Manuel d'utilisation / d'entretien du produit 09-0572-000 du fabricant IBM
Aller à la page of 101
® T OKEN L INK III 1 6/4 ISA A DAPTER U SER G UIDE A member of the TokenLink III product family Part No. 09-0572-000 Published October 1995.
® L IFETIME W ARRANTY 3Com ’ s EtherLink , T okenLink III 16/4, F ast EtherLink, FDDILink , and 3Com Impact ISDN ISA adapters have a Lif etime W arranty . T o ensure the ver y best 3Com service and suppor t, take the time to complete the product registration card .
Customers in the countries shown belo w should send the completed registration card to the appr opriate address. Customers in other non-U.S. locations should send the registration card to the U.S. addr ess on the front of the card . ■ Asia 3Com Asia Ltd.
3Com C orporation ■ 5400 Bayfront Plaza ■ Santa Clara, California ■ 95052-8154 © 3Com Corporation, 1995. All rights reserved. No par t of this documentation may be reproduced in any form or by an y means or used to make any derivative work (such as translation, transformation, or adaptation) without permission from 3Com Corporation.
C ONTENTS A BOUT T HIS G UIDE Introduction i How to Use This Guide i Con ventions ii 1 I NTRODUCTION T okenLink III 16/4 ISA T oken Ring Adapter F eatures 1-1 Installation and Configuration Options 1.
4 S TANDARD I NSTALLATION AND C ONFIGURATION Configuration Requirements 4-2 Auto C onfiguring the 3C619C Adapter in an ISA PC 4-2 Changing Sof tware Option Settings 4-5 Changing Settings for Multipl.
7 T ROUBLESHOOTING Adapter LEDs 7-1 Using the T okenDisk Disk ette Diagnostic Program 7-2 Diagnostic T est T ypes 7-4 Group 1 Diagnostics 7-4 MMIO Register Write/Read T est 7-4 Boot PROM T est 7-4 AIP.
A U SING THE C ONFIGURATION AND D IAGNOSTIC P ROGRAM Using the Keyboard A-2 Speed Keys A-2 Using the Mouse A-3 Choosing a Menu Item A-3 Using the File Options A-4 Help A-4 Exiting the Program A-5 Usin.
G LOSSARY I NDEX L IMITED W ARRANTY FCC C LASS A V ERIFICATION S TATEMENT CE N OTICE.
F IGURES 1-1 Adapter Installation and Configuration 1-3 2-1 3C619C Adapter Installation 2-2 2-2 Removing the Cov er 2-5 2-3 Removing the Backplate 2-6 2-4 Installing the Adapter 2-7 2-5 Attaching the.
T ABLES 1 T ext Con ventions ii 2 Notice Icons ii 4-1 3Com Mode versus IBM Mode 4-4 4-2 Initial 3Com and IBM Mode Option Settings 4-5 A-1 Definition of Keys A-2 A-2 Definition of Menu Items A-3 A-3 .
A BOUT T HIS G UIDE Introduction This guide describes how to install, configure , and troubleshoot the T ok enLink III 16/4 ISA (3C619C) adapt er . If the information in the README.T X T file shipped with y our product differs from the information in this guide , follow the instructions in the README.
ii A BOUT T HIS G UIDE C onv entions T able 1 and T able 2 list text and icon conventions that ar e used throughout this guide: T able 1 T ex t C onventions Convention Description Text represented as .
1 I NTRODUCTION The 3Com T okenLink III 16/4 ISA T oken R ing Adapter (3C619C) is a 16-bit network adapter . T he 3C619C adapter can be installed in any IBM -compatible UL -listed PC with an Industr y Standar d Architecture (ISA) bus or Extended Industr y Standar d Architecture (EISA) bus.
1-2 C HAPTER 1: I NTRODUCTION The 3C619C adapter can be configured in one of tw o modes: 3Com mode or IBM mode. 3C om mode increases the number of available IRQ channels fr om 4 to 8 and the number of I/O base addresses from 2 to 32. Y ou can install up to six adapters per PC.
Installation and Configuration Options 1-3 Figure 1-1 Adapter Installation and C onfiguration Inspect adapter Connect adapter cable to UTP network Install adapter Connect adapter cable If memory mana.
1-4 C HAPTER 1: I NTRODUCTION Standard Installation and C onfiguration The standard installation and configuration procedur es can be used to configure the 3C619C adapter , test the adapter , and install drivers.
100% Compatibility 1-5 Money-Back Guar antee If a 3Com T ok enLink III 16/4 adapter is not 100% compatible (as defined above) with an y driver or application written to function on an IBM adapter , 3Com will refund the purchase price of the adapter .
2 I NSTALLING THE 3C619C A DAPTER This chapter describes how t o install a 3Com 3C619C token ring adapter in an ISA or EISA PC and connect it to the network.
2-2 C HAPTER 2: I NSTALLING THE 3C619C A DAPTER Figure 2-1 3C619C Adapter Installation Inspect adapter Connect STP cable to network Install adapter Connect cable to installed adapter Network cabling t.
PC Requirements 2-3 PC Requirements Installation of the 3C619C adapter requires the f ollowing: ■ An ISA- or EISA-bus PC with at least 640 K of RAM and an 80386 processor . ■ An available 16-bit (ISA) or 32-bit (EISA) expansion slot. ■ A high-density 3.
2-4 C HAPTER 2: I NSTALLING THE 3C619C A DAPTER T aking Safety Precautions W ARNING: The adapter board is installed in a PC that operates with v oltages that can be lethal. Before you remov e the cov er of your PC, you must obser ve the follo wing steps to protect yourself and pr event damage to the PC’ s components .
Installing the Adapter 2-5 4 Check the adapter for an y visible signs of damage. If you find a problem, immediately notify your authorized network supplier and the carrier that delivered the adapt er . After you hav e unpacked the adapter , complete the Pr oduct Registration C ard at the back of this manual and return it to 3Com.
2-6 C HAPTER 2: I NSTALLING THE 3C619C A DAPTER Figure 2-3 Removing the Backplate 2 Remove the scr ew holding the expansion slot ’ s backplate , as shown in F igure 2-3. Y our PC may look different from the one illustr ated, particularly if it is an EISA PC.
Connecting to the Network 2-7 Figure 2-4 Installing the Adapter C onnec ting to the Network Connect one of the following types of network cables to the 3C619C adapter . T ok enLink III adapters support industr y-standar d token ring type 3 (UTP) or types 1 or 6 (STP) cabling.
2-8 C HAPTER 2: I NSTALLING THE 3C619C A DAPTER C onnec ting to S hielded T wisted-pair (STP) Cable 1 Locat e the adapter ’ s DB-9 connector on the backplate, as shown in F igure 2-5. Figure 2-5 Attaching the STP Cable with the DB-9 C onnec tor 2 Locat e the DB-9 connec t or on the shielded twisted-pair cable.
Connecting to the Network 2-9 C onnec ting to Unshielded T wisted-pair (UTP) Cable 1 Locat e the adapter ’ s RJ-45 por t on the backplate , as shown in F igure 2-6. Figure 2-6 Attaching the UTP Cable with the RJ-45 C onnec tor 2 Align the RJ-45 plug on the end of the unshielded twisted-pair cable with the notch on the adapter’ s por t.
3 U SING THE A UTO L INK F EATURE FOR N ET W ARE The AutoLink aut o installation feature for NetW are configures the adapter as a NetW are DOS ODI client.
3-2 C HAPTER 3: U SING THE A UTO L INK F EATURE FOR N ET W ARE ■ Logs in to the server and updates the NetW are client software if a 3Install account exists on the ser v er ; otherwise, the client software is installed from the T okenDisk diskette. ■ Modifies the CONFIG.
Avoiding Memory Manager Conflicts 3-3 A voiding Memory Manager Conflicts If you are using a memory manager on your PC (all PCs running Microsoft Windows ha ve a memor y manager such as EMM386 or its equivalent), you need to inf orm the memor y manager of the memor y used by the 3C619C adapter .
3-4 C HAPTER 3: U SING THE A UTO L INK F EATURE FOR N ET W ARE Using the A utoLink F eature F ollow these steps to use the AutoLink f eature: 1 Place the T ok enDisk diskette in a floppy drive on your PC and make that drive the active driv e.
4 S TANDARD I NSTALLATION AND C ONFIGURATION This chapter describes how t o configure the 3C619C adapter in a DOS or OS/2 PC, using the steps shown in Figur e 4-1.
4-2 C HAPTER 4: S TANDARD I NSTALLATION AND C ONFIGURATION The ISA adapter can be configured aut omatically or manually . Automatic configuration selects configuration values for the adapter . Manual configuration allows you to select the resources yourself .
Auto Configuring the 3C619C Adapter in an ISA PC 4-3 3 Place the T ok enDisk diskette in a floppy drive on your PC and make that drive the active driv e. For example , type: A: [Enter] 4 T ype at the prompt: INSTALL [Enter] 5 The first time you use the diskett e to install the adapter software, a software license screen appears.
4-4 C HAPTER 4: S TANDARD I NSTALLATION AND C ONFIGURATION 8 When prompted , select the operating mode and speed . The 3C619C adapter off ers the following choices: ■ 3Com mode , 16 Mbps ■ 3Com mo.
Changing Software Option Settings 4-5 If you are running Windows NT or Windows 95 and installing a single adapter , the adapter’ s default configuration can be used. Install the driv er as described in Chapter 6. I f the configuration is not suitable, you can change the settings by following the pr ocedure in this chapter .
4-6 C HAPTER 4: S TANDARD I NSTALLATION AND C ONFIGURATION T o change the sof twar e option settings, follow these steps: 1 Make sure the 3C619C adapter has been properly installed in your PC (ref er to Chapter 2 for instructions). 2 Boot your PC under DOS, version 3.
Changing Software Option Settings 4-7 7 When the next screen appears, select Configuration and Diagnostic Progr am. 8 Highlight Install and press [Enter]. 9 Press [Ent er] to selec t C onfigure Adapter . A screen similar to the one shown in F igure 4-3 appears.
4-8 C HAPTER 4: S TANDARD I NSTALLATION AND C ONFIGURATION If you want to use the same settings on other adapters , you can sav e the configuration settings to a file. Select <Save> under the <F ile O ptions> c ommand button in the Adapter Configur ation dialog box.
Changing Software Option Settings 4-9 This completes the installation and configuration process . The next step is to install the network drivers. See Chapt er 5, “Installing Network Drivers , ” or Chapt er 6, “Installing the Network Driver f or Windows .
5 I NSTALLING N ETWORK D RIVERS This chapter describes how to install the network driv ers. F igure 5-1 depic ts the menu-driven netw ork driver installation steps.
5-2 C HAPTER 5: I NSTALLING N ETWORK D RIVERS The follo wing net work drivers are on the T okenDisk diskette: ■ Novell NetW are DOS ODI driver (3CT OKEN.COM) ■ NetW are OS/2 ODI (3CTOKEN.SY S) ■ NetW are ser v er driver (3CTOKEN.LAN) ■ NDIS 2.
Installing the Novell NetWare Driver 5-3 2 When the next screen appears, select Install Novell NetW are Drivers , as shown in Figur e 5-3, and press [Enter].
5-4 C HAPTER 5: I NSTALLING N ETWORK D RIVERS 4 At the prompt , enter a path for the destination of the driver , or accept the default. 5 Exit to DOS and follow the instructions in the next section to make the necessary changes to your A UTOEXEC.BA T and C ONFIG.
Installing the Novell NetWare Driver 5-5 Installing the OS/2 Network Driv er for NetW are The T okenDisk diskette includes the Novell NetW are OS/2 ODI driver (NET W AREODI3CTOKEN.SY S). Instruc tions f or installing this driver are pro vided in the NET W AREODIOS2REQ.
5-6 C HAPTER 5: I NSTALLING N ETWORK D RIVERS Installing the NDIS 2.01 Driver The Network Driver Int er face Specification (NDIS) was developed by Microsoft and 3Com. This software specification is used in network operating systems such as IBM LAN Server or M icrosoft LAN Manager to create drivers f or network adapters.
Installing the NDIS 2.01 Driver 5-7 Updating the PC Startup Files This sample procedure describes ho w to modify the PRO TOC OL.INI and CONFIG.SYS PC startup files to load the NDIS drivers for a PC running LAN Manager . 1 Create a LANMAN subdir ec tory from the root of y our boot disk using the following c ommand: MD LANMAN 2 Build a PRO TOC OL.
5-8 C HAPTER 5: I NSTALLING N ETWORK D RIVERS NDIS Sy stems with Multiple Adapters If you are installing more than one 3C619C adapter , the PRO TOC OL.INI file must be modified to bind the driver to each adapter . P arameters must be added to the file to distinguish each adapter attached to the same driver .
Updating the Current NDIS Driver 5-9 Updating the C urrent NDIS Driv er If you are updating an existing NDIS driver (rather than installing one for the first time), follow these st eps: 1 Fr om the main menu, selec t Network Drivers and press [Enter].
5-10 C HAPTER 5: I NSTALLING N ETWORK D RIVERS T o use the IBM 16/4 T oken Ring Adapter drivers supplied with your network operating system, copy them to y our PC and follow an y provided instructions.
Using IBM Drivers 5-11 Enabling RPL The follo wing instruc tions explain how t o use the RPL program when your PC has both a hard disk driv e and a floppy disk drive. Ref er to your network operating system documentation for the steps to be performed on the network to use RPL and f or information on different drivers that you can load with RPL.
5-12 C HAPTER 5: I NSTALLING N ETWORK D RIVERS Disabling RPL T o disable RPL: 1 Boot your PC under DOS. 2 Make sure that the backup cop y of the T okenDisk diskette is in a floppy drive on y our PC. 3 At the diskette pr ompt, type: 3TOKDIAG [Enter] 4 Fr om the Install pull-down menu, selec t C onfigure Adapter .
6 I NSTALLING THE N ETWORK D RIVER FOR W INDOWS This chapter describes how t o install the net work driver for Windows NT and Windows 95. The 3Com NDIS 3.0 netw ork driver suppor ts Microsoft Windows NT Version 3.51 and Microsoft Windows 95. Installing the Network Driv er for Windows NT The T okenDisk diskette includes the NDIS 3.
6-2 C HAPTER 6: I NSTALLING THE N ETWORK D RIVER FOR W INDOWS 7 At the prompt , type A:WINNT351ISA if you installed the adapter in an ISA slot. Type A:WINNT351EISA if you installed the adapter in an EISA slot using the EISA configuration utility (that is , auto-sense is enabled and the I/O base address = EISA).
Installing the Network Driver for Windows 95 6-3 5 Fr om the S elect Network Component T ype dialog box, double-click Adapter . 6 Fr om the S elect Network Adapters dialog bo x, click Hav e Disk. 7 Insert the T okenDisk diskette in the floppy driv e.
7 T ROUBLESHOOTING This chapter describes inf ormation for isolating and solving problems. It contains the following sections: ■ Adapter LEDs ■ Using the T okenDisk Disk ett e Diagnostic Program .
7-2 C HAPTER 7: T ROUBLESHOOTING Figure 7-1 Adapter LEDs When lit, the green LED (labeled “4”) indicates that the adapter is set to 4 Mbps speed and is correctly inser ted int o the ring. When lit, the yellow LED (labeled “16”) indicates that the adapter is set to 16 Mbps and is correctly inser ted into the ring .
Using the TokenDisk Diskette Diagnostic Program 7-3 If you have alr eady installed the net work driv er , you need to reboot and press [F5] or use a DOS diskette to b ypass the drivers before y ou run the diagnostic program. Use a DOS diskette if you ar e running DOS 5.
7-4 C HAPTER 7: T ROUBLESHOOTING Diagnostic T est T ypes The tests performed by the T okenDisk diskette C onfiguration and Diagnostic Pr ogram are divided into Group 1 and Group 2 tests. A lobe cable must be c onnected from the selected adapter to a retiming conc entrator or MAU for all tests .
Diagnostic Test Types 7-5 AIP Checksum T est This test verifies that the adapt er ’ s node ID , channel identifier , and suppor ted function identifiers such as data rate, shared RAM, and transmit buffer size are corr ec t.
7-6 C HAPTER 7: T ROUBLESHOOTING Group 2 Diagnostic The Group 2 diagnostic (A dapter W rap T est) is a wrap test that causes all user-transmitted data to be sent and receiv ed without going to the network. A lobe cable must be c onnected from the selected adapter to a retiming conc entrator or MAU for all tests .
Diagnostic Test Types 7-7 If you want to run the tests continuously , selec t the Continuous option in the T est Setup dialog box, as described in the next section, “Changing the T est Setup.
7-8 C HAPTER 7: T ROUBLESHOOTING Changing the T est Setup If you want to change the test parameters , follow these steps: 1 Choose the <T est Setup> command button in the Run T ests dialog box shown in F igure 7-4. The T est Setup dialog box appears, as shown in F igure 7-5.
Adapter Statistics and Information 7-9 When T ests F ail If any test fails , you can get additional information b y highlighting the test that failed in the Run T ests dialog box shown in F igure 7-4, and pressing [Enter]. Y ou can also highlight the <Zoom> command button and pr ess [Enter].
7-10 C HAPTER 7: T ROUBLESHOOTING Adapter Inf ormation Use the V iew pull-down menu and select Adapter Information, or press [F8] from the main screen. An example of the A dapter Information screen is sho wn in Figure 7-7. Figure 7-7 Adapter Inf ormation Use the scroll bar to display the full list of paramet ers on this screen.
When Tests Fail 7-11 The follo wing information is displayed on the screen, indicating what to do when the specific test fails. MMIO Register W rite/Read T est F ailure ■ Check the ROM base address setting on the adapter and make sure that it is not being used by another device.
7-12 C HAPTER 7: T ROUBLESHOOTING Shared RAM W rite/Read T est F ailure ■ Make sure the shared RAM address does not conflict with the adapter ROM or another device. ■ Run the test three times with a delay of at least 30 seconds between each test.
Troubleshooting Tips 7-13 Close A dapter T est F ailure ■ Make sure a lobe cable is properly connected to the adapter and that the other end of the cable is connected to a DA U, MAU, or CA U. ■ Run the test three times with a delay of at least 30 seconds between each test.
7-14 C HAPTER 7: T ROUBLESHOOTING 4 Make sure that the settings (memory allocations, interrupts, and so on) for the adapter do not conflict with the PC or other adapter boards installed in the PC.
Additional Information 7-15 12 Replace the failed adapter with a known working adapter . If the second adapter fails, something is probably wrong with the test envir onment, not the adapter . Additional Inf ormation T roubleshooting help can be found in three other locations .
A U SING THE C ONFIGURATION AND D IAGNOSTIC P ROGRAM The T okenDisk diskette C onfiguration and Diagnostic Program is arranged in the hierarchy shown in F igure A-1. Figure A-1 Menu Hierarchy Y ou can use the k eyboard (function keys or speed keys) or a mouse to access the command buttons.
A-2 A PPENDIX A: U SING THE C ONFIGURATION AND D IAGNOSTIC P ROGRAM Using the K eyboard The follo wing table describes the k eys t o use with the T okenDisk disk ett e Configuration and Diagnostic Program. Speed Ke ys Pr ess [Alt] and the highlighted letter in any menu item or command button to activate that function.
Using the Mouse A-3 Using the Mouse If you have a mouse , you can use it to click on any of the menu items, command buttons , or listed items in a dialog box. Make sure that a mouse driver is loaded . Choosing a Menu Item Listed below are the menu it ems in the T okenDisk diskette Configuration and Diagnostic P rogram.
A-4 A PPENDIX A: U SING THE C ONFIGURATION AND D IAGNOSTIC P ROGRAM Using the F ile Options The F ile Options are located in dialog boxes on the Run T ests, T est S etup , and Configure A dapter screens. The options are: ■ Load: loads a file from a selected directory .
Exiting the Program A-5 T o print the help file, first exit the program. At the DOS prompt, enter the print command applicable to your PC software . For example, type: TYPE 3CTOKENG.HLP> PRN [Enter] Exiting the Pr ogram T o exit the program, press [Esc] until the DOS prompt appears .
B S PECIFICATIONS This appendix describes the specifications for the 3C619C adapter and contains the following sections: ■ Cabling ■ Pin Assignments ■ Configuration Options Cabling 3C619C adapters support industr y-standar d token ring cabling that follows IEEE 802.
B-2 A PPENDIX B: S PECIFICATIONS Figure B-1 DB-9 Connector Pin Assignments Figure B-2 RJ-45 Connector Pin Assignments 4 16 RX TX RX TX 1 2 3 4 5 6 7 8 9 4 16 1 2 3 4 5 6 7 8 TX (3) 12345678 RX (4) RX .
Configuration Options B-3 C onfiguration Options This section contains the configuration options for the 3C619C adapter . The follo wing options are available: ■ Configuration Mode ■ Ring Speed.
B-4 A PPENDIX B: S PECIFICATIONS Ring Speed The 3C619C adapter operates at either 4- or 16-Mbps ring speed. The adapter ring speed must match the speed of the token ring network. The default is 16 Mbps. I/O Base Addr ess In IBM mode when only one adapter is installed , it is designated the Primary adapter .
Configuration Options B-5 BIOS/MMIO Addr ess Location There are 16 possible 8 KB blocks of PC memory that can be assigned for accessing the ROM area of the 3C619C adapt er .
B-6 A PPENDIX B: S PECIFICATIONS If a conflict exists, you may have t o change the settings of other adapters or options that are in your PC. The 30 RAM address ranges are as f ollows, with the defau.
Configuration Options B-7 Other Configur ation Options The T okenDisk diskette Configuration and Diagnostic Pr ogram also allows the selection of the following additional parameters: Memory Mode – allows operation with 8-bit or 16-bit memor y inter faces.
C E RROR M ESSAGES This appendix contains an alphabetical list of the error messages that may appear when you use the T okenDisk diskette Configuration and Diagnostic P rogram for the 3C619C adapter .
C-2 A PPENDIX C: E RROR M ESSAGES An adapter was configured from EISA t o ISA mode, but the EISA configuration utility has not run yet. Place your EISA configuration diskette in drive A, and reboot the PC. An EISA configured adapter is installed in an ISA PC.
Messages C-3 The adapter’ s BIOS/MMIO base address is in conflict with another device installed in the system. T o run diagnostic tests, you must reconfigure the adapt er to another BIOS/MMIO base address. The BIOS/MMIO domain conflicts with the Shared RAM domain.
C-4 A PPENDIX C: E RROR M ESSAGES The value xxxx at line xxxx in the configuration file is not suppor ted . A list of supported option settings is provided in the INSTRUCT .TXT file in the DIAG subdirector y of this diskette. The value xxxx on the command line is not supported.
Messages C-5 Unable to locate an unused shared RAM base addr ess. Try the following: 1. Boot the PC with no drivers or TSR’ s loaded. 2. If a Memor y Manager is loaded, ex clude from it the memor y segment to be assigned to the 3C619C adapters . Unable to recognize v alue xxxx at line xxxx in the configuration file.
D T ECHNICAL S UPPORT 3Com pro vides easy access to technical suppor t inf ormation through the variety of services described in this appendix. On-line T echnical Ser vices 3Com off ers worldwide prod.
D-2 A PPENDIX D: T ECHNICAL S UPPORT W orld Wide W eb Site Access the latest netw ork ing inf ormation on 3Com ’ s World Wide Web sit e by entering our URL into your Internet browser: http://www.
Support from Your Network Supplier D-3 ■ NetF acts provides data sheets and technical ar ticles on 3Com C orporation’ s hub , bridge , router , terminal ser v er , and software products. Document 8888 provides you with an index of system product documents.
D-4 A PPENDIX D: T ECHNICAL S UPPORT If you are outside the U.S. and Canada, contact your local 3Com sales office to find y our authorized ser vice pro vider : Returning Pr oduc ts for Repair A product sent directly to 3Com for r epair must first be assigned a Return Materials Authorization (RMA) number .
G LOSSARY 3Com mode A mode of operation for the 3Com T ok enLink III adapter that provides expanded configuration options f or the adapter and drivers. CA U Controlled access unit. Configur ation The software settings that allow differ ent hardware components of a PC to communicate with one another .
2 G LOSSARY IEEE 802.5 The standard f or the token ring access method and Physical layer specifications dev eloped by a subcommittee of the Institute for Electrical and Electronics Engineers (IEEE) 802 committee.
G LOSSARY 3 NET .CFG An ASCII file containing control information f or network protocol elements of stations and servers for a Novell NetW are environment. Network A series of nodes such as PCs , terminals , or other peripherals interconnected by a communications channel.
4 G LOSSARY TSR T erminate and stay r esident. A program that upon execution, loads itself (or an executable portion of itself ) into PC working memor y (RAM).
I NDEX Numerics 3C619C adapter 1-1 configuring 3-1 , 4-1 , 4-2 default settings 4-5 information 7-10 , 7-15 inspecting 2-4 installing 2-1 , 2-5 PC requirements 2-3 statistics and information 7-9 3Com Bulletin Board Service (3ComBBS) D-1 3Com mode 1-2 , 4-4 , 5-8 , B-3 3Com sales offices D-4 3ComF acts D-2 3CT OKEN.
2 I NDEX configuration options AutoSwit ch 4-6 , B-7 BIOS/MMIO base address 4-5 Boot PROM 4-6 , B-7 configuration mode 4-5 , B-3 interrupt request level 4-5 , B-6 I/O base address 4-5 , B-4 I/O mode.
I NDEX 3 M main menu 5-3 MAU 2-8 , 7-4 , 7-6 memory conflic ts 3-3 , 4-2 , 4-6 memory manager 3-3 memory mode 4-6 , B-7 menu hierarchy A-1 menu items Install A-3 Configure A dapter A-3 Quit A-3 Abou.
4 I NDEX RPL disabling 5-12 enabling 5-11 Run T ests dialog box 7-6 , 7-7 Run T ests menu item 7-7 running diagnostic tests 7-6 S safety precautions 2-4 setup. See configuration. shared RAM page size and address range 3-3 , 4-5 , B-5 shielded twisted-pair cable (STP) 2-8 SMART AGT .
LIMITED W ARRANTY HARDW ARE: 3Com warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following lengths of time from the date of .
3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S M.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté IBM 09-0572-000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du IBM 09-0572-000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation IBM 09-0572-000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le IBM 09-0572-000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le IBM 09-0572-000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du IBM 09-0572-000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le IBM 09-0572-000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei IBM 09-0572-000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
