Manuel d'utilisation / d'entretien du produit O0803001 du fabricant Husqvarna
Aller à la page of 26
Operator's Manual 200 8 -0 1 O 0 8 0 300 1 EZ / MZ Collection System (Fab Deck) Operator's Manual 4 2"/ 48"/ 5 2"/ 61".
T ABLE OF CONTENTS SAFETY RULES ............................................................................................................................ 4 CART ON CONTENTS ...........................................................................
4 SAFETY RULES DANGER ! THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROWING OB- JECTS. F AILURE TO OBSER VE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESUL T IN SERI- OUS INJURY OR DEA TH. SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS I.
5 DO NOT • Do not turn on slopes unless necessary , and then, turn slowly and gradually downhill, if possible. • Do not mow near drop-off, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.
6 CAUTION W ARNING Look for this symbol to point out important safety precautions. It means CAUTION! BECOME ALERT! YOUR SAFETY IS INVOL VED. CAUTION In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
7 UNP ACKING INSTRUCTIONS • Remove all parts and packing materials from carton. TOOLS REQUIRED • 7 / 16 " Wrench or ratchet and socket • ½" Wrench or ratchet and socket • 7 / 8 &quo.
8 1. Remove the discharge chute from the deck. (Deck confi guration will vary by size and model) 2. Lower deck to the lowest cutting position. 3. Remove the right hand (discharge side) belt cover from the deck. 4. Relieve the tension from the deck belt and re- move from the center deck pulley .
9 ASSEMBL Y 1. Position blower over the discharge tabs on the deck and set blower onto the deck. 2. Be sure the blower is sitting fl ush against the outside of the deck. NOTE: The rear mount bracket is designed to fi t all deck sizes. 3. Install the front mount bracket to the deck with the pin and hairpin cotter supplied with the kit.
10 1. Using the hacksaw , trim the belt cover along the dashed line. 5 TRIMMING BEL T COVER (42" and 48" decks only) 6 INST ALLING BEL T COVERS 42/48 T rim Line 1. Place the deck belt shield on the deck over the drive pulley and secure with hardware removed from steel belt shield.
11 1. Remove the top right mount strap from the rear of the mower and save hardware. 2. Remove the right rear skid plate bolt and the lower right mount strap bolt from the mower and save hardware.
12 1. Remove the four carriage bolts indicated from the rear guard. 2. Install the bagger mount tube from the mount kit. 10 INST ALLING BAGGER MOUNT 3 Bin Collector Remove Kit Mount Strap Nut Hex Bolt Mount T ube 3. Remove the front carriage bolts securing the top mount straps to the frame.
13 11 INST ALLING CHUTE SUPPORT 3 Bin System only 1. Position upper chute support against bagger inlet, fl ush at outer edges. See Illustration. 2. Using support as a template, drill two 3 / 8 holes into bagger hood. Upper Chute Support Bagger Inlet Nut Bagger Hood Flat W ashers Hex Bolt Flex T rim 3.
14 12 INST ALLING WEIGHT KITS 1¼ Bolt Nut CAUTION DO NOT operate mower with grass catcher , unless the front weights are installed. 2¾ Bolt Weight Bracket Weight Plates 1. Bolt weight plates to weight brackets using four (4) 1¾" bolts and four (4) nuts.
15 NOTE: For ease of assembly , you may wish assistance from another person for mounting the cover assembly to mower . 1. Position cover assembly on ground behind mower . 2. Lift and rotate cover to align the cover bracket with hanger bracket and slide the cover down until secure.
16 TIPS FOR IMPROVED BAGGING Follow the mower operation instructions in you mower operator ’s manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time.
17 GENERAL RECOMMENDA TIONS Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades.
18 P ARTS 1 ... 539 108081 ... 1 ... SCREW , SPEC 10- 14 x ½ 2 ... 539 108082 ... 1 ... BAG DUMP INDICA T OR 3 ... 539 108083 ... 2 ... SCREW , 10- 24 x 1 1 / 8 4 ... 539 108084 ... 3 ... W ASHER, 3 / 16 x ¾ 5 ... 539 108085 ... 2 ... SP ACER, SPLIT 6 .
19 P ARTS ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 1 ... 532 124670 ... 1 ... RET AINER SPRING 2 ... 532 127533 .. 1 ... SCREEN, COVER 3 ... 539 108100 .. 1 ... GASKET , COVER 4 ... 532 130895 .. 1 ... LA TCH HANDLE, COVER 5 .
20 BAG ASSEMBL Y 539 131605 9 4 10 7 6 1 3 8 11 12 2 3 5 12 14 13 16 15 P ARTS.
21 1 ... 532 192709 ... 1 ... SCREEN, COVER 2 ... 532 195373 ... 1 ... COVER 3 ... 539 976952 ... 6 ... SCREW , #10-24 X 5 / 8 4 ... 539 108096 ... 2 ... SPRING, RET AINER 5 ... 539 108097 ... 4 ... PLUG, TUBING END 6 ... 539 108098 ... 1 ... BAGGER, FRAME 7 .
22 4 5 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 39 26 25 29 30 38 28 24 1 2 3 6 10 12 14 15 23 This side towards bearing 33 34 35 36 31 44 32 37 44 43 11 40 47 48 50 51 52 53 51 42 45 46 27 49 48 .
23 1 ... 539 101977 ... 1 ... TRACTION SPRING 2 ... 539 976952 ... 1 ... SCREW 10-24 x .625 RD 3 ....539 10441 1 ... 1 ... KNOB W/STUD 4 ... 539 104763 ... 1 ... RET AINER 5 / 16 “U” TYPE 5 ... 539 105785 ... 1 ... EURO DECAL, W ARNING 6 ... 539 106741 .
24 1 2 3 4 5 6 6 6 6 7 8 11 12 10 1 9 17 12 16 22 21 15 12 16 14 18 19 20 13 P ARTS.
25 1 ... 539 130305 ... 1 ... SHIELD, BEL T , 42" 2 ... 539 130306 ... 1 ... SHIELD, BEL T , 48" 3 ... 539 130307 ... 1 ... SHIELD, BEL T , 52" 4 ... 539 130308 ... 1 ... SHIELD, BEL T , 61" 5 ... 539 130319 ... 1 ... PULLEY , 42/48" .
26 1 2 5 3 4 1 ....539 1 13232 ... 1 ... WEIGHT PLA TE 2 ....539 1 13203 ... 2 ... WEIGHT BRACKET 3 ... 539 976979 ... 8 ... NUT 3 / 8 -16 HEX NYLOC ZD 4 ... 539 102612 ... 4 ... HCS 3 / 8 -16 x 2¾ GR 5 ZD 5 ... 539 976941 ... 4 ... HCS 3 / 8 -16 x 1¼ GR 5 ZD ITEM P ART NO.
539 130330 R3 01/22/08.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna O0803001 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna O0803001 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna O0803001, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna O0803001 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna O0803001, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna O0803001.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna O0803001. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna O0803001 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
