Manuel d'utilisation / d'entretien du produit 2748 GLS (CA) du fabricant Husqvarna
Aller à la page of 46
200 8 -0 3 O0 8 020 55 2 7 48 GLS ( C A) Operator's Manual Operator' s Manual Ride M o wer 960 43005000 03002.
.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS ( 2 ) Keys Slope Sheet Key (1) Oil Drain Tube TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Stan dard wrench sizes are listed.
6 AS SEMBL Y NOTE: Y ou may now roll or drive your tractor off the skid. Follow the ap pro pri ate instruction below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. W e rec om mend a wide vision safety mask over spectacles or stan dard safety glasses.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
11 OPERA TION REVERSE OPERA TION SYSTEM (ROS) Y our tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.
12 OPERA TION ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life).
13 FIG. 12 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
14 MAINTENANCE T R A C T 0 R I ns p e ct M u ff ler /Sp ar kA rres t er C lean A ir F il t er Ch an g e E n g ine Oil ( w i th o il f il t er) R e p la c e A ir F il t er P a p er C ar t ri dg e R e p.
15 MAINTENANCE FIG. 13 BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
18 SERVICE AND ADJUSTMENTS FIG. 17 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key .
19 SERVICE AND ADJUSTMENTS • From right side of mower , disconnect anti-sway bar (S) from right rear mower bracket (D) - remove retainer spring and washer and pull mower toward you until the bar falls from the hole in bracket. • T urn tractor steering wheel to the left as far as it will go.
20 • Engage belt tension rod (K) on locking bracket (L). CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly . • Raise attachment lift lever to highest position. • If necessary , adjust gauge wheels before op er at ing mower as shown in the Operation section of this manual.
21 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly . VISUAL SIDE- TO -SIDE ADJUSTMENT (See Fig.
22 SERVICE AND ADJUSTMENTS NOTE: Each full turn of the adjustment nut will change mower height about 1/8". • Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip. • Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.
23 SERVICE AND ADJUSTMENTS TO REPL ACE MOTION DRIVE BEL T (See Fig. 30) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual).
24 SERVICE AND ADJUSTMENTS FIG. 32 WEAK OR DEAD BA TTERY FULL Y CHARGED BA TTERY REPL ACING BA TTERY (See Fig. 33) WARNING: Do not short battery ter mi nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery , remove metal bracelets, wristwatch bands, rings, etc.
25 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
28 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
29 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
30 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 101 40 71 34 With Service Minder Option 46 46 With 12V O.
31 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Bat.
32 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 CHASSIS 14 214 130 130 37 194 194 181 181 182 68 68 189 176 176 176 175 178 165 228 228 183 194 236 235 152 150 202 203 204 210 .
33 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 CHASSIS KEY P ART NO . NO . DESCRIPTION 3 532 40 50-12 Logo Husq. 5 532 40 87-01 Dash 14 532 41 10-46 Hood 15 532 19 89-07 Lens .
34 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 DRIVE 56 171 216 143 197 196 125 226 125 125 80 125 51 52 170 175 279 176 178 174 22 23 166 276 153 233 drive-te x_K66_fender_1 .
35 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 DRIVE KEY P ART NO . NO . DESCRIPTION 1 532 41 41-45 T ransaxle, T uffT orq K66 2 532 00 70-70 Key 7 532 19 98-37 Hub Asm. Wheel 9 532 14 00-80 Bolt Hub Wheel 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
36 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26 1 45 61 2 6 steering-tex_4-husq 51 873 94 08-00 Nut Hex Jam T oplock 1/2-20 unf 53 532 18 89-67 Washer Hardened .
37 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 ENGINE 1 84 84 29 SP ARK ARRESTER KIT 84 45 18 15 37 28 37 22 21 20 62 71 70 79 69 87 2 engine-tex_bs-2cyl_2 81 82 12 11 41 42 90 85 9 91 31 KEY P ART NO . NO . DESCRIPTION 1 - - - - - - Engine B&S Model No.
38 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 SEA T ASSEMBL Y 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
39 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO .
40 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 MOWER DECK 47 7 54 46 32 33 31 30 1 33 52 48 43 50 97 33 49 39 185 46 46 6 21 122 114 98 31 32 25 26 24 27 194 113 17 21 49 187 .
41 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 87-00 Deck W eldment Mower 6 532 19 72-48 Cover Mandrel LH 7 532 19 91-02 Cover Mandrel RH 8 532 17 43-65 Bolt 7/16 Asm.
42 TRACTOR - MODEL NO . 2748GLS (96043005000), PRODUCT NO. 960 43 00-50 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-tex_3 91 89 87 89 87 2 532 19 52-23 Shaft Asm.
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
532 41 88-49 Rev 1 03-31-08 SBW/TH Printed in U.S.A..
SEC TION 1: LI MIT ED W ARRA NTY Husq varn a Fores t & Garden Compan y (“Husq varn a”) warr ants Husqva rna prod uct to th e origin al purc hase r to be free fr om defe cts in ma teria l and w.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna 2748 GLS (CA) c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna 2748 GLS (CA) - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna 2748 GLS (CA), vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna 2748 GLS (CA) va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna 2748 GLS (CA), mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna 2748 GLS (CA).
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna 2748 GLS (CA). Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna 2748 GLS (CA) ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
