Manuel d'utilisation / d'entretien du produit Ranger II Storm Series Ranger II Storm Series MWD/FWD du fabricant Invacare
Aller à la page of 60
Ranger II Storm Series ® Wheelchair s MWD/FWD Ranger II B ASIC Ranger II ST ANDARD Ranger II JR Ranger II 250 SERIES Owner's Operator And Maintenance Manual DEALER: THIS MANUAL MUST BE GIVEN T O THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANU AL AND SA VE FOR FUTURE REFERENCE.
2 W A R N I N G W ARNING WARNING DO NOT OPERA TE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERST ANDING THIS MANUAL. IF YOU ARE UNABLE TO UNDERST AND THE W ARNINGS, CAUTIONS, AND INSTRUCTIONS, CONT A.
3 T ABLE OF CONTENTS T A B L E O F C O N T E N T S TABLE OF CONTENTS The following procedures refer to RANGER II MWD - RANGER II BASIC ,RANGER II ST ANDARD and RANGER II 250 SERIES RANGER II FWD - RANGER II BASIC and RANGER II ST ANDARD and RANGER II 250 Series .
4 SPECIFICA TIONS S P E C I F I C A T I O N S SPECIFICATIONS PERFORMANCE RANGER II BASIC RANGER II 250 SERIES RANGER II ST ANDARD Speed (M.P .H.): 0 to 3.8 0 to 3.6 0 to 4.8 T urning Radius: > 23-inches > 23-inches > 23-inches Range (variable) 4 : 18-22 miles 12-14 miles 18-22 miles v Weight Limitation 5 : 250 lbs.
5 S P E C I F I C A T I O N S SPECIFICA TIONS PERFORMANCE RANGER II BASIC RANGER II 250 SERIES RANGER II ST ANDARD Speed (M.P .H.): 0 to 3.8 0 to 3.6 0 to 4.0 T urning Radius: > 26-inches > 25.8-inches > 26-inches Range (variable) 3 : 17-22 miles 12-14 miles 12-16 miles v Weight Limitation 4 : 250 lbs.
6 SPECIFICATIONS RANGER II FWD - RANGER II JR INTEGRA TED SLING SEA T Seat Width Range: 14-inches Seat Depth Range: 16 to 18-inches - In 1-inch increments (17 and 18-inch by extension) Back Height Ran.
7 This Procedure Includes the Following: Repair or Service Information Operating Information Safety/Handling of Wheelchairs Warning/Caution Label Location - MWD Models Warning/Caution Label Location - FWD Models W ARNING CONTROLLER SETTINGS FOR RANGER II JR Set-up of the Electronic Control Unit is to be per for med ONL Y b y a qualified technician.
8 GENERAL GUIDELINES PROCEDURE 1 GENERAL W ARNINGS (CONTINUED) ELECTRICAL EXTREME care should be exercised when using oxygen in close pr oximity to electric cir cuits.
9 SAFETY/HANDLING OF WHEELCHAIRS “Safety and Handling” of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair .
10 GENERAL GUIDELINES PROCEDURE 1 G E N E R A L G U I D E L I N E S Percentage of Weight Distribution W ARNING DO NOT attempt to r each objects if you have to move forward in the seat or pick them up from the floor by r eaching down between your knees.
11 SEAT WIDTH *14 16 18 20 SEAT DEPTH 16 REAR MIDDLE MIDDLE MIDDLE 17 REAR MIDDLE MIDDLE MIDDLE 18 REAR MIDDLE MIDDLE MIDDLE FACTORY SETTINGS - MOTOR MOUNTING POSITIONS (MOTORS WITH CLUTCHES) SEA T WI.
12 GENERAL GUIDELINES PROCEDURE 1 G E N E R A L G U I D E L I N E S Reaching, Bending - Backward W ARNING DO NOT lean over the top of the back uphol- stery. This will change your center of gravity and may cause you to tip over . Position wheelchair as close as possible to the desired object.
13 W ARNING Power ed Wheelchair Electromagnetic Inter ference (EMI) Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna (sour ce), the EM fields from hand-held radio wave sources (transceivers) are of special concern.
14 WARNING/CAUTION LABEL LOCATION - MWD MODELS (RANGER II BASIC /RANGER II STANDARD /RANGER II 250 SERIES ) CAUTION HIGH BACK CAPTAIN'S SEATS ONLY - Discon- nect limit switch BE- FORE removing seat - damage to seat can occur.
15 1074142 Push Bracket Crossbrace WARNING/CAUTION LABEL LOCATION - FWD MODELS (RANGER II BASIC /RANGER II STANDARD /RANGER II 250 SERIES ) W ARNING Replacement con- t roller MUST be SAME part number . Motor Assembly Controller (Back View) CAUTION Repositioning the motors WILL af fect the stability and/or per f or mance of the wheelchair .
16 WARNING/CAUTION LABEL LOCATION - FWD MODELS (RANGER II JR ) W ARNING Replacement con- t roller MUST be SAME part number . Motor Assembly Controller (Back View) CAUTION Repositioning the motors WILL af fect the stability and/or per f or mance of the wheelchair .
17 GENERAL GUIDELINES PROCEDURE 1 G E N E R A L G U I D E L I N E BATTERY BOX SHIPPING INSERTS REMOVING BATTERY BOX SHIPPING INSERTS (RANGER II 250 SERIES ONLY) (FIGURE 1) NOTE: Wheelchairs ordered with batteries installed have shipping inserts which must be removed before using the wheelchair .
18 This Procedure Includes the Following: Troubleshooting Checking Battery Charge Level Safety Inspection Checklist SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 T R O U B L E S H O O T I N G S A F E .
19 5. Draw up sufficient acid to cover float balls. 6. T ap lightly to remove air bubbles. 7. Number of floating balls indicates charge. NUMBER OF FLOA TING BALLS 0 Discharged 1 25% Charged 2 50% Charged 3 75% Charged 4 100% Charged * 5 Overcharged * Check charging system.
20 PROCEDURE 2 SAFETY INSPECTION/TROUBLESHOOTING T R O U B L E S H O O T I N G S A F E T Y I N S P E C T I O N SAFETY INSPECTION CHECKLIST Initial adjustments should be made to suit personal body structure and preference.
21 F R O N T R I G G I N G S PROCEDURE 3 FRONT RIGGINGS This Procedure Includes the Following: Installing/Removing Footrests Adjusting Footrest Height Replacing Heel Loops Installing/Removing Elevatin.
22 FIGURE 5- INST ALLING/REMOVING ELEV A TING LEGRESTS INSTALLING/REMOVING ELEVATING LEGRESTS (FIGURE 5) NOTE: On RANGER II JR Models, the Elevating Legrests MUST be elevated to install/remove from the wheelchair .
23 F R O N T R I G G I N G S PROCEDURE 3 FRONT RIGGINGS RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6) Raising/Lowering Elevating Legrests 1. Perform one (1) of the following: RAISING - Pull back on the release lever until the leg is at the desired height.
24 Replacing NOTE: Observe the position of the current telescoping front rigging support before removal to ensure correct position of new support assembly . 1. Remove the existing telescoping front rigging sup- port from the wheelchair . 2. Install the new telescoping front rigging support into the wheelchair .
25 F R O N T R I G G I N G S PROCEDURE 3 FRONT RIGGINGS FWD WHEELCHAIRS ONL Y ADJUSTING FOOTBOARD MOUNTING BRACKET ANGLE - FWD MODELS ONLY (FIGURE 10). NOTE: This procedure applies to FWD wheelchair mod- els only . NOTE: Angle availability is limited when the motors are in the forward-most position.
26 PREPARING REMOVABLE FOOTBOARD FOR WHEELCHAIR TRANSPORTATION (FIGURE 12 ) Removing The Removable Footboard Plate 1. Depress the push pins on the two (2) support tubes on the removable footboard plate.
27 This Procedure Includes the Following: Installing/Removing Flip Back Armrests Adjusting Flip Back Armrests Adjusting Captain's Seat Armrests FIGURE 2 - ADJUSTING FLIP BACK ARMRESTS LOCKED (DOW.
28 Positioning Flip Back Armrests for Use 1. Make sure the flip back armrest release lever is in the UP (HORIZONT AL) position. 2. Install the flip back armrest into the front arm socket. 3. Lock flip back armrest by pressing flip back armrest release lever into the DOWN (VERTICAL) position.
29 ADJUSTING CAPTAIN'S SEAT (FIGURE 2) Low Back Captain's Seats 1. Lift up on the release handle and move the back to the desired position. High Back Captain's Seats ANGLE. W ARNING HIGH BACK CAPT AIN'S SEA TS O NL Y - NEVER oper- ate the wheelchair while in any recline position over 114 o RELA TIVE TO THE SEA T FRAME.
30 Seat Upholstery Washer Crossbrace FIGURE 4 - REPLACING SEA T POSITIONING STRAP - INTEGRA TED SLING SEA T MODELS Phillips Screw Seat Positioning Strap REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 3) Removing 1. Turn the adjustment lock lever to release the joystick mounting tube from the armrest.
31 This Procedure Includes the Following: Preparing MKIV Joystick for Use Repositioning MKIV Joystick Disconnecting/Connecting Limit Switch Repositioning Battery Charger Connector Fuse Replacement PREPARING MKIV JOYSTICK FOR USE (FIGURE 1) NOTE: The MKIV joystick is factory installed on the right side of the wheelchair .
32 E L E C T R O N I C S PROCEDURE 6 ELECTRONICS REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 4) NOTE: The following procedure applies to FWD wheel- chairs that are equipped with MKIV controllers ONL Y. 1 . Fold the wheelchair . Refer to TRANSPOR TING RANGER II FWD in PROCEDURE 1 1 of this manual.
33 FIGURE 5 - FUSE REPLACEMENT Fuse Fuse Holder Battery WiringHarness FUSE REPLACEMENT NOTE: Fuse found on battery wiring harness for RANGER II JR only . 1. Remove the front shroud. Refer to REMOVING/IN- ST ALLING THE SHROUDS in PROCEDURE 9 of this manual.
34 REPLACING BATTERY BOX RETAINING STRAP All MWD Models and FWD Model RANGER II JR (FIGURE 1) 1. If necessary , remove the front and rear shrouds. Refer to REMOVING/INST ALLING SHROUDS in PROCE- DURE 9 of this manual. 2. Remove the battery boxes from the wheelchair .
35 Battery T ray Hex Bolt FIGURE 2 - REPLACING BA TTERY BOX RET AINING STRAP - ALL FWD MODELS EXCEPT RANGER II JR All FWD Models Except RANGER II JR (FIGURE 2) 1. I f necessary , remove the front and rear shrouds. Refer to REMOVING/INST ALLING SHROUDS in PROCE- DURE 9 of this manual.
36 W H E E L S PROCEDURE 8 WHEELS ENGAGING/DISENGAGING MOTORS WITH CLUTCHES (FIGURES 1 AND 2) W ARNING DO NOT engage or disengage the clutches until the power is in the OFF position. CAUTION Ensure both clutches are fully engaged BEFORE driving the wheelchair .
37 FIGURE 3 - ENGAGING/DISENGAGING MOTORS WITH MOTOR LOCKS T owards Outside of Wheelchair Motor Locks DISENGAGED (Free Wheel Position) Motor Locks ENGAGED (Drive Position) Dust Cover Locknut Nylon Washer Fork ADJUSTING FORKS (FIGURE 4) 1. Remove the dust cover from the caster headtube.
38 S H R O U D S PROCEDURE 9 SHROUDS This Procedure Includes the Following: Removing/Installing Shrouds REMOVING/INSTALLING SHROUDS MWD Wheelchairs (FIGURE 1) REMOVING FRONT SHROUD. 1. T urn the two (2) 1/4-turn bolts that secure front shroud to the two (2) side shrouds COUNTERCLOCKWISE.
39 FIGURE 1 - REMOVING/INST ALLING SHROUDS - MWD WHEELCHAIRS Front Shroud 1/4-T urn Bolts Rear Storage Compartment Rear Shroud Wheelchair Frame PROCEDURE 9 SHROUDS S H R O U D S NOTE: Side shrouds are exploded away for clarity . There is no need to remove side shrouds.
40 FWD Wheelchairs (FIGURE 2) REMOVING FRONT SHROUD. 1. Unclip the retaining strap securing the front shroud and battery box to the wheelchair . 2. Feed the retaining strap through the front shroud. 3. Remove the front shroud from the wheelchair . INSTALLING FRONT SHROUD.
41 S H R O U D S PROCEDURE 9 SHROUDS FIGURE 2 - REMOVING/INST ALLING SHROUDS - FWD WHEELCHAIRS Front Shroud Rear Shroud 16, 18, and 20-inch wide chairs Wheelchair Frame Retaining Strap Retaining Strap Battery Box Battery T ray Clip Clip Rear Shroud 14-inch wide chairs.
42 PROCEDURE 10 BA TTERIES B A T T E R I E S This Procedure includes the following: Installing/Removing Batteries into/From Battery Boxes Connecting Battery Cables W ARNING Make sure power to the wheelchair is OFF be- fo re p er f or ming this pr ocedure .
43 PROCEDURE 10 BA TTERIES B A T T E R I E S CONNECTING BATTERY CABLES W ARNING NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery ter minal(s)/post(s) at the same time. An electrical short may occur and serious personal injury or damage may occur .
44 PROCEDURE 10 BA TTERIES B A T T E R I E S FIGURE 3 - CONNECTING BA TTERY CABLES - DIRECT MOUNT METHOD Orange Battery T erminal Cap POSITIVE (+) Battery T erminal/ Post U-1 Battery Gray Battery T er.
45 Battery Cable Battery Clamp Cover 2. Install battery clamp covers onto battery cables as follows: (FIGURE 5) A. RED battery clamp cover onto RED battery cable. B. BLACK battery clamp cover onto BLACK bat- tery cable. NOTE: Only one (1) battery cable and battery clamp cover are shown for clarity .
46 9. Install the battery box(es) into the wheelchair . Refer to INST ALLING/REMOVING BA TTER Y BOX(ES) in the PROCEDURE 1 1 - FWD MODELS or PROCE- DURE 12 - MWD MODELS of this manual. NOTE: New Battery(ies) MUST be fully charged BEFORE using, otherwise the life of the battery(ies) will be reduced.
47 FIGURE 1 - TRANSPORTING RANGER II FWD - INTEGRA TED SLING SEA TS This Procedure Includes the Following: Transporting Ranger II FWD When to Charge Batteries Charging Batteries Replacing Batteries In.
48 PROCEDURE 1 1 FWD WHEELCHAIRS F W D W H E E L C H A I R S Refer to INST ALLING/REMOVING BA TTER Y BOXES in this procedure of the manual. FIGURE 2 - TRANSPORTING RANGER II FWD - CAPT AIN'S SEA .
49 PROCEDURE 1 1 FWD WHEELCHAIRS F W D W H E E L C H A I R S B. For Model RANGER II 250 SERIES - the battery charger rate decreases to a "trickle charge". NOTE: If performing the charging procedures indepen- dently , READ and CAREFULL Y follow the individual in- structions for each charger (supplied or purchased).
50 Recommended Battery Types W ARNING The warranty and per fo rmance specifications contained in this manual are based on the use of deep cycle gel cell or sealed lead acid bat- teries. Invacare strongly recommends their use as the power source for this unit.
51 Retaining Strap Clip Battery Connections on Side of Wheelchair Frame Retaining Strap NOTE: Wheelchair Frame not shown for clarity . FIGURE 5 - INST ALLING/REMOVING BA TTERY BOXES ALL MODELS EXCEPT .
52 BATTERY TRAY W ARNING P inch point exists between battery tray and bat- tery bracket. Folding Battery Tray for Transport (FIGURE 7 ) 1. If necessary , remove the front shroud. Refer to REMOV- ING/INST ALLING SHROUDS - FWD WHEELCHAIRS in PROCEDURE 9 of this manual.
53 Mounting Slots Hanger Bracket Battery T ray FIGURE 9 - BA TTER Y TRA Y - FOLDING BA TTER Y T RA Y FOR TRANSPORT Pins Battery T ray Pivot Pins PROCEDURE 1 1 FWD WHEELCHAIRS F W D W H E E L C H A I R.
54 PROCEDURE 12 MWD WHEELCHAIRS M W D W H E E L C H A I R S This Procedure Includes the Following: Transporting Ranger II MWD When to Charge Batteries Charging Batteries Replacing Batteries Installing/Removing Battery Boxes Battery T ray Refer to BA TTER Y TRA Y and INST ALLING/REMOVING BA TTER Y BOXES in this pro- cedure of the manual.
55 Battery Gauge Display (BGD) MKIV- RII JOYSTICK Battery Discharge Indicator (BDI) MKIV X, A OR A+ JOYSTICK FIGURE 3 - WHEN TO CHARGE BA TTERIES NOTE: MKIV X Shown. 2. Remove the Captain's Seat. Refer to REMOVING/ INST ALLING CAPT AIN'S SEA T in PROCEDURE 5 of this manual.
56 CHARGING BATTERIES (FIGURE 4) W ARNING Never attempt to r echarge the batteries by at- taching cables dir ectly to the battery ter minals or clamps. Use the r echarging plug located ei- ther on the side/rear of the wheelchair frame or on the fr ont of the joystick.
57 REPLACING BATTERIES W ARNING Most batteries are not sold with instructions. How- ever , war nings are f r equently noted on the cell caps. Read them car efully, otherwise injury or damage can occur . NOTE: Invacare recommends that both batteries be re- placed if one (1) battery is defective.
58 PROCEDURE 12 MWD WHEELCHAIRS M W D W H E E L C H A I R S 1. Examine battery clamps and terminals for corrosion. 2. If applicable, verify that the plastic caps are in place over the battery cell holes. 3. Cut the tie wraps around the terminal caps/covers.
59 PROCEDURE 12 MWD WHEELCHAIRS M W D W H E E L C H A I R S BATTERY TRAY (FIGURE 7 ) Installing Battery Tray 1. If necessary , remove the shrouds. Refer to REMOV- ING/INST ALLING SHROUDS - MWD WHEEL- CHAIRS in PROCEDURE 9 of this manual. 2. T urn the battery tray slightly to one (1) side.
In vacare C orporation w ww .invacare .com USA Canada Invacar e and Storm Series are register ed trademarks of One Invacare W a y 5970 Chedwo r th W ay Invacare Corporation. Elyria, Ohio USA Mississauga, Ontario Y es, you can. and Ranger II are trademarks of Invacare 44036-2125 L5R 3T9, Canada Cor porat ion.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Invacare Ranger II Storm Series Ranger II Storm Series MWD/FWD ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
