Manuel d'utilisation / d'entretien du produit GENE-8310 du fabricant Intel
Aller à la page of 57
SubCompact Board GENE-8310 GENE-8310 I n t e l ® Celeron ® M Processor Subcompact Board With LVDS, Ethernet, 6 Channel Audio & Mini PCI GENE-8310 Rev .
SubCompact Board GENE-8310 i Copyright Notice This document is copyrighted, 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
SubCompact Board GENE-8310 i i Acknowledgments All other products’ name or tradem arks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association.
SubCompact Board GENE-8310 iii Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 GENE-8310 CPU Card • 1 IDE Cable • 1 KB/Mo.
SubCompact Board GENE-8310 i v Contents Chapter 1 General Information 1.1 Introduct ion ................................................................ 1-2 1.2 Featur es .................................................................... 1-4 1.3 Specific ations .
SubCompact Board GENE-8310 v 2.18 4P Power Conne ctor (CN9) .................................... 2-16 2.19 TV-out Connec tor (CN10) ....................................... 2-17 2.20 DVI Connecto r (CN11) ............................................ 2-17 2.
SubCompact Board GENE-8310 v i Appendix B I/O Information B.1 I/O Addre ss Map .................................................... B-2 B.2 1 st MB Memory Address Map ................................B-2 B.3 IRQ Mappi ng Chart .........................
SubCompact Board GENE-8310 C h a p t e r 1 G e n e r a l I n f o r m a t i o n 1- 1 General Chapter 1 Information.
SubCompact Board GENE-8310 Chapter 1 General Information 1-2 1.1 Introduction The GENE-8310 is the third generati on of fanless solutions that AAEON has released through their original design. It is more advanced than previous SubCompact Boards, with higher performance and lower power consumption.
SubCompact Board GENE-8310 Chapter 1 General Information 1-3 Intel ® platform. It has the best graphics cap ability among current 3.5” SubCompact Boards. In addition, the GENE-8310 supports CRT , LCD, DVI and TV -out which can meet your requirements.
SubCompact Board GENE-8310 Chapter 1 General Information 1-4 1.2 Features • Onboard Intel ® Celeron ® M or Mobile Intel ® Celeron ® Processor at 600MHz 0K L2 Cache Processor • 48-bit Dual Channels LVDS TFT LCD • 10/100Mbps Fast Ethernet • AC-97 3D Surround 5.
SubCompact Board GENE-8310 Chapter 1 General Information 1-5 1.3 Specifications System • CPU: Onboard Mobile Intel ® Celeron ® Processor at 600MHz with 0K L2 Cache or Intel ® Celeron ® M Processor 1.
SubCompact Board GENE-8310 Chapter 1 General Information 1-6 101.6mm) Gross Weight: 0.88lb (0.4kg) Operating Temperature: 32 ° F~140 ° F (0 ° C~60 ° C) Display Chip: Intel ® 852GM + C.
SubCompact Board GENE-8310 Chapter 1 General Information 1-7 USB: Two 5 x 2 Pin Headers Support 4 USB 2.0 Ports (Does not support Wake-up function).
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-1 Quick Inst allation Chapter 2 Guide Notice: The Quick Installatio n Guide is derive d f rom Chapter 2 of user manual. For othe r chapters and further ins tallation instructio ns, please refer to the use r manual CD-ROM that came with th e p roduct.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-2 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-3 2.2 Location of Connectors and Jumpers Component Side 1 5 5 1 1 6 9 1 0 1 2 1 1 2 1 8 7 MPCI1 CN15 CN13 CN10 .
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-4 Solder Side CFD1 DIMM1.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-5 2.3 Mechanical Draw ing Component Side 1 5 5 1 1 6 9 1 0 1 2 1 1 2 1 8 7 0.00 0 . 0 0 8.89 1 . 3 2 8.89 3 . 2 3 0.27 6.99 5 . 0 3 5 . 4 7 1 6 . 9 0 2 8 . 3 3 3 9 .
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-6 Solder Side 0.00 0 . 0 0 3 . 2 3 8.89 0.00 9 5 . 2 0 9 8 . 3 7 8.89 72.39 114.30 133.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-7 2.4 List of Jumpers The board has a number of jumpers t hat allow you to configure your system to suit your application.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-8 2.5 List of Connectors The board has a number of connectors t hat allow you to configure your system to suit your application. T he table below shows the function of each board's connectors: Connectors Label Function CN1 USB 2.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-9 CN17 Mini-DIN PS/2 Connector CN18 Serial Port COM 1 Connector CN19 CRT Display Connector VBA T2 External Batt.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-10 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-11 2.7 Clear CMOS Selection (JP1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.8 LCD Voltage Selection (JP2) JP2 Function 1-2 +5V (Default) 2-3 +3.3V 2.9 COM2 RI/+5V Selection (JP5) JP5 Function 1-2 +5V 3-4 RI (Default) 2.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-12 2.11 USB2.0 Port 2 Connector (CN2) Pin Signal P i n Signal 1 USBVDD2-3 2 USBGND 3 USBD2- 4 USBGND 5 USBD2+ 6 USBD3+ 7 USBGND 8 USBD3- 9 USBGND 10 USBVDD2-3 2.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-13 29 PDDACK# 30 Ground 31 IRQ14 32 N/C 33 PDA1 34 P66DET 35 PDA0 36 PDA2 37 PDCS#1 38 PDCS#3 39 IDEACTP# 40 Ground 41 +5V olt.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-14 Port 7 CN4. pin 7 Bit 1 U35. pin 26 (GPIO21) Port 8 CN4. pin 8 Bit 0 U35. pin 27 (GPIO20) 2.14 Front Panel (CN5) Pin Signal 1-2 A TX Powe r -on Button 3-4 HDD Active LED 5-6 External S peaker 7-8 Power LED 9-10 System Reset Button 2.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-15 9 Ground 10 N/C COM2/ RS-485 Mode Pin Signal P i n Signal 1 TXD- 2 N/C 3 TXD+ 4 N/C 5 N/C 6 N/C 7 N/C 8 N/C 9 Ground 10 N/C Note: COM mode, RS-232/422/485, selected by BIOS.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-16 2.17 Dual Channel LVDS Connector (CN8) Pin Signal Pin Signal 1 Back-Li g ht Enable 2 Back-Li g ht Control 3 LCD V olt.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-17 2.19 TV-Out Connector (CN10) Pin Signal Pin Signal 1 Y 2 CVBS 3 Ground 4 Ground 5 C 6 N/C 7 Ground 8 N/C 2.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-18 9 Audio Ground 10 CD_R 1 1 LINE_OUT L 12 LINE_OUT R 13 Audio Ground 14 Audio Ground 2.22 Ethernet 10/100Base-TX RJ- 45 Phone Jack Connector (CN13) Pin Signal Pin Signal 1 TX+ 2 T X - 3 TCT 4 N/C 5 N/C 6 RCT 7 RX+ 8 RX- 9 LINK_LED 10 ACT_LED 1 1 SPD_LED 12 +3.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-19 3 Rx 4 Ground 5 Tx 6 N/C (CIR_Rx Option) 2.25 Fan Connector (CN16) Pin Signal 1 F AN Sense 2 +5V 3 Ground 2.
SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-20 2.28 CRT Display Connector (CN19) Pin Signal Pin Signal 1 CRT RED 9 5V 2 CRT_GREEN 10 VGA Ground 3 CRT_BLUE 1 1 N/C 4 N/C 12 CRT_SDA 5 VGA Ground 13 CRT_HSYNC 6 VGA Ground 14 CRT_VSYNC 7 VGA Ground 15 CRT_SCL 8 VGA Ground 2.
SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-21 7 SDCS#1 32 SDCS#3 8 Ground 33 Ground 9 Ground 34 SDIOR# 10 Ground 35 SDIOW# 1 1 Ground 36 +5 V olt.
SubCompact Board GENE-8310 C h a p t e r 3 A w a r d B I O S S e t u p 3-1 Chapter Aw a r d 3 BIOS Setup.
SubCompact Board GENE-8310 Chapter 3 A ward BIOS Setup 3-2 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error duri ng the tests, you will either hear a few short beeps or see an error message on the screen.
SubCompact Board GENE-8310 C h a p t e r 3 A w a r d B I O S S e t u p 3 - 3 3.2 Aw ard BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery -backed CMOS RAM so that it retains the Setup information when the power is turned off.
SubCompact Board GENE-8310 Chapter 3 A ward BIOS Setup 3-4 Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify y our settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.
SubCompact Board GENE-8310 C h a p t e r 3 A w a r d B I O S S e t u p 3 - 5 While AWARD has desig nated the cu st om BI OS t o maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords.
SubCompact Board GENE-8310 C h a p t e r 4 D r i v e r I n s t a l l a t i o n 4-1 Chapter Driver 4 Inst allation.
SubCompact Board GENE-8310 Chapter 4 Driver Installation 4-2 The GENE-8310 comes with a CD-ROM that contains all drivers and utilities that meet your needs.
SubCompact Board GENE-8310 C h a p t e r 4 D r i v e r s I n s t a l l a t i o n 4-3 4.1 Installation: Insert the GENE-8310 CD-ROM in to the CD-ROM Driv e. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install Intel ® INF Update for Windows 2000/XP 1.
SubCompact Board GENE-8310 Chapter 4 Driver Installation 4-4 Step 4 – Install Realtek AC97 codec Driver 1. Click on the Realtek AC97 codec Driver folder and then double click on the setup.
SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-1 Programming the Appendix A W atchdog T imer.
SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-2 A.1 Programming GENE-8310 utilizes ITE 8712 chipset a s its watchdog timer controller.
SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-3 occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state.
SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-4 WatchDog Timer Configuration Registe rs Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-5 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Registe r (Index=72h, Default=00h) Watch.
SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-6 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7.
SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-7 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configura.
SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-8 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MO.
SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-9 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR.
SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-10 Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device e.
SubCompact Board GENE-8310 A p p e n d i x B I / O I n f o r m a t i o n B-1 I/O Information Appendix B.
SubCompact Board GENE-8310 Appendix B I/O Information B-2 B.1 I/O Address Map Address Description User Address 000-01F DMA Controller #1 000-000F 020-03F Interrupt Controller #1, Master 020-021 040-05.
SubCompact Board GENE-8310 A p p e n d i x B I / O I n f o r m a i o n B-3 B.3 IRQ Mapping Chart IRQ0 System Timer IRQ8 System CMOS / Real time clock IRQ1 Keyboard IRQ9 Microsoft ACPI – Compliant sy.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Intel GENE-8310 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Intel GENE-8310 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Intel GENE-8310, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Intel GENE-8310 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Intel GENE-8310, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Intel GENE-8310.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Intel GENE-8310. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Intel GENE-8310 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
