Manuel d'utilisation / d'entretien du produit DS-2000 du fabricant IBM
Aller à la page of 27
WARRANTY INFORMATION Qua Tech Inc. warrants the DS-200 0 to b e free of defects for one (1 ) year from the date o f purchase. Qua Tech Inc. will repair or replace any board that fails to perform under normal operating condition s and in accordance with the procedures outlined in thi s document during the warranty period.
TABLE OF CONTENTS WARRANTY INFORMATION . . . . . . . . . . . . i LIST OF FIGURES . . . . . . . . . . . . . ii i I. INTRODUCTION . . . . . . . . . . . . . . . . 1 II. BOARD DESCRIPTION . . . . . . . . . . . . . 1 III. 16550 FUNCTIONAL DESCRIPTION . . .
LIST OF FIGURES Figure 1. DS-2000 board layout . . . . . . . . . 2 Figure 2. 16550 internal registers . . . . . . . 3 Figure 3. Interrupt enable register . . . . . . 4 Figure 4. Interrupt identification register . . 5 Figure 5. Interrupt source identification .
I. INTRODUCTION The DS-2000 is a dual channel asynchronous seria l communication adapter which utilizes balanced differential drivers and receivers to provide RS-422-A communications. It is capable of reliable communication s over long distances (4000 feet) within noisy industria l environment.
FUNCTIONAL DESCRIPTION Figure 1. DS-2000 board layout . ii i.
FUNCTIONAL DESCRIPTION III. 1655 0 FUNCTIONAL DESCRIPTION The 16550 is an upgrade of the standard 1645 0 Asynchronous Communications Element (ACE). Designed t o be compatible with the 16450, the 16550 enters th e character mode on reset and in this mode will appear as a 16450 to user software.
FUNCTIONAL DESCRIPTION A. INTERRUPT ENABLE REGISTER +------- + D7 | 0 | +------- + D6 | 0 | +------- + D5 | 0 | +------- + D4 | 0 | +------- + D3 | EDSSI |----- MODEM statu s +------- + D2 | ELSI |---.
FUNCTIONAL DESCRIPTION B. INTERRUPT IDENTIFICATION REGISTER +------ + D7 | FFE |----- FIFO enable (FIFO only ) +------ + D6 | 0 | +------ + D5 | 0 | +------ + D4 | 0 | +------ + D3 | IID2 |-- + +------+ | D2 | IID1 | +-- Interrupt identification +------+ | D1 | IID0 |-- + +------ + D0 | IP |----- Interrupt pending +------ + Figure 4.
FUNC TIONAL DESCRIPTION +-------------------+----------+---------------------- + | IID2 IID1 IID0 IP | Priority | Interrupt Type | +-------------------+----------+---------------------- + | x x x 1 | .
FUNCTIONAL DESCRIPTION C. FIFO CONTROL REGISTER +------ + D7 | RXT1 |-- + +------+ +-- Receiver trigger D6 | RXT0 |-- + +------ + D5 | x |-- + +------+ +-- Reserved D4 | x |-- + +------ + D3 | DMAM |-.
FUNCTIONAL DESCRIPTION RRST - Receive FIFO Reset : When set (logic 1), all bytes in the receiver FIFO are cleared and the counter is reset. Th e shift register is not cleared. RRST is self - clearing . FE - FIFO Enable : When set (logic 1), enables transmitter and receiver FIFOs.
FUNCTIONAL DESCRIPTION STKP - Stick Parity : Forces parity to logic 1 or logic 0 if parity i s enabled. See EPS, PEN, and figure 9 . EPS - Even Parity Select : Selects even or odd parity if parity is enabled . See STKP, PEN, and figure 9 . PEN - Parity Enable : Enables parity on transmission and verification on reception.
FUNCTIONAL DESCRIPTION E. MODEM CONTROL REGISTER +------ + D7 | 0 | +------ + D6 | 0 | +------ + D5 | 0 | +------ + D4 | LOOP |----- Loopback enable +------ + D3 | OUT2 |----- Output 2 +------ + D2 | OUT1 |----- Output 1 +------ + D1 | RTS |----- Request to send +------ + D0 | DTR |----- Data terminal ready +------ + Figure 11.
FUNCTIONAL DESCRIPTION F. LINE STATUS REGISTER +------ + D7 | FFRX |----- Error in FIFO RCVR (FIFO only ) +------ + D6 | TEMT |----- Transmitter empty +------ + D5 | THRE |----- Transmitter holding re.
FUNCTIONAL DESCRIPTION Bits BI, FE, PE, and OE are the sources of receiver line status interrupts. The bits are reset by reading the line status register. In FIFO mode, these bit s are associated with a specific character in the FIFO and the exception is revealed only when that character reaches the top of the FIFO .
FUNCTIONAL DESCRIPTION G. MODEM STATUS REGISTER +------ + D7 | DCD |----- Data carrier detect +------ + D6 | RI |----- Ring indicator +------ + D5 | DSR |----- Data set ready +------ + D4 | CTS |-----.
FUNCTIONAL DESCRIPTION H. SCRATCHPAD REGISTER This register is not used by the 16550. It may b e used by the programmer for data storage . IV. FIFO INTERRUPT MODE OPERATION 1. The receive data interrupt is issued when the FIFO reaches the trigger level.
B AUD RATE SELECTION J1 J 1 +-----------+ +----------- + 1| o o+ o |4 1| o--o o | 4 2| o o+ o |5 2| o o--o | 5 +-----------+ +----------- + (a) ÷1 input clock (b) ÷2 input clock J1 J 1 +-----------+.
ADDRESSING VI. ADDRESSING Each channel of the DS-2000 uses 8 consecutive I/O address locations. The base addresses are independen t but must begin on an even 8-byte boundary (xxx0H - xxx7H or xxx8H - xxxFH).
PROGRAMM ABLE OPTION SELECT The remaining POS registers are used for address and interrupt selections. These registers are programmed by the user through the IBM installation utility supplied with the PS/2. These registers are read/write but should not be written to by user software.
PROGRAMMABLE OPTION SELECT +-------------------------+------------------- + | ADSx3 ADSx2 ADSx1 ADSx0 | Base address | +-------------------------+------------------- + | 0 0 0 0 | 3F8H (Serial 1) | | .
OUT PUT CONFIGURATIONS IX. OUTPUT CONFIGURATIONS Two sets of jumpers are implemented on the DS-200 0 to control the auxiliary driver/receiver set. Jumpers J 2 and J3 perform identical functions on channels 1 and 2 respectively . The function of J2 and J3 is to control the source of the data exchanged on the auxiliary communication lines.
OUTPUT CONFIGURATIONS The other function of J2 and J3 is to configure th e communication channel in half or full duplex mode. Hal f duplex operation is achieved by connecting pins 4 and 8 of the jumper block (figure 23).
OUTPUT CONFIGURATIONS +----------- + | RI +-+ +------ + | DCD +-+ +-+ inv. +- + | DSR +-+ | +------+ | (4,5,6 for channel 1 , | DTR +-+----+----o o o 1,2,3 for channel 2 ) | | J4 | +---------- + | RCL.
OUTPUT CONFIGURATIONS AUXIN ------+ +------ RCLK CTS --+ | | +-- DTR +------------------- + 5 | o---o o+ o | 8 1 | o---o o+ o | 4 +------------------- + RTS --+ | | +-- driver enable AUXOUT ------+ +------ XCLK J2 _ Channel 1 J3 _ Channel 2 Figure 21.
EX TERNAL CONNECTIONS X. EXTERNAL CONNECTIONS Connections to peripheral equipment are made via a female D-9 connector. A pin-out of the D-9 connector and a detailed description of each output signal i s illustrated in figures 24 and 25 . Figure 24. D-9 output configuration .
INSTALLATION XI. INSTALLATION Make sure there is a copy of th e original reference diskette available . This diskette must be modified t o accept any option adapters . 1. Turn unit off . 2. Remove system cover as instructed in the IBM Quick Reference Guide .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté IBM DS-2000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du IBM DS-2000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation IBM DS-2000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le IBM DS-2000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le IBM DS-2000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du IBM DS-2000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le IBM DS-2000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei IBM DS-2000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
