Manuel d'utilisation / d'entretien du produit OCMK78 du fabricant Invacare
Aller à la page of 16
On Chair Mounting Kit Assembly , Installation and Operating Instructions Model Nos. OCMK01 and OCMK78 SA VE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage.
2 INSTALLATION OF THE ON CHAIR MOUNTING KIT BACK MOUNTING HARDWARE (FIGURE 1) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2 twist release clamps.
3 Twist Release Clamps. DETAIL "B" Mark FRONT OF WHEELCHAIR Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Upper J Brackets (Top Edge) Lower .
4 INSTALLING THE BACK L BRACKETS (FIGURE 2) NOTE: When mounting the L brackets to the wood backed ContourU cushion the L brackets may be reversed to allow for greater seat depth adjustments as shown in DETAIL A of FIGURE 2.
5 INSTALLING THE BACK J BRACKETS (FIGURE 3) 1. Position the ContourU back between the back canes to determine the approximate mounting position of the J brackets to obtain the desired depth. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 3.
6 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM BACK (FIGURE 4) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 4. 2. Position the two (2) lower J brackets securely into the two (2) fixed release clamps as shown in FIGURE 4.
7 ADJUSTING THE CONTOUR U BACK DEPTH (FIGURE 5) NOTE: There are six (6) depth adjustments avail- able on the ContourU with a pan back. NOTE: There are twelve (12) depth adjustments available on the ContourU with a wood back.
8 ADJUSTING THE CONTOUR U SEATING SYSTEM BACK ANGLE (FIGURE 6) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same depth. Refer to ADJUSTING THE CONT OUR U SEA TING SYSTEM BACK DEPTH in this instruction sheet. NOTE: The back to seat angle is adjusted by repositioning the top and/or the bottom J brackets.
9 INSTALLATION OF ON CHAIR MOUNTING KIT SEAT MOUNTING HARDWARE (FIGURE 7) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2) twist release clamps.
10 Twist Release Clamps. DETAIL "B" Mark Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Front J Brackets (Front Edge) Rear J Brackets (Rear E.
11 INSTALLING THE SEAT L BRACKETS (FIGURE 8) NOTE: When mounting the L brackets to the wood backed ContourU seat the L brackets may be reversed to allow for a wider range of seat height adjustments and shown in DETAIL A of FIGURE 8.
12 INSTALLING THE SEAT J BRACKETS (FIGURE 9) 1. Position the ContourU seat between the seat rails to determine the approximate mounting position of the J brackets to ensure the appropriate height setting. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 9.
13 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM SEAT (FIGURE 10) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 10. 2. Position the rear J brackets securely into the fixed release clamps as shown in FIGURE 10.
14 ADJUSTING THE CONTOUR U SEAT HEIGHT (FIGURE 11) NOTE: There are six (6) height adjustments avail- able on the ContourU seat with a seat pan. NOTE: There are twelve (12) height adjustments available on the ContourU seat with a wood back.
15 ADJUSTING THE CONTOUR U SEATING SYSTEM SEAT ANGLE (FIGURE 12) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same height. Refer to ADJUSTING THE CONTOUR U SEAT HEIGHT in this instruction sheet. NOTE: The seat angle is adjusted by repositioning the front and/or the rear J brackets.
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare is a registered trademark of Elyria, Ohio USA Mississauga Ontario Invacare Corporation. 44036-2125 L4Z4G4 Canada Yes, you can. is a trademark of Invacare 800-333-6900 800-668-5324 Corporation.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Invacare OCMK78 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Invacare OCMK78 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Invacare OCMK78, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Invacare OCMK78 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Invacare OCMK78, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Invacare OCMK78.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Invacare OCMK78. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Invacare OCMK78 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
