Manuel d'utilisation / d'entretien du produit TCR ID-10 du fabricant Humminbird
Aller à la page of 19
.
TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefully consider the f ollowing before installing your transducer.
by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it back in place.
Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the center of the Bracket slots. On some alu minum boats it may be necessary to use a wood back - up plate.
NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water level. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied.
Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the headed pin and in sert it through the two parts.
wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly fastened to the pivot . (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the bottom of the transom.
7. Remove the water and transducer and clean the marked area and t he bottom of the transducer thoroughly. 8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted.
Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilted to any desired position..
OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommend ed since the unit cannot be rotated.
It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”.
.
Specifications: Operating Frequency 200 KHz Power Requirement 12 volts Power Cable Length 111/2' Transducer (standard) XHS-6-16 high-speed Transducer Cone Angle 16 degrees Transducer Cable Length.
NOTE: The built - in simulator will allow y ou to practice adjusting the sensitivity, but your adjustments will not change readings being displayed on the screen. READING THE TCR ID - 10 SCREEN Your TCR has a liquid crystal display, or LCD. The liquid crystal material in the display aligns itself to either block light or let light pass through.
60' scale and it changes to the 0 - 30' scale, the entir e screen will look as if you had been in the 0 - 30' range all along. 2. Using zoom and bottom - lock. Through Pixel Memory Capacity, the memory in the TCR ID - 10 stores readings in much finer detail than is displayed in the "regular mode.
Of course, the best way t o learn to read your TCR ID - 10 is to use it, especially in familiar locations. If you know what's underwater and can see it displayed on the screen, then you're on your way to being an experienced TCR user.
OPERATING THE TCR ID - 10 Your new TCR ID - 10 offers unique automatic features, as well as many adjustable ones. If you're learning to operate the TCR ID - 10 with its simulator, follow the directions listed at "Built - In Simulator" on page 16, and then come back to this page.
The following describes the functions and how to use them, in order of appearance after you turn the unit on. 1. Sensitivity Automatic setting: on, "O" or normal As conditions change, the computer will automatically increase or decrease the sensitivity setting.
buttons, you can move the zoom window while the zoom is activated, without having to press Select again. 5. Bottom - Lock Automatic setting: off You can easily turn on the bottom - lock with the On/Off button. When on, this function shows up - close zoom r eadings in reference to the bottom.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Humminbird TCR ID-10 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Humminbird TCR ID-10 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Humminbird TCR ID-10, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Humminbird TCR ID-10 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Humminbird TCR ID-10, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Humminbird TCR ID-10.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Humminbird TCR ID-10. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Humminbird TCR ID-10 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
