Manuel d'utilisation / d'entretien du produit 322E, 325E-X du fabricant Husqvarna
Aller à la page of 24
Operator's Manual 101 89 75-26 322E 325E-X Read through the Operator‘s manual carefully and understand the content before using the machine..
2 – English EXPLANA TION OF SYMBOLS Symbols WARNING! The edger can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Always use: • A protective helmet where there is a risk of falling objects.
English – 3 CONTENTS List of Contents EXPLANA TION OF SYMBOLS Symbols ............................................................................... 2 CONTENTS List of Contents ................................................................... 3 SAFETY INSTRUCTIONS Personal protective equipment .
4 – English SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT INFORMATION • An edger used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual.
English – 5 5. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine’s exhaust fumes away from the operator. Mufflers equipped with a catalytic converter are also designed to reduce the hazardous substances in the exhaust fumes.
6 – English SAFETY INSTRUCTIONS IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine’s safety equipment. If the machine does not meet any of the controls listed below you should contact your service workshop.
English – 7 6. Cutting equipment SAFETY INSTRUCTIONS The two basic rules: 1. Only use the cutting equipment we recom- mend! See chapter “Technical data” . 2. Check the cutting equip- ment with regard to damage and crack formation. Damaged cutting equipment should always be replaced.
8 – English General safety instructions SAFETY INSTRUCTIONS IMPORTANT INFORMATION • The machine is only designed for cutting the edges of lawns. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data”.
English – 9 SAFETY INSTRUCTIONS Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.
10 – English SAFETY INSTRUCTIONS General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the edger. • If you encounter a situation where you are uncertain how to proceed you should ask an expert.
English – 11 SAFETY INSTRUCTIONS Safety instructions after completing work • Ensure the blade has stopped before cleaning, carrying out repairs or an inspection. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger.
12 – English WHA T IS WHA T? What is what on the edger? 1. Blade 2. Grease filler cap 3. Angle gear 4. Blade guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13.
English – 13 Assembling the blade ASSEMBL Y Fit the blade as follows: 1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fits in the hole of the blade is facing outward. 2. Block the blade rotation by inserting locking pin in the hole behind the blade guard engaging it in the corresponding hole in the drive disc.
14 – English Fuel mixture NOTE! The edger is fitted with two-stroke engines and must always be run on a mixture of petrol and two-stroke oil. To ensure the correct mixture proportions it is important to measure the quantity of oil accurately.
English – 15 ST ART AND ST OP Control before starting ! Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PURGE: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm.
16 – English Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in.
English – 17 Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter-clockwise until the cutting attachment stops.
18 – English MAINTENANCE Muffler with catalytic converter A muffler fitted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic.
English – 19 Lubricating the flexible drive axle Inside the edger‘s drive shaft is a flexible drive axle. The flexible drive axle should be regularly lubricated after 30 hours of operation. Loosen the two screws on the angle gear and remove it. The flexible drive axle is easily removed from the shaft by taking a firm grip on the axle end.
20 – English MAINTENANCE Maintenance schedule Below follows some general maintenance instructions. If you need further information please contact your service workshop. Weekly maintenance 1. Check the starter, the starter cord and the return spring.
English – 21 MAINTENANCE Monthly maintenance I. Clean the fuel tank using petrol. 2. Clean the outside of the carburettor and the area surrounding it. 3. Clean the fan wheel and the area around it. 4. Check the fuel filter and the fuel pipe, replace if necessary.
22 – English TECHNICAL DA T A T echnical data Engine Cylinder capacity, cu. in/cm 3 Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output axle, rpm Max.
English – 23 EU declaration of conformity (Only applies to Europe) (Directive 98/37/EC, Annex II, A) We, Husqvarna AB, S-561 82 Huskvarna, Sweden, tel.
´*2£T¶6N¨ 1999W37.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna 322E, 325E-X c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna 322E, 325E-X - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna 322E, 325E-X, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna 322E, 325E-X va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna 322E, 325E-X, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna 322E, 325E-X.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna 322E, 325E-X. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna 322E, 325E-X ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
