Manuel d'utilisation / d'entretien du produit YTH26V54 du fabricant Husqvarna
Aller à la page of 52
07002 YTH26V54 Owner's Manual 532 44 11-32 Rev 1 Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty .
2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AIL URE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 UNASSEMBLED P ARTS ...........................
5 UNAS SEMBLED P ARTS (5) Large Retainer Springs (1) Small Retainer Springs (5) 1-3/16 O .D. W ashers (2) Rear Lift Link Assemblies (1) F ront Lift Link Assembly (1) Anti- Sway Bar (1) 3/4 O .
6 AS SEMBL Y NOTE: Y ou may now roll your tractor off the skid. F ollow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al.
7 AS SEMBL Y TRANSAXLE 02965 FRONT BACK ENGINE Q. DEFLECTOR SHIELD Q Fig. 6 90° END INTEGRA TED WASHER END ANTI-SWA Y BAR (S) TOWARDS TOW ARDS TRANSAXLE MOWER DECK • F rom right side of mower , first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle.
8 AS SEMBL Y 6. A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 12) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor .
9 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled.
10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models onl.
11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING Y OUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
12 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs.
13 OPERA TION TO MOVE FORWARD AND BACK WARD (See Fig. 20) The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake. • Slowly depress forward (K) or reverse (L) drive pedal to begin movement.
14 Fig. 23 OPERA TION Fig. 24 TO TRANSPORT (See Figs. 16 and 24) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po- si tion. Free wheel control is located at the rear drawbar of tractor .
15 OPERA TION CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORT ANT : WHEN OPERA TING IN TEMPERA TURES BEL OW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP ENSURE GOOD COLD WEA THER ST ART ING.
16 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time.
17 MAINTENANCE T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil.
18 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
19 MAINTENANCE ENGINE LUBRICA TION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. NOTE: Although multi-viscosity oils (5W30, 10W30 etc.
20 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
21 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key .
22 SERVICE AND ADJUSTMENTS FRONT - TO-BACK ADJUSTMENT (See Figs. 36 & 37) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
23 SERVICE AND ADJUSTMENTS Fig. 38 TO REPL ACE MOTION DRIVE BEL T (See Fig. 38) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO REMOVE MOWER” section in this manual).
24 SERVICE AND ADJUSTMENTS TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 40) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries.
25 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood.
26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start.
28 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
29 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 SCHEMA TIC NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE.
30 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V.
31 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 41 41-25.
32 52 217 189 189 152 68 68 213 218 228 228 194 180 58 189 189 233 233 182 68 68 176 176 175 165 183 236 150 34 130 130 177 235 195 176 37 194 194 162 282 282 36 36 285 286 283 199 284 287 14 130 130 .
33 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 CHASSIS KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.
34 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 DRIVE 231 51 170 225 125 drive-tex_K46_pedal_39_r1 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 64 188 161 35 184 167.
35 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - - - - - T ransaxle, TUFFTORQ K46 2 532 12 35-83 K ey 15 819 13 13-16 W asher 13/32 x 13/16 x 16 Ga.
36 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 ENGINE 1 84 12 11 41 42 85 29 SP ARK ARRESTER KIT 84 45 18 15 37 28 37 21 20 engine-te x_bs-2cyl_47_r1 81 82 9 90 62 71 70.
37 KEY P ART NO . NO . DESCRIPTION 1 - - - - - - Engine Briggs & Stratton Model No. 44P777-1553-G1 2 532 14 97-23 Muffler 9 532 19 43-20 K eeper Belt Engine 11 532 40 00-08 Clutch 12 532 40 50-97 Pulley Engine 15 532 41 41-51 T ank F uel 18 532 43 92-08 Cap Asm F uel 20 532 42 35-02 Control Throttle/Choke 21 532 41 63-58 Screw #10 x .
38 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 STEERING ASSEMBL Y steering-tex_HUSQHR_4 6 5 13 13 53 8 9 8 7 9 8 7 62 4 70 68 69 67 67 66 15 15 14 14 61 2 6 35 59 58 16 .
39 KEY P ART NO . NO . DESCRIPTION 1 532 43 97-40 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm.
40 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 SEA T AS SEMBL Y 1 532 42 40-68 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock W/Ins.
41 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-te x_23 91 89 87 89 87 91 2 532 42 20-27 Shaft Asm.
42 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 MOWER DECK MOWER?DECKªTEX??R .
43 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 MOWER DECK KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE : All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 44 15-47 Deck Weldment Mower 6 532 19 60-66 Cover Mandrel LH 7 532 19 71-81 Cover Mandrel RH 8 532 19 30-03 Bolt 7/16 Asm.
44 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
45 &RQVXPHU:KHHOHG3URGXFWV ±/LPLWHG:DUUDQW +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV + XVTYDUQD SURGXFW LV IUHH IUR.
46 F 3UHYHQWDWLYHPDLQWHQDQ FHDVRXWOLQHGLQWKH RSHUDWRU¶VPDQXDO ,Q DGGLWLRQ RX PXVW FHDVH XVLQJ WKH SURGXFW LPPHGLDWHO XSRQ DQ IDLOXUH.
47 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLR.
48 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLR.
49 SERVICE NOTES.
50 SERVICE NOTES.
51 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e .
12.14.10 BAD Printed in the U.S.A..
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna YTH26V54 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna YTH26V54 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna YTH26V54, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna YTH26V54 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna YTH26V54, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna YTH26V54.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna YTH26V54. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna YTH26V54 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
