Manuel d'utilisation / d'entretien du produit P/N 21147703 du fabricant Huffy
Aller à la page of 28
1 03/04 P/N 21147703 © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 21147703 03/04 W ARNING F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net.
03/04 P/N 21147703 3 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p arts are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to instructions.
4 P/N 21147703 03/04 Get to know the basic parts of your basketball system..... FRONT T OP POLE BACK MIDDLE POLE FRONT COVER RIM BOTT OM POLE STRUTS ELEV A TOR ASSEMBL Y BACKBOARD BASE WHEEL CARRIAGE .
03/04 P/N 21147703 5 Item Qty Part No. Description 1 1 908026 Top Pole Section 2 1 908107 Middle Pole Section (with Label) 3 1 908015 Bottom Pole Section 4 1 900223 Wheel Bracket 5 1 206940 Axle 6 2 2.
6 P/N 21147703 03/04 HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #14 (2) Item #31 (4) Item #55 (1) Item #44 (4) Item #1 1 (21) Item #9 (6) Item #50 (6) Item #19 (1) Item #29 (4) Item #10 (18) Item.
03/04 P/N 21147703 7 Item #20 (8) Item #42 (1) 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1.
8 P/N 21147703 03/04 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolts into large holes of elevator tubes, backboard bracket s and triangle plates.
03/04 P/N 21147703 9 SECTION A: ASSEMBLE THE POLES W ARNING LABEL 2 1 3 I.D. Label I.D. Label 1. Correctly identify each pole section. 2. WOOD SCRAP (NOT SUPPLIED) 2 1 Align dimple of top pole with slot of middle pole.
10 P/N 21147703 03/04 Align dimple of middle pole with slot of bottom pole. While maintaining alignment, bounce top and middle pole assembly (1 & 2) onto lower pole section (3) as shown until they no longer move toward pole identification mark. 3.
03/04 P/N 21147703 11 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this .
12 P/N 21147703 03/04 11 15 10 2. Attach pole assembly to base using carriage bolts (15) washers(10) and nut s (1 1) as shown. T wo people are required for this step. 1. Assemble pole bracket (12) to pole (3) using bolt (13) and locknut (14) as shown.
03/04 P/N 21147703 13 3. Rotate non-secured ends of t ank struts (16) outward to mounting holes in tank as shown.Secure ends of tank strut s (16) to tank as shown. Repeat for opposite side. 9 10 11 10 16 16 4. 10 10 14 17 13 16 TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
14 P/N 21147703 03/04 5. 6. Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using pushnuts (7). Carefully t ap pushnuts onto axle with hammer or mallet 4 6 6 7 7 5 Install wheel assembly to base (8) using bolts(9), washers(10) and nut s (1 1) as shown.
03/04 P/N 21147703 15 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION C: ASSEMBLE THE ELEV A TOR & BACKBOARD This is what your system will look like when y.
16 P/N 21147703 03/04 1 . Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolt s (22) as shown. T ighten flange nuts (1 1) completely . 1 28 11 11 18 22 22 2. Attach sp acers (24, 43) to pole mount bracket (28) with bolts (29), washers (44), and lock nuts (31) as shown.
03/04 P/N 21147703 17 3 . 28 11 27 35 35 26 19 Apply logo and height indicator labels (23) to adjustment rod (51) as shown. Attach handle part s (52, 53) to adjustment rod with screw (55), carriage bolts (54), and flange nut s (1 1) as shown. 4 . 54 11 11 53 52 55 54 51 23 23 Assemble lanyard (26) to locking pin (27) as shown (FIG A).
18 P/N 21147703 03/04 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (27). 27 5 . 6. 30 30 29 29 31 45 Assemble backboard brackets (45) using spacers (30), bolt s (29), and nuts (31) as shown.
03/04 P/N 21147703 19 7. 50 48 49 45 21 Attach lower elevator tubes (34) and counter balance spring (48) to backboard support brackets (45) using sp acers (46 & 49), bolt (50), and nut (21) as shown. NOTE: Rim mounting nuts and bolt s supplied with rim hardware.
20 P/N 21147703 03/04 8. Attach upper elevator tubes (33) to backboard support bracket s (45) using spacers (46 & 49), bolt (50), and nut (21) as shown. 50 49 49 21 46 33 33 33 49 45 49 21 46 50 33 IMPORT ANT!: TIGHTEN ALL HARDW ARE FROM STEP 6 - 8 AFTER THIS ASSEMBL Y IS COMPLETED.
03/04 P/N 21147703 21 21 21 47 25 34 1 32 32 50 20 34 20 9. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Install pole cap (25). 50 33 20 21 1 21 33 20 32 51 10. Install upper elevator tubes (33) to triangle plates (32) as shown.
22 P/N 21147703 03/04 33 48 21 33 51 11 . Insert bolt (50) through left side upper elevator tube (33), then stretch spring (48) onto bolt (50). Insert bolt (50) through right side upper elevator tube (33) and secure with nut (21). 50 48 USE EYE PROTECTION WHEN INST ALLING SPRINGS.
03/04 P/N 21147703 23 1. SECTION D: SECURING THE SYSTEM Roll assembly to desired playing area. Secure assembly to ground using rope (56) and tie down stake (36). Fill base (8) with water (approx. 40 gallons) and snap fill caps (37) in place. 56 36 37 8 37 TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
24 P/N 21147703 03/04 SECTION E: INST ALL FRONT COVER 1. Install front cover (38) by lining up st and-offs along the tank strut s. Insert a tie strap (39) through the top two and bottom two stand of fs. Wrap tie strap s around tank struts as shown and secure tightly .
03/04 P/N 21147703 25 1. Install clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
26 P/N 21147703 03/04 Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP 2.
03/04 P/N 21147703 27 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position.
28 P/N 21147703 03/04 SECTION H: HEIGHT ADJUSTMENT 1. A. While holding handle, remove pin (27). B. Move elevator up or down to desired height. C. Replace pin (27) full length to lock system at desired height. 27 A. B. C. 51 DO NOT ALLOW CHILDREN TO ADJUST HEIGHT .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Huffy P/N 21147703 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Huffy P/N 21147703 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Huffy P/N 21147703, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Huffy P/N 21147703 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Huffy P/N 21147703, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Huffy P/N 21147703.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Huffy P/N 21147703. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Huffy P/N 21147703 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
