Manuel d'utilisation / d'entretien du produit 325HS75X du fabricant Husqvarna
Aller à la page of 20
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 325HS75 X-SERIES 325HS99 X-SERIES Oper ator ′ s manual Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Incorrect or careless use of a hedge trimmer can tur n it into a dangerous tool that can cause serious or ev en fatal injury . It is e xtremely impor tant that you read and understand the contents of this operator’ s manual.
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment.
4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es must be wor n when required, f or e xample when fitting, inspecting or cleaning cutting attachments. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction.
English – 5 SAFETY INSTR UCTIONS Vibration damping system Y our machine is equipped with a vibr ation damping system that is designed to minimise vibration and mak e operation easier . The machine ′ s vibration damping system reduces the transf er of vibration between the engine unit/cutting equipment and the machine ′ s handle unit.
6 – English SAFETY INSTR UCTIONS • Check that the throttle control and throttle loc k move freely and that the return spr ings work properly . • See instructions under the heading Star t. Star t the hedge trimmer and apply full throttle. Release the throttle trigger and check that the b lades stop and remain stationar y .
English – 7 SAFETY INSTR UCTIONS Assembl y of the catcher (accessory) Loosen the nuts on top of the bar . Align the bolts in the holes on the catcher and fit the bolts. Adjust the b lades' contact pressure according to the instructions under the heading Blades Gear housing • The gear housing gets hot when the machine has been in use.
8 – English SAFETY INSTR UCTIONS T ranspor t and storage • Store and transpor t the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, f or example , from electrical machiner y , electric motors, electrical relays/s witches or boilers.
English – 9 SAFETY INSTR UCTIONS • Check the w orking area for f oreign objects such as electricity cables, insects and animals , etc, or other objects that could damage the cutting attachment, such as metal items. • If any f oreign object is hit or if vibrations occur stop the machine immediately .
10 – English WHA T IS WHA T? What is what? 1 2 20 3 4 6 7 8 9 10 11 12 13 14 15 16 5 17 18 19 1 Operator ′ s manual 2 Grease nipple 3 Gear housing 4 Blades 5 Hand guard 6 F ront handle 7 Cylinder .
English – 11 FUEL HANDLING Fuel CA UTION! The machine is equipped with a tw o-stroke engine and must alwa ys been run using a mixture of petrol and two- stroke engine oil. It is important to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
12 – English ST AR TING AND ST OPPING Chec k bef ore star ting • Inspect the working area. Remov e an y objects that could be thrown out. • Check the cutting attachment. Ne ver use blades that are dull, crac ked or damaged. • Check that the machine is in perf ect working order .
English – 13 ST AR TING AND ST OPPING W arm engine Ignition: Set the stop s witch to the star t position. Choke: Set the choke control in the chok e position and then back to its original position. This only engages the star t throttle setting without any chok e.
14 – English MAINTENANCE Carb urettor Y our Husqv ar na product has been designed and manuf actured to speci fi cations that reduce har mful emissions.
English – 15 MAINTENANCE The blades m ust also remain stationar y when the chok e control is in the star t throttle position. W ARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact y our dealer/service workshop .
16 – English MAINTENANCE Cooling system T o keep the w orking temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder .
English – 17 MAINTENANCE Gear housing There is a grease nipple on the gearbo x. Use a grease gun to top up with grease. This should be carried out after appro ximately e very 20 working hours. Use Husqvarna special grease, No . 503 98 96-01. CA UTION! The gear housing must not be fi lled completely with grease.
18 – English TECHNICAL D A T A ´®z+H1|¶6A¨ ´®z+H1|¶6A¨ T echnical data Note 1: Noise emissions in the environment measured as sound pow er (L WA ) in conf ormity with EC directive 2000/14/EC .
English – 19 TECHNICAL D A T A EC-dec laration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-561 82 Huskv ar na, Sweden, tel: +46-36-146500, declare under sole responsibility that the h.
´®z+H1|¶6A¨ 2003-04-02 ´®z+H1|¶6A¨ 1140179-26.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna 325HS75X c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna 325HS75X - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna 325HS75X, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna 325HS75X va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna 325HS75X, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna 325HS75X.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna 325HS75X. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna 325HS75X ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
