Manuel d'utilisation / d'entretien du produit 260 ACX du fabricant Husqvarna
Aller à la page of 76
HUSQ V ARNA A UT OMO WE R ® 260 A CX OPER A T OR’S MANU AL.
.
TABLE OF CONTENTS English - 3 1. Introduction and safety .............................................................. 5 1.1 Introduction ..................................................................................... 5 1.2 Symbols on Automower ® .
TABLE OF CONTENTS 4 - English Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance and function of products without prior notice. This Operator's Manual deals with version 2.
English - 5 1. INTRODUCTION AND SAFETY 1. Introduction and safety 1.1 Introduction Congratulations on your choice of an exceptionally high quality product.
6 - English 1. INTRODUCTION AND SAFETY 1.2 Symbols on Automower ® These symbols can be found on the lawn mover. Study them carefully so you understand their significance. • Read through the Operator’s Manual carefully and understand the content before using your Automower ® .
English - 7 1. INTRODUCTION AND SAFETY 1.3 Symbols in the Operator’s Manual These symbols can be found in the Operator’s Manual. Study them carefully so you understand their significance. • Inspection and/or maintenance must be carried out with the main switch set to OFF .
8 - English 1. INTRODUCTION AND SAFETY 1.4 Safety instructions Use • Please read the Operator's Manual carefully and make sure you understand the instructions before using Automower ® . • It is not permitted to modify the original design of Automower ® .
English - 9 1. INTRODUCTION AND SAFETY Transport The original packaging should be used when transporting Automower ® over long distances. To safely move from or within the working area: 1. Press the STOP button to stop the mower. If the anti-theft alarm (see page 57) is activated; enter the first digit of the PIN code.
10 - English 2. PRESENTATION 2. Presentation This chapter contains information you should be aware of when planning the installation. An installation of Husqvarna Automower ® includes four main components: Automower ® , an automatic lawn mower that mows the lawn by moving in essentially an irregular pattern.
English - 11 2. PRESENTATION 2.1 Automower ® , what’s what? The numbers in the picture correspond to: 1. Charging strip 2. Cutting height adjustment cover 3. Catch button to open the cutting height adjustment cover 4. Ultrasonic sensors 5. Drive wheel 6.
12 - English 2. PRESENTATION 2.2 Function of Automower ® Capacity Automower ® 260 ACX is recommended for lawns up to 5500 m 2 +/-20%. How large an area is mown depends primarily on the condition of the blades and the type of grass, growth rate and humidity.
English - 13 2. PRESENTATION Working method Automower ® automatically mows the lawn. It continuously combines mowing and charging. The charging station sends out a signal that Automower ® can sense at a distance of 6 - 7 metres. The mower starts to search for the charging station when the battery charge becomes too low.
14 - English 2. PRESENTATION The control panel on the top of Automower ® is where you manage all the mower settings. The main switch is also located on the control panel.
English - 15 2. PRESENTATION 2.3 Search method Automower ® can be set to search for the charging station in three different ways. Using the setting options the three search methods can be combined to optimise the search for the charging station. The required search method or methods depends on the shape of the garden.
16 - English 2. PRESENTATION 2.4 More than one Automower ® in a garden I f you install more than one Automower ® in the same area of lawn, each mower must have its own PIN code. A complete installation, including charging station, is required for each mower.
English - 17 3. INSTALLATION 3. Installation This chapter describes how you install Husqvarna Automower ® . Before starting the installation read the previous chapter 2. Presentation . Read the whole of this chapter too before starting the installation.
18 - English 3. INSTALLATION • Screws for the charging station (24) • Measurement gauge (25) • Connector for the loop wire (23) • Solderless coupler for the loop wire (26) Contact your dealer .
English - 19 3. INSTALLATION Consider the distance to a wall socket when choosing the position. The charging station should be connected to a 230V wall socket via the low voltage cable and transformer. The supplied low voltage cable is 20 metres long.
20 - English 3. INSTALLATION Do not position the charging station so that the mower can come closer than 3 metres behind the charging station (for example on a narrow point). The mower will not then find the charging station. Installation and connecting the charging station 1.
English - 21 3. INSTALLATION 3.3 Charging the battery Automower ® is supplied with an uncharged battery. As soon as the charging station is connected, it is possible to charge the mower. 1. Set the main switch to the OFF position. 2. Place Automower ® in the charging station to charge the battery while you are laying the boundary wire.
22 - English 3. INSTALLATION Best position for the boundary wire The boundary wire should be laid so it: • Forms a loop around the working area for Automower ® . Only an original boundary wire must be used. This is tinned and has a high quality insulation to withstand the dampness in the ground.
English - 23 3. INSTALLATION Boundaries for the working area If a high obstacle, for example a wall or fence, borders the working area, the boundary wire should be laid 40 cm from the obstacle. This will prevent Automower ® from colliding with the obstacle and reduce body wear.
24 - English 3. INSTALLATION When Automower ® searches for the charging station or follows the loop according to the function Follow loop (3-2) (see page 50), it runs along the side of the boundary wire at a specific distance. The Corridor width (3-2-3) function determines the distance from the boundary wire that the mower shall run.
English - 25 3. INSTALLATION Secondary areas It is recommended to create a secondary area when the working area is made up of two areas that are joined by a passage where the distance between the boundary wires is less than 80 cm. Run the boundary wire then around the secondary area so that it forms an island outside of the main area.
26 - English 3. INSTALLATION Slopes The boundary wire can be laid across a slope that slants less than 10 %. The boundary wire should not be laid across a slope that is steeper than 10 %. There is a risk of Automower ® finding it difficult to turn there.
English - 27 3. INSTALLATION Laying out the boundary wire Run the boundary wire around the working area, but wait before connecting the wire to the charging station. Tip! Use the supplied measurement gauge as a guide when you lay out the boundary wire.
28 - English 3. INSTALLATION Laying the boundary wire in towards the charging station The boundary wire can be routed in several different ways in towards the charging station. The best alternative is to route the wire completely outside the charging station, see alternative 1.
English - 29 3. INSTALLATION 3.5 Connecting the boundary wire Connect the boundary wire to the charging station: 1. Lift up the cover on the charging station: • Grip under the edge of the cover with both hands and pull straight out towards the sides.
30 - English 3. INSTALLATION 3. Place the cable ends in the connector: • Open the connector. • Place the wire in the connector grip. 4. Press the connector together using a pair of pliers. Press until you hear a click. 5. Cut off any surplus boundary wire.
English - 31 3. INSTALLATION 7. Refit the cover on the charging station. Ensure the three guides on the charging station enter the right holes in the cover. 3.6 Checking the installation Check the loop signal by looking to see what indication the green LED on the charging station is giving.
32 - English 3. INSTALLATION 3.8 Installation of the guide wire The guide wire is an extra wire that is laid from the charging station, out towards a remote part of the working area or through a narrow passage and is then connected to the boundary wire.
English - 33 3. INSTALLATION • The route to a remote area is long or complicated. When Automower ® shall follow the boundary wire to or from a remote area and the route along the boundary wire to the area is long or complicated. • The boundary wire runs across a long slope (steeper than 10 %).
34 - English 3. INSTALLATION The longer the guide wire, the closer the mower follows the guide wire. If the guide wire is longer then 300 metres, the mower may find it difficult to follow the wire. This varies depending on the design of the garden and installation.
English - 35 3. INSTALLATION If you shall install the guide wire through a passage: • Automower ® follows the guide wire on the same side of the wire both to and from the charging station.
36 - English 3. INSTALLATION 3.9 Activate the GPS anti-theft protection area Before the anti-theft protection area can be activated, a SIM card must be installed and the administrator’s phone number must be entered into the GPS communication unit ( see 4.
English - 37 4. USE 4. Use 4.1 Charging a discharged battery When Husqvarna Automower ® is new or has been stored for a long period the battery will not be charged and needs to be charged before starting. Charging takes between 1 1/2 and 2 1/2 hours.
38 - English 4. USE 4.2 Using the timer The lawn should not be cut too often to obtain the best mowing result. Use the timer function (see 6.4 Timer (2) on page 47) to avoid a downtrodden lawn and to get the maximum life from your Automower ® .
English - 39 4. USE * hh=hours, mm=minutes (see 4.2 Using the timer on page 38 for more information on timer functions). ** Enter on/off for all the days of the week, Monday to Sunday. e.g. Swt On-Off-On-Off-On-Off-Off results in Automower mowing Monday, Wednesday and Friday.
40 - English 4. USE *** 1=English, 2=Italian, 3=German, 4=French, 5=Spanish, 6=Swedish, 7=Portuguese, 8=Dutch, 9=Danish, 10=Norwegian, 11=Finnish, 12=Polish, 13=Czech, 14=Slovenian **** From a security point of view, the administrator's number can only be set once from a mobile phone that is not that of users 2-5.
English - 41 4. USE 4.6 Restart Restart within 20 seconds 1. Close the control panel cover. Automower ® starts automatically. Restart after more than 20 seconds If more than 20 seconds has elapsed since the last time the STOP button or the keypad was pressed it is not possible to start Automower ® by just closing the cover.
42 - English 5. CONTROL PANEL 5. Control panel All forms of commands and settings for Husqvarna Automower ® are made via the control panel. All functions are accessed via a number of menus. The control panel consists of a display and a keypad. All information is shown on the display and all input is done using the buttons.
English - 43 5. CONTROL PANEL 5.1 Shortcuts 1. Home: • Sends the mower to the charging station. Where it stays until the button is pressed again. The house icon is lit on the right-hand side of the display when the button is pressed. When the battery is fully charged the mower will remain in the charging station and show the message Waiting .
44 - English 5. CONTROL PANEL 5.2 Select 3. Cancel: • Press to go back one step in the menu structure, or to interrupt an ongoing input. 4. YES: • Press to confirm an entry or selection. • Press to start the mower if more than 20 seconds has elapsed since you last pressed a button and you want to close the control panel cover.
English - 45 6. MENU FUNCTIONS 6. Menu functions 6.1 Main menu The main menu consists of four options: 6.3 Commands (1) 6.4 Timer (2) 6.5 Installation (3) 6.6 Settings (4) The numbers in brackets refer to the menu rows on the display of Husqvarna Automower ® .
46 - English 6. MENU FUNCTIONS 6.2 Automower ® main menu, menu overview Automower ® main menu Normal Test IN Test OUT Commands Timer Installation Settings Security Language Time and date PIN code Ti.
English - 47 6. MENU FUNCTIONS 6.3 Commands (1) This option in the main menu allows you to access the following functions on Automower ® . • Charge then AUTO (1-1) in order for Automower ® to drive immediately to the charging station, charge the battery and then return to the automatic operating mode.
48 - English 6. MENU FUNCTIONS Timer override (2-1) If you set the timer on your Automower ® , you can use this function to temporarily abandon the settings. • YES (2-1-1) Move the cursor to YES and press YES to turn off the timer function. • NO (2-1-2) Move the cursor to NO and press YES to turn on the timer function.
English - 49 6. MENU FUNCTIONS 6.5 Installation (3) From this option in the main menu you access the driving settings. • Exit angles (3-1) to set how far Automower ® should reverse out of the charging station before it turns and in what direction the mower should leave the charging station.
50 - English 6. MENU FUNCTIONS Follow loop (3-2) These functions in this sub-menu are for situations when the mower needs to be guided to reach remote areas, to find the charging station more easily, and to determine at what distance the mower shall follow the loop.
English - 51 6. MENU FUNCTIONS • Direction Specify to the right, left, guide 1 or guide 2 depending on which direction the area lies from the charging station. The direction is set looking from the charging station in the approach direction of the mower.
52 - English 6. MENU FUNCTIONS Automower ® 260 ACX has a default delay setting of 2 minutes for guide 1 and guide 2 and 11 minutes for the boundary wire.
English - 53 6. MENU FUNCTIONS Different corridor widths can be set for the boundary wire, guide 1 and on guide 2. The default setting on Automower ® 260 ACX is set to a value of 19 for both the boundary wire and guide wires. The higher the stated Corridor width value, the less risk there is of tracks forming.
54 - English 6. MENU FUNCTIONS When the function is selected the mower will immediately follow the boundary wire, guide 1 or guide 2, depending on which one it finds first, in to the charging station. If there is a passage and the mower can not run through it, the Corridor width value is set too high.
English - 55 6. MENU FUNCTIONS Installation shape (3-3) Automower ® can be set according to three garden shapes: Open , Normal and Complex . This setting affects how Automower ® covers a working area when it mows. Above all it influences the turning angles and how often the mower changes direction.
56 - English 6. MENU FUNCTIONS Security (4-1) • PIN code (4-1-1) Via this function you can change your PIN code at any time. • To change the PIN code: Move the cursor to PIN code and press YES . Place Automower ® in the charging station. Enter the new PIN code and press YES .
English - 57 6. MENU FUNCTIONS • Alarm(4-1-3) This function means that the first digit of the PIN code must be entered within 10 seconds after the STOP -button has been pressed or the mower has been lifted up for any reason. If the correct number is not entered after three attempts, the alarm sounds.
58 - English 6. MENU FUNCTIONS Language (4-2) Using this function you can change the language selection you made when Automower ® was first started. To select the language: Move the cursor to Language and press YES . Now move the cursor to the required language and press YES .
English - 59 6. MENU FUNCTIONS Sounds A number of audio messages are used to indicate what Automower ® is currently doing. Sound Significance 5 beeps over 2 seconds Starting blade disc One long beep .
60 - English 7. GARDEN EXAMPLE 7. Garden example - Proposed installation and settings The behaviour of the mower is controlled by the settings that are made.
English - 61 7. GARDEN EXAMPLE Area: 5500 m 2 . No guide wire is necessary. Timer : Operating time of 24 hours per day. Exit angles : 90° - 270°. Search method: Irregular and Follow boundary wire in. Delay: Guide 1 2 minutes, Guide 2 2 minutes and boundary wire 11 minutes.
62 - English 7. GARDEN EXAMPLE Area: 1600 m 2 . L-shaped garden with the charging station placed in the narrow area. There are two islands. No guide wire is necessary. Timer : Operating time of 8 hours per day. Exit angles : 250° - 290° Search method: Irregular and Follow boundary wire in.
English - 63 7. GARDEN EXAMPLE Area: 3000 m 2 . There is a number of islands. No guide wire is required. Timer : Operating time of 15 hours per day. Exit angles : 90°- 270°. Search method: Irregular. Delay: Guide 1 2 minutes, Guide 2 2 minutes and boundary wire 11 minutes.
64 - English 7. GARDEN EXAMPLE Area: 4500 m 2 . Two guide wires are recommended. Timer : Operating time of 24 hours per day. Exit angles : 90° - 270°. Follow loop out : Area 1; Direction Guide 1, Distance 40 m and Proportion 20 %. Area 2; Direction Guide 2, Distance 30 m and Proportion 40 % .
English - 65 8. MAINTENANCE 8. Maintenance Check and clean Husqvarna Automower ® regularly and replace worn parts if necessary to improve operating reliability and to ensure a longer service life. For further information on cleaning, see 8.5 Cleaning on page 67.
66 - English 8. MAINTENANCE 8.2 Winter storage Automower ® Automower ® must be carefully cleaned before winter storage, see 8.5 Cleaning on page 67. Charge the battery fully before winter storage.
English - 67 8. MAINTENANCE 8.4 After winter storage During a service the dealer can clean the mower thoroughly, test its function and components as well as replace wear parts if necessary. If the charging or contact strips appear to be burnt, clean them using fine grade emery cloth.
68 - English 8. MAINTENANCE Body Use a damp, soft sponge or cloth to clean the body. If the body is very dirty it may be necessary to use a soap solution or washing-up liquid. Take special care to keep the two ultrasonic sensors clean from dust and dirt at all times.
English - 69 8. MAINTENANCE To replace the blades: 1. Set the main switch to the OFF position. 2. Wear protective gloves. 3. Turn Automower ® upside down. 4. Rotate the skid plate so that its hole aligns with the screw for the blade. 5. Unscrew the blade.
70 - English 9. TROUBLE SHOOTING 9. Trouble shooting 9.1 Fault messages A number of fault messages are listed below that can be shown on Husqvarna Automower ® . If the same fault occurs frequently: contact your dealer. Fault message Cause Action Left wheel motor blocked Grass or other object has wrapped around the drive wheel.
English - 71 9. TROUBLE SHOOTING Outside working area If this occurs in isolated areas it may be due to interference from metallic objects (perimeter fence, reinforcement bar) or buried cables in the vicinity. Try moving the boundary wire. The working area slopes too much.
72 - English 9. TROUBLE SHOOTING 9.2 Fault symptom If your Automower ® does not work correctly, follow the trouble shooting guide below. If the fault persists; contact your dealer. Symptom Cause Action Uneven mowing results Automower ® works too few hours per day.
English - 73 10. TECHNICAL DATA 10. Technical data 11. Environmental information The symbol on Husqvarna Automower ® or its packaging indicates that this product may not be treated as household waste. It should instead be left at a suitable recycling centre to recycle its electronic components and batteries.
74 - English 12. EU DECLARATION OF CONFORMITY 12. EU declaration of conformity EU Declaration of Conformity (only applies to Europe) Husqvarna AB , SE-561 82 Huskvarna, Sweden, hereby declares that ro.
.
11 5 39 76 - 26 ORIGI NA L I NS T RUCT IONS A U TOMO W E R ® is a t radema rk ow ned by Husq var na A B . Copy r ight © 201 1 H USQV A R NA . A ll r ights re ser ved.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Husqvarna 260 ACX c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Husqvarna 260 ACX - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Husqvarna 260 ACX, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Husqvarna 260 ACX va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Husqvarna 260 ACX, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Husqvarna 260 ACX.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Husqvarna 260 ACX. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Husqvarna 260 ACX ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
