enclosure Base Frame Panel V elcro ® V elcro ® Removable Face Panels Use finishing strip material (not provided) to cover gap between J-Dream II and finshed wall.
27 FIGURE 1. CONTROL PANEL AND DISPLAY FIGURE 2. MIXER CONTROL Part II: Operating Instructions CONTROL PANEL System control is provided by the electronic display located inside the shower cabin (see F.
Starting the Hydromassage The J-Dream allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by the combined action of 16 water jets (four sets of 4 ). The action of each group of jets is either alternated or pulsed. To start the hydromassage jets, p ress the JETS button once (Figure 1).
29 Care and Maintenance of SteamPros Maintenance of the Steampros includes flushing and visually inspecting for water leaks. To flush the units: 1. Turn OFF power to the unit. 2. To gain access to the SteamPros, the seat wall (equipment wall) must be swung open.
Printed in the U.S.A. Printed on Recycled Paper PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
31.
32.
Jacuzzi Whirlpool Bath Limited W arranty Shower System Pr oduct WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product (“unit”) who purchases the product for personal or single family use (“user”).
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Jacuzzi J-DREAM II c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Jacuzzi J-DREAM II - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Jacuzzi J-DREAM II, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Jacuzzi J-DREAM II va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Jacuzzi J-DREAM II, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Jacuzzi J-DREAM II.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Jacuzzi J-DREAM II. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Jacuzzi J-DREAM II ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
